Husk based power plant 6 t 32 kg fbc with single stage turbine for finance, subsidy & project related support contact - 9861458008

Ref : IB/D/Q113/113/13
Date : 04th Jan. 2013
Mr. Santosh Agarwala
M/s Sonthalia Rice Mill.,
S3/36,37, Sec-A, Zone –B,
Mancheshwar Indl. Estate,
Bhubhneshwar (Orissa)
Dear Sir,
As desired by you, we are pleased to submit our offer for high pressure
husk fired FBC boiler and Back Pressure Steam Turbine for co-generation
purpose.
While designing the system, we have assumed the following data:-
Boiler Capacity from feed water at 900C 6000 Kg/hr
Steam Flow to Turbine / Plant Consumption 4000 Kg/hr
Steam temperature at Boiler Outlet 350 +/-10 0C
Boiler Design Pressure 32 Kg/cm2
Steam temperature at turbine inlet (max) 350 0C
Turbine Inlet pressure 30 Kg/cm2
Outlet Pressure of Steam from Turbine(max) 3.50 Kg/cm2
Power Output based on above steam demand 202 KW / 252 KVA

For the purpose of clarity and simplification our quotation is grouped separately as
follows.
BOILER DATA
Design Data Annexure - I
Scope of Supply. Annexure - II
Technical Specification. Annexure –III
TURBINE DATA
Material Specification Of Turbine Annexure - IV
Turbine Technical Information Annexure - V
COMMERCIAL DATA
Commercial Offer Annexure- VI
General Terms & Conditions. Annexure - VII
We hope you will find this quotation informative and we look forward to your
comments and suggestions to fine tune the system to suit your requirements.
Thanking you,
for INDUSTRIAL BOILERS LTD.
INDUSTRIAL BOILERS LTD, 79-80 SATKAR, NEHRU PLACE , NEW DELHI
- 2 -
H.S.ANAND
Executive Director
Mob : 09350169001
HUSKOGEN

ANNEXURE - I
BOILER DESIGN PARAMETERS
Unique features of the Huskogen Boiler
¾ Unique Non Membrane Radiant water tube design furnace.
¾ Straight Tube convection Bank.
¾ Microprocessor based Continuously Modulating fuel feeding.
¾ Expandable Boiler thru In-bed tubes for long life.
- 3 -
¾ Seamless in bed tubes
¾ Super heater tubes suitable for 370 Deg C
¾ Stainless Steel Fluidising Air Nozzles.
¾ High Efficiency TREXMA Dust Collector.

The following parameters have been taken as the basis for the design of
the proposed boiler.
Boiler parameters at Maximum Continuous Rating :-
Steam flow at Superheater outlet 6000 kg/hr
Steam pressure at superheater outlet 32.00 kg/cm² (g)
Steam temp. at superheater outlet 350°C ± 10°C
Superheater temperature control range 75 - 100% load
Feed water temp. at inlet to Boiler 90° C
The Type of Boiler selected is :-
Location Indoor
Type of Boiler Single Drum, Water Tube, Natural
Circulation
Combustion system Fluidised Bed
Draft system Balanced draft
Support Bottom supported on RCC construction.
Fuel Specifications
• Primary Fuel Rice Husk
• GCV of Rice husk 3300 Kcal/Kg (Moisture -6 %)
ƒ Emergency Fuels Coal, Lignite. (Size < 6 mm)
• Start up Fuel Kerosene + Charcoal (Size15 – 30 mm)
Site Conditions :-
Ambient temp (for design) 40°C
Relative humidity (for design) 60%
Wind load As per IS 875
Seismic coefficient As per IS 1893
- 4 -

Codes & Standards :-
Pressure parts As per IBR with its latest amendments.
Non pressure parts As per our Standard Engineering Practice.
Boiler Thermal Efficiency As per BS 845 Part I, Indirect method.
Radiation loss As per standard ABMA radiation loss chart
Utility Requirements :-
Electrical Requirements for Motors
Voltage 415 ± 6% V
Frequency 50 ± 3% Hz
Phase 3 phase, 4 wire
Electrical Requirements for Instrumentation and Panel
Voltage 230 V
Frequency 50 Hz
Phase Single Phase
INSTRUMENT AIR
Pressure 7.0 Kg/cm² g
Quality Dry, free from oil & dirt
Dew point temp. - 15° C
BED MATERIAL
Material Sieved Natural river bed sand /
Crushed Refractory
Size 1 to 2.5 mm
Bulk density 1200 to 1500 Kg/m3
Melting Point + 1500oC
COOLING WATER REQUIREMENT
Quantity 0.5 m3/hr
Temperature < 40 oC
- 5 -

