8086 microprocessor instruction set by Er. Swapnil Kaware

Instruction Set of 8086 Microprocessor

Presented By,
Er. Swapnil Kaware,
B.E. (Electronics),
svkaware@yahoo.co.in

Instruction set basics
• Instruction:- An instruction is a binary pattern designed
inside a microprocessor to perform a specific function.

• Opcode:- It stands for operational code. It specifies the
type of operation to be performed by CPU. It is the first
field in the machine language instruction format.
• E.g. 08 is the opcode for instruction “MOV X,Y”.

• Operand:- We can also say it as data on which operation
should act. operands may be register values or memory
values. The CPU executes the instructions using
information present in this field. It may be 8-bit data or 16-
bit data.
Microprocessor Notes By Er. Swapnil
Kaware (svkaware@yahoo.co.in)

Instruction set basics

• Assembler:- it converts the instruction into sequence of
binary bits, so that this bits can be read by the
processor.

• Mnemonics:- these are the symbolic codes for either
instructions or commands to perform a particular
function.
• E.g. MOV, ADD, SUB etc.


Instruction Formats
• In 8086 microprocessor there are following six types of
instruction formats.

(1). 1-Byte instruction,
(2). Register to register,
(3). Register to/from memory with no displacement,
(4). Register to/from memory with displacement,
(5). Immediate operand to register,
(6). Immediate operand to memory with 16-Bit
displacement. Microprocessor Notes By Er. Swapnil

(1). 1-Byte instruction

• The instruction is 1-byte long in size.

• It May contain implied data or register operands
(data).

• The least significant three bits of opcode are
used for specifying register operand. Otherwise
all the 8-bits creates an opcode.

(2). Register to Memory
• First byte of code denotes opcode & width of operand.
• Second byte denotes register operands & R/M field.
• ‘REG’ field denotes type of register used.
• ‘R/M’ field denotes register or memory location used.
• If ‘W’ field is ‘0’ then operand is of 8-bits, & If ‘W’ field
is ‘1’ then operand is of 16-bits.

D7 D1 D0 D7 D6 D5 D3 D2 D0
OPCODE W 11 REG R/M


(3). Register to/from memory with no
Displacement
• First byte of code denotes opcode & width of operand.
• Second byte denotes mod,register operands & R/M
field.
• ‘MOD’ field denotes type of addressing mode used.

D7 D1 D0 D7 D6 D5 D3 D2 D0
OPCODE W MOD REG R/M

(4). Register to/from memory with
Displacement
• First byte of code denotes opcode.
• Second byte denotes register mod,register operands &
R/M field.
• Third byte denotes lower byte of displacement.
• fourth byte denotes higher byte of displacement.

D7 D0 D7 D6 D5 D3 D2 D0 D7 D0 D7 D0
OPCODE MOD REG R/M Lower Byte of Higher Byte of
displacement displacement

(5). Immediate operand to register
• Second byte denotes opcode,R/M field.
• Third byte denotes lower byte of data.
• fourth byte denotes higher byte of data.

D7 D0 D7 D6 D5 D3 D2 D0 D7 D0 D7 D0
OPCODE 11 REG R/M Lower Byte of Higher Byte of data
data

(6). Immediate operand to memory with
16-bit displacement
• The instruction is 5 or 6-byte long in size.
• Second byte denotes register mod,opcode & R/M field.
• Third byte denotes lower byte of displacement.

D7 D0 D7 D6 D5 D3 D2 D0 D7 D0
OPCODE MOD OPCODE R/M Lower Byte of
displacement

D7 D0 D7 D0 D7 D0
Higher Byte of Lower Byte of Higher Byte of
displacement data data

Assignment of codes to Registers


Addressing modes & corresponding
MOD,REG & R/M field


Addressing Modes of 8086
Microprocessor
• (1). Immediate,
• (2). Direct,
• (3). Register,
• (4). Register Indirect,
• (5). Indexed,
• (6). Register Relative,
• (7). Based Indexed,
• (8). Relative Based Indexed.
• (9). Intrasegment Direct Mode.
• (10). Intrasegment Indirect Mode.
• (11). Intrasegment Direct.
• (12). Intrasegment Indirect. Microprocessor Notes By Er. Swapnil

Types of instruction set of 8086
microprocessor
(1). Data Copy/Transfer instructions.

(2). Arithemetic & Logical instructions.

(3). Branch instructions.

(4). Loop instructions.

