Canal irrigation

Pranamesh Chakraborty
Introduction
A canal is defined as an artificial channel
constructed on the ground to carry water from
a river or another canal or a reservoir to the
fields.

Types of Canals

Types of Canals
(BASED ON SOURCE OF SUPPLY)
• Continuous source of water
supply.
• Also called perennial canals
Permanent
Canal
• Draws its supplies from a river
only during the high stages of
the river.
Inundation
Canal

Types of Canals
(BASED ON FUNCTION)
• Carries water from its source to
agricultural fields.
Irrigation
Canal
• Used for transport of goods.
Navigation
Canal
• Used to carry water for
generation of hydroelectricity.Power Canal
• Feeds two or more canals.Feeder Canal
Note, a canal can serve more than one purpose.

Types of Canals
(BASED ON ALIGNMENT)
Watershed Canal or
Ridge Canal
Contour Canal
Side Slope Canal

Watershed canal or Ridge canal

Watershed canal or Ridge canal (Contd.)
The dividing ridge line between the catchment areas of two streams
(drains) is called the watershed or ridge canal.
 Thus between two major streams, there is the main watershed
(ridge line), which divides the drainage area of the two streams.

The canal which is aligned along any natural watershed (ridge line)
is called a watershed canal, or a ridge canal. Aligning a canal (main
canal or branch canal or distributary) on the ridge ensures gravity
irrigation on both sides of the canal.
 Since the drainage flows away from the ridge, no drainage can
cross a canal aligned on the ridge. Thus, a canal aligned on the
watershed saves the cost of construction of cross-drainage works.

Contour Canal
Watershed canal along the ridge line are not found economical in
hill areas. In hills, the river flows in the valley well below the
watershed.
In fact, the ridge line (watershed) may be hundred of meters above
the river. It therefore becomes virtually impossible to take the canal
on top of such a higher ridge line. In such conditions, contour canals
are usually constructed.
A contour canal irrigates only on one side because the area on the
other side is higher.

Contour Canal (Contd.)

Side Slope Canal
A side slope canal is that which is aligned at right angles to the
contours; i.e. along the side slopes.
Since such a canal runs parallel to the natural drainage flow, it
usually does not intercept drainage channels, thus avoiding the
construction of cross-drainage structures.
It is a canal which is aligned roughly at right angle to contours of
the country but not on watershed or valley.

Side Slope Canal (Contd.)

Types of Canals
(BASED ON DISCHARGE)
Main Canal
Branch Canal
Major Distributary
Minor Distributary
Water Course

MAIN CANAL
Main Canal takes off directly from the
upstream side of weir head works or dam.
Usually no direct cultivation is proposed

The Danube-Black Sea Canal in Romania

BRANCH CANAL
All offtakes from main canal with head
discharge of 14-15 cumecs and above are
termed as branch canals.
Acts as feeder channel for major distributaries

MAJOR DISTRIBUTARY
 All offtakes from main canal or branch canal with head
discharge from 0.25 to 15 cumecs are termed as major distributaries.
MINOR DISTRIBUTARY
 All offtakes taking off from a major distributary carrying
discharge less than 0.25 cumec are termed as minor distributaries
WATER COURSE
 Small channels which carry water from the outlets of a major
or minor distributary or a branch canal to the fields to be
irrigated.

Types of Canals
(Based on lining provided or not)
• Bed and banks made up of natural soil.
• Water velocities higher than 0.7 m/s are not
tolerable.
• High seepage and conveyance water losses.
• Profuse growth of aquatic weeds retards the
flow .
Unlined
Canal
• Lining of impervious material on its bed and
banks to prevent the seepage of water.
• Different types of lining used e.g. concrete,
brick or burnt clay tile, boulder, etc.
Lined
Canal

Cross-Section of
Irrigation Canal

Introduction
FSL= Full Supply Level. NSL=Natural Surface Level
This section is partly in cutting and partly in filling and aims in
balancing the quantity of earth work in excavation with that in
filling.

Introduction
When the NSL is above the top of the bank, the entire
canal section will have to be in cutting, and it shall be
called ‘canal in cutting’.
Similarly, when the NSL is lower than the bed level of
the canal, the entire canal section will have to be built in
filling, and it is called ‘canal in filling’.

Components of Cross- Section
 Side slope
 Berm
 Freeboard
 Bank
 Service road
 Back Berm or Counter Berm
 Spoil Bank
 Borrow Pit

Side Slope
The side slopes should be such that they are stable,
depending upon the type of the soil.
A comparatively steeper slope can be provided in
cutting rather than in filling, as the soil in the former case
shall be more stable.

Berm
Berm is the horizontal distance left at ground level between
the toe of the bank and the top edge of cutting.