ANNEXURE - II
SCOPE OF SUPPLY
HUSK GEN MODEL FBC FIRED BOILERS
CONSTRUCTION :
The Fluidised Bed Boilers offered by us are made as per the latest IBR
Regulations and are of Class-I Fusion welded construction. Stringent
quality control is observed at every stage of manufacture right from raw
material stage to testing of Boiler prior to dispatch. The pressure parts
are manufactured from Boiler Quality Steel, fully welded construction,
shell radiograph and hydraulically tested.
One Steam Cum Water drum which incorporates the Smoke Tube boiler
bank.Water tubes are provided within the combustion area to maintain a
furnace temperature range of 6500C to 7500C. These tubes are connected
with header at the bottom along with downcomers to form a natural water
circulation circuit.
A convective evaporator section consisting of a Smoke tube boiler section
is so designed as an inline arrangement.
FLUE GAS PATHS :
The Boiler consists of a configuration enabling high turn down ratios. The
combustion once completed in the bed is released into the free board
zone at a temperature slightly higher than 750oC. The Water Tubes
absorb the heat before leading the gases into the super heater zone and
then to Smoke tube boiler section (Convection Bank). The flue gases are
then taken into an APH, Dust Collector, I.D.Fan and into the chimney.
STEAM CUM WATER DRUM
The boiler consist of one Steam cum water drum. This drum connects the
Risers and Downcomers to various Heating Surface Sections within the
Boiler. Feed Water is fed from the Feed Pumps into this drum. Water level
is maintained in the drum thru Mobrey control provided.This drum also
contains the Convection Bank of Tubes.The Drum is provided with Hinged
doors at the Rear for easy approach and Cleaning. A Blowdown
connection is provided to remove the sludge during operation.
- 6 -

FERRULES :
Stainless Steel Ferrules are provided at the entry of
Furnace gases to the smoke tubes. These protect and
increase the life of the smoke tubes.
WATER TUBES :
Tubes of BS 3059 ERW grade are used for Water tubes in the furnace
zone. These tubes maintain proper Furnace temperature to prevent
overheating and clinker formation.
CONVECTION BANK TUBES :
Tubes of BS 3059 ERW grade are used for the convection Bank.
These are all straight tubes which can easily be replaced when required.
The first pass tube is protected from erosion at the ends thru Stainless
Steel Ferrules.
INBED TUBES :
Extra Heavy and Thick Seamless In-Bed Tubes are provided directly
immersed within the Fluidising area. These tubes are directly connected
to the Steam Drum at the Top thru separate Risers and Downcomers.
HEADERS :
Extra Thick Seamless headers as per BS3059/ASTM 106
are provided. The headers have one side opening and the
tube holes are drilled on them.
MOUNTINGS & FITTINGS (STEAM DRUM) :
One Air Vent Valve.
Two Single Post Safety Valves.
Two Sets of Water level gauges.
One Pressure gauge with siphon and cock.
One Inspectors pressure gauge cock.
One Blow down valve.
MOUNTINGS & FITTINGS (WATER DRUM) :
- 7 -
One Feed Stop valve.
One Feed Check valve.

