Case ih farmall 75 c tractor service repair manual

Printed in U.S.A.
Copyright © 2011 CNH America LLC. All Rights Reserved.
Case IH is a registered trademark of CNH America LLC.
Racine Wisconsin 53404 U.S.A.
Part number 84419878A
English
October 2011
SERVICE MANUAL
FARMALL®
55C
FARMALL®
65C
FARMALL®
75C
Tractor

INTRODUCTORY NOTES
-- This manual is divided into sections identified by two--figure numbers and each section has independent
page numbering.
-- The different sections can easily be found by consulting the table of contents on the following pages.
-- The document number of the manual and the edition/update dates are given at the bottom of each page.
-- The pages of future updates will be identified by the same print number followed by an additional digit:
standard manual first edition 84419878A -- 1st update 84419878A1 -- 2nd update 84419878A2 -- etc.
The pages of the update can replace or supplement the pages of the standard manual; the necessary
information for the procedure to add or replace the pages is given on the title page of the update.
The publication will be completed with an appropriate index.
If it is necessary to issue a new updated manual (2nd edition) it will have document number 84419878B, this
indicates that the manual is composed of the standard version 84419878A completed with all the updates:
1st update 84419878A1 -- 2nd update 84419878A2 -- etc.
-- The information contained in this manual was current on the date printed on each section. As CASE IH
constantly improves its product range, some information may be out of date subsequent to modifications
implemented for technical or commercial reasons, or to meet legal requirements in different countries.
In the event of conflicting information, consult the CASE IH Sales and Service Departments.
IMPORTANT WARNINGS
-- All maintenance and repair work described in this manual must be performed exclusively by CASE IH service
technicians, in strict accordance with the instructions given and using any specific tools necessary.
-- Anyone performing the operations described herein without strictly following the instructions is personally
responsible for any eventual injury or damage to property.
-- The Manufacturer and all organisations belonging to the Manufacturer’s distribution network, including but
not restricted to national, regional or local distributors, will accept no responsibility for personal injury or
damage to property caused by abnormal function of parts and/or components not approved by the
Manufacturer, including those used for maintenance and/or repair of the product manufactured or marketed
by the Manufacturer.
In any case, the product manufactured or marketed by the Manufacturer is covered by no guarantee of any
kind against personal injury or damage to property caused by abnormal function of parts and/or components
not approved by the Manufacturer.
No part of the text or illustrations may be copied
PRINTED IN FRANCE
 CNH GLOBAL N.V.
Print no. 84419878A -- 06 -- 2011