(5). Machine Control instructions.

(6). Flag Manipulation instructions.

(7). Shift & Rotate instructions.

(8). String instructions. Microprocessor Notes By Er. Swapnil

(1). Data copy/transfer instructions.
• (1). MOV Destination, Source;

• There will be transfer of data from source to destination.
• Source can be register, memory location or immediate
data.
• Destination can be register or memory operand.
• Both Source and Destination cannot be memory location
or segment registers at the same time.
• E.g.
• (1). MOV CX, 037A H;
• (2). MOV AL, BL;
• (3). MOV BX, [0301 H]; Microprocessor Notes By Er. Swapnil

BEFORE EXECUTION AFTER EXECUTION

AX 2000H MOV BX,AX; BX 2000H

AH AL AH AL
BH BL BH BL
CH CL
MOV CL,M; CH CL 40
DH DL 40 DH DL 40


Stack Pointer
• It is a 16-bit register, contains the address of the data
item currently on top of the stack.

• Stack operation includes pushing (providing) data on
to the stack and popping (taking)data from the stack.

• Pushing operation decrements stack pointer and
Popping operation increments stack pointer. i.e.
there is a last in first out (LIFO) operation.


• (2). Push Source;

• Source can be register, segment register or memory.
• This instruction pushes the contents of specified source
on to the stack.
• In this stack pointer is decremented by 2.
• The higher byte data is pushed first (SP-1).
• Then lower byte data is pushed (SP-2).

• E.g.:
• (1). PUSH AX;
• (2). PUSH DS;
• (3). PUSH [5000H]; Microprocessor Notes By Er. Swapnil

INITIAL POSITION

(1) STACK POINTER

DECREMENTS SP & STORES HIGHER BYTE

(2) STACK POINTER HIGHER BYTE

DECREMENTS SP & STORES LOWER BYTE

(3) STACK POINTER LOWER BYTE
HIGHER BYTE


BEFORE EXECUTION

SP 2002H
2000H
BH BL
2001H
CH 10 CL 50
DH DL 2002H

PUSH CX
AFTER EXECUTION
2000H 50
SP 2000H
BH BL
2001H 10
CH 10 CL 50

DH DL 2002H

• (3). POP Destination;

• Destination can be register, segment register or memory.
• This instruction pops (takes) the contents of specified
destination.
• In this stack pointer is incremented by 2.
• The lower byte data is popped first (SP+1).
• Then higher byte data is popped (SP+2).

• E.g.
• (1). POP AX;
• (2). POP DS;
• (3). POP [5000H]; Microprocessor Notes By Er. Swapnil

INITIAL POSITION AND READS LOWER BYTE
(1) STACK POINTER LOWER BYTE

INCREMENTS SP & READS HIGHER BYTE
LOWER BYTE
(2) STACK POINTER HIGHER BYTE

INCREMENTS SP

LOWER BYTE
HIGHER BYTE
(3) STACK POINTER

BEFORE EXECUTION

2000H 30
SP 2000H
2001H 50
BH BL
2002H

POP BX
AFTER EXECUTION
2000H 30
SP 2002H 2001H 50
BH 50 BL 30 2002H

• (4). XCHG Destination, source;
• This instruction exchanges contents of Source with
destination.

• It cannot exchange two memory locations directly.

•The contents of AL are exchanged with BL.

•The contents of AH are exchanged with BH.

•E.g.
(1). XCHG BX, AX;
(2). XCHG [5000H],AX;


AH 20 AL 40 AH 70 AL 80

BH 70 BL 80 BH 20 BL 40

XCHG AX,BX;

• (5). IN AL/AX, 8-bit/16-bit port address

• It reads from the specified port address.
• It copies data to accumulator from a port with 8-bit
or 16-bit address.
• DX is the only register is allowed to carry port
address.
• E.g.
(1). IN AL, 80H;
(2). IN AX,DX; //DX contains address of 16-bit port.

BEFORE EXECUTION

PORT 80H 10 AL

IN AL,80H;

AFTER EXECUTION

PORT 80H 10 AL 10

• (6). OUT 8-bit/16-bit port address, AL/AX;

• It writes to the specified port address.
• It copies contents of accumulator to the port with 8-
bit or 16-bit address.
• DX is the only register is allowed to carry port
address.
• E.g.
(1). OUT 80H,AL;
(2). OUT DX,AX; //DX contains address of 16-bit port.

