Bobcat 763 skid steer loader service repair manual instant download (sn 512250001 & above)

6900977 (10-01) Printed in U.S.A. © Bobcat Company 2001
6900977 (2-06) Printed in U.S.A. © Bobcat Company 2006
Service
Manual
G Series
(S/N 512250001 & Above)
(S/N 512450001 & Above)
(S/N 512620001 & Above)
EQUIPPED WITH
BOBCAT INTERLOCK
CONTROL SYSTEM (BICS™)

MAINTENANCE SAFETY
Never service the Bobcat Skid-
Steer Loader without instructions.
Have good ventilation when
welding or grinding painted
parts.
Wear dust mask when grinding
painted parts. Toxic dust and gas
can be produced.
Avoid exhaust fume leaks which
can kill without warning. Exhaust
system must be tightly sealed.
Stop, cool and clean engine of
flammable materials before
checking fluids.
Never service or adjust loader
with the engine running unless
instructed to do so in the
manual.
Avoid contact with leaking
hydraulic fluid or diesel fuel
under pressure. It can penetrate
the skin or eyes.
Never fill fuel tank with engine
running, while smoking or when
near open flame.
Disconnecting or loosening any
hydraulic tubeline, hose, fitting,
component or a part failure can
cause lift arms to drop. Do not go
under lift arms when raised
unless supported by an
approved lift arm support device.
Replace it if damaged.
Keep body, jewelry and clothing
away from moving parts,
electrical contact, hot parts and
exhaust.
Wear eye protection to guard
from battery acid, compressed
springs, fluids under pressure
and flying debris when engines
are running or tools are used.
Use eye protection approved for
type of welding.
Keep rear door closed except for
service. Close and latch door
before operating the loader.
Never work on loader with lift
arms up unless lift arms are held
by an approved lift arm support
device. Replace if damaged.
Never modify equipment or add
attachments not approved by
Bobcat Company.
Lead-acid batteries produce
flammable and explosive gases.
Keep arcs, sparks, flames and
lighted tobacco away from
batteries.
Batteries contain acid which
burns eyes or skin on contact.
Wear protective clothing. If acid
contacts body, flush well with
water. For eye contact flush well
and get immediate medical
attention.
Use the correct procedure to lift or
lower operator cab.
Cleaning and maintenance are
required daily.
MSW08-0805
WRONG
B-16102
B-6589
B-10731a
CORRECT
B-15590
CORRECT
B-15591
CORRECT
B-15599
WRONG
WRONG
B-15593
WRONG
B-15592
B-15600
WRONG WRONG
B-16102
B-15601
WARNING
Instructions are necessary before operating or servicing machine. Read and
understand the Operation & Maintenance Manual, Operator’s Handbook and
signs (decals) on machine. Follow warnings and instructions in the manuals
when making repairs, adjustments or servicing. Check for correct function after
adjustments, repairs or service. Untrained operators and failure to follow
instructions can cause injury or death. W-2003-0903
Maintenance procedures which are given in the Operation & Maintenance Manual can be performed by the owner/
operator without any specific technical training. Maintenance procedures which are not in the Operation & Maintenance
Manual must be performed ONLY BY QUALIFIED BOBCAT SERVICE PERSONNEL. Always use genuine Bobcat
replacement parts. The Service Safety Training Course is available from your Bobcat dealer.
Safety Alert Symbol: This symbol with a warning statement, means: “Warning, be alert! Your safety is
involved!” Carefully read the message that follows.

