CASE CX39B Hydraulic Mini Excavator Service Repair Manual.pdf

TO THE READER
This manual has been printed for a skilful engineer
to supply the necessary technical information to
carry out service operations on this machine.
Carefully read this manual to obtain correct infor-
mation regarding repair procedures.
For any question or remark, or in case of any error
in the contents of this manual, please contact:
CNH ITALIA S.p.A.
Via Plava, 80
10135 TORINO - Italy
REFERENCE
Beyond this Service Manual, also refer to the doc-
uments listed below:
- Operator’s Manual
- Parts Catalogue
COMPLETE SERVICE MANUAL
The Service Manual consists of one volume:
- CX35B - CX39B - Service Manual “Hydraulic
Mini Excavators”
The Service Manual for “Hydraulic Mini Excava-
tors” contains the necessary technical information
to carry out maintenance and repair operations on
the machine, the necessary tools to carry out
maintenance operations, the information on serv-
ice standards, the procedures for removal, instal-
lation, disassembly and reassembly.
The Service Manual relevant to the excavator
models CX35B - CX39B consists in the following
volume, which is identified through the relevant
print no. as reported below:
VOLUME MACHINE TYPE PRINT NUMBER
Service Manual for “Hydraulic Mini Excavators” CX35B
CX39B
84553645A

SAFETY PRECAUTIONS
0-2
GENERAL SAFETY INFORMATION
WARNING
Do not operate or perform any maintenance on this
machine until all instructions found in the OPERA-
TOR’S MANUAL have been thoroughly read and
understood.
Improper operation or maintenance of this machine
may cause accidents and could result in serious in-
jury or death.
Always keep the manual in storage.
If it is missing or damaged, place an order with an
authorized dealer/distributor for a replacement.
If you have any questions, please consult an au-
thorized dealer/distributor.
(1) Most accidents occurring during operation are due
to negligence of precautionary measures and safety
instructions. Sufficient care should be taken to avoid
these accidents. Erroneous operation, lubrication or
maintenance services are very dangerous and may
cause injury or death of personnel. Therefore all
precautionary measures, NOTES, DANGERS,
WARNINGS and CAUTIONS contained in this man-
ual and on the machine should be read and under-
stood by all personnel before starting any work with
or on the machine.
(2) Operation, inspection, and maintenance should be
carefully carried out, and first priority must be given
to safety. Messages of safety are indicated with
marks. The safety information contained in this
manual is intended only for supplement of safety
codes, insurance requirements, local laws, rules
and regulations.
(3) Messages of safety appear in the manual and on
the machine: All messages of safety are identified
by the words “DANGER”, “WARNING” and “CAU-
TION”.
1) DANGER- Indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury and is represented as
follows:
DANGER
2) WARNING- Indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury and is represented as
follows:
WARNING
3) CAUTION- Indicates a potentially hazardous
situation which, if not avoided, may result in mi-
nor or moderate injury. It may also be used to
alert against possible damage to the machine
and its components and is represented as fol-
lows:
CAUTION
(4) It is very difficult to forecast every danger that may
occur during operation. However, safety can be
guaranteed by fully understanding the operating
procedures for this machine according to the meth-
ods recommended by the Manufacturer.
(5) While operating the machine, be sure to perform
work with great care, so as not to damage the ma-
chine, or allow accidents to occur.
(6) Continue studying this manual until all Safety, Oper-
ation and Maintenance procedures are completely
understood by all persons working with the ma-
chine.