Berm (contd.)
Purposes of Berms:
 They give additional strength to the banks and provide
protection against erosion and breaches.
 They protect the banks from erosion due to wave action.
 They provide a scope for future widening of the canal.

Freeboard
The margin between FSL and bank level is known as
freeboard. The amount of freeboard depends upon the
discharge of the channel.

Bank
The primary purpose of banks in to retain water. This can be
used as means of communication and as inspection paths.

Service Road
Service roads are provided on canals for inspection purposes, and may
simultaneously serve as the means of communication in remote areas.
Dowla: As a measure of safety in driving, dowlas with side slopes of
1.5: 1 to 2:1, are provided along the banks.

Back Berm or Counter Berm
Even after providing sufficient section for bank embankment, the
saturation gradient line may cut the downstream end of the bank. In
such a case, the saturation line can be kept covered at least by 0.5 m
with the help of counter berms as shown in figure below.

Spoil Bank
When the earthwork in excavation exceeds earthworks in filling, the
extra earth has to be disposed of economically.
Economical mode of its disposal may be collecting this soil on the
edge of the bank embankment itself.

Borrow Pit
When earthwork in filling exceeds the earthwork in
excavation, the earth has to be brought from somewhere.
The pits, which are dug for bringing earth, are known as
borrow pits.
If such pits are excavated outside the channel, they are known
as external borrow pits, and if they are excavated somewhere
within the channel, they are known as internal borrow pits.
Internal borrow pits are more preferred than external one.

Borrow Pit (Contd.)
The inside borrow pit may be located at the centre of canal. The idea
behind this is that the borrow pits will act as water pockets where the
silt will be deposited and ultimately the canal bed will get levelled up.

Example
Calculate the balancing depth for a channel section having a bed width
equal to 18 m and side slopes of 1:1 in cutting and 2:1 in filling. The
bank embankments are kept 3.0 m higher than the ground level (berm
level) and crest width of banks is kept as 2.0 m.
Solution: Let d be the balancing depth, i.e. the depth for which
excavation and filling becomes equal.

Example (Contd.)
Area of cutting = (18 + d) d m2
Area of filling = 2(2+14)/2×3 = 48 m2
Equating cutting and filling, we get
(18 + d) d = 48
or, d2 + 18d – 48 = 0
or, d = 2.35 m (neglecting –ve sign)
Balancing depth = 2.35 m

Losses of water in canal

Types of losses of water in canals
Loss of
water in
canal
Evaporation
Loss
Seepage
Loss
Percolation Absorption

Evaporation Loss
The water lost by evaporation is generally very
small, as compared to seepage loss.
Evaporation Loss are generally 2-3% of total loss
(max. 7% in summer)

Seepage Loss
Percolation:
In percolation, there exist a zone of continuous
saturation from canal to water table and direct flow is
established.

Seepage Loss
Percolation:
Almost all water lost from canal reaches ground water
reservoir.
Loss of water depends on the difference of the top water
surface level of channel and level of water-table.

Seepage Loss
Absorption:
In absorption, a small saturated zone exist round the canal
section and is surrounded by zone of decreasing saturation.
A certain zone just above water table is saturated by
capillarity.

Seepage Loss
Absorption:
Thus, there exists an unsaturated soil zone between two
saturated zones.
This result in seepage loss.

Canal Lining

Advantages of Lining
 Water Conservation: Lining a canal results in reduction
in water losses, as water losses in unlined irrigation canals can be
high.
 No seepage of water into adjacent land or roads: If
canal banks are highly permeable, the seepage of water will cause
very wet or waterlogged conditions, or even standing water on
adjacent fields or roads. Lining of such a canal can solve this
problem.

Advantages of Lining (Contd.)
Reduced canal dimensions: The resistance to flow of a
lined canal is less than that of an unlined canal, and thus the flow
velocity will be higher in the lined canal . Therefore, with the
higher velocity, the canal cross-section for a lined canal can be
smaller than that of an unlined canal.
 Reduced maintenance: Maintenance costs for the
following issues are eliminated using lining of canals.
 Periodical removal of silt deposited on the beds and sides of
canals.
 Removal of weeds and water canals.
 Minor repairs like plugging of cracks, uneven settlements of
banks, etc.

Types of lining
Hard Surface Lining
Cast Insitu Cement
Concrete Lining
Shotcrete or Plastic
Lining
Cement Concrete Tile
Lining or Brick Lining
Asphaltic Concrete
Lining
Boulder Lining
Earth Type Lining
Compacted Earth
Lining
Soil Cement
Lining

Cast In-Situ Concrete Lining

Thank You

Canal irrigation

More Related Content

What's hot (20)

Similar to Canal irrigation (20)

More from Pranamesh Chakraborty (11)

Recently uploaded (20)

Canal irrigation