Case cx350 c tier 4 crawler excavator service repair manual
- 1. Printed in U.S.A. Copyright © 2011 CNH America LLC. All Rights Reserved. Case is a registered trademark of CNH America LLC. Racine Wisconsin 53404 U.S.A. Part number 84402832 1st edition English August 2011 SERVICE MANUAL CX350C Tier 4 Crawler Excavator
- 2. Section 1001 Safety, general information and standard torque data 84402832 NA - May 2011
- 3. Safety, general information and standard torque data GENERAL INFORMATION CLEANING Clean all metal parts except bearings, in a suitable cleaning solvent or by steam cleaning. Do not use caustic soda for steam cleaning. After cleaning, dry and put oil on all parts. Clean oil passages with compressed air. Clean bearings in a suitable cleaning solvent, dry the bearings completely and put oil on the bearings. INSPECTION Check all parts when the parts are disassembled. Replace all parts that have wear or damage. Small scoring or grooves can be removed with a hone or crocus cloth. Complete a visual inspection for indications of wear, pitting and the replacement of parts necessary to prevent early failures. BEARINGS Check bearings for easy action. If bearings have a loose fit or rough action replace the bearing. Wash bearings with a suitable cleaning solvent and permit to air dry. DO NOT DRY BEARINGS WITH COMPRESSED AIR. NEEDLE BEARINGS Before you press needle bearings in a bore always remove any metal protrusions in the bore or edge of the bore. Before you press bearings into position put petroleum jelly on the inside and outside diameter of the bearings. GEARS Check all gears for wear and damage. Replace gears that have wear or damage. Oil seals, O-rings and gaskets. Always install new oil seals, O-rings and gaskets. Put petroleum jelly on seals and O-rings. SHAFTS Check all shafts that have wear or damage. Check the bearing and oil seal surfaces of the shafts for damage. SERVICE PARTS Always install genuine Case service parts. When ordering refer to the Parts Catalogue for the correct part number of the genuine Case replacement items. Failures due to the use of other than genuine Case replacement parts are not covered by warranty. LUBRICATION Only use the oils and lubricants specified in the Operator’s or Service Manuals. Failures due to the use of non-specified oils and lubricants are not covered by warranty. 84402832 NA - May 2011 1001-3
- 4. Safety, general information and standard torque data Safety This symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. The message that follows the symbol contains important information about safety. Carefully read the message. Make sure you fully understand the causes of possible injury or death. To prevent injury always follow the Warning, Caution and Danger notes in this section and throughout the manual. Put the warning tag shown below on the key for the key switch when servicing or repairing the machine. One warning tag is supplied with each machine. Additional tags are available from your service parts supplier. WARNING Read the operator's manual to familiarize yourself with the correct control functions. WARNING Operate the machine and equipment controls from the seat position only. Any other method could result in serious injury. WARNING This is a one man machine, no riders allowed. WARNING Before starting engine, study Operator’s Manual safety messages. Read all safety signs on machine. Clear the area of other persons. Learn and practice safe use of controls before operating. It is your responsibility to understand and follow manufacturers instructions on machine operation, ser- vice and to observe pertinent laws and regulations. Operator's and Service Manuals may be obtained from your CASE dealer. WARNING If you wear clothing that is too loose or do not use the correct safety equipment for your job, you can be injured. Always wear clothing that will not catch on objects. Extra safety equipment that can be required includes hard hat, safety shoes, ear protection, eye or face protection, heavy gloves and reflector clothing. WARNING When working in the area of the fan belt with the engine running, avoid loose clothing if possible, and use extreme caution. WARNING When doing checks and tests on the equipment hydraulics, follow the procedures as they are written. DO NOT change the procedure. WARNING When putting the hydraulic cylinders on this machine through the necessary cycles to check operation or to remove air from a circuit, make sure all people are out of the way. WARNING Use insulated gloves or mittens when working with hot parts. 84402832 NA - May 2011 1001-4
