A Microcontroller Framework For PC Based Electrical Appliance Control System

IJSRSET151384 | Received: 07 July 2015 | Accepted: 18 September 2015 | September-October 2015 [(1)5: 60-65]
© 2015 IJSRSET | Volume 1 | Issue 5 | Print ISSN : 2395-1990 | Online ISSN : 2394-4099
Themed Section: Engineering and Technology
60
A Microcontroller Framework for PC Based Electrical Appliance
Control System
Ganiyu Adedayo. Ajenikoko, Timothy O. Araoye, Akinniyi T. Akintayo, Dare E. Oyekunle, Isiah I. Olugbemiga
Department of Electronic & Electrical Engineering, Ladoke Akintola University of Technology, P.M.B. 4000, Ogbomoso, Nigeria
ABSTRACT
Personal computers are increasingly becoming the platform of choice to design and implement control algorithms
because it is simple to write, modify and update software programs that implement control algorithms. In this paper,
the personal computer is used to control the electrical appliances which includes turning high power alternating
current (AC) loads such as lights, fans, heaters etc ON or OFF. To successfully integrate the interface box with the
machine (laptop), an interface device is used within the PC that can perform the necessary tasks. The interface box
can be controlled by the computer by connecting to the USB port and developed a program in C-sharp(C#)
programming language. The program will demonstrate the basic idea of how to control devices and monitor events.
With the program, the computer can turn electric devices ON/OFF while disregarding the manual control system.
Moreover, the people who are physically disabled in homes and work places are able to control the home appliances
by interacting with the interface of the developed appliance. It is a necessity to employ the service of Home
Appliances Control as it is more effective, efficient and stress-free.
Keywords: Personal Computers, Home Control Appliance, Distribution Fuse Board (DFB), Graphical User
Interface (GUI), Interface Box, Internal Module, Enumeration, Local Area Network (LAN).
I. INTRODUCTION
A Personal computer (PC) based home control appliance
is the use of control systems at homes, in the offices and
in industries to reduce human efforts. Home control
appliances have greatly decreased the need for human
sensory and mental equipments and play an important
role in the world economy and in daily experience. It is
more efficient and stress-free (Coyle et al 2007).
Home and office appliances, including television, VCRs,
stereo equipment, refrigerators,, washing machines,
thermostat, light switches, telephones, copiers and
factory equipment, have embedded computers and often
come with remote controls. However, the trend has been
that as appliances get more computerized with more
features, their user interfaces get harder to use (Dickey
et al 2012).
PCs are commonly used with better input-output
capability than the average home appliance, such as
high-resolution screens, text-entry technologies and
speech capability. PC.s are likely to maintain this
advantage over appliances, because improved hardware
is a key differentiator between PC and is often marketed
as an incentive to upgrade to a new PC. All PC has the
ability to communicate over the Local Area Network
(LAN) and most have built-in short range
communication capabilities, such as Bluetooth, that
could allow them to communicate with and control
appliance in their surrounding environment. PC laptops
are also personal devices, which allow them to provide
interface that are personalized (Koyuncu 1995, Nunes
and Delgado 2000, Sriskanthan and Tan 2002).
1.1 The brain of the system
The brain of the system is actually a small computer
whose job is to close the switch that activates the
switches that powers sensing devices when ON or OFF.
Home based PC differs mainly in Distribution Fuse
Board (DFB) and how various home appliances are
wired in to the brain. The brain and the DFB features