MOUNTINGS & FITTINGS (WATER WALL HEADERS) :
- 8 -
Two Blow down valves.
MOUNTINGS & FITTINGS (INBED HEADERS) :
MOUNTINGS & FITTINGS (SUPER HEATER) :
One Main Steam Stop Valve
One Air Vent Valve.
One Single Post Safety Valve.
One Drain valve on header.
FEED PUMPS :
Two numbers (One duty and One stand by)
electrically driven reciprocating Feed Pumps with
motors will be provided.
AUTOMATIC WATER LEVEL CONTROL :
Feed water regulating system to ensure correct water level in the Boiler.
In case of extreme low water level an alarm is provided. The system
consist of the following :
¾ A level controller with a control valve to maintain the correct water
level in the boiler drum.
¾ Manual Pump on / off control to start and stop the pump to maintain
the desired water level in the boiler in case of an emergency.
¾ High & Low water level Annunciation system with an audio (Alarm)
& visual indication is given.
¾ In case of extreme low water the boiler goes in a lock out
condition and the an audio (Alarm) & visual indication is given.
¾ An Mobrey control is provided for additional safety. In case of
extreme low water the boiler goes into a lockout condition and an
audio & visual indication is given.

CONTROL PANEL :
The panel consist of a sophisticated but user friendly circuit enabling the
operator to run the boiler in automatic or manual mode as desired.
Various instruments and safety features are as detailed
below:
In auto mode the boiler will operate all sequences
automatically. The boiler can be also adjusted to start
and stop automatically within a pressure range of 3 to 5
Kg/cm2. However in case of Low Loads, below 75% of
MCR, steam superheat temperature will differ from
Designed Values.Initially during pre fluidisation state the
boiler needs to be started manually.
The Panel is lockable by a key to prevent unauthorised operation of the
boiler. The MCC will be fixed (non-draw out) type modular with single front
and is suitable for indoor application. The cable entry will be from bottom.
In the control panel Switches, Motors Starters, Indication Lamps, Control
Fuses, Main Incoming Switch and Inter connecting wiring for the following
is provided.
F.D. Fan
I. D. Fan
Feed Pumps (2 Nos.)
Fuel Feeder
Temperature indicators with selector switch.
Annunciation windows to show unhealthy operation for the following are
provided:
- 9 -
F. D. Fan Trip
I. D. Fan Trip
Feed Pumps Trip
Fuel feeder Trip
Drum Level Low
Drum Level High
Bed Temperature high

MICRO PROCESSOR BASED FUEL FEEDING :
Microprocessor based indicator cum controller(s) is provided
for Fuel Feeding. The controller senses the temperature of
fluidisation and delivers a precise signal to the dynodrive(s)
to increase / decrease the fuel feeding rate. By the use of
this advanced micro processor technology precise control of
feel feeding is maintained leading to Low excess air losses
and subsequently a very high fuel efficiency.
FORCED DRAFT FAN :
The Forced Draft Fan provides air for combustion. This Fan is a
Centrifugal machine with impellers directly fitted onto the Motor Shaft. A
Damper on the Inlet is provided to control the Air Flow. The D fan includes
a drive Motor.
INDUCED DRAFT FAN :
The Induced Draft Fan removes Flue Gases by Suction from the Boiler.
This Fan is a Centrifugal machine with impellers fitted to a Shaft which is
driven by Pulleys from a motor. A cooling Disc is provided on the shaft to
cool it sufficiently before the heat reaches the Pulley Blocks.
The Impellers are lined at crucial Places by Hard, Wear Resistant Liners.
A Damper on the Inlet is provided to control the Gas Flow.
AIR HEATER :
A Multi tubular Air Preheater having a cross flow of Air to flue gases is
Provided. The Flue Gases move in Two Passes, substantially transferring
the heat before gases exit to the ID Fan.
A Rotary Air Lock Valve is provided at the bottom of the Air Preheater to
continuously discharge the Ash collected.
Inlet / outlet manifolds of the Air and Flue gases are provided.
SMOKE DOORS :
Easily operational double hinged type doors are provided at the Back end
of the Boiler to give clear access to the tubes.
- 10 -