SAFETY PRECAUTIONS
0-3
SAFETY PRECAUTIONS
WARNING
The proper and safe lubrication and maintenance
for this machine, recommended by Manufacturer,
are outlined in the OPERATOR’S MANUAL for the
machine.
Improper performance of lubrication or mainte-
nance procedures are dangerous and could result
in injury or death. Read and understand the MANU-
AL before performing any lubrication or mainte-
nance.
The serviceman or mechanic may be unfamiliar
with many of the systems on this machine. This
makes a careful use of the systems very important
when performing maintenance operations. Sound
knowledge of the system and or components is im-
portant before the removal or disassembly of any
component.
Because of the size of some of the machine compo-
nents, the serviceman or mechanic should check the
weights noted in this manual. Use proper lifting proce-
dures when removing any components. Weight of com-
ponents table is shown in the section: TECHNICAL
SPECIFICATIONS.
The following is a list of basic precautions that must al-
ways be observed.
(1) Read and understand all Warning plates and de-
cals on the machine before Operating, Maintain-
ing or Repairing this machine.
(2) Always wear protective glasses and protective
shoes when working around machines. In particu-
lar, wear protective glasses when using hammers,
punches or drifts on any part of the machine or at-
tachments. Use welders gloves, hood/goggles,
apron and the protective clothing appropriate to
the welding job being performed. Do not wear
loose fitting or torn clothing. Remove all rings from
fingers, loose jewellery, confine long hair and
loose clothing before working on this machinery.
(3) Disconnect the battery and hang a “Maintenance
in Progress” tag in the operator’s seat. Remove
starter key.
(4) If possible, make all repairs with the machine
parked on a level and firm surface. Block the ma-
chine so it does not roll while working on or under
the machine. Hang a “Maintenance in Progress”
tag in the operator’s seat.
(5) Do not work on any machine that is supported only
by lift, jacks or a hoist. Always use blocks or stops
for the jack before carrying out any disassembly
operation.
WARNING
Do not operate this machine unless you have read
and understood all instructions contained in this
manual. Improper machine operation is dangerous
and could result in injury or death.
(6) Relieve all pressure in air, oil or water systems be-
fore any lines, fittings or related items are discon-
nected or removed. Always make sure all raised
components are blocked correctly and be alert for
possible pressure when disconnecting any device
from a system under pressure.
(7) Lower the bucket, dozer or other attachments to the
ground before performing any work on the ma-
chine. If this cannot be done, make sure the buck-
et, blade or other attachment is blocked correctly
to prevent it from dropping unexpectedly.
(8) Use steps and grab handles when mounting or
dismounting a machine. Remove any debris or
mud from steps, walkways or work platforms be-
fore using them. Always face the machine when
using steps, ladders and walkways. When it is not
possible to use the designed access system, pro-
vide ladders, scaffolds, or work, platforms to per-
form safe repair operations.
(9) To avoid back injury, use a hoist when lifting com-
ponents which weigh 20 kg or more. Make sure
all chains, hooks, slings, etc., are in good condi-
tion and are the correct capacity. Be sure hooks
are positioned correctly. Lifting eyes are not to be
side loaded during a lifting operation.
(10) To avoid burns, be alert for hot parts and surfaces
immediately after stopping the machine such as
hot fluids in lines, tubes and compartment covers.
(11) Be careful when removing cover plates. Gradually
back off the last two capscrews or nuts located at
opposite ends of the cover or device and carefully
pry the cover loose to relieve any spring or other
pressure, before removing the last two capscrews
or nuts completely.

SAFETY PRECAUTIONS
0-4
(12) Be careful when removing filler caps, breathers
and plugs on the machine. Hold a rag over the cap
or plug to prevent being sprayed or splashed by
liquids under pressure. Danger is even greater if
the machine has just been stopped, as liquids
might be boiling hot.
(13) Always use the proper tools that are in good con-
dition and that are suited for the job at hand. Be
sure you understand how to use them before per-
forming any service work.
(14) Reinstall all clamps with the same spare part
number. Do not use clamps of inferior quality if re-
placement is necessary.
(15) Repairs which require welding should be per-
formed only with the benefit of the appropriate ref-
erence information and by personnel adequately
trained and skilled in welding procedures. Deter-
mine the type of metal being welded and select
the correct welding procedure and electrodes,
rods or wires to provide a metal weld strength at
least equivalent to that of the parent metal. Make
sure to disconnect the battery before any welding
operation is performed.
(16) Do not damage wiring during removal operations.
Reinstall the wiring so it is not damaged nor will be
damaged in operation of the machine by contact-
ing sharp corners, or by rubbing against some ob-
ject or hot surface. Do not connect wiring to a line
containing fluid.
(17) Be sure all protective devices, including guards
and shields, are properly installed and functioning
correctly before starting a repair. If a guard or
shield must be removed to perform the repair
work, use extra caution and replace the guard or
shield after repair is complete.
(18) Performing maintenance and repair operations
while the bucket is lifted is dangerous, because
there is the possibility of a device falling. Do not
fail to lower such device and place the bucket to
the ground before starting the operation.
(19) Loose or dirty fuel, lubrication and hydraulic sys-
tems, pipes and hoses may cause fires. Do not
bend or strike high-pressure lines, do not install
bent or damaged lines. Inspect lines, tubes and
hoses carefully. Do not check for leaks with your
hands. Very small (pinhole) leaks can result in a
high velocity oil jet that will be invisible close to the
hose.
This oil can penetrate the skin and cause personal
injury. Use card-board or paper to locate pinhole
leaks.
(20) Tighten connections to the correct torque. Make
sure that all protections against burns, the clamps
and the operator’s protective devices are correctly
installed in order to prevent excessive heat, vibra-
tions or rubbing against other parts during opera-
tion. Shields that protect against oil spray onto hot
exhaust components in event of a line, tube or
seal failure must be installed correctly.
(21) Do not operate a machine if any rotating part is
damaged or contacts any other part during opera-
tion. Any high speed rotating component that has
been damaged or altered should be checked for
balance before reusing.
(22) Be careful when servicing or separating the
tracks. Chips can fly when removing or installing a
track pin. Wear safety glasses and long sleeve
protective clothing. Tracks can unroll very quickly
when separated. Keep away from front and rear of
machine. The machine can move unexpectedly
when both tracks (crawlers) are disengaged from
the sprockets. Block the machine to prevent it
from moving.