ALPHABETICAL INDEX
ADVANCED CONTROL SYSTEM.......................... 60-01
ADVANCED HAND CONTROL SYSTEM............... 60-01
AIR CLEANER ........................................................ 70-01
AIR CLEANER SERVICE ....................................... 10-01
ALTERNATOR ........................................................ 60-01
BASCI TROUBLESHOOTING ................................ 80-01
BATTERY................................................................ 60-01
BOBCAT INTERLOCK
CONTROL SYSTEM (BICS™) .......................60-01
BOB-TACH ............................................... 10-01, 50-01
BRAKE.................................................................... 40-01
BUCKET POSITION VALVE ................................... 20-01
CHAINCASE ........................................................... 40-01
CHARGE PRESSURE............................................30-01
COMPONENTS ...................................................... 80-01
CONTROL HANDLE............................................... 50-01
CONTROL PANEL.................................................. 50-01
CONTROL PEDALS ............................................... 50-01
CONVERSIONS ............................................SPEC-01
COOLING FAN ....................................................... 70-01
CYLINDER(S) ..................................................... 20-01
DIAGNOSTICS ....................................................... 60-01
DRIVE BELT ........................................................... 30-01
DRIVE COMPONENTS .......................................... 40-01
ELECTRICAL/HYD. CONTROLS REFERENCE .... 60-01
ELECTRICAL SYSTEM INFORMATION ................ 60-01
ENGINE ................................................................. 70-01
ENGINE COMPONENTS AND TESTING .............. 70-01
ENGINE COOLING SYSTEM................................. 10-01
ENGINE LUBRICATION SYSTEM.......................... 10-01
ENGINE SPECIFICATIONS ...........................SPEC-01
ENGINE SPEED CONTROL .................................. 70-01
FAN GEARBOX ...................................................... 10-01
FINAL DRIVE TRANSMISSION (CHAINCASE) ..... 10-01
FLYWHEEL AND HOUSING ................................70-01
FRONT AUXILIARY PRESSURE RELIEF BLOCK 20-01
FRONT AUXILIARY HYDRAULIC
COUPLER BLOCK ............................................... 20-01
FUEL SYSTEM ....................................................... 10-01
FUEL TANK............................................................. 50-01
HEATER UNIT ........................................................ 80-01
HEATER COIL ........................................................ 80-01
HEATER FAN.......................................................... 80-01
HEATER VALVE...................................................... 80-01
HYDRAULIC CONNECTION SPECS................SPEC-01
HYDRAULIC CONTROL VALVE............................. 20-01
HYDRAULIC FLUID RESERVOIR.......................... 20-01
HYDRAULIC/HYDROSTATIC FILTER.................... 20-01
HYDRAULIC/HYDROSTAIC
FLUID SPECIFICATIONS............................... SPEC-01
HYDRAULIC PUMP ................................................20-01
HYDRAULIC/HYDROSTATIC SYSTEM..................10-01
HYDRAULIC SYSTEM INFORMATION ..................20-01
HYDROSTATIC MOTOR ..................................... 30-01
HYDROSTATIC PUMP ........................................ 30-01
HYDROSTATIC SYSTEM INFORMATION ..........30-01
INSTRUMENT PANEL.............................................60-01
LIFT ARM ................................................................50-01
LIFT ARM BY-PASS CONTROL VALVE..................20-01
LIFT ARM SUPPORT DEVICE ........................... 10-01
LIFTING AND BLOCKING THE LOADER...............10-01
LIGHTS ................................................................60-01
LOADER SPECIFICATIONS .............................SPEC-01
LUBRICATION OF THE BOBCAT LOADER ...........10-01
MAIN RELIEF VALVE..............................................20-01
MUFFLER................................................................70-01
OIL COOLER...........................................................30-01
OPERATOR CAB .........................................10-01, 50-01
OPERATOR SEAT...................................................50-01
POWER BOB-TACH BLOCK..................................20-01
REAR AXULIARY DIVERTER.................................20-01
REAR DOOR...........................................................50-01
REAR GRILL .......................................................50-01
RECONDITIONING THE ENGINE ..........................70-01
REGULAR MAINTENANCE ....................................80-01
REMOTE START .................................................10-01
RPM SENSOR ....................................................... 70-01
SEAT BAR ...............................................................50-01
SEAT BAR SENSOR.............................................. 60-01
SELECT VALVE.......................................................20-01
SERVICE SCHEDULE ............................................10-01
SPARK ARRESTOR MUFFLER..............................10-01
STARTER ................................................................60-01
SYSTEM TROUBLESHOOTING CHART .............. 80-01
TIRE MAINTENANCE .............................................10-01
TORQUE SPECIFICATIONS FOR BOLTS ... SPEC-01
TOWING THE LOADER..........................................10-01
TRACTION LOCK ...................................................60-01
TRANSPORTING THE BOBCAT LOADER.............10-01
TROUBLESHOOTING ............................................70-01