International Journal of Scientific Research in Science, Engineering and Technology (ijsrset.com)
61
may be wired into the control room, but they usually
have a back-up power source as well. The architecture of
the PC home based appliances control system is shown
in Figure 1.
The system consists of two units (Swamy et al 2002,
Nichols and Myers, 2006):
1. Control unit: The control unit is based on the
use of standard personal computer with
Graphical User Interface (GUI) software to
control the electrical appliances.
2. Interface unit: The interface unit is for
interfacing the high power loads with the control
unit.
Figure 1: Architecture of the PC home based appliances
control
1.2. Hardware Design of the Interface Box
The design of the interface box that is used to connect
high power load to the computer is discussed here.
Internal module
The internal circuitry of the interface box can be divided
into three main categories namely: relay driver circuit,
relay and +6 V DC power supply.
Computer Interfacing
The Universal Bus (USB) is one of the most common
interfaces used in electronic consumer product today,
including PCS, cameras, GPS devices, MP3 players,
modems , printers and scanners, to mention a few. These
are data lines, control lines and status lines. The USB is
a high-speed serial interface that can provide power to
device connected to it(Kim et al 2010, Lin and Brogerg
2002, Neng-Shiiang et al, 2002). A USB bus supports up
to 127 devices (limited by the 7-bit address field noting
that address 0 is not used as it has a special purpose)
connected through a four-wire serial cable of three to
five meters long. Many USB devices can be connected
to the same bus with hubs, which can have 4, 8, or even
16 ports. A device can be plugged into a hub which is
plugged into another hub and so on. The maximum
number of tiers permitted is six. According to the
specification, the maximum distance of a device from its
host is about thirty meters, accomplished by using five
hubs. For longer-distance bus communications, other
methods such as use of Ethernet are recommended.
The USB bus specification comes in two versions: the
version USB 1.1, supporting 11Mbps, while the version,
USB 2.0 supports up to 480Mbps. The USB
specification defines three data speeds (Al-Ali and Al-
Rousan 2004, Kobatake et al 1989).:
i. Low speed ---- 1.5Mb/sec.
ii. Full speed------ 12Mb/sec.
iii. High speed ----- 480Mb/sec.
The maximum power available to an external device is
limited to about 100mA at 5.0V. USB is a four- wire
interface implemented using a four-core shielded cable.
Two types of connectors are specified and used, Table 1
shows typical USB connectors and Table 2 shows the
pin-out of the USB connectors. The signal wire colors
are specified. The specification also defines a mini-B
connector, mainly used in smaller portable electronic
devices such as cameras and other handheld devices.
This connector has a fifth pin called ID, though this pin
is not used. The pin assignment and wire colors of a
mini-B connector are given. Two of the pins, Data + and
Data -, form a twisted pair and differential data signals
and some single- ended data states.
Table 1: USB pin configuration
Pin no Name Color
1 +5.0V Red
2 Data- White
3 Data+ Green
4 Ground Black
Table 2: USB pin assignment
Pin no Name Color
1 +5.0V Red
2 -Data White
3 +Data Green
4 Not Used -------
5 Ground Black

62
Enumeration
When a device is plugged into a USB bus, it becomes
known to the host through a process called enumeration.
The steps of enumeration are (Anamal and
Kamruzzaman 2006, Casimiro et al 2004):
i. When a device is plugged in, the host becomes
aware of it because one of the data line voltages
(Dp or D) becomes logic high.
ii. The host sends a USB reset signal to the device
to place the device in a known state. The reset
device responds to address 0.
iii. The host sends a request on address 0 to the
device to find out its maximum packet size
using a Get Descriptor command.
iv. The device responds by sending a small portion
of the device descriptor.
v. The host sends a USB reset again.
vi. The host assigns a unique address to the device
and sends a Set Address request to the device.
II. METHODS AND MATERIAL
The design demonstrates a system that allows one to
control home appliance and turns ON or OFF any
appliance that is connected to a computer. The
appliances are connected to the computer via a
microcontroller. The power supply for each appliance is
through an electromechanical relay. A number of relays
are used depending on the number of appliances to be
controlled. All the relays are controlled by a
microcontroller. The microcontroller is connected to the
computer via a USB to RS232 Converter. The diagram
below in Figure 2 shows the block diagram of the
system.
Figure.2: Block Diagram of the designed system
2.1. Approach to Development of the Framework
The basis of the hardware design is mainly the
PICI6F876A microcontroller using micro C pro
compiler. Two circuit diagrams were developed. These
are:
i. Power supply regulation circuit
ii. Main component circuit
2.1.1 Power Supply Regulation Circuit
The a.c. power supply to the circuit has to be regulated
to a reasonable amount for the workability and durability
of the circuit components. The power supply regulation
circuit is shown in Figure 3.The power supply regulation
process is accomplished by following the four stages
listed below:
i Transformer
ii Rectification
iii Filtering
iv Voltage regulation
Transformer
The a.c. supply gives out 220V or above and the supply
is stepped down by the transformer to a reasonable
amount of 12V which is needed for the operation of the
circuit.
Rectification
There is the need for the conversion of the a.c. voltage to
d.c. voltage. Diodes help in this conversion process.
However, in the conversion process the voltage drop
across the diode which is greater than 1V is added to the
already stepped down 12V and making the total voltage
in the rectification to be 13V or greater.
Filtering
The capacitor removes or filters the ripples generated
and produced alongside the rectification process.
Voltage Regulation
Voltage regulator are devices that produce constant d.c.
voltage regardless of the variation in the input load. Two
voltage regulators are used in this stage. These are:
i LM7812 voltage regulator
ii LM7805 voltage regulator

