Case ih farmall 110 um tractor service repair manual

Printed in U.S.A.
© 2017 CNH Industrial Italia S.p.A. All Rights Reserved.
Case IH is a trademark registered in the United States and many
other countries, owned by or licensed to CNH Industrial N.V.,
its subsidiaries or affiliates.
FARMALL®
110U
FARMALL®
120U
Tractor
Part number 48038069
2nd
edition English
October 2017
Replaces part number 47985320
SERVICE MANUAL

SERVICE MANUAL
Farmall® 110U With 16x16 Semi-Powershift transmission [ZFLD00796 - ]
48038069 02/10/2017
EN

Link Product / Engine
Product Market Product Engine
Farmall® 110U With 16x16
Semi-Powershift transmission
[ZFLD00796 - ]
North America F5GFL413B*B015
Farmall® 120U With 16x16
Semi-Powershift transmission
[ZFLD00125 - ]
North America F5GFL413A*B023
48038069 02/10/2017

Contents
INTRODUCTION
Engine....................................................................................... 10
[10.001] Engine and crankcase ............................................................. 10.1
[10.216] Fuel tanks .......................................................................... 10.2
[10.206] Fuel filters .......................................................................... 10.3
[10.202] Air cleaners and lines .............................................................. 10.4
[10.254] Intake and exhaust manifolds and muffler ......................................... 10.5
[10.500] Selective Catalytic Reduction (SCR) exhaust treatment ........................... 10.6
[10.501] Exhaust Gas Recirculation (EGR) exhaust treatment.............................. 10.7
[10.400] Engine cooling system ............................................................. 10.8
[10.414] Fan and drive ...................................................................... 10.9
[10.310] Aftercooler........................................................................ 10.10
[10.304] Engine lubrication system........................................................ 10.11
[10.218] Fuel injection system............................................................. 10.12
Clutch ....................................................................................... 18
[18.100] Clutch mechanical release control ................................................. 18.1
[18.112] Slip clutch or flywheel damper ..................................................... 18.2
Transmission.............................................................................. 21
[21.111] Semi-Powershift transmission ...................................................... 21.1
[21.133] Semi-Powershift transmission external controls ................................... 21.2
[21.103] Semi-Powershift transmission hydraulic components.............................. 21.3
[21.152] Semi-Powershift transmission internal components ............................... 21.4
[21.160] Creeper ............................................................................ 21.5
[21.109] Transmission cooler and lines...................................................... 21.6
Four-Wheel Drive (4WD) system .................................................. 23
[23.202] Electro-hydraulic control ........................................................... 23.1
48038069 02/10/2017

[23.314] Drive shaft.......................................................................... 23.2
Front axle system ....................................................................... 25
[25.100] Powered front axle ................................................................. 25.1
[25.102] Front bevel gear set and differential ............................................... 25.2
[25.108] Final drive hub, steering knuckles, and shafts ..................................... 25.3
[25.122] Axle suspension control............................................................ 25.4
Rear axle system........................................................................ 27
[27.100] Powered rear axle.................................................................. 27.1
[27.106] Rear bevel gear set and differential................................................ 27.2
[27.120] Planetary and final drives .......................................................... 27.3
Power Take-Off (PTO)................................................................. 31
[31.104] Rear electro-hydraulic control...................................................... 31.1
[31.114] Two-speed rear Power Take-Off (PTO) ............................................ 31.2
[31.116] Three-speed rear Power Take-Off (PTO) .......................................... 31.3
[31.142] Front Power Take-Off (PTO) control ............................................... 31.4
[31.146] Front Power Take-Off (PTO) ....................................................... 31.5
Brakes and controls .................................................................... 33
[33.202] Hydraulic service brakes ........................................................... 33.1
[33.110] Parking brake or parking lock ...................................................... 33.2
Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.204] Remote control valves ............................................................. 35.2
[35.100] Main lift system..................................................................... 35.3
[35.160] Front hitch controls and lines ...................................................... 35.4
[35.162] Front hitch cylinders and lines ..................................................... 35.5
[35.116] Three-point hitch cylinder .......................................................... 35.6
[35.304] Combination pump units ........................................................... 35.7
Hitches, drawbars, and implement couplings.................................. 37
48038069 02/10/2017