763 Bobcat Loader
I Service Manual
CONTENTS
FOREWORD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
SERIAL NUMBER LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IX
DELIVERY REPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IX
BOBCAT LOADER IDENTIFICATION. . . . . . . . . . . . . . . . . . . . . . . . X
SAFETY AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . 10-01
HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-01
HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-01
DRIVE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-01
MAIN FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-01
ELECTRICAL SYSTEM & ANALYSIS. . . . . . . . . . . . . . . . . . . . . 60-01
ENGINE SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-01
HEATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80-01
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPEC-01
SAFETY &
HYDROSTATIC
MAIN FRAME
SYSTEM
SYSTEM
DRIVE
ELECTRICAL
MAINTENANCE
SYSTEM &
ANALYSIS
ENGINE
SERVICE
ENGINE
SPECIFICATIONS
HVAC
SPECIFICATIONS
HYDRAULIC
SYSTEM

763 Bobcat Loader
II Service Manual
FOREWORD
This manual is for the Bobcat loader mechanic. It provides necessary servicing and adjustment
procedures for the Bobcat loader and its component parts and systems. Refer to the Operation &
Maintenance Manual for operating instructions, Starting procedure, daily checks, etc.
A general inspection of the following items must be made after the loader has had service or repair:
1. Check lift arm support device,
replace if damaged. (Stored
Position)
9. The parking brake must
function correctly.
2. Check that ROPS mounting
hardware is tightened and is
Bobcat approved.
10. Enclosure door latches must
open and close freely.
3. The seat belt must be
correctly installed, functional
and in good condition.
11. Bob-Tach wedges and
linkages must function
correctly and be in good
condition.
4. The seat bar must be
correctly adjusted, clean and
lubricated.
12. Safety treads must be in good
condition.
5. Check lift arm support device,
replace if damaged.
13. Check for correct function of
indicator lamps (Optional on
some models).
6. Machine signs must be
legible and in the correct
location.
14. Check hydraulic fluid level,
engine oil level and fuel
supply.
7. Steering levers and foot
pedals must return to neutral.
15. Inspect for fuel, oil or
hydraulic fluid leaks.
the work lights
16. Lubricate the loader.

763 Bobcat Loader
III Service Manual
17. Check the condition of the
battery and cables.
22. Operate the loader and check
all functions.
18. Inspect the air cleaner for
damage or leaks. Check the
condition of the element.
23. Check for any field
modification not completed.
19. Check the electrical charging
system.
the Bobcat Interlock Control
System (BICS™) before the
machine is returned to the
customer.
20. Check tires for wear and
pressure.
Recommend to the owner that all
necessary corrections be made
before the machine is returned to
service.
21. Inspect for loose or broken
parts or connections.
CALIFORNIA
PROPOSITION 65 WARNING
Diesel engine exhaust and some of its
constituents are known to the State of California
to cause cancer, birth defects and other
reproductive harm.

763 Bobcat Loader
V Service Manual
SAFETY INSTRUCTIONS
WARNING
Instructions are necessary before operating or
servicing machine. Read and understand the
Operation & Maintenance Manual, Operator’s
Handbook and signs (decals) on machine. Follow
warnings and instructions in the manuals when
making repairs, adjustments or servicing. Check for
correct function after adjustments, repairs or
service. Untrained operators and failure to follow
instructions can cause injury or death.
W-2003-0903
WARNING
Warnings on the machine and in the manuals are for
your safety. Failure to obey warnings can cause
injury or death.
W-2044-1285
IMPORTANT
This notice identifies procedures which must be
followed to avoid damage to the machine.
I-2019-0284
The following publications provide information on the
safe use and maintenance of the Bobcat machine and
attachments:
• The Delivery Report is used to assure that complete
instructions have been given to the new owner and
that the machine is in safe operating condition.
• The Operation & Maintenance Manual delivered with
the machine or attachment contains operating
information as well as routine maintenance and
service procedures. It is a part of the machine and can
be stored in a container provided on the machine.
Replacement Operation & Maintenance Manuals can
be ordered from your Bobcat dealer.
• Machine signs (decals) instruct on the safe operation
and care of your Bobcat machine or attachment. The
signs and their locations are shown in the Operation
& Maintenance Manual. Replacement signs are
available from your Bobcat dealer.
• An Operator’s Handbook fastened to the operator
cab. It’s brief instructions are convenient to the
operator. The handbook is available from your dealer
in an English edition or one of many other languages.
See your Bobcat dealer for more information on
translated versions.
• The AEM Safety Manual delivered with the machine
gives general safety information.
• The Service Manual and Parts Manual are available
from your dealer for use by mechanics to do shop-
type service and repair work.
• The Skid-Steer Loader Operator Training Course is
available through your local dealer or at
www.training.bobcat.com or www.bobcat.com.
This course is intended to provide rules and practices
of correct operation of the Skid-Steer Loader. The
course is available in English and Spanish versions.
• Service Safety Training Courses are available from
your Bobcat dealer or at www.training.bobcat.com
or www.bobcat.com. They provide information for
safe and correct service procedures.
• The Skid-Steer Loader Safety Video is available from
your Bobcat dealer or at www.training.bobcat.com
or www.bobcat.com.
SI SSL-0206 SM
This symbol with a warning statement means:
“Warning, be alert! Your safety is involved!”
Carefully read the message that follows.
Safety Alert Symbol