CONTENTS 3
84419878A -- 06 -- 2011
CONTENTS
Page Date
00 -- GENERAL GUIDELINES
General instructions . . . . . 1--2 06--11
Safety regulations . . . . . . . 3--4--5 06--11
Tractor refuelling . . . . . . . . 6 06--11
10 -- ENGINE
CHAPTER 1
Summary . . . . . . . . . . . . . . . 1 06--11
General specifications 2--3 06--11
Engine removal--installa-
tion . . . . . . . . . . . . . . . . . . . . 4--5--6--7--8
--9--10
06--11
Removal--Installation fuel
tank . . . . . . . . . . . . . . . . . . . 11--12 06--11
Coolant radiator removal--
installation . . . . . . . . . . . . . . 13--14--15 06--11
Accelerator control cable
adjustment . . . . . . . . . . . . . 16 06--11
18 -- CLUTCH
Main Data . . . . . . . . . . . . . . 1 06--11
Torque Specifications . . . . 2 06--11
Tools . . . . . . . . . . . . . . . . . . 2 06--11
Sections . . . . . . . . . . . . . . . 3 06--11
Troubleshooting . . . . . . . . . 4 06--11
Removal--Installation --
clutch . . . . . . . . . . . . . . . . . . 5 06--11
Clutch Overhaul . . . . . . . . . 6--7--8--9 06--11
Checks and measure-
ments -- clutch . . . . . . . . . . 10--11 06--11
Adjustments -- clutch disen-
gagement levers . . . . . . . . 11 06--11
Adjustments -- clutch pedal
. . . . . . . . . . . . . . . . . . . . . . . . 12 06--11
Sectional view of PTO
clutch servo control . . . . . . 13 06--11
Description and operation
of PTO servo control . . . . . 14--15 06--11
PTO servo control adjust-
ment . . . . . . . . . . . . . . . . . . . 16 06--11
PTO engaged switch ad-
justment . . . . . . . . . . . . . . . . 17 06--11
Page Date
21 -- GEAR TRANSMISSION
Chapter 1 -- Mechanical transmission
Main Data . . . . . . . . . . . . . . 1--2 06--11
Torque Specifications . . . . 2--3 06--11
Tools . . . . . . . . . . . . . . . . . . 4 06--11
Sections . . . . . . . . . . . . . . . 5--6--7 06--11
Description and operation 8 06--11
Troubleshooting . . . . . . . . . 8--9 06--11
rear transmission -- gear-
box casing . . . . . . . . . . . . . . 10--11--12--
13 06--11
Disassembly--Assembly --
transmission--gearbox ca-
sing . . . . . . . . . . . . . . . . . . . 17--18 06--11
clutch casing . . . . . . . . . . . . 19--20--21 06--11
Sealing compound applica-
tion diagram . . . . . . . . . . . . 22 06--11
Transmission oil cooler re-
moval--installation . . . . . . . 23 06--11
CHAPTER 3 -- Power Shuttle transmission
Main Data . . . . . . . . . . . . . . 1--2 06--11
Tools . . . . . . . . . . . . . . . . . . 4 06--11
Sections . . . . . . . . . . . . . . . 5--6--7 06--11
Description and operation . 8 06--11
clutch casing . . . . . . . . . . . . 9--10--11 06--11
Main clutch adjustments . . 12 06--11
23 -- DRIVE LINES
Main Data . . . . . . . . . . . . . . 1 06--11
Sections . . . . . . . . . . . . . . . 3--4 06--11
Drive shafts and guard. Di-
sassembly -- Assembly . . . 7 06--11

4 CONTENTS
84419878A -- 06 -- 2011
Page Date
Removal--Installation -- dri-
ve gear casing . . . . . . . . . . 8 06--11
25 -- FRONT AXLE MECHANICAL
TRANSMISSION
CHAPTER 1 -- Front mechanical transmission
Main Data . . . . . . . . . . . . . . 1--2 06--11
Tools . . . . . . . . . . . . . . . . . . 5 06--11
Sections . . . . . . . . . . . . . . . 6 06--11
front axle . . . . . . . . . . . . . . . 8--9--10 06--11
Front axle. Disassembly --
Assembly . . . . . . . . . . . . . . 11--12--13--
14--15--16--
17--18 06--11
Replacing steering knuckle
pins and bearings . . . . . . . 19 06--11
Adjustments -- steering
knuckle bearings . . . . . . . . 20--21 06--11
Adjustments -- bevel drive 22--23--24--
25--26--27--
28 06--11
Overhaul -- front differential 29 06--11
LIM--SLIP self--locking dif-
ferential . . . . . . . . . . . . . . . . 30--31 06--11
Checking leading wheel
alignment . . . . . . . . . . . . . . 32 06--11
front epicyclic final drive . . 33--34 06--11
27 -- REAR MECHANICAL
TRANSMISSION
Main Data . . . . . . . . . . . . . . 1--2 06--11
Tools . . . . . . . . . . . . . . . . . . 5 06--11
Sections . . . . . . . . . . . . . . . 6--7 06--11
transmission--gearbox ca-
sing . . . . . . . . . . . . . . . . . . . 9--10--11--
12 06--11
Adjustments -- differential
lock engagement sleeve
position . . . . . . . . . . . . . . . . 13 06--11
Page Date
Adjustments -- bevel drive 14--15--16 06--11
Removal -- Installation
side gear casing . . . . . . . . . 17--18--19--
20 06--11
drive wheel shaft . . . . . . . . 21--22 06--11
31 -- POWER TAKE--OFF
CHAPTER 1 -- Mechanical power take--off
Main Data . . . . . . . . . . . . . . 1--2 06--11
Sections . . . . . . . . . . . . . . . 5--6 06--11
Description and operation . 7--8 06--11
33 -- BRAKES
Main Data . . . . . . . . . . . . . . 1--2 06--11
Sections . . . . . . . . . . . . . . . 3 06--11
Removal--Installation -- ser-
vice brake . . . . . . . . . . . . . . 7 06--11
Removal--Installation -- ser-
vice brake pump . . . . . . . . . 8--9 06--11
Adjustments -- service bra-
ke pedals travel . . . . . . . . . 10 06--11
Service brake circuit air
bleeding . . . . . . . . . . . . . . . . 11--12 06--11
35 -- HYDRAULIC SYSTEMS
CHAPTER 1 -- Rear mechanical hydraulic lift
Main Data . . . . . . . . . . . . . . 2 06--11
Tools . . . . . . . . . . . . . . . . . . 3 06--11
Sections . . . . . . . . . . . . . . . 4 06--11
Description and operation . 6--7--8--9--
10--11 06--11
Lift internal controls. Disas-
sembly -- Assembly . . . . . . 12--13--14--
15 06--11