SAFETY PRECAUTIONS
0-5
TABLE OF CONTENTS CX35B
CX39B
Title Table of
Contents
No.
SPECIFICATIONS
DESCRIPTION 1
SPECIFICATIONS 2
ATTACHMENT DIMENSIONS 3
MAINTENANCE
TOOLS 11
MAINTENANCE STANDARDS AND TEST PROCEDURES 13
SYSTEMS
HYDRAULIC SYSTEM 22
ELECTRICAL SYSTEM 23
SYSTEMS COMPONENTS 24
DISASSEMBLY
GENERAL DISASSEMBLY AND ASSEMBLY 31
ATTACHMENT 32
SLEWING UPPER STRUCTURE 33
TRAVEL SYSTEM 34
TROUBLESHOOTING
TROUBLESHOOTING (HYDRAULIC SYSTEM) 42
TROUBLESHOOTING (ELECTRICAL SYSTEM) 43
TROUBLESHOOTING (ENGINE) 44
E/G
ENGINE 51
OPT
AIR CONDITIONING SYSTEM 61
OBJECT HANDLING SYSTEM 62
DATA
SUPPORTING DATA 71

1. DESCRIPTION
TABLE OF CONTENTS
1.1 GENERAL PRECAUTIONS FOR REPAIRS .....................................................1-1
1.1.1 PREPARATION BEFORE DISASSEMBLING ..............................................1-1
1.1.2 SAFETY IN DISASSEMBLING AND ASSEMBLING ....................................1-1
1.1.3 DISASSEMBLING AND ASSEMBLING HYDRAULIC EQUIPMENT ............1-1
1.1.4 ELECTRICAL EQUIPMENT ..........................................................................1-2
1.1.5 HYDRAULIC PARTS .....................................................................................1-3
1.1.6 WELDING REPAIR .......................................................................................1-3
1.1.7 ENVIRONMENTAL MEASURE .....................................................................1-3
1.2 INTERNATIONAL UNIT CONVERSION SYSTEM (BASED ON MARKS’
STANDARD HANDBOOK FOR MECHANICAL ENGINEERS) ........................1-4

1. DESCRIPTION
1-1
1.1 GENERAL PRECAUTIONS FOR
REPAIRS
1.1.1 PREPARATION BEFORE DISASSEMBLING
(1) Understanding operating procedure
Read OPERATION AND MAINTENANCE MANU-
AL carefully to understand the operating procedure.
(2) Cleaning machines
Remove soil, mud, and dust from the machine be-
fore carrying it into the service shop to prevent loss
of work efficiency, damage of parts, and difficulty in
rust prevention and dust protection while reassem-
bling.
(3) Inspecting machines
Identify the parts to be disassembled before start-
ing work, determine the disassembling procedure
by yourself considering the workshop situations
etc., and request procurement of necessary parts in
advance.
(4) Recording
Record the following items for communication and
prevention of recurring malfunction.
1) Inspection date and place.
2) Model name, applicable machine number, and
hourmeter read.
3) Trouble condition, place and cause.
4) Visible oil leakage, water leakage and damage.
5) Clogging of filters, oil level, oil quality, oil con-
tamination and loosening of connections.
6) Result of consideration if any problem exists based
on the operation rate per month calculated from
hourmeter indication after the last inspection date.
(5) Arrangement and cleaning in service shop
1) Tools required for repair work.
2) Prepare space to place the disassembled parts.
3) Prepare oil containers for draining oil etc.
1.1.2 SAFETY IN DISASSEMBLING AND
ASSEMBLING
(1) Wear appropriate clothes with long sleeves, safety
shoes, safety helmet and protective glasses.
(2) Suspend warning tag “DO NOT OPERATE” from the
doorknob or the operating lever, and have a preliminary
meeting before starting work.
(3) Stop the engine before starting inspection and
maintenance to prevent the operator being caught
in machine.
(4) Identify the location of a first-aid kit and a fire extin-
guisher, and also where to make contact in a state
of emergency.
(5) Choose a hard, level and safe place, and place the
attachment on the ground securely.
(6) Use a lifter such as a crane to remove heavy parts (20 kg
or more) from the machine.
(7) Use proper tools, and replace or repair defective
tools.
(8) Support the machine and attachment with supports
or blocks if the work is performed in the lifted condi-
tion.
1.1.3 DISASSEMBLING AND ASSEMBLING
HYDRAULIC EQUIPMENT
(1) Removing hydraulic equipment
1) Before disconnecting pipes, release the hy-
draulic pressure of the system, or open the re-
turn side cover and take out the filter.
2) Carefully drain oil of the removed pipes into a
containers without spilling on the floor.
3) Apply plugs or caps on the pipe ends to avoid
oil spillage and dust intrusion.
4) Clean off the external surface of the equipment be-
fore disassembling, and drain hydraulic and gear oil
before placing it on the workbench.
(2) Disassembling hydraulic equipment
1) Do not disassemble, reassemble or modify the
hydraulic equipment without the permission of
the manufacturer, who is not responsible for the
performance and function of the product after
modification.
2) When disassembling and reassembling for unavoid-
able reason, refer the work to qualified personnel
who have the specific knowledge or completed the
parts service training.
3) Provide matching marks to facilitate reassem-
bling work.
4) Before starting the work, read the manual of disas-
sembling procedure, if it is provided, and decide
whether the work can be performed by yourself.