BEFORE EXECUTION

PORT 50H 10 AL 40

OUT 50H,AL;

AFTER EXECUTION

PORT 50H 40 AL 40

• (7). XLAT;

• Also known as translate instruction.
• It is used to find out codes in case of code conversion.
• i.e. it translates code of the key pressed to the
corresponding 7-segment code.
• After execution this instruction contents of AL register
always gets replaced.
• E.g. XLAT;

• (8). LEA 16-bit register (source), address (dest.);

• LEA Also known as Load Effective Address (LEA).
• It loads effective address formed by the
destination into the source register.

• E.g.
(1). LEA BX,Address;
(2). LEA SI,Address[BX];

• (9). LDS 16-bit register (source), address (dest.);
• (10). LES 16-bit register (source), address (dest.);

• LDS Also known as Load Data Segment (LDS).
• LES Also known as Load Extra Segment (LES).
• It loads the contents of DS (Data Segment) or ES (Extra
Segment) & contents of the destination to the contents of
source register.

• E.g.
(1). LDS BX,5000H;
(2). LES BX,5000H;

(1). LDS BX,5000H;
(2). LES BX,5000H;

15 0 7 0
BX 20 10 10 5000H
20
5001H
30 5002H
DS/ES 40 30
40 5003H


• (11). LAHF:- This instruction loads the AH register
from the contents of lower byte of the flag register.
• This command is used to observe the status of the
all conditional flags of flag register.
• E.g. LAHF;

• (12). SAHF:- This instruction sets or resets all
conditional flags of flag register with respect to the
corresponding bit positions.
• If bit position in AH is 1 then related flag is set
otherwise flag will be reset.
• E.g. SAHF; Microprocessor Notes By Er. Swapnil

• (13). PUSH F:- This instruction decrements the stack
pointer by 2.
• It copies contents of flag register to the memory
location pointed by stack pointer.
• E.g. PUSH F;

• (14). POP F:- This instruction increments the stack
pointer by 2.
• It copies contents of memory location pointed by
stack pointer to the flag register.
• E.g. POP F;

(2). Arithematic Instructions
• These instructions perform the operations
like:

• Addition,
• Subtraction,
• Increment,
• Decrement.


• (1). ADD destination, source;

• This instruction adds the contents of source operand with
the contents of destination operand.
• The source may be immediate data, memory location or
register.
• The destination may be memory location or register.
• The result is stored in destination operand.
• AX is the default destination register.

• E.g. (1). ADD AX,2020H;
(2). ADD AX,BX;Microprocessor Notes By Er. Swapnil

AH 10 AL 10 ADD AX,2020H AH 30 AL 30

1010
+2020
3030


AH 10 AL 10 AH 30 AL 30
BH 20 BL 20
ADD AX,BX BH 20 BL 20

2050

• (2). ADC destination, source
• This instruction adds the contents of source operand with
the contents of destination operand with carry flag bit.
register.
• The result is stored in destination operand.
• AX is the default destination register.

• E.g. (1). ADC AX,2020H;
(2). ADC AX,BX; Microprocessor Notes By Er. Swapnil

ADC AX,2020H
CY 1
AH 10 AL 10 AH 30 AL 31
1010
+2020
3030+1=3031
CY 1
AH 10 AL 10 AH 30 AL 31
BH 20 BL 20
ADC AX,BX BH 20 BL 20

2050

• (3). INC source

• This instruction increases the contents of source
operand by 1.
• The source may be memory location or register.
• The source can not be immediate data.
• The result is stored in the same place.

• E.g. (1). INC AX;
(2). INC [5000H];


AH 10 AL 10 INC AX AH 10 AL 11


5000H 1010 INC [5000H] 5000H 1011


• (4). DEC source;

• This instruction decreases the contents of source
operand by 1.
• The source may be memory location or register.
• The source can not be immediate data.
• The result is stored in the same place.

• E.g. (1). DEC AX;
(2). DEC [5000H];


AH 10 AL 10 DEC AX AH 10 AL 09


5000H 1010 DEC [5000H] 5000H 1009


• (5). SUB destination, source;
• This instruction subtracts the contents of source operand
from contents of destination.
register.
• The result is stored in the destination place.

• E.g. (1). SUB AX,1000H;
(2). SUB AX,BX;


AH 20 AL 00 SUB AX,1000H AH 10 AL 00

2000
-1000
=1000


AH 20 AL 00 AH 10 AL 00
BH 10 BL 00 SUB AX,BX BH 10 BL 00

• (6). SBB destination, source;
• Also known as Subtract with Borrow.
• This instruction subtracts the contents of source operand
& borrow from contents of destination operand.
register.
• The result is stored in the destination place.