CONTENTS 5
84419878A -- 06 -- 2011
Page Date
Draft reading unit Disas-
sembly -- Assembly . . . . . . 16--17 06--11
Lift arms shaft. Disassem-
bly -- Assembly . . . . . . . . . . 18--19 06--11
Removal--Installation -- lift
control valve . . . . . . . . . . . . 20 06--11
Adjusting the lift . . . . . . . . . 21--22--23 06--11
CHAPTER 2 -- Open centre system auxiliary
control valves
Main Data . . . . . . . . . . . . . . 2 06--11
Tools . . . . . . . . . . . . . . . . . . 2 06--11
Sections . . . . . . . . . . . . . . . 3--4 06--11
Description and operation . 5--6--7--8 06--11
Auxiliary control valves. Di-
sassembly -- Assembly . . . 9--10--11 06--11
CHAPTER 3 -- Trailer brakes auxiliary control
valves
Sections . . . . . . . . . . . . . . . 1 06--11
Description and operation . 1--2--3--4--5
--6--7 06--11
Troubleshooting . . . . . . . . . 8--9--10 06--11
CHAPTER 8 -- Front Loader
Main Data . . . . . . . . . . . . . . 1 06--11
Sections . . . . . . . . . . . . . . . 2 06--11
Parking the front loader . . . 6 06--11
Front loader arm connec-
tion bracket Removal--In-
stallation . . . . . . . . . . . . . . . 7 06--11
Replacement of control
struts (mod. MSL) . . . . . . . 8 06--11
Replacement of triangular
articulation levers (mod.
MSL) . . . . . . . . . . . . . . . . . . 9 06--11
Bucket support device re-
Position indicator disas-
sembly--assembly . . . . . . . 11 06--11
Bushing replacement . . . . 12--13 06--11
Loader cylinder removal--
installation . . . . . . . . . . . . . . 14 06--11
Page Date
Bucket control cylinder re-
Replacement of pins . . . . . 16 06--11
41 -- STEERING
CHAPTER 1 -- Steering
Main Data . . . . . . . . . . . . . . 2 06--11
Tools . . . . . . . . . . . . . . . . . . 3 06--11
Description and operation . 4--5--6 06--11
View of hydrostatic steering
control valve components . 7 06--11
Replacement -- hydrostatic
steering wheel . . . . . . . . . . 10 06--11
Removal--Installation -- hy-
drostatic steering control
valve . . . . . . . . . . . . . . . . . .
11--12 06--11
hydrostatic control valve . . 13--14--15--
16--17--18--
19--20--21--
22--23--24--
25--26--27--
28 06--11
Hydrostatic steering control
valve bench testing . . . . . . 29--30 06--11
Pressure relief valve testing 31 06--11
Steering control cylinder.
Removal -- Installation . . . . 32--33 06--11
Steering control cylinder.
Disassembly--Assembly . . 34--35 06--11
50 -- CAB HVAC SYSTEM
Safety regulations . . . . . . . 2 06--11
Main Data . . . . . . . . . . . . . . 3 06--11
Tools . . . . . . . . . . . . . . . . . . 4 06--11
Operating principles . . . . . 5 06--11
Conditioning system com-
ponents . . . . . . . . . . . . . . . . 6--7--8--9--
10 06--11
Cab controls . . . . . . . . . . . . 11--12--13 06--11
Testing operation and coo-
ling . . . . . . . . . . . . . . . . . . . . 14--15 06--11