763 Bobcat Loader
VII Service Manual
SAFETY INSTRUCTIONS (CONT’D)
Fire Prevention
The machine and attachments have components that are
at high temperature under normal operating conditions.
The primary source of high temperatures is the engine
and exhaust system. The electrical system, if damaged
or incorrectly maintained, can be a source of arcs or
sparks.
Flammable debris (leaves, straw, etc.) must be removed
regularly. If flammable debris is allowed to accumulate, it
will increase fire hazard. Clean often to avoid this
accumulation. Flammable debris in the engine
compartment is a potential hazard.
The spark arrestor muffler is designed to control the
emission of hot particles from the engine and exhaust
system, but the muffler and the exhaust gases are still
hot.
• Do not use the machine where exhaust, arcs, sparks
or hot components can contact flammable material,
explosive dust or gases.
• The operator cab, engine compartment, and engine
cooling system must be inspected every day and
cleaned if necessary to prevent fire hazard and
overheating.
• Check all electrical wiring and connections for
damage. Keep the battery terminals clean and tight.
Repair or replace any damaged part.
• Check fuel and hydraulic tubes, hoses and fittings for
damage and leakage. Never use open flame or bare
skin to check for leaks. Tighten or replace any parts
that show leakage. Always clean fluid spills. Do not
use gasoline or diesel fuel for cleaning parts. Use
commercial nonflammable solvents.
• Do not use ether or starting fluids on any engine
which has glow plugs. These starting aids can cause
explosion and injure you or bystanders.
• Always clean the machine, disconnect the battery,
and disconnect the wiring from the controllers before
welding. Cover rubber hoses, battery and all other
flammable parts. Keep a fire extinguisher near the
machine when welding. Have good ventilation when
grinding or welding painted parts. Wear a dust mask
when grinding painted parts. Toxic dust or gas can be
produced.
• Stop the engine and let it cool before adding fuel. NO
SMOKING!
• Use the procedure in the Operation & Maintenance
Manual for connecting the battery and for jump
starting.
• Use the procedure in the Operation & Maintenance
Manual for cleaning the spark arrestor muffler (if
equipped).
Figure 1
• Know where fire extinguishers and first aid kits are
located and how to use them. Fire extinguishers are
available from your Bobcat dealer [Figure 1].
SI SSL-0206 SM

763 Bobcat Loader
IX Service Manual
SERIAL NUMBER LOCATION
Always use the serial number of the loader when
requesting service information or when ordering parts.
Early or later models (identification made by serial
number) may use different parts, or it may be necessary
to use a different procedure in doing a specific service
operation.
Loader Serial Number
Figure 2
The loader serial number plate is located on the outside
of the loader frame [Figure 2].
Explanation of loader Serial Number:
1. The four digit Model/Engine Combination Module
number identifies the model number and engine
combination.
2. The five digit Production Sequence Number identifies
the order which the loader is produced.
Engine Serial Number
Figure 3
The engine serial number is located on the valve cover at
the right side of the engine [Figure 3]. There is also an
extra S/N tag attached to the engine [Figure 4]
DELIVERY REPORT
Figure 4
The Delivery Report must be filled out by the dealer and
signed by the owner or operator when the Bobcat loader
is delivered. An explanation of the form must be given to
the owner. Make sure it is filled out completely [Figure
4].
P13880
XXXX XXXXX
Model 1.-Model/ Engine
Combination
Model 2.-Production
Sequence (Series)
N-20521
B-16315