• E.g. (1). SBB AX,1000H;
(2). SBB AX,BX; Microprocessor Notes By Er. Swapnil

SBB AX,1000H
B 1
AH 20 AL 20 AH 10 AL 19
2020
- 1000
1020-1=1019
B 1
AH 20 AL 20 AH 10 AL 19
BH 10 BL 10
SBB AX,BX BH 10 BL 10

2050

• (7). CMP destination, source
• Also known as Compare.
• This instruction compares the contents of source operand
with the contents of destination operands.
register.
• Then resulting carry & zero flag will be set or reset.

• E.g. (1). CMP AX,1000H;
(2). CMP AX,BX;

D=S: CY=0,Z=1
BEFORE EXECUTION D>S: CY=0,Z=0
D<S: CY=1,Z=0 AFTER EXECUTION

AH 10 AL 00
CMP AX,BX CY 0 Z 1
BH 10 BL 00

AH 10 AL 00
CMP AX,BX CY 0 Z 0
BH 00 BL 10

AH 10 AL 00
CMP AX,BXH CY 1 Z 0
BH 20 BL 00


• (8). AAA
• Also known as ASCII Adjust After Addition.
• This instruction is executed after ADD instruction.
(1). IF lower bits of AL<=09 then,
• Higher bits of AL should loaded with zeroes.
• There should be no change in lower bits of AL.
• AH also must be cleared (AH=0000 0000).
(2). IF lower bits of AL>09 then,
• Bits of AL must be incremented by 06 (i.e. AL+0110).
• Bits of AH must be incremented by 01 (i.e. AH+0001).
• Then higher bits of AL should be loaded with 0000.

• E.g. (1). AAA;

(1). FOR AL<=09H
AL 6 7 BEFORE EXECUTION
Hb Lb
AL 0 7 AFTER EXECUTION
Hb Lb
Hb=Higher bits,
Lb=Lower bits.
(1). FOR AL>09H
AL 6 A BEFORE EXECUTION
Hb Lb
(A)1010 +(06)0110=0001 0000
HB LB
Hb Lb

• (9). AAS
• Also known as ASCII Adjust After Subtraction.
• This instruction is executed after SUB instruction.
(1). IF lower bits of AL<=09 then,
• Higher bits of AL should loaded with zeroes.
• There should be no change in lower bits of AL.
• AH also must be cleared (AH=0000 0000).
(2). IF lower bits of AL>09 then,
• Bits of AL must be decremented by 06 (i.e. AL-0110).
• Bits of AH must be decremented by 01 (i.e. AH-0001).
• Then higher bits of AL should be loaded with 0000.

• E.g. (1). AAS;

(1). FOR AL<=09H
AL 6 7 BEFORE EXECUTION
Hb Lb
Hb Lb
Hb=Higher bits,
Lb=Lower bits.
(1). FOR AL>09H
AL 6 A BEFORE EXECUTION
Hb Lb
(A)1010 -(06)0110=0000 0100
Hb Lb
Hb Lb

• (10). AAM
• Also known as ASCII Adjust After Multiplication.
• This instruction is executed after MUL instruction.
• Then AH=AL/10 & AL=Remainder.

• E.g. MOV AL,04 // AL=04
• MOV BL,09 // BL=09
• MUL BL // 04*09=36 (i.e. BL*AL)
• AAM // AH=03 & AL=06

• E.g. (1). AAM;

• (11). AAD;
• Also known as ASCII Adjust before Division.
• Then AL=AH*10 +AL & AH=0.

• E.g. MOV AX, 0105 // AH=01, AL=05
• AAD // AL=15 (i.e.0FH) & AH=00

• E.g. (1). AAD;


• (12). DAA;
• Decimal Adjust Accumulator.
• IF lower bits of AL>09.
• Then AL=AL+06.

• E.g. MOV AL,53H //AL=53H
• MOV CL,29H //CL=29H
• ADD AL,CL // AL=7CH (i.e. 12=C) & C>9.
• DAA // AL=7C+06=82H. (i.e. 0111 1100 + 0000 0110)=1000 0010
• 7 C + 0 6 = 8 2

• E.g. (1). DAA;

• (13). DAS
• Decimal Adjust after Subtraction.
• IF lower bits of AL>09.
• Then AL=AL-06.