6 CONTENTS
84419878A -- 06 -- 2011
Page Date
Air conditioning system
maintenance . . . . . . . . . . . . 16--17 06--11
Troubleshooting . . . . . . . . . 18--19--20--
21 06--11
Refrigerant recovery--recy-
cling and evacuation--char-
ging stations . . . . . . . . . . . . 22--23 06--11
Dehydration, recharging
and refrigeration check . . . 24--25--26--
27--28--29--
30 06--11
Checking for and elimina-
ting any gas leaks . . . . . . . 31--32 06--11
Cab heating/air--conditio-
ning system. Removal -- In-
stallation . . . . . . . . . . . . . . . 33--34 06--11
Cab electric fan unit. Disas-
sembly -- Assembly . . . . . . 35 06--11
Air--conditioning system
condenser removal--instal-
lation . . . . . . . . . . . . . . . . . . 36 06--11
55 -- ELECTRICAL SYSTEM
CHAPTER 1 -- Instruments
Summary . . . . . . . . . . . . . . . 1 06--11
Digital analog instrument 2 06--11
Speedometer/tachometer . 3 06--11
LCD panel settings . . . . . . 3÷7 06--11
Coolant temperature . . . . . 7 06--11
Fuel level . . . . . . . . . . . . . . . 7 06--11
Indicator lights . . . . . . . . . . 8÷9 06--11
Transmitters, sensors and
switches . . . . . . . . . . . . . . . 10÷20 06--11
Electronic control unit in-
puts/outputs (ADIC) . . . . . . 21÷23 06--11
CHAPTER 2 -- Starting System
Summary . . . . . . . . . . . . . . . 1 06--11
Technical data . . . . . . . . . . 2 06--11
Starter and recharging cir-
cuit . . . . . . . . . . . . . . . . . . . . 4--5 06--11
Fuse and relay locations . . 7--8 06--11
Page Date
System testing . . . . . . . . . . 8÷10 06--11
Starter motor removal--in-
stallation . . . . . . . . . . . . . . . 11÷13 06--11
CHAPTER 3 -- Charging system
Summary . . . . . . . . . . . . . . . 1 06--11
Technical data . . . . . . . . . . 2 06--11
Tools . . . . . . . . . . . . . . . . . . . 3 06--11
Description and operation . 3--4 06--11
System testing . . . . . . . . . . 5 06--11
Belt Tension . . . . . . . . . . . . . 6 06--11
Alternator motor removal
and installation . . . . . . . . . . 7--8 06--11
CHAPTER 4 -- Battery
Summary . . . . . . . . . . . . . . . 1 06--11
Technical data . . . . . . . . . . 2 06--11
Battery removal and instal-
lation . . . . . . . . . . . . . . . . . . 3 06--11
Battery testing and char-
ging procedure . . . . . . . . . . 4÷14 06--11
CHAPTER 5 -- Electrical circuits
Summary . . . . . . . . . . . . . . . 1 06--11
Maxi power fuses . . . . . . . . 2÷5 06--11
Power fuses . . . . . . . . . . . . 5÷34 06--11
Battery cut--out . . . . . . . . . . 34 06--11
Sockets . . . . . . . . . . . . . . . . 35--36 06--11
Grid heater . . . . . . . . . . . . . 37 06--11
Electronic modules . . . . . . 37--38 06--11
Main Connectors . . . . . . . . 38--39 06--11
Ground points identification 40÷42 06--11
How to use the wiring dia-
grams . . . . . . . . . . . . . . . . . . 43÷47 06--11
Components in descriptive
order . . . . . . . . . . . . . . . . . . 48÷52 06--11
List of tables for system wi-
thout “standard and full op-
tional” cab . . . . . . . . . . . . . . 53--54 06--11
Components with code in
ascending order . . . . . . . . . 55÷57 06--11