[37.100] Drawbars and towing hitches ...................................................... 37.1
[37.110] Rear three-point hitch .............................................................. 37.2
[37.120] Rear three-point hitch linkage...................................................... 37.3
[37.162] Front hitch.......................................................................... 37.4
[37.166] Front hitch linkage.................................................................. 37.5
Frames and ballasting ................................................................. 39
[39.140] Ballasts and supports .............................................................. 39.1
Steering..................................................................................... 41
[41.101] Steering control .................................................................... 41.1
[41.106] Tie rods............................................................................. 41.2
[41.200] Hydraulic control components...................................................... 41.3
[41.216] Cylinders ........................................................................... 41.4
Wheels...................................................................................... 44
[44.511] Front wheels........................................................................ 44.1
[44.520] Rear wheels........................................................................ 44.2
Cab climate control ..................................................................... 50
[50.100] Heating ............................................................................. 50.1
[50.104] Ventilation .......................................................................... 50.2
[50.200] Air conditioning..................................................................... 50.3
Electrical systems....................................................................... 55
[55.100] Harnesses and connectors......................................................... 55.1
[55.525] Cab engine controls................................................................ 55.2
[55.015] Engine control system.............................................................. 55.3
[55.201] Engine starting system ............................................................. 55.4
[55.301] Alternator........................................................................... 55.5
[55.302] Battery.............................................................................. 55.6
[55.011] Fuel tank system ................................................................... 55.7
[55.010] Fuel injection system............................................................... 55.8
48038069 02/10/2017

[55.014] Engine intake and exhaust system................................................. 55.9
[55.988] Selective Catalytic Reduction (SCR) electrical system .......................... 55.10
[55.989] Exhaust Gas Recirculation (EGR) electrical system ............................. 55.11
[55.640] Electronic modules ............................................................... 55.12
[55.513] Cab transmission controls........................................................ 55.13
[55.024] Transmission control system..................................................... 55.14
[55.020] Transmission speed sensors..................................................... 55.15
[55.022] Transmission temperature sensors .............................................. 55.16
[55.045] Front axle control system ........................................................ 55.17
[55.031] Parking brake electrical system .................................................. 55.18
[55.512] Cab controls...................................................................... 55.19
[55.035] Remote control valve electric control ............................................ 55.20
[55.051] Cab Heating, Ventilation, and Air-Conditioning (HVAC) controls................. 55.21
[55.050] Heating, Ventilation, and Air-Conditioning (HVAC) control system............... 55.22
[55.523] Cab hitch controls ................................................................ 55.23
[55.130] Rear three-point hitch electronic control system ................................. 55.24
[55.202] Cold start aid ..................................................................... 55.25
[55.785] Precision farming system ........................................................ 55.26
[55.905] ISOBUS components ............................................................ 55.27
[55.911] Satellite navigation systems...................................................... 55.28
[55.680] Autopilot/Autoguidance .......................................................... 55.29
[55.518] Wiper and washer system........................................................ 55.30
[55.404] External lighting .................................................................. 55.31
[55.405] External lighting switches and relays ............................................ 55.32
[55.408] Warning indicators, alarms, and instruments .................................... 55.33
[55.988] Selective Catalytic Reduction (SCR) electrical system .......................... 55.34
[55.DTC] FAULT CODES.................................................................. 55.35
Front loader and bucket............................................................... 82
48038069 02/10/2017

[82.100] Arm................................................................................. 82.1
Accessories ............................................................................... 88
[88.100] Accessories ........................................................................ 88.1
Platform, cab, bodywork, and decals............................................. 90
[90.118] Protections and footboards......................................................... 90.1
[90.150] Cab................................................................................. 90.2
[90.151] Cab interior......................................................................... 90.3
[90.160] Cab interior trim and panels........................................................ 90.4
[90.154] Cab doors and hatches ............................................................ 90.5
[90.156] Cab windshield and windows ...................................................... 90.6
[90.120] Mechanically-adjusted operator seat............................................... 90.7
[90.124] Pneumatically-adjusted operator seat.............................................. 90.8
[90.100] Engine hood and panels ........................................................... 90.9
[90.102] Engine shields, hood latches, and trims ......................................... 90.10
[90.116] Fenders and guards.............................................................. 90.11
48038069 02/10/2017