1. DESCRIPTION
1-2
5) Use the special jig and tools without fail if they
are specified.
6) If it is hard to remove a part according to the
procedure, do not try it by force but investigate
the cause.
7) Place the removed parts in order and attach
tags to facilitate the reassembling.
8) Note the location and quantity of parts com-
monly applied to multiple locations.
(3) Inspecting parts
1) Ensure that the disassembled parts are free from
seizure, interference and uneven contact.
2) Measure and record wear condition of parts
and clearance.
3) If the problem is found in a part, repair or re-
place it with a new one.
(4) Reassembling hydraulic equipment
1) Turn ON the ventilation fan or open windows to
maintain good ventilation prior to starting the
cleaning of parts.
2) Perform rough and finish cleaning before assem-
bling.
3) Remove washing oil by air and apply clean hy-
draulic or gear oil for assembling.
4) Always replace the removed O-rings, backup
rings and oil seals with new ones by applying
grease in advance.
5) Remove dirt and moisture from and perform de-
greasing on the surface where liquid gasket to
be applied.
6) Remove rust preventive agent from the new
parts before use.
7) Fit bearings, bushings and oil seals using spe-
cial jigs.
8) Assemble the parts utilizing matching marks.
9) Ensure all the parts are completely assembled
after the work.
(5) Installing hydraulic equipment
1) Ensure hydraulic oil and lubricant are properly
supplied.
2) Perform air bleeding when:
1. Hydraulic oil changed
2. Parts of suction side piping replaced
3. Hydraulic pump installed
4. Slewing motor installed
5. Travel motor installed
6. Hydraulic cylinder installed
WARNING
Operation of the hydraulic equipment with-
out filling hydraulic oil or lubricant or with-
out performing air bleeding will result in
damage to the equipment.
3) Perform air bleeding of the hydraulic pump and
slewing motor after loosening the upper drain
plug, starting the engine and keep it in low idle
condition.
Complete the air bleeding when seeping of hy-
draulic oil is recognized, and tightly plug.
4) Perform air bleeding of the travel motor and the
hydraulic cylinders by running the engine for more
than 5 minutes at low speed without load.
WARNING
Do not allow the hydraulic cylinder to bottom
on the stroke end just after the maintenance.
5) Perform air bleeding of pilot line by performing
a series of digging, slewing and travel.
6) Check hydraulic oil level after placing the at-
tachment to the oil check position, and replen-
ish oil if necessary.
1.1.4 ELECTRICAL EQUIPMENT
(1) Do not disassemble electrical equipment.
(2) Handle it carefully not to drop and give a shock.
(3) Turn the key OFF prior to connecting and discon-
necting work.
(4) Disconnect the connector by holding it and press-
ing the lock. Do not pull the wire to apply force to the
caulking portion.
(5) Connect the connector and ensure it is completely
locked.
(6) Turn the key OFF prior to touching the terminal of
starter or generator.
(7) Remove the ground (earth) terminal of battery
when handling tools around the battery or its relay.
(8) Do not splash water on the electrical equipment
and connectors during machine washing.
(9) Check for moisture adhesion inside the waterproof
connector after pulling it out, since it is hard to re-
move moisture from the connector.

1. DESCRIPTION
1-3
If moisture adhesion is found, dry it completely be-
fore the connection.
WARNING
Battery electrolyte is hazardous.
Battery electrolyte is dilute sulfuric acid. Exposure
of skin or eyes to this liquid will cause burning or
loss of eyesight.
If this occurs, take the following measures and get
prompt specialised medical attention.
• When skin exposed:
Wash with water and soap sufficiently.
• When eyes exposed:
Immediately wash away with city water continu-
ously for more than 10 minutes.
• When a large amount of the liquid flows out:
Neutralize with sodium bicarbonate or wash
away with city water.
• When swallowed:
Drink a large amount of milk or water.
• When clothes exposed:
Immediately undress and wash.
1.1.5 HYDRAULIC PARTS
(1) O-ring
• Ensure O-rings have elasticity and are not dam-
aged before use.
• Use the appropriate O-rings. O-rings are of dif-
ferent kinds and made of different materials,
and they have a different hardness to be ap-
plied to a variety of parts, such as moving or
fixed parts, subject to high pressure and ex-
posed to corrosive fluids, even if their size is
same.
• Fit the O-rings without distortion and bend.
• Always handle floating seals as a pair.
(2) Flexible hose (F hose)
• Use the appropriate parts. Different parts are
used depending on the working pressure even
the size of fitting and the total length of the hose
is same.
• Tighten the fitting at the specified torque.
Ensure no kink, tension, interference nor oil
leakage is recognized.
1.1.6 WELDING REPAIR
(1) Refer repair welding to qualified personnel accord-
ing to the appropriate procedure.
(2) Disconnect the ground (earth) cable of the battery
before starting the repair.
Failure to do so will cause damage to the electrical
equipment.
(3) Move away the articles in advance that may cause
fire if exposed to sparks.
(4) Before starting the repair of the attachment, do not
fail to cover the plated surface of the piston rod with
flameproof sheet to prevent it from being exposed
to sparks.
1.1.7 ENVIRONMENTAL MEASURE
(1) Run the engine at the place that is sufficiently ven-
tilated.
(2) Industrial waste disposal
Dispose of the following parts according to the rel-
evant regulations:
Waste oil and waste container
Battery
(3) Precautions for handling hydraulic oil
Exposure of eyes to hydraulic oil will cause inflam-
mation. Wear protective glasses before handling to
avoid an accident. If an eye is exposed to the oil,
take the following emergency measures:
• When an eye exposed:
Immediately wash away with city water suffi-
ciently till stimulative feeling vanishes.
• When swallowed:
Do not let vomit, and receive medical treatment
immediately.
• When skin exposed:
Wash with water and soap sufficiently.
(4) Others
Use replacement parts and lubricants authorized as
the genuine parts.