CONTENTS 7
84419878A -- 06 -- 2011
Page Date
Tables . . . . . . . . . . . . . . . . . 58÷96 06--11
List of tables for system
with “standard and full op-
tional” cab . . . . . . . . . . . . . . 97--98 06--11
ascending order . . . . . . . . . 99÷103 06--11
Tables . . . . . . . . . . . . . . . . . 104÷160 06--11
CHAPTER 6 -- Wiring Harnesses and
Connectors
Summary . . . . . . . . . . . . . . . 1 06--11
Components in descriptive
order . . . . . . . . . . . . . . . . . . 2÷7 06--11
ascending order . . . . . . . . . 8÷12 06--11
Harnesses . . . . . . . . . . . . . . 13÷20 06--11
Connectors . . . . . . . . . . . . . 21÷92 06--11
Page Date
90 -- PLATFORM, CAB, BODYWORK
CHAPTER 1 -- Cab
Bonnet. Removal -- Installa-
tion . . . . . . . . . . . . . . . . . . . . 2 06--11
Cab assembly with plat-
form. Removal -- Installa-
tion . . . . . . . . . . . . . . . . . . . . 3--4--5--6--
7--8--9 06--11
Cab right--hand pillar guard
removal -- installation . . . . . 10 06--11
Cab right--hand top guard
removal -- installation . . . . . 11 06--11
Cab right--hand mudguard
guard removal--installation 12 06--11
Cab left--hand top guard re-
Windows. Replace . . . . . . . 14--15--16 06--11

SECTION 00 -- GENERAL -- CHAPTER 1 1
84419878A -- 06 -- 2011
GENERAL INSTRUCTIONS
IMPORTANT NOTICE
All maintenance and repair work described in this manual must be performed exclusively by CASE IH service
technicians, in strict accordance with the instructions given and using any specific tools necessary.
Anyone performing the operations described herein without strictly following the instructions is personally
responsible for any eventual injury or damage to property.
BATTERY
Before carrying out any kind of service operation disconnect and isolate the battery negative lead, unless
otherwise requested for specific operations (e.g.: operations requiring the engine to be running), after which it
is necessary to disconnect the above--mentioned lead to complete the work.
SHIMMING
For each adjustment operation, select adjusting shims and measure individually using a micrometer, then add
up the recorded values. Do not rely on measuring the entire shimming set, which may be incorrect, or the rated
value indicated for each shim.
ROTATING SHAFT SEALS
For correct rotating shaft seal installation, proceed as follows:
-- before assembly, allow the seal to soak in the oil it will be sealing for at least thirty minutes;
-- thoroughly clean the shaft and check that the working surface on the shaft is not damaged;
-- position the sealing lip facing the fluid; with hydrodynamic lips, take into consideration the shaft rotation
direction and position the grooves so that they will deviate the fluid towards the inner side of the seal;
-- smear the sealing lip with a thin layer of lubricant (use oil rather than grease) and fill the gap between the
sealing lip and the dust lip on double lip seals with grease;
-- insert the seal in its seat and press down using a flat punch, do not tap the seal with a hammer or mallet;
-- whilst inserting the seal, check that the it is perpendicular to the seat; once settled, make sure that it makes
contact with the thrust element, if required;
-- to prevent damaging the seal lip on the shaft, position a protective guard during installation operations.
O--RING SEALS
Lubricate the O--RING seals before inserting them in the seats, this will prevent them from overturning and
twisting, which would jeopardise sealing efficiency.
SEALING COMPOUNDS
Apply one of the following sealing compounds on the mating surfaces marked with an X: LOCTITE 518 or
LOCTITE 5205 or SUPERBOND 559 or BETALOK A272M.
Before applying the sealing compound, prepare the surfaces as follows:
-- remove any incrustations using a wire brush;
-- thoroughly degrease the surfaces using one of the following cleaning agent: trichlorethylene, petrolor awater
and soda solution.
BEARINGS
When installing bearings it is advised to:
-- heat the bearings to 80 ÷ 90 0C before fitting on the shafts;
-- allow the bearings to cool before installing them from the outside.