MANHOLE :
A large size manhole is provided at the top to give
convenient access to the water side of the shell.
DUST COLLECTOR :
A highly efficient Cyclone Type TREXMA Dust Collector is
provided to check carry over the dust particles which
otherwise would escape to the
atmosphere. The precipitator separates the dust particles
by the use of centrifugal and gravitational forces. Ash is
continiously discharged from the Bottom of the dust
collector. The Dust Particulate Emission is well within most
Pollution Norms.
STRUCTURE :
The Boiler is mounted on its chairs which are in turn placed
on Civil Structures.
NSTRUMENTATION AND SAFETY INTERLOCKS :
The system offered is extremely simple and convenient to operate.
Amongst the Instruments provided are :-
Bed Temperature Indicator cum controller
Bed Height Indicator. (Indirect Indication)
Fuel Feeder Speed Indicator.
Water Level Controller cum Alarm.
Multiple point annunciator for displaying unhealthy operating conditions.
The following are a few of the safety interlocks :-
In case of high bed temperature the feeders shut down.
In case of high steam pressure the boiler fans and feeders shut off.
In case of low water the pumps operate.
In case of extreme low water level the whole system automatically goes
into a lockout condition.
- 11 -
EMISSION
GUARANTEED
LESS THAN 350
mg/Nm3

DRAWINGS & DOCUMENTS :
We shall provide tentative drawings showing the general layout and the
foundation plans. This will only be used as guidance by our clients as the
site location will vary from place to place.
A complete set of Drawings and Documents duly certified by the
Inspecting Authority of the State of Origin will be given within 4 to 6 weeks
after the dispatch of the boiler.
BATTERY LIMITS :
Water - Inlet of Feed Pumps and Drum
Steam - Outlet of Main Steam Stop Valve at Superheater
Blow down - Outlet of Blow down Valves
Drain - Outlet of Level Gauges and Controllers
Ash - Outlet of Dust Collector, Air Preheater
- Outlet of Gates at Boiler
- Outlet of Slide Gates for Bed Ash removal
Flue Gas - Outlet of Boiler
- In & Out of APH and Dust Collector
- Suction and Delivery of I.D. Fan
Electricals - Inlet of all motors and controls and panel
Fuel - Inlet of Screw Feeder
- 12 -

EXCLUSIONS :
# Water treatment plant.
# Main Chimney and Flue Duct between boiler, Heat Recovery
Unit, Dust Collector and Chimney.
# Interconnecting Ducting of Air Preheater
# Fuel handling system upto screw feeder.
# Feed Water Tanks, Feed Water Piping upto the terminal point.
# Steam, Blow down and Drain Piping from terminal Valves on
- 13 -
the boiler.
# Insulation of boiler and Steam pipeline.
# Refractory Materials for the Furnace.
# Structural materials such as platform, ladders, supports, etc.
# All civil and structural design work for installing the boiler.
# Electrical work in the boiler house upto the terminal points and
interconnecting cables.
# Instrument and accessories for performance test.
# Labour, Tools, Tackles, Utilities, Consumables like charcoal,
Kerosene, Inert, materials, cleaning and lubricating agents
required for assembling, erecting and commissioning of the
boiler.

ANNEXURE - III
TECHNICAL SPECIFICATIONS OF BOILER
Max. continuous rating : 6000 Kg/hr (From 90oC)
Type of Boiler : Fluidised Bed Combustion
Model No. : HUSKO-60
Design Code : Indian Boiler Regulations
Safety valve set pressure : 34 Kg/cm2
Design Pressure : 32 Kg/cm2
Hydraulic Test Pressure : 48 Kg/cm2
Superheat Temperature : 350oC +/- 10oC
Feed water Temperature : 90oC
Thermal Efficiency : 80% +/- 2%
as BS:845 Pt. 1 Indirect Method
Fuel consumption on GCV of : 1480 Kg/hr at 6 TPH load
Husk 3300 Kcal/Kg.
Material Specifications :
Boiler Drums : ASTM 515/516 Gr 60/70
Headers : ASTM 106 Gr B
Boiler Tubes : BS 3059 Pt 1 ERW
Super Heater Tubes : BS 3059 Pt 1 ERW
In Bed Tubes : BS 3059 Pt 1 Seamless
Fluidised Bed Nozzles : AISI Stainless Steel 304
Ferrules : AISI Stainless Steel 304
- 14 -