763 Bobcat Loader
X Service Manual
BOBCAT LOADER IDENTIFICATION
‹ OPTIONAL OR FIELD ACCESSORY (Not Standard Equipment)
* TIRES - Flotation tires ▼ are shown. The Bobcat loader is factory equipped with standard tires.
+ BUCKET - Several different buckets and other attachments are available for the Bobcat loader.
z ROPS, FOPS - Roll Over Protective Structure, per SAE J1040 and ISO 3471, and Falling Object Protective
Structure per SAEJ1043 and ISO 3449, Level I. Level II is available. The Bobcat loader is base-equipped with
a standard operator cab as shown. Extra insulated cab is available as an option (Reduced noise level).
FRONT AUXILIARY
QUICK COUPLERS
TILT CYLINDER
BUCKET
LIFT ARM
* TIRES
TAIL LIGHT
REAR DOOR
REAR
LIGHT
REAR GRILL
zOPERATOR CAB
(ROPS & FOPS)
BUCKET STEPS
B-15631
GRAB HANDLES
SAFETY TREAD
OPERATOR SEAT
WITH SEAT BELT
B-15632
FRONT LIGHTS
†
‹
‹
REAR AUXILIARY
QUICK COUPLERS
‹
STEERING
LEVER
‹REAR WINDOW
‹
‹
LIFT CYLINDER
LIFT ARM
SUPPORT DEVICE

763 Bobcat Loader
10-01 Service Manual
SAFETY AND MAINTENANCE
AIR CLEANER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1
Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1
Replacing Filter Element(s) . . . . . . . . . . . . . . . . . . . . . . . . 10-80-1
BOB-TACH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-150-1
Inspection And Maintenance . . . . . . . . . . . . . . . . . . . . . . 10-150-1
ENGINE COOLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . 10-90-1
Checking The Coolant Level . . . . . . . . . . . . . . . . . . . . . . . 10-90-2
Cleaning The Cooling System . . . . . . . . . . . . . . . . . . . . . . 10-90-1
Replacing The Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-90-2
ENGINE LUBRICATION SYSTEM . . . . . . . . . . . . . . . . . . . . 10-110-1
Checking Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-110-1
Oil Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-110-1
Replacing Oil And Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 10-110-1
FAN GEARBOX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-140-1
Checking And Maintaining . . . . . . . . . . . . . . . . . . . . . . . . 10-140-1
FINAL DRIVE TRANSMISSION (CHAINCASE) . . . . . . . . . . 10-130-1
Checking And Adding Oil. . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1
Removing The Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-130-1
FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-100-1
Filling the Fuel Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-100-1
Fuel Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-100-2
Fuel Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-100-1
Removing Air From The Fuel System . . . . . . . . . . . . . . . 10-100-2
HYDRAULIC/HYDROSTATIC SYSTEM . . . . . . . . . . . . . . . . 10-120-1
Breather Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-120-4
Checking And Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . 10-120-1
Replacing Hydraulic Fluid . . . . . . . . . . . . . . . . . . . . . . . . 10-120-3
Replacing Hydraulic/Hydrostatic Filter. . . . . . . . . . . . . . . 10-120-2
Replacing Hydrostatic Motor Case Drain Filter(s) . . . . . . 10-120-2
LIFT ARM SUPPORT DEVICE . . . . . . . . . . . . . . . . . . . . . . . . 10-20-1
Installing Lift Arm Support Device . . . . . . . . . . . . . . . . . . . 10-20-1
Removing The Lift Arm Support Device. . . . . . . . . . . . . . . 10-20-2
LIFTING AND BLOCKING THE LOADER . . . . . . . . . . . . . . . 10-10-1
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10-1
Continued On Next Page
SAFETY &
SYSTEM
DRIVE
ELECTRICAL
MAINTENANCE
SYSTEM &
ANALYSIS
ENGINE
SERVICE
SPECIFICATIONS

763 Bobcat Loader
10-02 Service Manual
SAFETY AND MAINTENANCE (CONT’D)
LUBRICATION OF THE BOBCAT LOADER. . . . . . . . . . . . . 10-160-1
Pivot Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-160-2
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-160-1
OPERATOR CAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-30-1
Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-30-1
Emergency Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-30-3
Lowering The Operator Cab . . . . . . . . . . . . . . . . . . . . . . . 10-30-2
Raising The Operator Cab. . . . . . . . . . . . . . . . . . . . . . . . . 10-30-1
REMOTE START. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-60-1
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-60-1
SERVICE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1
Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-70-1
SPARK ARRESTOR MUFFLER . . . . . . . . . . . . . . . . . . . . . . 10-180-1
Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-180-1
TIRE MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-170-1
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-170-1
Rotating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-170-1
Wheel Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-170-1
TOWING THE LOADER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-50-1
TRANSPORTING THE BOBCAT LOADER . . . . . . . . . . . . . . 10-40-1
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40-1
TIGHTEN ALL HARDWARE PER SIZE TO GRADE 5 TORQUE (See TORQUE SPECIFICATIONS FOR BOLTS on
Page SPEC-30-1.) UNLESS OTHERWISE SPECIFIED.