1. DESCRIPTION
1-4
1.2 INTERNATIONAL UNIT
CONVERSION SYSTEM
(BASED ON MARKS’
STANDARD HANDBOOK FOR
MECHANICAL ENGINEERS)
Introduction
Although this manual includes International System of
Unit and Foot-Pound System of Units, if you need SI
unit, refer to the following international system of units.
Given hereinafter is an except of the units that are re-
lated to this manual.
1. Etymology of SI Unites
French: Système International d’Unités
English: International System of Units
2. Construction of SI Unit System
(1) Base units
(2) Supplementary units
(3) Derived Units
(4) Derived units bearing peculiar designations
Table 1-1
QUANTITIES UNIT MARK
Length meter m
Mass Kilogram kg
Time second s
Electric current Ampère A
Thermodynamic
temperature
Kelvin K
Amount of
substance
mol mol
Luminous
intensity
candela cd
Table 1-2
Plane angle radiant rad
Solid angle steradian sr
Base units
Derived units of
base units
Supplementary
units
Derived units
Derived units bearing
peculiar designations
Prefixes of SI
(n-th power of 10, where n is an integer)
SI unit
system
SI units
Table 1-3
Area square meter m2
Volume cubic meter m3
Speed metres per second m/s
Acceleration metres per square second m/s2
Density kilogram per cubic meter kg/m3
Table 1-4
QUANTITIES UNIT MARK FORMULA
Frequency Hertz Hz 1/s
Force Newton N kg • m/s2
Pressure and
stress
Pascal Pa N/m2
Energy, Work
and Quantity of
heat
Joule J Nm
Power Watt W J/s
Quantity of
electricity
Coulomb C A•s
Potential
difference,
voltage and
electromotive
force
Volt V W/A
Quantity of
static
electricity and
electric
capacitance
Farad F C/V
Electric
resistance
Ohm V/A
Celsius
temperature
Celsius
degree or
degree C
(t+273.15)K
Luminous
intensity
lux lx lm/m2

1. DESCRIPTION
1-5
(5) Prefixes of SI
(6) Unit Conversion
Table 1-5
PREFIX MARK MULTIPLICATION FACTORS
giga G 109
mega M 106
kilo k 103
hecto h 102
deca da 10
deci d 10–1
centi c 10–2
milli m 10–3
micro µ 10–6
nano n 10–9
pico p 10–12
Table 1-6
QUANTITIES Gravitational SI CONVERSION FACTOR
Mass kg kg
Force kgf N 1 kgf = 9.807 N
Torque kgf•m Nm kgf•m = 9.807 Nm
Pressure kgf/cm2
MPa 1 kgf/cm2
= 0.09807 MPa
Motive Power PS kW 1 PS = 0.7355 kW
Revolution rpm min-1
rpm

2. SPECIFICATIONS
TABLE OF CONTENTS
2.1 COMPONENTS NAME .....................................................................................2-1
2.2 MACHINE DIMENSIONS ..................................................................................2-2
2.3 SPECIFICATIONS AND PERFORMANCE .......................................................2-4
2.4 MACHINE AND COMPONENTS WEIGHT (DRY) ............................................2-5
2.5 TRANSPORTATION .........................................................................................2-7
2.6 CRAWLER TYPE ..............................................................................................2-9
2.7 TYPE OF BUCKET ...........................................................................................2-9
2.8 ENGINE SPECIFICATIONS ............................................................................2-11
2.8.1 SPECIFICATIONS ......................................................................................2-11
2.8.2 ENGINE PERFORMANCE CURVE ............................................................2-12
2.9 LUBRICANT, FUEL AND COOLANT SPECIFICATIONS ...............................2-13