- 5. Safety, general information and standard torque data WARNING Lower all attachments to the ground or use stands to safely support the attachments before you do any maintenance or service. WARNING Pin sized and smaller streams of hydraulic oil under pressure can penetrate the skin and result in serious infection. If hydraulic oil under pressure does penetrate the skin, seek medical treatment immediately. Maintain all hoses and tubes in good condition. Make sure all connections are tight. Make a replacement of any tube or hose that is damaged or thought to be damaged. DO NOT use your hand to check for leaks, use a piece of cardboard or wood. WARNING When removing hardened pins such as a pivot pin, or a hardened shaft, use a soft head (brass or bronze) hammer or use a driver made from brass or bronze and a steel head hammer. WARNING When using a hammer to remove and install pivot pins or separate parts using compressed air or using a grinder, wear eye protection that completely encloses the eyes (approved goggles or other approved eye protectors). WARNING Use suitable floor (service) jacks or chain hoist to raise wheels or tracks off the floor. Always block machine in place with suitable safety stands. WARNING When servicing or repairing the machine, keep the shop floor and operator's compartment and steps free of oil, water, grease, tools, etc. Use an oil absorbing material and/or shop cloths as required. Use safe practices at all times. WARNING Some components of this machine are very heavy. Use suitable lifting equipment or additional help as instructed in this Service Manual. WARNING Engine exhaust fumes can cause death. If it is necessary to start the engine in a closed place, remove the exhaust fumes from the area with an exhaust pipe extension. Open the doors and get outside air into the area. WARNING When the battery electrolyte is frozen, the battery can explode if (1), you try to charge the battery, or (2), you try to jump start and run the engine. To prevent the battery electrolyte from freezing, try to keep the battery at full charge. If you do not follow these instructions, you or others in the area can be injured. 84402832 NA - May 2011 1001-5
- 6. Section 2000 Removal and Installation of Engine Assembly 84402832 NA - May 2011
- 7. Removal and Installation of Engine Assembly WARNING • Keep away from fire. • Be sure to release hydraulic pressure before beginning work. • The air conditioner circuit is filled with high- pressure gas, so there is the danger of gas spraying out when loosening lines. • Do not use open flames and do not allow sparks near the battery. CAUTION • Be sure to stop the engine before beginning work. • Be sure to inspect the wire rope and other lifting equipment before beginning work. • Do not stand or pass under the suspended load. Items to prepare • Wrenches (7 mm, 8 mm, 13 mm, 17 mm, 19 mm, 36 mm) • Box wrench (30 mm) • Shackle (with the required lifting capacity) x 2 • Wire ropes (with the required breaking load) • Liftcrane (with the required lifting capacity) • Marking pen • Cap • Plug • Waste oil can • Rag • Cleaning fluid • Wood planks, etc. Removal of Engine Assembly 1. Drain the engine oil.(For details, see "Engine Oil Replacing".) 2. Drain the coolant from the radiator.(For details, see "Removal and Installation of Radiator".) 3. Remove the engine hood.(For details, see "Re- moval and Installation of Engine Hood".) 4. Remove the hydraulic pump.(For details, see "Re- moval and Installation of Hydraulic Pump".) 5. Use a wrench (13 mm) to remove the 3 bolts (1). 84402832 NA - May 2011 2000-3