INTRODUCTION
48038069 02/10/2017
1

INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your CASE IH Sales and Service Networks.
48038069 02/10/2017
3

INTRODUCTION
Note to the Owner WARNINGS FOR AIR CONDITIONING SYSTEM
REPAIR OPERATIONS
Starting the system at low temperatures can damage the compressor. Only operate the air conditioner when the
engine is hot and the temperature inside the cab is at least 20 °C (68.00 °F).
When disconnecting the hoses, close the ends with plastic caps to prevent foreign matter and humidity from getting
inside the hoses.
Handle the thermostatic sensor carefully to avoid damage that may prevent efficient system operation.
Always use two spanners to unscrew the hose fittings to avoid twisting the fitting.
Do not use any type of engine oil to lubricate the compressor and the system.
Never leave the compressor oil container open, always make sure that it is tightly closed. If left exposed the oil will
absorb humidity from the air and may, subsequently, damage the system.
Do not transfer compressor oil from the original container to another container.
Do not introduce any additives to the compressor oil. Any additional substances could contain elements which are
incompatible with the chemical base of the refrigerant and thus alter its characteristics.
Check that the thermostatic sensor is correctly inserted in the fins on the evaporator to ensure efficient system oper-
ation.
48038069 02/10/2017
4

INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
48038069 02/10/2017
5

SERVICE MANUAL
Engine
48038069 02/10/2017
10

Engine - Engine and crankcase
Engine - Torque
MOIL15TR01705GA 1
Part to tighten Thread Tightening torque
Bolt (5) retaining the front axle
support to the engine block
M20 x 1.5 x 130 587 N·m (432.95 lb ft)
Bolt (4) retaining the engine block to
the front axle
M20 x 1.5 x 110 587 N·m (432.95 lb ft)
Bolt (1) retaining the transmission
housing to the engine block
M12 x 1.25 x 50 121 N·m (89.25 lb ft)
the transmission housing
M12 x 1.25 x 50 121 N·m (89.25 lb ft)
the transmission housing
M12 x 1.25 x 90 121 N·m (89.25 lb ft)
48038069 02/10/2017
10.1 [10.001] / 3

Engine - Remove
WARNING
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
Failure to comply could result in death or serious injury.
W0398A
WARNING
Avoid injury!
Handle all parts carefully. Do not place your hands or fingers between parts. Use Personal Protec-
tive Equipment (PPE) as indicated in this manual, including protective goggles, gloves, and safety
footwear.
W0208A
Prior operation:
Hood - Remove (90.100).
Side panels - Remove (90.100).
Fuel tank - Remove (10.216).
Fender - Remove (90.116).
Cab and platform - Remove (90.150).
1. Position wooden wedges (1) between the front axle and
the front axle support (2) to prevent articulation.
MOIL15TR01239AA 1
2. Drain the engine coolant as described in Radiator -
Drain fluid (10.400).
3. Position a container for transmission oil recovery under
the transmission casing near the plug (1).
4. Remove the plug (1) and drain the transmission oil.
MOIL15TR01232AA 2
48038069 02/10/2017
10.1 [10.001] / 4

5. Loosen the retaining clamp (1) and disconnect the
exhaust pipe (2) as described in Selective Catalytic
Reduction (SCR) muffler and catalyst - Remove
(10.500).
MOIL15TR00525AA 3
6. Disconnect the hydraulic fitting (3) on the capacitor (4)
and loosen (1) the retaining clamp.
7. Disconnect the sensor wiring (2).
MOIL15TR01231AA 4
8. Loosen the retaining nuts and remove the plate (1) re-
taining the air-conditioning system lines (2).
MOIL15TR00766AA 5
9. From the cab side, disconnect the air-conditioning
pipes (2) from the cab to the supercharger, loosening
the retaining nuts (1).
MOIL15TR00764AA 6
48038069 02/10/2017
10.1 [10.001] / 5