2. SPECIFICATIONS
2-1
2.1 COMPONENTS NAME
No. NAME No. NAME No. NAME No. NAME
1 Engine 2 Oil screen 3 Radiator 4 Expansion tank
5 Air cleaner 6 Muffler 7 Fuel tank 8 Hydraulic oil tank
9 Hydraulic pump 10 Slewing motor 11 Swing cylinder 12 Control valve
13 Travel lever 14 Safety lever lock 15 Canopy 16 Operating lever
17 Dozer control lever 18 Throttle lever 19 Gauge cluster
20 Battery 21 Rotary control valve 22 Travel motor 23 Slewing bearing
24 Idler adjust 25 Lower roller 26 Upper roller 27 Rubber belt
28 Dozer 29 Dozer cylinder 30 Boom 31 Boom cylinder
32 Arm cylinder 33 Lights 34 Arm 35 Link rod and idler link
36 Bucket cylinder 37 Bucket
11
28
27
24
25
26
22
32 33
30
31
12
36
34
35
37
1
2
8
16
17
18
19
3
4
5
6
15
7
20
21
9
10
13
14
23
29

2. SPECIFICATIONS
2-2
2.2 MACHINE DIMENSIONS
Unit: mm
(1) CX35B (CANOPY)
(2) CX35B (CAB)
345
(13.6")
345
2550
2000
1540
570
2570
1550 (5’1.0")
1550
775
1380
1840
4390
1550
300
1250
1550
330
R775
85
50
660
1550
660
185
2550
2000
1540
570
2570
775
1380
1840
4390
1550
300
1250
1550
330
R775
85
50
660
660
1550
345
(13.6")
345
185
1550

2. SPECIFICATIONS
2-3
Unit: mm
(3) CX39B (CANOPY)
(4) CX39B (CAB)
2680
2150
1700
570
2570
850
1460
1910
4710
1550
300
1400
1700
330
R850
60
50
1700
660
660
345
(13.6")
345
160
1600
2680
2150
1700
570
2570
850
1460
1910
4710
1550
300
1400
1700
330
R850
60
50
660
660
1700
345
(13.6")
345
160
1600

2. SPECIFICATIONS
2-4
2.3 SPECIFICATIONS AND PERFORMANCE
SPEED AND GRADEABILITY
ENGINE
HYDRAULIC COMPONENTS
SWING AND DOZER
WEIGHT
Note: this figure is calculated with standard bucket.
Model CX35B CX39B
Crawler type Rubber belt
Steel crawler
(OPT)
Rubber belt
Steel crawler
(OPT)
Rotation speed rpm 8.9 8.9
Travel speed km/h
Low
(1st)
High
(2nd)
Low
(1st)
High
(2nd)
Low
(1st)
High
(2nd)
Low
(1st)
High
(2nd)
2.5 4.5 2.5 4.5 2.5 4.5 2.5 4.5
Gradeability % (degree) 58 (30°)
Model (YANMAR) 3TNV88-PYB
Type Vertical. 4-cycle water-cooled diesel engine
Number of cylinders-bore x stroke 3 - ø88 mm x 90 mm
Total displacement L 1.642
Rated output kW / rpm 21.2 / 2400
Maximum torque
Nm / rpm
98.4 / 1440
Starter V x kW 12 x 1.7
Generator V x A 12 x 55
Hydraulic pump Variable displacement axial piston + gear pump
Hydraulic motor Axial piston
Hydraulic Motor w/Reduction gear (Travel) 2-axial pistons, 2-speed motor
Control valve 10-spools multiple control valve
Cylinder (boom, arm, swing, bucket, dozer) Double action cylinder
Return filter Safety valve containing/Filter type (30µ)
Type Boom swing by hydraulic cylinder
Boom swing angle
Right 60°
Left 70°
Stroke of Dozer (above/below) mm 560 / 410 540 / 440
CX35B CX39B
Machine Weight kg
Rubber belt Steel crawler Rubber belt Steel crawler
3000 3110 3580 3700
Upper structure kg 1650 ← 1900 ←
Travel system kg 1050 1160 1140 1260
Equipment (boom + standard arm +
standard bucket)
kg 370 460
Oil and Water kg 80 ←

