Canal regulation works. m4pptx
110 likes51,064 views
The document discusses canal regulation works, focusing on various structures such as canal falls, regulators, and escapes essential for managing water flow in canal systems. It details the types of falls (ogeefall, rapid fall, trapezoidal notch fall, vertical drop fall) and their specific applications, along with the purpose and design criteria for cross regulators and escapes used to control excess water. Additionally, it outlines the need for sediment control devices like silt vanes and groyne walls to maintain water quality and reduce siltation.
Canal regulation works. m4pptx
- 1. MODULE- 4 Canal regulation works Prepared by Bibhabasu Mohanty Dept. of Civil Engineering SALITER, Ahmedabad
- 2. Content… Canal fall- necessity and location- types of falls- Cross regulator and distributory head regulator- their functions, Silt control devices, Canal escapes- types of escapes.
- 3. Introduction canal obtains its share of water from the pool behind a barrage through a structure called the canal head regulator also a regulation structure for controlling the amount of water passing into the canal In this lesson, attention focussed on structures that regulate the discharge and maintain the water levels within a canal network
- 5. These structures may be described as follows: 1. Drops and falls, to lower the water level of the canal 2. Cross regulators, to head up water in the parent channel to divert some of it through an off take channel, like a distributary. 3. Distributary head regulator, to control the amount of water flowing in to off take channel. 4. Escapes, to allow release of excess water from the canal system.
- 6. Canal drops and falls canal has a designed longitudinal slope but has to pass through an undulating terrain. When a canal crosses an area that has a larger natural surface slope, a canal drop, also called fall in India, has to be provided suitably at certain intervals.
- 8. location of fall judiciously worked out such that there should be a balance between the quantities of excavation and filling. height of the fall has to be decided, since it is possible to provide larger falls at longer intervals or smaller falls at shorter intervals.
- 9. Necessity of canal falls When slope of ground suddenly changes to steeper slope, permissible bed slope cannot be maintained. Slope of ground is more or less uniform and slope is greater than permissible bed slope of canal. In cross drainage work, when difference between level of canal and that of drainage is small or when F.S.L of canal is above bed level.
- 10. Types of canal fall 1. Ogee fall an ogee curve (combination of convex and concave curve) provided for carrying canal water from higher level to lower level. Fall is recommended when natural ground surface suddenly changes to a steeper slope along the alignment of the canal.
- 11. Fall consists of a concrete vertical wall and concrete bed. Over the concrete bed the rubble masonry is provided in the shape of ogee curve. Upstream and downstream of the fall is protected by stone pitching.
- 13. 2. Rapid fall When slope of the natural ground surface is even and long. Consists of long glacis with longitudinal slope. Curtain walls are provided on the upstream and downstream side of the sloping glacis.
- 15. 3. Trapezoidal notch fall Body wall is constructed across the canal. Body wall consists of several trapezoidal notches between side piers and intermediate piers. Notches are kept at the upstream bed level of canal. Body wall is constructed with masonry or concrete.
- 17. 4. Vertical drop fall Consists of vertical drop wall constructed with masonry work. Water flows over the crest of wall. Concrete floor provided on downstream side to control scouring effect. Curtain wall provided on upstream and downstream side. This type falls provided at Sardar canal, UP. Hence known as sardar fall.
- 19. Canal regulators include the cross regulator and the distributary head regulator structures for controlling the flow through a parent canal and its off-taking distributary . help to maintain the water level in the canal on the upstream of the regulator.
- 21. angle at which a distributary canal off-takes from the parent canal has to be decided carefully. The best angle is when the distributary takes off smoothly. Another alternative is to provide both channels (off-taking and parent) at an angle to the original direction of the parent canal. When it becomes necessary for the parent canal to follow a straight alignment, the edge of the canal rather than the centre line should be considered in deciding the angle of off-take.
- 23. To prevent excessive entry of silt deposition at the mouth of the off-take, the entry angle should be kept to between 600 and 800. For the hydraulic designs of cross regulators, one may refer to the Bureau of Indian Standard code IS: 7114-1973 “Criteria for hydraulic design of cross regulators for canals”.
- 24. The distributary should preferably be designed to draw sediment proportional to its flow, for maintaining non-siltation of either the parent canal or itself. three types of structures have been suggested as discussed below along with the relevant Bureau of Indian standard codes.
- 25. Silt vanes are thin, vertical, curved parallel walled structures constructed of plain or reinforced concrete on the floor of the parent canal, just upstream of the off- taking canal. height of the vanes may be about one- fourth to one-third of the depth of flow in the parent canal.
- 26. thickness of the vanes should be as small as possible and the spacing of the vanes may be kept about 1.5 times the vane height. To minimize silting tendency, the pitched floor on which the vanes are built should be about 0.15 m above the normal bed of the parent channel.
- 28. Groyne walls or curved wings project out in to the parent canal from the downstream abutment of the off-taking canal. it divides the discharge of the parent canal in proportion of the discharge requirement of the off-taking canal with respect to the flow in the downstream parent canal.
- 29. The groyne wall extends upstream in to the parent canal to cover ¾ to full width of the off-take. proportional distribution of flow in to the off-taking canal is expected to divert proportional amount of sediment. The height of the groyne wall should be at least 0.3m above the full supply level of the parent canal.
- 31. Skimming platforms A skimming platform is an RCC slab resting on low height piers on the bed of the parent canal, and in front of the off- taking canal. creates a kind of low tunnel at the bed of the parent canal, which allows the sediment moving along its bed to pass through downstream.
- 32. floor of the off-taking canal being above the level of the platform thus only takes suspended sediment load coming along with the main flow in the parent canal. suitable where the parent channel is deep (about 2m or more) and the off-take is comparatively small.
- 33. The tunnels should be at-least 0.6m deep. The upstream and downstream edges of the platform should be inclined at about 300 to the parent canal cross section.
- 35. Canal escapes structures meant to release excess water from a canal, which could be main canal, branch canal, distributary, minors etc. usually an irrigation system suffers from deficit supply in later years of its life situations that might suddenly lead to accumulation of excess water in a certain reach of a canal network may occur due to the following reasons:
- 36. 1.Wrong operation of head works in trying to regulate flow in a long channel resulting in release of excess water than the total demand in the canal system downstream. 2. Excessive rainfall in the command area leading to reduced demand and consequent closure of downstream gates. 3. Sudden closure of control gates due to a canal bank breach.
- 37. The excess water in a canal results in the water level rising above the full supply level which, if allowed to overtop the canal banks, may cause erosion and subsequent breaches. Hence, canal escapes help in releasing the excess water from a canal at times of emergency.
- 38. Escapes as also built at the tail end of minors at the far ends of a canal network. These are required to maintain the required full supply level at the tail end of the canal branch.
- 39. Weir or surface escapes are constructed in the form of weirs, without any gate or shutter and spills over when the water level of the canal goes above its crest level.
- 41. Sluice or surplus escapes gated escapes with a very low crest height. these sluices can empty the canal much below its full supply level and at a very fast rate. In some cases, these escapes act as scouring sluices to facilitate removal of sediment.
- 43. The locations for providing escapes are often determined on the availability of suitable drains, depressions or rivers with their bed level at or below the canal bed level. Escapes may be necessary upstream of points where canals takeoff from a main canal branch.
- 44. Escape upstream of major aqueducts is usually provided. Canal escapes may be provided at intervals of 15 to 20km for main canal and at 10 to 15km intervals for other canals.