• E.g. MOV AL,30H // AL=30H
• MOV CL,20H // CL=20H
• SUB AL,CL // AL=0AH (i.e. A=10) & C=10>9.
• DAS // AL=0A-06=04H. (i.e. 0000 1010 - 0000 0110)=0000 0100
• 0 A - 0 6 = 0 4

• E.g. (1). DAS;

• (14). MUL operand
• Unsigned Multiplication.
• Operand contents are positively signed.
• Operand may be general purpose register or memory location.
• If operand is of 8-bit then multiply it with contents of AL.
• If operand is of 16-bit then multiply it with contents of AX.
• Result is stored in accumulator (AX).

• E.g. (1). MUL BH // AX= AL*BH; // (+3) * (+4) = +12.

• (2). MUL CX // AX=AX*CX;

• (15). IMUL operand
• Signed Multiplication.
• Operand contents are negatively signed.
• Operand may be general purpose register, memory location or index
register.
• If operand is of 8-bit then multiply it with contents of AL.
• If operand is of 16-bit then multiply it with contents of AX.
• Result is stored in accumulator (AX).

• E.g. (1). IMUL BH // AX= AL*BH; // (-3) * (-4) = 12.
• (2). IMUL CX // AX=AX*CX;

• (16). DIV operand
• Unsigned Division.
• Operand may be register or memory.
• Operand contents are positively signed.
• AL=AX/Operand (8-bit/16-bit) & AH=Remainder.

• E.g. MOV AX, 0203 // AX=0203
• MOV BL, 04 // BL=04
• IDIV BL // AL=0203/04=50 (i.e. AL=50 & AH=03)

• (17). IDIV operand
• Signed Division.
• Operand may be register or memory.
• Operand contents are negatively signed.
• AL=AX/Operand (8-bit/16-bit) & AH=Remainder.

• E.g. MOV AX, -0203 // AX=-0203
• MOV BL, 04 // BL=04
• DIV BL // AL=-0203/04=-50 (i.e. AL=-50 & AH=03)

(3). Logical Instructions
• (1). AND destination,source
• Destination operand may be register, memory location.
• Source operand may be register, immediate data or
memory location.
• Result is stored in destination operand.

• E.g. MOV AX, 3F0FH // AX=3F0FH
• MOV BX, 0008H // BX=0008H
AND AX,BX // AX=0008H

• Follow the rules as given below:-
(1). 1 AND 1 = 1
(2). 1 AND 0 = 0
(3). 0 AND 1 = 0
(4). 0 AND 0 = 0

• 3F0FH= 0011 1111 0000 1111
• 0008H=0000 0000 0000 1000
• 0000 0000 0000 1000 = 0008H

• (2). OR destination,source
• Destination operand may be register, memory location.
• Source operand may be register, immediate data or
memory location.
• Result is stored in destination operand.

• E.g. MOV AX, 3F0FH // AX=3F0FH
• MOV BX, 0098H // BX=0098H
OR AX,BX // AX=3F9FH

(1). 1 OR 1 = 1
(2). 1 OR 0 = 1
(3). 0 OR 1 = 1
(4). 0 OR 0 = 0

• 3F0FH= 0011 1111 0000 1111
• 0098H=0000 0000 1001 1000
• 0011 1111 1001 1111 = 3F9FH

• (3). NOT operand;
• Operand may be register, memory location.
• This instruction inverts (complements) the contents of
given operand.
• Result is stored in Accumulator (AX).

• E.g. MOV AX, 0200FH // AX=200FH
• NOT AX // AX=DFF0H


(1). 1 NOT = 0
(2). 0 NOT = 1

• 200FH= 0010 0000 0000 1111
• 1101 1111 1111 0000 = DFF0H


• (4). TEST destination,source
• Both operands may be register, memory location or immediate
data.
• This instruction performs bit by bit logical AND operation for
flags only (i.e. only flags will be affected).
• If the corresponding 0th bit of result contains ‘1’ then result will
be non-zero & zero flag will be cleared/reset (i.e. ZF=0).
• If the corresponding 0th bit of result contains ‘0’ then result will
be zero & zero flag will be set (i.e. ZF=1)..

• E.g. (1). TEST AX,BX
• (2). TEST [0500],06H

• (5). RCR
• Also known as Rotate Right through Carry.
• Each binary bit of the operand is rotated towards right
by one position through Carry flag.
• Least Significant Bit (LSB) i.e. B0 is placed in the Carry
flag.
• Then carry flag bit is placed in the Most Significant Bit
(MSB) position B15.