2. SPECIFICATIONS
2-5
2.4 MACHINE AND COMPONENTS WEIGHT (DRY)
Note: bucket weight is shown with standard bucket weight.
Unit: kg
MODEL
CX35B
RUBBER TRACK STEEL TRACK
CANOPY CAB CANOPY CAB
COMPLETE MACHINE 3360 3500 3470 3610
SUPERSTRUCTURE ASSEMBLY 1650 1790 1650 1790
UPPER FRAME 375 ← ← ←
CANOPY / CAB 85 220 85 220
ENGINE 155 ← ← ←
HYDRAULIC PUMP 28 ← ← ←
RADIATOR 3 ← ← ←
HYDRAULIC TANK 42 ← ← ←
FUEL TANK 4 ← ← ←
SWING BRACKET 93 ← ← ←
SWING CYLINDER 37 ← ← ←
SWING MOTOR 38 ← ← ←
CONTROL VALVE 25 ← ← ←
COUNTERWEIGHT 370 ← ← ←
GUARDS, BONNETS 92 ← ← ←
BOOM CYLINDER 35 ← ← ←
LOWER STRUCTURE ASSEMBLY 1050 ← 1160 ←
LOWER STRUCTURE 310 ← ← ←
FITTINGS 42 ← ← ←
TRAVEL MOTOR 42x2 ← ← ←
LOWER ROLLER 6x8 ← ← ←
IDLE WHEEL 27x2 ← ← ←
IDLER ADJUSTER 14x2 ← ← ←
SPROCKET 9x2 ← ← ←
RUBBER TRACK 125x2 ← — —
STEEL TRACK — — 180x2 ←
ROTARY CONTROL VALVE 22 ← ← ←
DOZER BLADE 140 ← ← ←
DOZER BLADE CYLINDER 27 ← ← ←
ATTACHMENT ASSEMBLY 370 ← ← ←
BOOM ASSEMBLY 170 ← ← ←
BOOM 120 ← ← ←
ARM CYLINDER 30 ← ← ←
ARM ASSEMBLY 120 ← ← ←
ARM 70 ← ← ←
BUCKET CYLINDER 20 ← ← ←
BUCKET LINKS 10 ← ← ←
IDLER LINK 4x2 ← ← ←
BUCKET ASSEMBLY (STANDARD) 81 ← ← ←
FLUIDS ASSEMBLY 80 ← ← ←
HYDRAULIC OIL 42 ← ← ←
FUEL 32 ← ← ←
COOLANT 4 ← ← ←

2. SPECIFICATIONS
2-6
Note: bucket weight is shown with standard bucket weight.
Unit: kg
MODEL
CX39B
RUBBER TRACK STEEL TRACK
CANOPY CAB CANOPY CAB
COMPLETE MACHINE 3760 3900 3870 4010
SUPERSTRUCTURE ASSEMBLY 1900 2040 1900 2040
UPPER FRAME 375 ← ← ←
CANOPY / CAB 85 220 85 220
ENGINE 155 ← ← ←
HYDRAULIC PUMP 28 ← ← ←
RADIATOR 3 ← ← ←
HYDRAULIC TANK 42 ← ← ←
FUEL TANK 4 ← ← ←
SWING BRACKET 93 ← ← ←
SWING CYLINDER 37 ← ← ←
SWING MOTOR 38 ← ← ←
CONTROL VALVE 25 ← ← ←
COUNTERWEIGHT 665 ← ← ←
GUARDS, BONNETS 92 ← ← ←
BOOM CYLINDER 35 ← ← ←
LOWER STRUCTURE ASSEMBLY 1140 ← 1260 ←
LOWER STRUCTURE 370 ← ← ←
FITTINGS 42 ← ← ←
TRAVEL MOTOR 42x2 ← ← ←
LOWER ROLLER 6x8 ← ← ←
IDLE WHEEL 27x2 ← ← ←
IDLER ADJUSTER 14x2 ← ← ←
SPROCKET 9x2 ← ← ←
RUBBER TRACK 134x2 ← — —
STEEL TRACK — — 190x2 ←
ROTARY CONTROL VALVE 22 ← ← ←
DOZER BLADE 150 ← ← ←
DOZER BLADE CYLINDER 27 ← ← ←
ATTACHMENT ASSEMBLY 460 ← ← ←
BOOM ASSEMBLY 190 ← ← ←
BOOM 140 ← ← ←
ARM CYLINDER 34 ← ← ←
ARM ASSEMBLY 140 ← ← ←
ARM 80 ← ← ←
BUCKET CYLINDER 20 ← ← ←
BUCKET LINKS 10 ← ← ←
IDLER LINK 4x2 ← ← ←
BUCKET ASSEMBLY (STANDARD) 89 ← ← ←
FLUIDS ASSEMBLY 80 ← ← ←
HYDRAULIC OIL 42 ← ← ←
FUEL 32 ← ← ←
COOLANT 4 ← ← ←

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

2. SPECIFICATIONS
2-7
2.5 TRANSPORTATION
(1) LOADING MACHINE ON A TRAILER
1) Keep trailer bed clean. Put chocks against truck wheels.
2) Use a ramp or loading deck. Ramps must be strong enough, have a low angle, and correct height. Load and
unload machine on a level surface.
3) Travel machine onto ramps slowly. Centre the machine over the trailer.
4) Lower all attachment.
5) Stop the engine. Remove the key from the starter switch.
WARNING
Do not put chains over or against hydraulic lines or hoses.
6) Fasten machine to trailer with chains or cables.
During transportation, the bucket or attachments may hit the canopy or the cab. Therefore, set the machine in
the transporting position by observing following points:
1. Extend the bucket cylinder fully.
2. Extend the arm cylinder fully.
3. Lower the boom.
4. If machine cannot be transported with dipper cylinder fully extended, remove bucket or attachment and ex-
tend dipper cylinder.
(2) TRANSPORTATION DIMENSION AND WEIGHT OF ATTACHMENT
1) BOOM WITH ARM CYLINDER
2) ARM AND BUCKET
Model CX35B CX39B
L x H x W mm 2390 x 870 x 320 2590 x 810 x 320
Weight with arm cylinder (kg) 163 184
Model CX35B CX39B
L x H x W
mm
2190 x 450 x 500 2360 x 450 x 600
Weight kg 198 219