- 8. Removal and Installation of Engine Assembly 6. Use a wrench (13 mm) to remove the 3 bolts (1), and then remove the bracket (2). 7. Remove the fan guard (1). 8. Use a wrench (8 mm) to loosen the hose band (1) on the radiator, and then remove the upper hose (2). 9. Remove the cushion seal on the side of the radiator, use a wrench (8 mm) to loosen the hose band (1) of the radiator, and then remove the lower hose (2). • Use caps to cover the radiator and hoses to pre- vent the entry of water, dust or dirt. • Before removing the radiator hoses, completely drain the coolant. 10. Use a wrench (13 mm) to loosen the line bolts (1) in 2 locations, and then remove the 2 lines (2) and (3) from the compressor. • Always remove the low-pressure (suction side) line (2) first. • Attach caps or plugs to the compressor and lines to prevent any entry of water, dust or dirt. Tightening torque for bolt installation: 19.6 - 24.5 N•m 84402832 NA - May 2011 2000-4
- 9. Removal and Installation of Engine Assembly 11. Use a wrench (8 mm) to loosen the hose band (1) on the inter cooler, and then remove the hose (2). • Use caps to cover the lines and hoses to prevent the entry of water, dust or dirt. 12. Use a wrench (17 mm) to remove the 5 bolts (1), and then remove the under cover (2). • Use caution when removing as the parts are heavy. Tightening torque for bolt installation: 63.7 - 73.5 N•m 13. Prepare the waste oil can (1). • Drain the engine oil before removing the engine oil hose. 14. Use a wrench (36 mm) to remove the 2 engine oil remote hoses (1). • Mark the engine and hoses so that the connectors match at the time of assembly. • Attach caps or plugs to the engine and hoses to prevent any entry of water, dust or dirt. 84402832 NA - May 2011 2000-5
- 10. Removal and Installation of Engine Assembly • Clean the engine and hoses by spraying them with a parts cleaner to prevent scratches and pre- vent dirt from accumulating on the connectors. 15. Use a wrench (17 mm) to remove the bolt (1), and then remove the battery cable (2) on the negative side. • When removing the terminal and harness, secure them so that they do not interfere with the frame. • Also, cover with a rubber cap to protect against sparks. 16. Use a wrench (17 mm) to remove the 5 bolts (1), and then remove the under cover (2). Tightening torque for bolt installation: 63.7 - 73.5 N•m 17. Use a wrench (8 mm) to remove the 2 nuts (1), and then remove the wiring (2) from the starter motor. 18. Remove the hose band (1), and then remove the fuel hose (2). • Attach caps or plugs to the engine and hoses to prevent any entry of water, dust or dirt. 84402832 NA - May 2011 2000-6
- 11. Removal and Installation of Engine Assembly 19. Remove the hose band (1), and then remove the fuel hose (2). • Attach caps or plugs to the engine and hoses to prevent any entry of water, dust or dirt. 20. Use a wrench (13 mm) to remove the 4 bolts (1), and then remove the box cover (2). 21. Remove the connectors (1) in the box. • Wrap the removed connectors in plastic after tying them together to prevent any entry of water, dust or dirt. 22. Use a wrench (8 mm) to loosen the hose band (1), and then remove the heater hose (2). Attach caps or plugs to the engine and hoses to prevent any entry of water, dust or dirt. 23. Use a wrench (8 mm) to loosen the hose band (1), and then remove the heater hose (2). • Attach caps or plugs to the engine and hoses to prevent any entry of water, dust or dirt. 24. Use a wrench (8 mm) to loosen the hose band (1), and then remove the radiator hose (2). • Use caps to cover the lines and hoses to prevent any entry of water, dust or dirt. 84402832 NA - May 2011 2000-7
- 12. Removal and Installation of Engine Assembly 25. Use a wrench (8 mm) to loosen the hose band (1), and then remove the air hose (2). • Use caps to cover the lines and hoses to prevent any entry of water, dust or dirt. 26. Use a wrench (8 mm) to loosen the hose band (1), and then remove the air hose (2). • Use caps to cover the lines and hoses to prevent any entry of water, dust or dirt. Tightening torque for bolt installation: 8.8 - 9.8 N•m 27. Remove the connectors (1) from the alternator. 28. Remove the cap (1), use the wrench (10 mm) to remove the nut (2), and then remove the alternator wiring (3). 29. Install the 2 shackles (1), and then use the wire rope (2) and liftcrane to secure the engine main unit. 84402832 NA - May 2011 2000-8