763 Bobcat Loader
10-10-1 Service Manual
LIFTING AND BLOCKING THE LOADER
Procedure
Figure 10-10-1
WARNING
Instructions are necessary before operating or
servicing machine. Read and understand the
Operation & Maintenance Manual, Handbook and
signs (decals) on machine. Follow warnings and
instructions in the manuals when making repairs,
adjustments or servicing. Check for correct function
after adjustments, repairs or service. Untrained
operators and failure to follow instructions can cause
injury or death.
W-2003-0199
Always park the loader on a level surface.
WARNING
Put jackstands under the front axles and rear corners
of the frame before running the engine for service.
Failure to use jackstands can allow the machine to
fall or move and cause injury or death.
W-2017-0286
Figure 10-10-2
Put floor jack under the rear of the loader [Figure 10-10-
2].
Lift the rear of the loader and install jackstands [Figure
10-10-2].
Figure 10-10-3
Put the floor jack under the front of the loader [Figure 10-
10-3].
Lift the front of the loader and put jackstands under the
axle tubes [Figure 10-10-3].
NOTE: Make sure the jackstands do not touch the
tires. Make sure tires clear floor or any
obstacles.
B-7023
N-20605
P-3868

763 Bobcat Loader
LIFT ARM SUPPORT DEVICE
Installing Lift Arm Support Device
WARNING
Never work on a machine with the lift arms up unless
the lift arms are secured by an approved lift arm
support device. Failure to use an approved lift arm
support device can allow the lift arms or attachment
to fall and cause injury or death.
W-2059-0598
WARNING
Service lift arm support device if damaged or if parts
are missing. Using a damaged lift arm support or
with missing parts can cause lift arms to drop
causing injury or death.
W-2271-1197
Figure 10-20-1
Put jackstands under the rear corners of the loader frame
(Inset) [Figure 10-20-1].
Disconnect the spring from the lift arm support device
retaining pin (Item 1) [Figure 10-20-1]. Support the lift
arm support device (Item 2) [Figure 10-20-1] with your
hand and remove the retaining pin.
Figure 10-20-2
Lower the lift arm support device on top of the lift
cylinder. Hook the free end of the spring (Item 1) [Figure
10-20-2] to the lift arm support device so there will be no
interference with the support device engagement.
With the operator in the seat, seat belt fastened and seat
bar lowered, start the engine.
N-20526
N-20605
1
2
N-20525
1

763 Bobcat Loader
LIFT ARM SUPPORT DEVICE (CONT’D)
Installing Lift Arm Support Device (Cont’d)
Figure 10-20-3
Raise the lift arms, until the lift arm support device drops
onto the lift cylinder rod [Figure 10-20-3].
Lower the lift arms slowly until the support device is held
between the lift arm and the lift cylinder. Stop the engine.
Raise the seat bar and move pedals until both pedals
lock.
Install pin (Item 1) [Figure 10-20-3] into the rear of the lift
arm support device below the cylinder rod.
Removing The Lift Arm Support Device
Figure 10-20-4
Remove the pin from the lift arm support device.
Connect the spring (Item 1) [Figure 10-20-4] from the lift
arm support device to the bracket below the lift arms.
With the operator in the seat, seat belt fastened and seat
bar lowered, start the engine.
Raise the lift arms a small amount and the spring will lift
the support device off the lift cylinder rod. Lower the lift
arms. Stop the engine.
Raise the seat bar and move pedals until both pedals
lock.
Disconnect the spring from the bracket.
N-20524
1
N-20523
1

763 Bobcat Loader
LIFT ARM SUPPORT DEVICE (CONT’D)
Removing The Lift Arm Support Device (Cont’d)
Figure 10-20-5
Raise the support device into storage position and insert
pin (Item 1) [Figure 10-20-5] through lift arm support
device (Item 2) [Figure 10-20-5] and bracket. Connect
spring to pin.
Remove jackstands.
N-20526
1
2