F.D. Fan details :
Type : Centrifugal Direct Drive
Motor : 30 H.P.
CFM : 5250
Pressure : 600 mm
RPM : 2900
Quantity : 1 No.
I.D. Fan details :
Type : Centrifugal V- Belt Drive
Motor : 25 H.P.
CFM : 9000
Pressure : 250 mm
RPM : 1200
Feed Pump details
Type : Reciprocating
Flow : 8000 Ltr/hr
Head : 36 Kg/cm2
Motor : 20 HP
No. of pumps : 2 Nos.
Fuel Feeder details :
Type : Screw Feeder
Control : Variable Speed Dynodrive
Motor : 1 HP
Gear Box Ratio : 1:20
No. of Feeders : 1 No.
Velocity Profile :
Fluidised Bed : 3 – 2 m/sec
Freeboard Zone : 8 –10 m/sec
Superheater Zone : 6 – 8 m/sec
Convection Bank : 20 – 15 m/sec
Air Preheater Bank : 20 – 25 m/sec
Dust Collector : 250 – 100 m/sec
Gas Ducting : 8 – 10 m/sec
Chimney : 6 –8 m/sec
- 15 -

Temperature Profile
Fluidised Bed : 700 – 800oC
Free Board : 1000 - 1200oC
Exit of Radiation Zone : 500 – 600oC
From Boiler : 240 – 260oC
After Air Preheater : 150 – 180oC
Draft Losses Profile
Boiler : 25 mm WG
H.R.U. : 40 mm WG
Dust Collector : 100 mm WG
BOILER VALVE SIZING
MOUNTINGS & FITTINGS (STEAM DRUM) :
One Air Vent Valve.
Two Single Post Safety Valves.
Two Sets of Water level gauges.
MOUNTINGS & FITTINGS (WATER DRUM) :
One Feed Stop valve.
One Feed Check valve.
MOUNTINGS & FITTINGS (WATER WALL HEADERS) :
Two Drain valves.
MOUNTINGS & FITTINGS (INBED HEADERS) :
One Drain valve.
MOUNTINGS & FITTINGS (SUPER HEATER) :
One Main Steam Stop Valve
One Air Vent Valve.
One Single Post Safety Valve.
One Drain valve on header.
- 16 -

FEED WATER SPECIFICATIONS
Deaerated and Demineralised water is recommended for the boiler.
Feed water should meet the following requirements.
Water Hardness : 0.2 ppm max.
pH : 8.5 - 9.5
Dissolved Oxygen : 0.1 ppm max.
Oil Content : Nil
TDS : 200 ppm max.
BOILER WATER SPECIFICATIONS
Water Hardness : 0.5 ppm max.
Total Alkalinity ( as CaCo3 ) : 700 ppm max. but
- 17 -
not exceeding 20% of TDS
Caustic Alkalinity ( as CaCo3) : 350 ppm max.
pH : 11 - 12
Unreacted Sodium Sulphate (as Na2So3) : 30 -50 ppm.
Phosphates ( as Po4 ) : 20 - 40 ppm.
TDS : 1000 ppm max.,
Residual Hydrazine ( as N2H4 ) : 0.5 ppm max.
FUEL SPECIFICATIONS FOR GUARANTEES
Fuel : Husk
Moisture : <10%
Calorific Value : 3300 Kcal/Kg
Impurities : Nil

UNIQUE FEATURES OF IBL BT-4 TURBINES
¾ Horizontally Split Steam casing.
Permits easy inspection of the internals without disturbing
the steam lines.
¾ True Centre line support.
Enables equal expansion of all the components, permitting
safe and quick startup. Allows precise alignment of the
turbine with the driven machine.
- 18 -
¾ Curtis Blades.
Two sets of blade rows to achieve higher efficiency.
¾ Pressurised Lubrication.
The Bearings of the Turbine and the gearbox are supplied
with a Forced Lubrication and a Oil Cooling system which
enables the turbine to run smoothly and effortlessly.
¾ Metaflex Couplings Type
High Speed metaflex type couplings are provided between
the Turbine and Gearbox. These couplings have
outstanding flexibility at high speeds.
¾ Loaded with safety features.
All standard features such as Emergency valve, Over speed
governor, High Pressure trip, Low Lube Oil Pressure trip.