- 13. Removal and Installation of Engine Assembly 30. Use a box wrench (30 mm) to remove the 4 bolts (1) from the mount. Tightening torque for bolt installation: 289 - 337 N•m 31. Use the wire rope (1) and liftcrane to lift the engine main unit. Thoroughly check that the location is safe before lowering the engine on wood planks, etc. 84402832 NA - May 2011 2000-9
- 14. Removal and Installation of Engine Assembly Installation of Engine Assembly 1. To install the engine, perform the reverse of the re- moval procedure. Tighten bolts being installed to the specified torque. For bolts for which the torque is not specified, see "Standard Torque Data for Cap Screws and Nuts". After installing the engine, resupply coolant and en- gine oil, perform fuel line air bleeding, and perform filling for the air conditioner gas. For details, see the individual explanations for each procedure. 2. Run the engine at no-load idling and check for any water or oil leaks. 3. Attach the hydraulic pump, covers, and counter- weight. For details, see the individual explanations for each procedure. 84402832 NA - May 2011 2000-10
- 15. Removal and installation of the fuel cooler engine inter-cooler radiator and oil cooler Removal and Installation of Fuel Cooler CAUTION • Be sure to stop the engine before beginning work. • As the fuel hose will be removed, strictly pro- hibit open flames. Items to prepare • Wrench (13 mm) • Screwdriver • Pliers • Marking pen • Cap • Plug • Rag • Cleaning fluid • Drip pan Removal of Fuel Cooler 1. Mark the fuel cooler and hoses (1) and (2) so that the connectors match at the time of assembly. Use pliers to loosen the hose bands (3) and (4), and then remove the hoses. Fuel will spill out, so place a drip pan directly below the area. Attach caps or plugs to the fuel cooler and hoses to prevent any entry of water, dust or dirt. 2. Use a wrench (13 mm) to remove the 4 bolts (1), and then remove the fuel cooler (2). Installation of Fuel Cooler To installation, perform the reverse of the removal pro- cedure. After connecting the hoses, carefully check for any fuel leaks. Tighten bolts being installed to the specified torque. For bolts for which the torque is not specified, see "Stan- dard Torque Data for Cap Screws and Nuts". 84402832 NA - May 2011 2001-3
- 16. Removal and installation of the fuel cooler engine inter-cooler radiator and oil cooler Removal and Installation of Engine Inter Cooler CAUTION • Be sure to stop the engine before beginning work. • As the fuel hose will be removed, strictly pro- hibit open flames. Items to prepare • Wrenches (8 mm, 13 mm) • Flathead screwdriver • Wire cutters • Cap • Rag • Cleaning fluid Removal of Inter Cooler 1. Remove the fuel cooler.(For details, see "Removal and Installation of Fuel Cooler".) Use a wrench (13 mm) to remove the 4 bolts (1), and then remove the bracket (2) from the fuel cooler. 2. Use a wrench (8 mm) or flathead screwdriver to loosen the hose bands (1) in the 2 locations, and then remove the 2 hoses (2) and (3). Use caps to cover the inter cooler and hoses to pre- vent the entry of water, dust or dirt. 3. Use a wrench (13 mm) to remove the 4 bolts (1), and then remove the inter cooler (2). 84402832 NA - May 2011 2001-4
- 17. Removal and installation of the fuel cooler engine inter-cooler radiator and oil cooler Installation of Inter Cooler To install, perform the reverse of the removal procedure. Check for any air leaks. Tighten bolts being installed to the specified torque. For bolts for which the torque is not specified, see "Stan- dard Torque Data for Cap Screws and Nuts". Removal and Installation of Radiator WARNING • Do not remove the radiator cap when the ra- diator coolant temperature is high. Hot liquid could spray out. CAUTION • Be sure to release hydraulic pressure before beginning work. • Be sure to stop the engine before beginning work. • Be sure to inspect the wire rope and other lifting equipment before beginning work. • Do not stand or pass under the suspended load. Items to prepare • Wrenches (8 mm, 14 mm, 19 mm) • Box wrenches (8 mm, 10 mm) • Pliers • Shackle (with the required lifting capacity) x 2 • Wire ropes (with the required breaking load) • Liftcrane (with the required lifting capacity) • Caps • Plugs • Drain tank • Drain hose • Rag • Cleaning fluid • Wood planks, etc. 84402832 NA - May 2011 2001-5