BEFORE EXECUTION

B B B B B B B B B B B B B B B B CF
1 1 0 1 0 0 1 0 0 0 0 1 0 0 0 1 0
15 7 0

AFTER EXECUTION

B B B B B B B B B B B B B B B B CF
0 1 1 0 1 0 0 1 0 0 0 0 1 0 0 0 1
15 7 0


• (6). RCL
• Also known as Rotate Left through Carry.
• Each binary bit of the operand is rotated towards left
by one position through Carry flag.
• Least Significant Bit (LSB) of operand i.e. B0 is placed in
the B1.
• Then Most Significant Bit (MSB) of operand is placed
in carry flag bit.

BEFORE EXECUTION

CF B B B B B B B B B B B B B B B B
0 1 0 0 1 0 0 1 0 0 0 0 1 0 0 0 1

AFTER EXECUTION

CF B B B B B B B B B B B B B B B B
1 0 0 1 0 0 1 0 0 0 0 1 0 0 0 1 0


(4). String Manipulation Instructions
• (1). REP
• Also known as Repeat instruction prefix.
• This instruction executed repeatedly until the ‘CX’ register
becomes zero.
• When ‘CX’ becomes zero then program control passes to
next instruction.
• There are following sub types of ‘REP’ instruction,
• (i). REPE:- REPeat instruction while Equal.
• (ii). REPZ:- REPeat instruction while Zero.
• (iii). REPNE:- REPeat instruction while Not Equal.
• (iv). REPNZ:- REPeat instruction while Not Zero.

(4). String Manipulation Instructions
• (2). CMPS
• Also known as Compare String Byte or String Word.
• The length of the string must be stored in register CX.
• If both the byte or word are equal then zero flag will
be set (i.e. ZF=1) otherwise it will be reset (i.e. ZF=0).
• When zero flag will be set then ‘CX’=0.
• There are following sub types,
• (i). CMPSB:- Compare String Byte.
• (ii). CMPSW:- Compare String Word.

(5). Branching Instructions
• (1). CALL
• Also known as unconditional call.
• Under unconditional call, the execution control is
transferred to the specified location independent of
any status or condition.
• This instruction is used to call subroutine from a main
program.
• There are following sub types,
• (i). NEAR CALL:- It pushes only IP into the stack.
• (ii). FAR CALL:- It pushes IP & CS into the stack.

(5). Branching Instructions
• (2). JMP
• Also known as unconditional jump.
• Under unconditional jump, the execution control is transferred to the
specified location using 8-bit or 16-bit displacement.
• There are following three formats of jump instruction,
• (i). JMP 8-bit Displacement
• (ii). JMP 16-bit Displacement (LB) 8-bit Displacement (UB)

• (iii). JMP IP (LB) IP (UB) CS (LB) CS (UB)


(6). Flag Manipulation Instructions
• (1). CMC
• Also known as Complement Carry Flag.
• It inverts contents of carry flag.
• if CF = 1 then CF will be = 0.
• if CF = 0 then CF will be = 1.

• E.g. CMC


• (2). STC
• Also known as Set Carry Flag.
• It makes carry flag in set condition.
• After execution CF = 1.

• E.g. STC


• (3). CLI
• Also known as Clear Interrupt Flag.
• It makes interrupt flag in reset condition.
• After execution IF = 0.

• E.g. CLI


• (4). CLD
• Also known as Clear Direction Flag.
• It makes direction flag in reset condition.
• After execution DF = 0.

• E.g. CLD


(7). Machine Control Instructions
• (1). HLT
• Also known as Halt
• It makes the processor to be in stable (do nothing)
condition.

• E.g. HLT


(7). Machine Control Instructions
• (2). NOP
• Also known as No Operation.
• It tells about further there will be no operation to be
performed.

• E.g. NOP


“ End of
Instruction Set
Session”……
For more information please visit the link www.slideshare.net/svkaware

8086 microprocessor instruction set by Er. Swapnil Kaware

More Related Content

What's hot (20)

Viewers also liked (15)

Similar to 8086 microprocessor instruction set by Er. Swapnil Kaware (20)

More from Prof. Swapnil V. Kaware (20)

Recently uploaded (20)

8086 microprocessor instruction set by Er. Swapnil Kaware