10. Release the lines loosening the retaining clamp (1)
screw.
MOIL15TR00326AA 7
11. Remove the air filter (1), see Air cleaner - Remove
(10.202).
MOIL15TR01233AA 8
12. Loosen the fixing clamps (3) and disconnect the pipe
(1) from the turbine to the radiator in the aftercooler.
13. Remove the air conditioning pipe (2) from the capaci-
tor to the cab.
MOIL15TR01234AA 9
14. Disconnect the coupling (2) and loosen the retaining
clamp (1).
15. Remove the air conditioning pipe (4) from the com-
pressor (3).
MOIL15TR01226AA 10
48038069 02/10/2017
10.1 [10.001] / 6

16. Loosen the retaining clamps (2) and remove the pipe
(1) between the aftercooler radiator and the engine.
MOIL15TR01235AA 11
17. Disconnect the electrical connections (1) of the inlet
temperature sensor of the Diesel Oxidation Catalyst
DOC and the electrical connections of the NOx elec-
tronic control unit (2).
MOIL15TR00710AA 12
18. Loosen the clamp (5) retaining the diesel exhaust fluid
dosing module DEF/ADBLUE® (6).
19. Leaving the lines and electrical connection connected,
remove the diesel exhaust fluid dosing module DEF/
ADBLUE® (6) from the diesel oxidation catalyst (DOC)
(1) and move it on one side.
20. Disconnect the electrical connection (2) of the coolant
control valve (3) and the hydraulic lines (4).
MOIL15TR01236AA 13
21. Disconnect the inlet pipe (5) of the filter loosening the
retaining clamps.
22. Disconnect the hydraulic fitting (3) of the heat ex-
changer pipe.
23. Loosen and remove the retaining clamp (4).
24. Loosen the rear retaining bolts (2) of the front trans-
mission drive shaft guard (1).
MOIL15TR01238AA 14
48038069 02/10/2017
10.1 [10.001] / 7

25. Disconnect the oil delivery line (2) to the control
valves.
26. Release the steering cylinder control lines from the re-
taining clamps (4) and disconnect the hydraulic fittings
(5) to remove them.
27. Loosen the front retaining bolts (1) from the front trans-
mission drive shaft guard.
28. Disconnect the hydraulic fitting (3) of the oil pipe.
MOIL15TR01237AA 15
29. Remove the front transmission drive shaft (1) as de-
scribed in Front drive shaft - Remove (23.314).
MOIL15TR01371AA 16
30. Remove the retaining clamp (5) to release the lines.
31. Remove the sleeve (1) from the oil pump to the oil
filter.
32. Disconnect the hydraulic connections (3) and (6).
33. Loosen the retaining bolts (2) and remove the oil filter
unit (4).
MOIL15TR01227AA 17
34. On the right-hand side of the engine disconnect the
hydraulic connections (4) and (2) of the lines to the
hydraulic steering system control valve.
35. Loosen the retaining bolts (1) of the filter support and
remove the hydraulic steering system oil filter unit (3).
36. Remove the hydraulic steering system filter unit.
MOIL15TR01221AA 18
48038069 02/10/2017
10.1 [10.001] / 8

37. Remove the protective grille (1).
MOIL15TR00544AA 19
38. Disconnect the cab heating pipes (1).
39. Loosen the retaining clamp (2) and disconnect the line
(3) from the conveyor.
MOIL15TR01222AA 20
40. Loosen the retaining clamp (2) and disconnect the
pipe (1) from the conveyor (3).
MOIL15TR01223AA 21
41. Remove the starter motor (1) on the right-hand side of
the engine.
MOIL15TR01224AA 22
48038069 02/10/2017
10.1 [10.001] / 9