- 18. Removal and installation of the fuel cooler engine inter-cooler radiator and oil cooler Removal of Radiator 1. Use a wrench (19 mm) to remove the 5 bolts (1), and then remove the under cover (2). 2. Install the drain hose (1), and then prepare the drain tank (2). 3. To make it easier to drain the coolant, remove the radiator cap (1). 4. Loosen the drain plug (1), and then drain the coolant. 5. Use a wrench (8 mm) to loosen the hose band (1), and then remove the hose (2). • Use caps to cover the lines and hoses to prevent any entry of water, dust or dirt. 6. Use a box wrench (13 mm) to remove the 1 nut (1) and the 3 bolts (2) of the radiator cover. 84402832 NA - May 2011 2001-6
- 19. Removal and installation of the fuel cooler engine inter-cooler radiator and oil cooler 7. Use a wrench (8 mm) to loosen the hose band (1) on the radiator, and then remove the upper hose (2). 8. Remove the cushion seal on the side of the radiator, use a wrench (8 mm) to loosen the hose band (1) of the radiator, and then remove the lower hose (2). • Use caps to cover the radiator and hoses to pre- vent the entry of water, dust or dirt. • Before removing the radiator hoses, completely drain the coolant. 9. Remove the drain plug (1), loosen the hose band (2), and then remove the hose (3). 10. Loosen the hose band (2), and then remove the hose (1) from the radiator cap. • Attach caps or plugs to the hoses to prevent any entry of water, dust or dirt. 11. Use a wrench (13 mm) to remove the 3 bolts (1). 84402832 NA - May 2011 2001-7
- 20. Removal and installation of the fuel cooler engine inter-cooler radiator and oil cooler 12. Use a wrench (13 mm) to remove the 3 bolts (1), and then remove the bracket (2) 13. Remove the fan guard (1). 14. Remove the 2 butterfly bolts (1), and then remove the front anti-insect net (2). 15. Install the 2 shackles (1) to the top of the radiator, and then use the wire rope (2) and liftcrane to lift the radiator. 84402832 NA - May 2011 2001-8
- 21. Removal and installation of the fuel cooler engine inter-cooler radiator and oil cooler 16. Lift the radiator together with the radiator cover (2) until the fixtures (1) at the bottom of the radiator become disconnected. 17. Thoroughly check that the location is safe before lowering the radiator on square wooden pieces. When laying down the radiator, be careful not to bend or crush the bottom fixtures (1). Installation of radiator To install, perform the reverse of the removal procedure. Tighten bolts being installed to the specified torque. For bolts for which the torque is not specified, see "Stan- dard Torque Data for Cap Screws and Nuts". For details on the method for coolant filling, see the (Ser- vice Text Procedures for Replacing Consumable Parts • Radiator Coolant Replacement). Coolant capacity is 30 L. Finally, check that the level of coolant is correct. 84402832 NA - May 2011 2001-9
- 22. Removal and installation of the fuel cooler engine inter-cooler radiator and oil cooler Removal and Installation of Oil Cooler WARNING • Keep away from fire. CAUTION • Be sure to stop the engine before beginning work. • Be sure to inspect the wire rope and other lifting equipment before beginning work. • Do not stand or pass under the suspended load. Items to prepare • Wrenches (17 mm, 19 mm) • Hexagon wrench (10 mm) • Pliers • Screwdriver • Eyebolts (M12 x 2) • Shackle (with the required lifting capacity) x 2 • Wire rope (with the required breaking load) • Liftcrane (with the required lifting capacity) • Caps • Waste oil can • Rag • Cleaning fluid • Wood planks, etc. Removal of oil cooler 1. Drain the hydraulic oil from the hydraulic oil tank. See "Draining Oil from Hydraulic Oil Tank" for de- tails of the procedure. 2. Use a wrench (19 mm) to remove the 5 bolts (1), and then remove the under cover (2). 3. Prepare the waste oil can (1). 4. Remove the 4 butterfly bolts (1), and then remove the anti-insect net (2). 84402832 NA - May 2011 2001-10
- 23. Removal and installation of the fuel cooler engine inter-cooler radiator and oil cooler 5. Use a wrench (19 mm) to remove the 7 bolts (1) and bracket (2), and then remove the seal cushion. 6. Use a hexagon wrench (10 mm) to remove the 2 upper hexagon socket head bolts (6) and 2 lower bolts (6), and then remove the lines (7) and (8). • Use caps to cover the oil cooler and lines to pre- vent the entry of water, dust or dirt. 7. Use a wrench (13 mm) to remove the 5 bolts (1). 84402832 NA - May 2011 2001-11