2 SECTION 00 -- GENERAL -- CHAPTER 1
84419878A -- 06 -- 2011
SPRING PINS
When fitting split socket elastic pins, ensure that the pin notch is positioned in the direction of the force required
to stress the pin.
Spiral spring pins do not require special positioning
SPARE PARTS
Use genuine parts only.
Only genuine spare parts guarantee the same quality, duration and safety as they are the same parts that are
assembled during production.
Only genuine parts can offer this guarantee.
When ordering spare parts, always provide the following information:
-- tractor model (commercial name) and frame number;
-- engine type and number;
-- part number of the ordered part, which can be found on the “Spare Parts Catalogue”, which is the base for
order processing.
NOTES FOR EQUIPMENT
The tools that CASE IH offer and illustrate in this manual are:
-- specifically researched and designed for use with CASE IH vehicles;
-- necessary to make a reliable repair;
-- accurately built and strictly tested to offer efficient and long--lasting working means.
By using these tools, repair personnel will benefit from:
-- operating in optimal technical conditions;
-- obtaining the best results;
-- save time and effort;
-- working in safe conditions.
IMPORTANT NOTES
Wear limit values indicated for certain parts are recommended, but not binding. The terms “front”, “rear”,
“right--hand” and “left--hand” (when referred to different parts) are intended as seen from the driving position with
the tractor in the normal direction of movement.
MOVING THE TRACTOR WITH THE BATTERY REMOVED
External power supply cables should only be connected to the respective positive and negative cable terminals,
using efficient clamps that guarantee adequate and secure contact.
Disconnect all services (lights, windshield wipers, etc.) before starting the vehicle.
If the tractor electrical system requires checking, carry out operations with the power supply connected. Once
checking is completed, disconnect all services and switch off the power supply before disconnecting the cables.

84419878A -- 06 -- 2011
SAFETY RULES
PAY ATTENTION TO THIS SYMBOL
This warning symbol points out important messages
concerning your safety.
Carefully read the following safety regulations and
observe advised precautions in order to avoid
potential hazards and safeguard your health and
safety.
In this manual the symbol is accompanied by the
following key--words:
WARNING -- Warnings concerning unsuitable repair
operations that may jeopardise the safety of Repair
personnel.
DANGER -- Specific warnings concerning potential
hazards for operator safety or for other persons
directly or indirectly involved.
TO PREVENT ACCIDENTS
Most accidents or injuries that occur in workshops
are the result of non--observance of simple and
fundamental safety regulations. For this reason, IN
MOST CASES THESE ACCIDENTS CAN BE
AVOIDED by foreseeing possible causes and
consequently acting with the necessary caution and
care.
Accidents may occur with all types of vehicle,
regardless of how well it was designed and built.
A careful and judicious service technician is the best
guarantee against accidents.
Precise observance of the most basic safety rule is
normally sufficient to avoid many serious accidents.
DANGER. Never carry out any cleaning, lubrication
or maintenance operations when the engine is
running.
SAFETY RULES
GENERAL GUIDELINES
-- Carefully follow specified repair and
maintenance procedures.
-- Do not wear rings, wristwatches, jewels,
unbuttoned or flapping clothing such as ties, torn
clothes, scarves, open jackets or shirts with open
zips which could get caught on moving parts.
Use approved safety clothing such as
anti--slipping footwear, gloves, safety goggles,
helmets, etc.
1
-- Do not carry out repair operations with someone
sitting in the driver’s seat, unless the person is a
trained technician who is assisting with the
operation in question.
-- Do not operate the vehicle or use any of the
implements from different positions, other than
the driver’s seat.
-- Do not carry out operations on the vehicle with
the engine running, unless specifically indicated.
-- Stop the engine and ensure that all pressure is
relieved from hydraulic circuits before removing
caps, covers, valves, etc.
-- All repair and maintenance operations must be
carried out using extreme care and attention.
-- Service steps and platforms used in a workshop
or in the field should be built in compliance with
the safety rules in force.
-- Disconnect the batteries and label all controls to
indicate that the vehicle is being serviced. Block
the machine and all equipment which should be
raised.
-- Do not check or fill fuel tanks, accumulator
batteries, nor use starting liquid when smoking or
near naked flames, as these fluids are
inflammable.
-- Brakes are inoperative when manually released
for repair or maintenance purposes. Use blocks
or similar devices to control the machine in these
conditions.
-- The fuel nozzle should always be in contact with
the filling aperture: Maintain this contact until the
fuel stops flowing into the tank to avoid possible
sparks due to static electricity buildup.