42. Remove the hood support (2), as described in Hood
pivoting system - Remove (90.100).
43. Remove the Diesel Oxidation Catalyst (DOC) (1) as
described in Diesel Oxidation Catalyst (DOC) - Re-
move (10.500).
MOIL15TR01225AA 23
44. Disconnect the wiring harness starting from the en-
gine control unit (1) up to the maxi fuse box taking care
to disconnect the temperature and pressure sensors
placed on the engine.
45. Collect the wiring on both sides of the engine and re-
move it.
MOIL15TR01228AA 24
46. Hook the rear part of the engine onto a hoist using
chains or hoisting ropes (apply two eyebolts, one to
the right and one to the left, on the upper part of the
flange containing the flywheel). Position a fixed jack
stand (2) under the clutch housing (1) near the flange
coupling on the engine.
WLAPL4S10C129A 25
47. Position the movable tool for dismantling tractors
380003114 (2) with the support bracket and adapter
plate under the engine. Place a wooden block (1) in
the contact points between the tool and the engine.
WLAPL4S10C140A 26
48038069 02/10/2017
10.1 [10.001] / 10

48. Remove the retaining screws (1) between the engine
casing (2) and the transmission casing (3).
MOIL15TR01229AA 27
49. Separate the engine (1) from the transmission using
the specific tool 380003114 (2) .
WLAPL4S10C131AA 28
50. Insert the fixed jack stand (1) under the ballast support
and secure the front wheels with wooden wedges (2).
WLAPL4S10C132AA 29
51. Position a fixed jack stand (3) under the splined sup-
port (1) of the front axle Power Take-Off (PTO), placing
a wooden plug (2) between parts (3) and (1).
WLAPL4S10C133A 30
48038069 02/10/2017
10.1 [10.001] / 11

52. Position a jack stand under the rear part of the engine
so as to be able to release the hoist with the coupling
device in complete safety. Add a rope or chain (1) also
on the front of the engine. Take up the slack with the
lifting device, keeping the engine balanced.
WLAPL4S10C136A 31
53. Remove the screws (1) and (3) that retain the front
suspension (2) to the engine block (4). Collect the
related washers.
MOIL15TR01702AA 32
54. Check that there are no parts still connected or that
interfere with the aftercooler group and the engine.
55. Slowly remove the engine (2) from the front suspen-
sion (3) avoiding incorrect movements to prevent
damaging the fan (1) and the radiator body.
WLAPL4S10C138A 33
48038069 02/10/2017
10.1 [10.001] / 12

Engine - Install
WARNING
Heavy objects!
Lift and handle all heavy components using lifting equipment with adequate capacity. Always support
units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
W0398A
WARNING
Avoid injury!
Handle all parts carefully. Do not place your hands or fingers between parts. Use Personal Protec-
tive Equipment (PPE) as indicated in this manual, including protective goggles, gloves, and safety
footwear.
W0208A
Prior operation:
Engine - Remove (10.001).
1. Slowly position the engine (2) on the front suspension
(3) avoiding incorrect movements to prevent damaging
the fan (1) and the radiator body.
WLAPL4S10C138A 1
2. Secure the front suspension (4) to the engine block
(2) tightening the screws (1) and (3) as described in
Engine - Torque (10.001).
MOIL15TR01702AA 2
48038069 02/10/2017
10.1 [10.001] / 13

3. Using the special tool 380003114 (2) move the whole
engine lock front suspension (1) towards the transmis-
sion casing.
WLAPL4S10C131AA 3
4. Secure the engine (2) to the transmission casing (3)
tightening the screws (1) as described in Engine -
Torque (10.001).
MOIL15TR01229AA 4
5. Remove the special tool (2) 380003114 recovering the
adapter plate (1).
WLAPL4S10C140A 5
6. Starting from the engine control unit (1), lay out the
electric wiring harness restoring the connections of the
temperature and pressure sensors placed on the en-
gine.
MOIL15TR01228AA 6
48038069 02/10/2017
10.1 [10.001] / 14