ANNEXURE - IV
MATERIAL SPECIFICATIONS OF IBL BT-4 TURBINE
CASTINGS
The Castings are made out of robust alloy steel of Radiography quality.
The casing is split horizontally at the center line, permitting easy access to
the interior for inspection without disturbing the steam inlet and outlet
lines. Centre line support ensures precise alignment of the turbine with
driven machine.
WHEEL
The Forged wheel is accurately profiled and machined to very close
tolerances, and located between heavy duty Bearings for continuous and
long operations. The Built-up Rotor is dynamically balanced to a high
degree of accuracy to ensure vibration free, smooth, and years of trouble
free operation of the Turbine.
SHAFT
The shaft is made out of Forged Carbon Steel & the Section under the
Carbon glands is chrome plated to minimize erosion & corrosion.
NOZZLES
Nozzles are made of S.S. and manufactured with High accuracy as per
the specified Steam parameters for developing optimum efficiency.
BLADES
These are manufactured out of a thick section of erosion and corrosion
resistance stainless steel and fitted firmly in the rim of the wheel. A
sectional shroud ensures added rigidity. These blades are renewable and
replaceable, if need arises, on account of changing operating conditions.
BEARINGS
Precision split sleeve journal bearings incorporate Babbitt lining, and are
forced lubricated.
GLANDS
The glands are of carbon ring type, each composed of three segments
held together by an inconel spring that incorporates anti-rotation stops.
Carbon rings require no lubrication.
- 19 -

EMERGENCY VALVE
A Butterfly type valve for extreme emergency is housed in the Governor
Valve Body. This valve is made in high grade material and accurately
machined to maintain maximum seal to cut off live steam in case of
tripping of Turbine.
A stainless steel steam strainer is provided before the emergency valve
to preclude any thick impurities into entering.
OVERSPEED TRIP GOVERNOR
IBL BT-4 Turbines include an Overspeed Governor. It consists of a Ring
carried on the Turbine Shaft and operates the Emergency Valve when the
Turbine speed reaches a preset speed at 10% above the normal running
speed of the rotor.
HAND NOZZLE VALVE
One Hand operated nozzle control valve is provided to maintain
reasonable high efficiency on part load operation.
LUBRICATION
Forced lubrication is provide by a geared type oil pump which is fitted on
to the reduction Gear Box. The capacity of the pump is 90 LPM. A full duty
motor driven Oil pump is standard to flood the Bearings during start up
and shut down of the Turbine.
GEAR BOX
This non-integrated unit is housed separately and coupled with the
Turbine with metaflex type coupling. The advantage is smooth and long
life performance. This coupling with thin stainless steel flexible
Membranes gives better performance. The Gear box is a single helical
type speed reduction unit as per AGMA standard.
- 20 -

ANNEXURE - V
TURBINE TECHNICAL INFORMATION
The following parameters have been taken for the design of
the turbo alternator set.
TURBINE DETAILS
Model BT – 4 / 320
Maximum Power output 320 KW
Type Velocity compounded
Design Curtis (2 Rows)
Driven Equipment Alternator / Ind. Gen.
Turbine operating Speed 7000 RPM
TURBINE INLET CONDITIONS
Steam flow 4,000 kg/hr
Steam pressure 30.00 kg/cm² (g)
Steam temperature 350°C
Steam Rate 19.80 Kg/KW-hr
Steam Inlet Size 4”
Steam Quality Dry, Free from any Impurities
TURBINE OUTLET CONDITIONS
Steam flow 4,000 kg/hr
Steam Back pressure 3.50 kg/cm² (g)
Steam temperature 217°C ± 10°C
Steam Outlet size 8”
Power Output 202 KW
If Steam Load is 6000 Kg/hr the Power output will be 320 KW
- 21 -

ALTERNATOR (For Alternator based Sets only)
Make Leroy Somer
KW 320 KW
Voltage 415 V
Voltage Variation 5%
Frequency 50 Hz
Speed 1500 r.p.m.
Phase 3
Pf 0.8 Lagging
AVR Self Exciting
No of Poles Four
Connections Star
Insulation Class H
Overload capacity 10% overload for I hour in
every 12 hours.
Mounting Horizontal Foot Mounting
Bearing arrangement Double Sleeve Bearing
Excitation Brushless, Self Excitation
Voltage Regulation +/- 1% of Set Voltage
Voltage Setting +/-10% of Set Voltage
Coupling Geared Type
Duty Continuous
GEAR BOX
Make Triveni/Walchandnagar
Input RPM 7000
Output RPM 1500
Gear Ratio 1: 4.66
Lubrication Forced
Type Single Reduction,
parallel Shaft, Helical Type
Foot Mounted
Service Factor 1:5
Duty Continuous Input & Output
Design Standard AGMA 6011 G92
Class of accuracy DIN-415
- 22 -