63
Figure 3: Power supply regulation circuit
2.1.2 Main component Circuit Analysis
The USB cable is fed to the DB-9 which is actually a
serial connector. This serial connector allows for bi-
directional communication between the system and the
hardware (I.e it sends signals to and receives signals
from the PC.) The DB-9 though stabbed at pin 5 is fed to
the MAX232 which is the level converter.
Figure 4: Main component circuit analysis
The level converter does and undoes the signal by
generating a total of 12V supply and reversing it to 5V
d.c. supply. It is fed to the PIC16F876A microcontroller
from the level converter. A d.c. voltage of 5V is needed
for the operation of the PIC. It processes the signal
according to instruction. Attached to the microcontroller
is the clock pulse which generates clock frequency for
the microcontroller. The clock pulse is the heart of the
microcontroller as the microcontroller fails to work in
the absence of those clock frequencies.
A d.c voltage of 12V is needed for the operation of the
relay. A total of seven relays were used as each relay
demands a transistor for amplification. One kilo ohms
resistor was also introduced to restrict and oppose the
amount of current that flows to the base of the transistor.
The signal is finally executed as the relay opens up to
socket to be controlled. The main component circuit
analysis is shown in Figure 4.
2.2 Software Interface
The layout of the software used for controlling various
home appliances is shown in Figure 5 .As an
experimental basis, the following layouts are present in
the software interface:
i Seven rooms with their corresponding ON and
OFF buttons.
ii Selection of communication port
iii All ON button
iv All OFF button
v ROM status interface which consists of check
status and clear report.
At first, a port number is set in the Selection Com Port
field of the layout to activate connection between
computer and microcontroller. If the connection is
successful, then it is possible to control the appliances
from the computer. Each device can be controlled either
as an ON or OFF mode by pressing ON or OFF button
on the layout. The “check status” reports the state (ON
or OFF) of the electrical control l appliances by
displaying information that the appliance is ON. The
clear report command gets rid of the information
reported in the room status interface. Although, only
seven rooms have been shown, but any number of
devices can be controlled from a computer with a slight
modification in the designed system. The software
layout interface is shown in Figure 5.

64
Figure 5: Software Interface layout
2.3. PIC-GUI Communication
The hardware uses RS232 converter to communicate
with the software. Contained in the RS232 converter is
the RS232 library which has RX (receiver) and TX
(transmitter) for both transmissions and reception of
signals. The software in the other end has serial port
library which is one of the controls in c-sharp library. It
is thus programmed to enable transmission and reception
of signals.
Once the “COM port” is selected in the software, a link
is opened up for communication between the hardware
and the software which will last for microseconds.
Through, there is a propagation delay which allows for
execution of commands or instruction before
transmission of another signal. For every button clicked
in the graphical user interface. The serial port library
uses its TX to transmit the signal to the hardware. The
signal is received by the hardware via its RX, processed
according to instruction and opens up the relay of the
required unit and therefore switches ON its socket
The hardware on the reverse end uses its TX to transmit
signal (indicating the reception of the sent signal by the
program) to the software. The software receives the
signal via its RX and thus acknowledges it by displaying
the message about the state (ON or OFF) of the required
unit on the room status interface. The flow chart
showing PIC-GUI communication is shown in Figure 6.
Figure 6: Flow chart showing PIC- GUI communication
Choice of Programming Language
The application program used in this research paper is
C-Sharp.
Reasons for the choice of programming language
i It is very convenient to use (i.e it has improved
Graphical User Interface)
ii It has controls that one can pick and drop.
iii It is easier to communicate with the PIC
microcontroller.
III. RESULTS AND DISCUSSION
Description of Flow Process
Initially, all the switches are in the state. When the ON
button is clicked in the software interface to turn ON the
desired device, the software converts the ON command
into hex code, then sends the value to USB port address.
It sends logic 1 (3.5-5V) to the microcontroller through
RS232 converter. The microcontroller then sends a 1 to
the transistor. It will activate the transistor used to
energise the relay. There is an inductor (a wire coil),
when energized with an electric pulse, will generate a
magnetic field. The second part of the relay is a system
of metallic arms, which makes up the physical contact of
the switch. When the replay is ON, or an electric pulse is
sent to the relay, the swing or switching arm of the relay
moves to another contact of the relay. The arm moves as
the generated magnetic field pulls the swinging arm
towards the inductor (or wire coil), the a.c. circuit is
completed and the electrical appliance is turned ON.