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

7. Position and secure the catalyst (1) as described in
Diesel Oxidation Catalyst (DOC) - Install (10.500).
8. Position the hood support (2), as described in Hood
pivoting system - Install (90.100).
MOIL15TR01225AA 7
9. Position and secure the starter motor (1) on the right-
hand side of the engine.
MOIL15TR01224AA 8
10. Connect the pipe (1) to the conveyor (3) and tighten
the clamp (2) to secure it.
MOIL15TR01223AA 9
11. Connect the cab heating pipes (1).
12. Connect the pipe (3) to the conveyor and tighten the
clamp (2) to secure it.
MOIL15TR01222AA 10
48038069 02/10/2017
10.1 [10.001] / 15

13. Position and secure the protective grill (1).
MOIL15TR00544AA 11
14. On the right-hand side of the engine position the hy-
draulic steering system oil filter unit (3) and tighten the
retaining bolts (1) of the support.
15. Connect the hydraulic connections (2) and (4) of the
lines to the hydraulic steering system control valve.
MOIL15TR01221AA 12
16. Position the oil filter unit (4) and tighten the retaining
screws (2).
17. Connect the hydraulic connections (6) and (3).
18. Tighten the retaining clamp (5) to secure the lines.
19. Connect the sleeve (1) from the oil pump to the oil
filter.
MOIL15TR01227AA 13
20. Fit the transmission drive shaft as described in Front
drive shaft - Install (23.314).
MOIL15TR01371AA 14
48038069 02/10/2017
10.1 [10.001] / 16

21. Connect the hydraulic fitting (3) in the oil pipe.
22. Screw the front retaining screws (1) of the front trans-
mission drive shaft guard.
23. Screw the retaining clamps (4) to secure the steering
cylinder control lines. Connect the hydraulic connec-
tions (5).
24. Connect the hydraulic oil delivery fitting (2) to the con-
trol valves.
MOIL15TR01237AA 15
25. Screw the rear retaining bolts (2) of the front transmis-
sion drive shaft guard (1).
26. Connect the hydraulic fitting (3) of the heat exchanger
pipe and secure it screwing the clamp (4).
27. Connect the filter intake pipe (5).
MOIL15TR01238AA 16
28. Insert the diesel exhaust liquid dosing module DEF/
ADBLUE® (6) in the Diesel Oxidation Catalyst (DOC)
(1) and secure it tightening the clamp (5).
29. Connect the hydraulic fittings (3) from the coolant con-
trol valve (4).
30. Connect the electric wiring harness (2).
MOIL15TR01236AA 17
31. Connect the electrical connections (1) of the inlet tem-
perature sensor to the DOC and the electrical connec-
tions of the NOx control module (2).
MOIL15TR00710AA 18
48038069 02/10/2017
10.1 [10.001] / 17

32. Position the pipe (1) from the after cooler radiator to
the engine and secure it tightening the clamps (2).
MOIL15TR01235AA 19
33. Position the air conditioning pipe (4) from the super-
charger (3).
34. Connect the hydraulic coupling (2).
35. Tighten the retaining clamp (1) to secure the pipe.
MOIL15TR01226AA 20
36. Position the air conditioned pipe (2) from the capacitor
to the cab.
37. Connect the pipe (1) from the turbine to the aftercooler
radiator and secure it screwing the clamps (3).
MOIL15TR01234AA 21
38. Install the air cleaner (1) , as described in Air cleaner
- Install (10.202) .
MOIL15TR01233AA 22
48038069 02/10/2017
10.1 [10.001] / 18

39. From the cab side, connect the air-conditioning hoses
(2) from the cab to the supercharger, tightening the
retaining nuts (1).
MOIL15TR00764AA 23
40. Fit the plate (1) securing the air-conditioning hoses (2)
and tighten the retaining nuts.
MOIL15TR00766AA 24
41. Secure the lines screwing the retaining clamp screw
(1).
MOIL15TR00326AA 25
42. Connect the hydraulic fitting (3) on the capacitor (4)
and tighten the (1) retaining clamp screw.
43. Connect the sensor wiring (2).
MOIL15TR01231AA 26
48038069 02/10/2017
10.1 [10.001] / 19

Case ih farmall 110 um tractor service repair manual

More Related Content

Similar to Case ih farmall 110 um tractor service repair manual (16)

More from jfjskeksemm (20)

Recently uploaded (20)

Case ih farmall 110 um tractor service repair manual