MATERIAL OF CONSTRUCTION (GEAR BOX)
Gear Wheel & Pinion Shaft 820 M 17 BS: 970-PT:1-1991
(EN 354) case carburised, Hardened to 60 +/-2 RC and ground to DIN-
4/5 class of accuracy.
Gear Shaft 080 M40 – BS 1970:PT:1-92 (EN8)
Casing Cast Iron
Bearings White Metal Lined
MATERIAL OF CONSTRUCTION (TURBINE)
Casing Carbon Steel casting
Nozzles Stainless Steel ANSI 410/EN56A
Blades Stainless Steel AISI 420
Rotor Forging and Shaft 080, M40 Annealed, Hardened
and Tempered steel
Gear Wheel EN19
Gear Pinion EN 8
Labyrinth Packing Bronze
Steam Strainer Stainless Steel
Base Frame MS Fabricated
Bearings Tin Rich Babbit Lining
(White metal)
- 23 -

CONTROL PANEL
Type Free Standing type
Controller Schneider Programmable Logic Control
Initial Control Auto Synchronising Mode
Running Control Back Pressure Mode
Display on Panel
Turbine
Voltage
Frequency
Power Factor
KW
Turbine RPM
Steam Back
Pressure
Vent Valve Position
Steam Inlet Valve
Position
Display on Panel
Turbine Bearing Temperatures
Status of Elec Oil Pump
Voltage
Amperes
Electronic Synchroscope
FIELD PRESSURE GUAGES
Locations Steam Inlet pressure
Steam Exhaust pressure
Steam Nozzle Box pressure
Oil Pressure
FIELD TEMPERATURE GUAGES
Locations Steam Inlet
Steam Exhaust
Gear Box Bearing
- 24 -

BATTERY LIMITS
Inlet flange of steam turbine
Exhaust flange of steam turbine
Turbine Drains at respective points
Inlet and outlet flange for cooling water for Oil coolers
Electrical Inlet of all Controls
Protection and metering panel terminal box
Breaker panel terminal box
Turbine control panel terminal box
Power at generator terminals
EXCLUSIONS FROM TURBINE SCOPE
Steam Pipeline with inlet valve.
Exhaust Steam Piping.
Water supply for Oil Cooler.
Electrical Cabling wherever required.
Earth protection.
Thermal Insulation.
All civil works alongwith their design.
Erection and assembly at site.
Statutory permissions.
Steam Flow meter.
Flush and first fill of Oil.
- 25 -

ANNEXURE - VI
TECHNO COMMERCIAL OFFER
Supply of One No. IBL, Hybrid, Fluidised Bed Combustion
Boiler, Model Huskogen-60 capable of generating 6000
Kg/hr of Steam (From 90oC.) at the max. working pressure
455 PSI (32 Kg/cm2) at Super heater outlet with Superheated
steam temp. of 350oC. alongwith Superheater, Air Preheater
and Trexma Dust Collector.
Rs. 51,00,000/-each
(Rupees Fifty One Lac only)
Supply of One No. IBT, Captive Generation Type Steam
Turbine, Model BT- 4/320 (Alternator 320 KW) suitable for
the following duty conditions along with Alternator & Gear
Box And as per scope of supply enclosed.
Steam Inlet 30 Kg/cm2g, 350o C
Steam Pressure at Exit 3.50 Kg/cm2g
Steam Flow 4,000 Kg/hr
Estimated Power Output 230 KW
Rs. 33,00,000/-each
(Rupees Thirty Three Lacs Only)
Supervision Of Erection & Commissioning on lump sum
basis,.Lodging & Boarding for our engineer will be provided
by you on free of cost at site
Rs. 2,40,000/-Lumpsum
(Rupees Two Lacs Forty Thousand Only)
NOTE :
THE ABOVE PRICES ARE EX-WORKS VAPI.
PACKING & FORWARDING IS CHARGEABLE EXTRA @ 2%.
THIS QUOTATION IS GOVERNED BY THE STANDARD TERMS &
CONDITIONS OF OUR OFFER ENCLOSED HEREWITH.
- 26 -
MARKETING DIVISION