4 SECTION 00 -- GENERAL -- CHAPTER 1
84419878A -- 06 -- 2011
-- Only use specified towing points for towing the
vehicle. Connect parts carefully. Make sure that
all pins and/or locks are secured in position
before applying traction. Never remain near the
towing bars, cables or chains that are operating
under load.
-- Transport vehicles that cannot be driven using a
trailer or a low--loading platform trolley, if
available.
-- When loading or unloading the vehicle from the
trailer (or other means of transport), select a flat
area capable of sustaining the trailer or truck
wheels. Firmly secure the vehicle to the truck or
trailer and lock the wheels in the position used by
the carrier.
-- Electric heaters, battery--chargers and similar
equipment must only be powered by auxiliary
power supplies with efficient ground insulation to
avoid electrical shock hazards.
-- Always use suitable hoisting or lifting devices
when raising or moving heavy parts.
-- Take extra care if bystanders are present.
-- Never pour petrol or diesel oil into open, wide or
low containers.
-- Never use gasoline, diesel oil or other
inflammable liquids as cleaning agents. Use
non--inflammable, non--toxic commercially
available solvents.
-- Wear safety goggles with side guards when
cleaning parts with compressed air.
-- Limit the air pressure to a maximum of 2.1 bar,
according to local regulations.
-- Do not run the engine in confined spaces without
suitable ventilation.
-- Do not smoke, use naked flames, or cause
sparks in the area when fuel filling or handling
highly inflammable liquids.
-- Never use naked flames for lighting when
working on the machine or checking for leaks.
-- All movements must be carried out carefully
when working under, on or near the vehicle.
Wear suitable safety clothing, i.e., hard hat,
safety goggles and special shoes.
-- When carrying out checks with the engine
running, request the assistance of an operator in
the driver’s seat. The operator must maintain
visual contact with the service technician at all
times.
-- If operating outside the workshop, position the
vehicle on a flat surface and lock in position. If
working on a slope, lock the vehicle in position.
Move to a flat area as soon as is safely possible.
-- Damaged or bent chains or cables areunreliable.
Do not use them for lifting or towing. Always use
suitable protective gloves when handling chains
or cables.
-- Chains should always be safely secured. Make
sure that the hitch--up point is capable of
sustaining the load in question. Keep the area
near the hitch--up point, chains or cables free of
all bystanders.
-- Maintenance and repair operations must be
carried out in a CLEAN and DRY area. Eliminate
any water or oil spillage immediately.
-- Do not create piles of oil or grease--soaked rags
as they represent a serious fire hazard. Always
place them into a metal container.
Before starting the tractor or its attachments,
check, adjust and block the operator’s seat. Also
check that there are no persons within the
vehicle or implement range of action.
-- Empty pockets of all objects that may fall
unobserved into the vehicle parts.
-- In the presence of protruding metal parts, use
protective goggles or goggles with side guards,
helmets, special footwear and gloves.
-- When welding, use protective safety devices:
tinted safety goggles, helmets, special overalls,
gloves and footwear. All persons present in the
area where welding is taking place must wear
tinted goggles. NEVER LOOK DIRECTLY AT
THE WELDING ARC WITHOUT SUITABLE
EYE PROTECTION.
-- Metal cables tend to fray with repeated use.
Always use suitable protective devices (gloves,
goggles, etc.) when handling cables.
-- Handle all parts with great care. Do not put your
hands or fingers between moving parts. Always
wear suitable safety clothing -- safety goggles,
gloves and shoes.