763 Bobcat Loader
OPERATOR CAB
Description
The Bobcat loader has an operator cab (ROPS and
FOPS) as standard equipment to protect the operator
from rollover and falling objects. Check with your dealer if
the operator cab has been damaged. The seat belt must
be worn for roll over protection.
ROPS/FOPS - Roll Over Protective Structure per SAE
J1040 and ISO 3471, and Falling Object Protective
Structure per SAE J1043 and ISO 3449, Level I. Level II
is available.
Level I - Protection from falling bricks, small concrete
blocks, and hand tools encountered in operations such
as highway maintenance, landscaping, and other
construction site services.
Level II - Protection from falling trees, rocks; for machines
involved in site clearing, overhead demolition or forestry.
Raising The Operator Cab
Always stop the engine before raising or lowering the
cab.
NOTE: Make sure the seat bar is fully raised or
lowered when lowering the cab. Always use
the grab handles to lower the cab.
Stop the loader on a level surface. Lower the lift arms. If
the lift arms must be up while raising the operator cab,
install the lift arm support device. (See Installing Lift Arm
Support Device on Page 10-20-1.)
Figure 10-30-1
Install jackstands under the rear of the loader frame
[Figure 10-30-1].
Advanced Hand Control and Control System
WARNING
Never modify operator cab by welding, grinding,
drilling holes or adding attachments unless
instructed to do so by Bobcat. Changes to the cab
can cause loss of operator protection from rollover
and falling objects, and result in injury or death.
W-2069-1299
Figure 10-30-2
Loosen the nut (both sides) at the front corners of the
operator cab [Figure 10-30-2]
Remove the nuts and plates [Figure 10-30-2] (both
sides).
N-20605
N-20519
N-20520

763 Bobcat Loader
OPERATOR CAB (CONT’D)
Raising The Operator Cab (Cont’d)
Figure 10-30-3
Lift on the grab handle and bottom of the operator cab
slowly until the cab is all the way up and the latching
mechanism engages[Figure 10-30-3].
Figure 10-30-4
Advanced Hand Controls Only
Lowering The Operator Cab
Always stop the engine before raising or lowering the
cab.
NOTE: Make sure the seat bar is fully raised or
lowered when lowering the cab. Always use
the grab handles to lower the cab.
Pull down on the bottom of the operator cab until it stops
at the latching mechanism[Figure 10-30-4].
Release the latching mechanism (Inset) [Figure 10-30-4]
and pull the cab all the way down.
P-30074
P-30074
N-20120

763 Bobcat Loader
Lowering The Operator Cab (Cont’d)
Figure 10-30-5
Install the plates and nuts [Figure 10-30-5] (both sides).
Tighten the nuts to 40-50 ft.-lbs. (54-68 Nm) torque.
Emergency Exit
Figure 10-30-6
The front opening on the operator cab and rear window
provide exits.
Rear Window (If Equipped)
Pull on the tag on the top of the rear window to remove
the rubber cord [Figure 10-30-6].
Figure 10-30-7
Push the rear window out of the rear of the operator cab.
Exit through the rear of the operator cab [Figure 10-30-
7].
Figure 10-30-8
Front Door (If Equipped)
NOTE: When an Operator Cab Enclosure Kit is
installed, the window of the front door can be
used as an emergency exit [Figure 10-30-8].
Pull the plastic loop at the top of the window in the front
door to remove the rubber cord [Figure 10-30-8].
N-20519
N-20519
N-20519
N-20520
N-19386
N-20606
N-20171

763 Bobcat Loader
Emergency Exit (Cont’d)
Figure 10-30-9
Figure 10-30-10
Push the window out with your foot [Figure 10-30-9] at
any corner of the window.
Exit through the front door.
P-30255
X

763 Bobcat Loader
TRANSPORTING THE BOBCAT LOADER
Procedure
Figure 10-40-1
WARNING
Adequately designed ramps of sufficient strength are
needed to support the weight of the machine when
loading onto a transport vehicle. Wood ramps can
break and cause personal injury.
W-2058-0494
A loader with an empty bucket or no attachment must be
loaded backward onto the transport vehicle[Figure 10-
40-1].
Be sure the transport and towing vehicles are of
adequate size and capacity. (See Performance on Page
SPEC-10-2.)
The rear of the trailer must be blocked or supported (Item
1)[Figure 10-40-1] when loading or unloading the loader
to prevent the front end of the trailer from raising up.
Figure 10-40-2
Use the following procedure to fasten the Bobcat loader
to the transport vehicle to prevent the loader from moving
during sudden stops or when going up or down slopes
[Figure 10-40-2].
• Lower the bucket or attachment to the floor.
• Stop the engine.
• Engage the parking brake.
• Install chains at the front and rear loader tie down
positions (Inset) [Figure 10-40-2].
• Fasten each end of the chain to the transport vehicle.
N-20660
1
N-19048 N-19073
N-20659