2. SPECIFICATIONS
2-8
3) EXCAVATOR ARM
4) BUCKET
5) BLADE
w/o cylinder weight
Model CX35B CX39B
L x H x W
mm
1520 x 430 x 280 1690 x 430 x 280
Weight kg 101 123
Model CX35B CX39B
Heaped Capacity m3
0.09 0.11
L x H x W
mm
670 x 620 x 500 670 x 620 x 600
Weight kg 72 78
Model CX35B CX39B
L x H x W
mm
1230 x 346 x 1550 1280 x 345 x 1700
Weight kg 142 150
L
H

2. SPECIFICATIONS
2-9
2.6 CRAWLER TYPE
2.7 TYPE OF BUCKET
Type Model
Crawler
length
mm
Total crawler
width
mm
Number of
Link
Ground pressure
kPa
CANOPY CAB
Rubber belt
CX35B 300 1550 82 29 30
CX39B 300 1700 88 31 32
Steel track (optional)
CX35B 300 1550 42 31 32
CX39B 300 1700 45 32 33
TYPE ARM
Width mm
Heaped
capacity
m3
(ISO 7451)
Weight kg
CX35B
Length
1520 mm
CX39B
Length
1690 mm
Bucket digging 350 0.050 66.77 S z S z
Cleaning buckets 1000 0.160 69.04 „ ‹ „ ‹

2. SPECIFICATIONS
2-10
WARNING
‹ The buckets with this length, during left dipper slewing higher than 1 m from ground, can interfere with the cab.
For a safe use, consult the Dealer and ask for left slewing limiter of the dipper support.
z: Width with lateral cutter
: Width without lateral cutter
S: Generic digging
for digging and sand loading operations, gravel, clay, earth in general, etc.
The specific weight of the material should not be higher than 1400 kg/m3
„: Bucket for digging and carrying sand, gravel, clay, earth in friable and dry state, ditch cleaning, etc.

2. SPECIFICATIONS
2-11
2.8 ENGINE SPECIFICATIONS
2.8.1 SPECIFICATIONS
Model CX35B - CX39B
Engine model 3TNV88-PYB
Type Vertical, 4-cycle water-cooled diesel engine
Number of cylinders-bore x stroke 3 -88 mm x 90 mm
Total displacement 1.642 litre
Compression ratio 19,1
Rated output 21.2 kW at 2400 rpm
Maximum torque 99 ÷ 108 Nm at 1400 rpm
Low idling 1250 ± 25 rpm
High idling 2590 ± 25 rpm
Fuel consumption rate Less than 180 g / PS•h
Allowable tilting angles Continuous; 30° for all direction
Rotation direction Counterclockwise as viewed from flywheel side
Order of ignition 1-3-2-1
Injection time (injection time before top dead centre) 14 ± 1°
Fuel injection pressure
200 kg / cm2 2
Valve action Open Close
Intake valve b.T.D.C. 15 ± 5° a.B.D.C. 45 ± 5°
Exhaust valve b.T.D.C. 56 ± 5° a.B.D.C. 18 ± 5°
Valve clearance Intake valve 0.2 mm in cold condition
Exhaust valve 0.2 mm in cold condition
Thermostat action Start 71 ± 1.5 °C / Fully open 85 °C
Compression pressure 3.43 ± 0.1 MPa at 250 rpm
Lubrication oil pressure 0.44 MPa at 2300 rpm
Dimensions L x H x W 585 x 521 x 648 mm
Dry weight 155 kg
Injection governor Mechanical centrifugal governor (All speed type)
Fuel filter Paper-element cartridge
Lubrication system Forced lubrication with trochoid pump
Cooling system Coolant / radiator
Starter capacity 12 V x 1.7 kW
Generator capacity 12 V x 50 A
Starting aid Air heater (12 V - 400 W)
Cooling water capacity: max / engine 4.0 / 2.0 litres
Engine oil volume: max / effective 6.7 / 2.8 litres
+10
0

CASE CX39B Hydraulic Mini Excavator Service Repair Manual.pdf

More Related Content

Similar to CASE CX39B Hydraulic Mini Excavator Service Repair Manual.pdf (8)

More from f8usejdkdmmd1 (20)

Recently uploaded (20)

CASE CX39B Hydraulic Mini Excavator Service Repair Manual.pdf