65
When the OFF button is clicked to turn off a device, the
software converts the OFF command into hex code, then
sends the value to USB port address. It sends logic 0 (0-
1.5V) to the microcontroller through the RS232
converter. Then the microcontroller sends a 0 to the
transistor. It will deactivate the transistor used to
energize the relay. The arm of the relay swings back to
another position, which makes the path of the current
flow open and hence electrical appliance is turned OFF.
The terminal input of each appliance is wired across,
then sends the value to USB port address. It sends logic
0 (0-1.5V) to the microcontroller through the RS232
converter. Then the microcontroller sends a 0 to the
transistor. It will deactivate the transistor used to
energize the relay, thus the power to the appliance is
switched ON or OFF depending on whether the relay is
active or not. The diagram of the flow chart design
system is as shown in Figure 7.
Figure 7: The flow chart of the designed system
IV. CONCLUSION
The user’s choice is clicked in the developed window
application through the PC and signal travels via the
USB cable to the corresponding connection. Based on
this command, the required appliance is triggered. It can
be used at homes, street light management, hotels,
power management, high voltage grid control and in
industries.
V. REFERENCES
[1] Al-Ali S.A, AL-Rousan M.T.(2004):"Home Automation
System". IEEE Transactions on Consumer Electronics,
Vol.50, No. 2, Pp. 13- 19.
[2] Anamul H.S.M, Kamruzzaman S.M. (2006):
"Microprocessor and Interfacing and
Hardware".Publication, Second Edition, Pp. 33- 41.
[3] Casimiro A, Kaiser J and Verissimo P.(2004):"An
Architecture Framework and Middleware for Control
Architecture for Home Automation System in the Internet
Era"Proceedings ICRA Cooperating Smart Components,
in Proc. Of CF’04 Italy, ACM. Pp. 28-39.
[4] Coyle L, Neely S, Stevenson G,Sullivan M, Dobson S
and Nixon P. (2007): "Sensor Fusion-Based Middleware
for Smart Homes".International Journal of ARM,
Vol.8,No. 2, Pp. 53-60
[5] Dickey N, Banks D and Sukittanon S. (2012): "Home
Automation using Cloud Network and Mobile Devices".
Proc. Of IEEE International Conference at Southeast on,
Electrotechnical Conference, MELECON 10th
Mediterranean, Vol. 1,Pp. 298- 301.
[6] Kim T, Lee H and Chung Y. (2010): "Advanced
Universal Remote Controller for Home Automation and
Security". IEEE Transaction on Consumer Electronics,
Vol. 56, No. 4, Pp. 2537- 2542.
[7] Kobatake S, Shirai H, Owada H and Yoshittomi K.
(1989): "HBS-Standard-Compatible Home Bus Protocol
Controller". IEEE Trans. On Consumer Electronics, Vol.
35,No. 3, Pp. 605-607.
[8] Koyuncu B. (1995): "PC Remote Control of Appliances
by using Telephone Lines". IEEE Transaction on
Consumer Electronics, Vol. 41.No. 1, Pp. 201- 209.
[9] Lin P and Broberg H. (2002): "HVAC Application".
IEEE Industry Application Magazine, Pp. 49- 54.
[10] Neng S L, Li-Chen F abd Chao-Lin W. (2002): "An
Integrated, Flexible and Internet- based Networks for
Home Automation". IEEE International Conference on
Robotics and Automation, Vol. 2, Pp. 1101- 1106.
[11] Nichols J and Myers B.A. (2006): "Controlling Home and
Office Appliances with Smart Phones".IEEE Pervasive
Computing, Pp. 60- 67.
[12] Nunes J and Delgado J. (2000): "An Internet Application
for Home Automation". Electrotechnical Conference,
MELECON, Vol. 1.Pp. 298- 301.
[13] Sriskanthan N and Tan K. (2002): "Bluetooth Based
Home Automation System". Journal of Microprocessors
and Microsystem, Vol. 26, Pp. 281- 289.
[14] Swamy N, Kuljaca O and Lewis F. (2002): "Internet-
Based Educational Control System Lab Using Net-
Meeting".IEEE Transaction on Education, vol. 45, No. 2,
Pp.145- 151.

A Microcontroller Framework For PC Based Electrical Appliance Control System

Recommended

More Related Content

Similar to A Microcontroller Framework For PC Based Electrical Appliance Control System (20)

More from Stephen Faucher (20)

Recently uploaded (20)

A Microcontroller Framework For PC Based Electrical Appliance Control System