763 Bobcat Loader
TOWING THE LOADER
Procedure
Figure 10-50-1
To prevent damage to the loaders hydrostatic system, the
loader must be towed only a short distance at slow
speed. (Example: Moving the loader onto a transport
vehicle).
The towing chain (or cable) must be rated at 1 & 1/2
times the weight of the loader. (See Performance on
Page SPEC-10-2.)
• Turn the key switch to RUN (Item 1) [Figure 10-50-1]
(Standard Panel) OR press the RUN/ENTER Button
(Deluxe Panel).
Figure 10-50-2
• Press the TRACTION LOCK OVERRIDE Button
(Item 1)[Figure 10-50-2].
• Tow the Bobcat at 2 MPH (3,2 km/hr) or less for not
more than 25 feet (7,6 meters).
If the electrical system is not functioning or the engine
does not run part of the brake system must be
disassembled to move the loader. (See TRACTION
LOCK on Page 60-110-1.)
N-18410
1
N-18409
1

763 Bobcat Loader
REMOTE START
Procedure
WARNING
AVOID INJURY OR DEATH
With the 7-pin connector plugged into the loader and
Remote Start Key Switch in the OFF position, the
loader can still be started from the operator panel
inside the cab. Placing the key switch of the remote
start tool in the run position disconnects the
operator panel key switch from the start circuit. If the
service technician will be working the engine area it
is important to remove the operator panel keys.
W-2357-0899
Figure 10-60-1
The tool listed will be need to do the following procedure:
MEL1563: Remote Start Tool Kit
The remote start tool (Item 1) [Figure 10-60-1] is
required when the operator cab is in the raised position
for service and the service technician needs to turn the
key switch on or start the engine. Example: adjusting the
steering linkage.
Figure 10-60-2
Figure 10-60-3
Lift and block the loader. (See LIFTING AND BLOCKING
THE LOADER on Page 10-10-1.)
Raise the lift arms (if required by the procedure) and
install an approved lift arm support device. (See Installing
Lift Arm Support Device on Page 10-20-1.)
Raise the operator cab (if required by the procedure).
(See Raising The Operator Cab on Page 10-30-1.)
Open the rear door of the loader.
Remove the plug (Item 1) [Figure 10-60-2] or disconnect
the attachment control harness (Item 1) [Figure 10-60-3]
if connected.
N-20862
1
P-28793
1
P-28823
1

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

763 Bobcat Loader
REMOTE START (CONT’D)
Procedure (Cont'd)
Figure 10-60-4
Connect the remote start tool to the engine harness
connector (Item 1) [Figure 10-60-4].
NOTE: The key switch on the right-hand side
operator panel must be in the off position or
the Remote Start Kit will not operate.
Figure 10-60-5
The remote start tool (Item 1) [Figure 10-60-5] has three
rocker switches.
Figure 10-60-6
The traction lock switch (Item 1) [Figure 10-60-6] is used
to turn traction lock on or off. Push the switch to the
override position. The switch will illuminate to indicate
traction lock OVERRIDE, in this position the wheels are
able to turn.
The maximum flow/variable flow switch (Item 2) [Figure
10-60-6] is used to activate the auxiliary hydraulics.
Pressing the switch once will activate variable flow.
Pressing the switch again will activate maximum flow.
The switch will illuminate to indicate which flow rate is
active. Pressing the switch a third time will turn the flow
OFF. The switch is used when checking pressures and
flow rate.
S/N 512263234 & Below
The auxiliary pressure release (Item 3) [Figure 10-60-6]
is used to release hydraulic pressure to the front and/or
rear auxiliary couplers. To release pressure; push and
hold the switch for three seconds.
NOTE: With the engine running; pushing and holding
the pressure release switch this will cause the
engine to stop in three seconds. To relieve the
pressure; continue to press the switch after
the engine has stopped.
P-28806
1
N-20862
1
N-20861
1
2
3

Bobcat 763 skid steer loader service repair manual instant download (sn 512250001 & above)

More Related Content

Similar to Bobcat 763 skid steer loader service repair manual instant download (sn 512250001 & above) (20)

More from udfjsjjekkekmem (20)

Recently uploaded (20)