- 24. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
- 25. Removal and installation of the fuel cooler engine inter-cooler radiator and oil cooler 8. Install the 2 eyebolts (M12) (10) on the top of the oil cooler. • Fully tighten the eyebolts, and then loosen them by a half turn. 9. Install the 2 shackles (11) to the eyebolts, and then use the wire rope (12) and liftcrane to lift the oil cooler main unit. 10. Thoroughly check that the location is safe before lowering the oil cooler on wood planks, etc. Installation of oil cooler To install, perform the reverse of the removal procedure. Tighten bolts being installed to the specified torque. For bolts for which the torque is not specified, see "Stan- dard Torque Data for Cap Screws and Nuts". 84402832 NA - May 2011 2001-12
- 26. Removal and Installation of Turbo Charger WARNING The engine is extremely hot just after stopping. Wait for them to sufficiently cool before begin- ning work. CAUTION • Be sure to stop the engine before beginning work. Items to prepare • Wrenches (8 mm, 10 mm, 13 mm, 17 mm) • Cap • Plug • Rag • Cleaning fluid Removal of Turbo Charger 1. Battery ground cable Disconnect 1) Disengage the battery ground cable from the battery. 2. Coolant Drain 1) Drain the coolant from the radiator. CAUTION • After the coolant is discharged, make sure to tighten the drain plug. 3. Turbocharger assembly Removal 1) Remove the air cleaner duct from the air cleaner assembly and the turbocharger as- sembly. 2) Remove the air intake hose from the tur- bocharger assembly and the intercooler. 3) Remove the exhaust pipe from the tur- bocharger. 4) Disengage the oil feed pipe from the tur- bocharger assembly. ANNOTATION: • Remove the clip. 5) Disengage the oil return pipe from the tur- bocharger assembly. 6) Disengage the water return pipe from the tur- bocharger assembly. 7) Disengage the water feed pipe from the tur- bocharger assembly. ANNOTATION: • Remove the clip. 8) Disengage the harness connector from the turbocharger assembly. 9) Remove the turbocharger assembly from the exhaust manifold. 1 Oil feed pipe 2 Clip 3 Oil return pipe 4 Water feed pipe 5 Water return pipe 84402832 NA - May 2011 2004-3
- 27. Removal and Installation of Turbo Charger Installation of Turbo Charger 1. Turbocharger assembly Installation 1) Replenish the engine oil with the turbocharger assembly. 2) Align the gasket to the turbocharger assem- bly. 3) Install the turbocharger assembly to the ex- haust manifold. Tightening torque： 52 N・m { 5.3 kgf・m / 38 lb・ft } 4) Connect the water feed pipe to the tur- bocharger assembly. Tightening torque： 41 N・m { 4.2 kgf・m / 30 lb・ft } CAUTION • Use a new gasket. 5) Connect the water return pipe to the tur- bocharger assembly. Tightening torque： 41 N・m { 4.2 kgf・m / 30 lb・ft } CAUTION • Use a new gasket. 6) Connect the oil return pipe to the turbocharger assembly. Tightening torque： 24 N・m { 2.4 kgf・m / 17 lb・ft } CAUTION • Use a new gasket. 7) Connect the oil feed pipe to the turbocharger assembly. Tightening torque： 34 N・m { 3.5 kgf・m / 25 lb・ft } Tightening torque： 24 N・m { 2.4 kgf・m / 17 lb・ft } Clip CAUTION • Use a new gasket. 1 Oil feed pipe 2 Clip 3 Oil return pipe 4 Water feed pipe 5 Water return pipe 8) Install the exhaust pipe to the turbocharger assembly. 9) Install the air intake hose to the turbocharger assembly and the intercooler. 10) Install the air cleaner duct to the air cleaner assembly and the turbocharger assembly. 2. Coolant Filling 1) Loosen the valve using a wrench. 2) Replenish the coolant with the radiator. CAUTION • Be careful not to let coolant over- flow splash on the exhaust system parts. Coolant overflow should be wiped off. 3) Tighten the valve using a wrench. CAUTION • Use new gaskets. Tightening torque： 22 N・m { 2.2 kgf・m / 16 lb・ft } 84402832 NA - May 2011 2004-4
- 28. Removal and Installation of Turbo Charger 4) Replenish the coolant with the radiator. 1 Valve 2 Gasket 5) Battery ground cable Connect 1) Connect the battery ground cable to the battery. 84402832 NA - May 2011 2004-5