ANNEXURE - VII
GENERAL TERMS & CONDITIONS
PRICE :
The prices quoted are Ex-works Vapi. 2% Packing & Forwarding charges, Insurance
and Freight charges are extra. Besides sales tax, octroi, excise and bank charges are
also payable by you as applicable.
DELIVERY :
The delivery 3 – 4 months from the date of receipt of your technically and
commercially clear order accompanied by necessary advance.
We are not responsible for any delay caused by extraneous circumstances or Acts of
God beyond our control and cannot pay any damages or penalties on this account.
The equipment ordered may be dispatched in 1,2 or more lots. If required we can
undertake the dispatch of the equipment on behalf of the buyer by road transport only
to any destination given by the buyer on freight TO - PAY basis, on the clear
understanding that we will not be liable for any damages whatsoever. The freight
charges contracted by us on behalf of the buyer will be deemed as negotiated under
the buyer's authority and therefore it shall be binding on the Buyer to make full
payment.
WARRANTY :
Our products are warranted for a period of ONE YEAR from the date of dispatch,
against any manufacturing defect or faulty workmanship reported in writing during the
Warranty Period, The Warranty does not extend to consequential damages or losses.
The Warranty is NULL & VOID if repairs and/or replacements are carried out without
our consent in writing. It also does not cover bought-out items.
This warranty is not applicable if full payment with `C' form has not been given to us.
CONFIDENTIALITY :
The client shall treat all quotations, drawings, data, technical information etc. received
from Industrial Boilers Ltd., as strictly confidential an shall take all precautions
necessary to prevent the unauthorised disclosure in part or parcel of any of the above
mentioned, to any third party.
- 27 -

TERMS OF PAYMENT :
First 30% of the order value is payable as Advance with your firm order.
The balance within 15 days on submission of our Proforma Invoice, including all costs
and levies, such as price increase if any, Excise Duty, Sales Tax, Octroi and Insurance
charges `C' Form etc. is payable before the materials are dispatched from our Vapi
works.
PLACE OF JURISDICTION
In the event of any dispute arising as a result of contracting to supply against this offer
and quotation, the place of Jurisdiction will be Greater Bombay and no other place.
ARBITRATION
All disputes or differences whatsoever arising between the parties out of or relating to
the construction, meaning and operation or effect of this contract or the breach thereof
shall be settled by arbitration in accordance with the Rules of Arbitration of the Indian
Council of Arbitration and the Award made in pursuance thereof shall be binding on
both the parties.
All orders will only be accepted after the realisation after of the agreed advance which
shall not be subject to any interest under any circumstances whatsoever. We however
reserve the right to adjust such advance against any payments which might fall due
because of delay in lifting of the ordered equipment or on account of incidental
expenses incurred on buyer's behalf. An order placed with us cannot be canceled for
any reason whatsoever without our consent in writing. Any cancellation of order
without or consent will result in the forfeiture of Advance, without prejudice to our claim
for compensation and other legal remedies.
Before effecting dispatch, your Sales Tax Registration Numbers both State and
Central are to be intimated to us. It is to be clearly understood that for Inter State
dispatches Central Sales Tax Declaration Form should be handed over to us at the
time of taking delivery of the boiler. If you fail to do so, Sales Tax charges in full will be
payable to us.
- 28 -
MARKETING DIVISION

Husk based power plant 6 t 32 kg fbc with single stage turbine for finance, subsidy & project related support contact - 9861458008

More Related Content

What's hot (20)

Viewers also liked (6)

Similar to Husk based power plant 6 t 32 kg fbc with single stage turbine for finance, subsidy & project related support contact - 9861458008 (20)

More from Radha Krishna Sahoo (20)

Husk based power plant 6 t 32 kg fbc with single stage turbine for finance, subsidy & project related support contact - 9861458008