84419878A -- 06 -- 2011
STARTING
-- Never run the engine in confined spaces that are
not equipped with adequate ventilation for
exhaust gas extraction.
-- Never place the head, body, limbs, feet, hands or
fingers near fans or rotating belts.
ENGINE
-- Always loosen the radiator cap slowly before
removing it to allow any remaining pressure in
the system to be discharged. Filling up with
coolant should only be carried out with theengine
stopped or idling (if hot).
-- Never fill up with fuel when the engine is running,
especially if hot, in order to prevent the outbreak
of fire as a result of fuel spillage.
-- Never check or adjust fan belt tension when the
engine is running.
Never adjust the fuel injection pump when the
vehicle is moving.
-- Never lubricate the vehicle when the engine is
running.
ELECTRICAL SYSTEMS
-- If it is necessary to use auxiliary batteries,
remember that both ends of the cables must be
connected as follows: (+) with (+) and (--) with(--).
Avoid short--circuiting the terminals. GAS
RELEASED FROM BATTERIES IS HIGHLY
INFLAMMABLE. During charging, leave the
battery compartment uncovered to improve
ventilation. Never check the battery charge using
”jumpers” (metal objects placed on the
terminals). Avoid sparks or flames near the
battery zone. Do no smoke to prevent explosion
hazards.
-- Before servicing operations, check for fuel or
current leaks. Eliminate any eventual leaks
before proceeding with work.
-- Never charge batteries in confined spaces. Make
sure that there is adequate ventilation in order to
prevent accidental explosion hazards as a result
of the accumulation of gases released during
charging operations.
-- Always disconnect the batteries before
performing any kind of servicing on the electrical
system.
HYDRAULIC SYSTEMS
-- A liquid leaking from a tiny hole may be almost
invisible but, at the same time, be powerful
enough to penetrate the skin. Therefore, use a
piece of cardboard or wood for this purpose.
NEVER DO IT WITH YOUR HANDS: If anyliquid
penetrates skin tissue, call for medical aid
immediately. Failure to treat this condition with
correct medical procedure may result in serious
infection or dermatosis.
-- In order to check the pressure in the system use
suitable instruments.
WHEELS AND TYRES
-- Make sure that the tyres are correctly inflated at
the pressure specified by the manufacturer.
Periodically check possible damages to the rims
and tyres.
-- Stand away from (at the side of) the tyre when
checking inflation pressure.
-- Only check pressure when the vehicle is
unloaded and the tyres are cold, to avoid
incorrect readings as a result of over--pressure.
Do not reuse parts of recovered wheels as
improper welding, brazing or heating may
weaken the wheel and make it fail.
-- Never cut or weld a rim mounted with an inflated
tyre.
-- To remove the wheels, lock both the front and
rear vehicle wheels. After having raised the
vehicle, position supports underneath, according
to regulations in force.
-- Deflate the tyre before removing any object
caught in the tyre tread.
-- Never inflate tyres using inflammable gases, as
this may result in explosions and injury to
bystanders.
REMOVAL AND RE--FITTING
-- Lift and handle all heavy parts using suitable
hoisting equipment. Make sure that parts are
sustained by appropriate hooks and slings. Use
the hoisting eyebolts for lifting operations. Extra
care should be taken if persons are present near
the load to be lifted.
-- Handle all parts with carefully. Do not put your
hands or fingers between parts. Wear suitable
safety clothing, i.e. safety goggles, gloves and
footwear.
-- Avoid twisting chains or metal cables. Always
wear safety gloves when handling cables or
chains.

4 SECTION 10 -- ENGINE -- CHAPTER 1
84419878A -- 06 -- 2011
Op. 10 001 10
ENGINE Removal--Installation
DANGER
Lift and handle all heavy parts using suitable lifting
equipment.
Make sure that assemblies or parts are supported by
means of suitable slings and hooks. Ensure that
no--one is in the vicinity of the load to be lifted.
ATTENTION
Use suitable tools to align the holes. NEVER USE
FINGERS OR HANDS.
1. Carry out operation 90 150 10 -- Cab assembly
with platform (do only the removal -- see sect. 90,
chapter 1).
2. Extract the fixing pin and remove the ballast
weights (1); unscrew the fixing screws and
recover the ballast support (2).
1
3. Position a suitable container under the rear
transmission, unscrew the plug (1) and drain off
the oil from the transmission.
NOTE: Consider that the prescribed quantity is:
35 litres for mechanical transmissions or 40 litres for
hydraulic transmissions.
2
4. Disconnect the pipes (2 and 3) from the central
auxiliary control valves, unscrew the bracket
fixing screws (1) supporting the control valves
and remove the unit.
3

SECTION 10 -- ENGINE -- CHAPTER 1 5
84419878A -- 06 -- 2011
5. Disconnect the following pipes from the central
auxiliary control valves: delivery (1) to the rear
auxiliary control valves and return (2) to the
transmission box.
4
6. Unscrew the relative retaining bolts and detach
the cab right--hand support (1).
Do this on both sides.
5
7. Disconnect and detach the pipes (1 and 2)
connecting the power shuttle control valve to the
cooler.
6
8. Disconnect the central auxiliary control valve
connection line (5).
9. Disconnect the rear auxiliary control valve
connection line (1).
10. Disconnect the four--wheel drive engagement
control line (4).
11. Disconnect the PTO control line (2).
12. Disconnect the rear transmission lubrication line
(3).
7

84419878A -- 06 -- 2011
13. Disconnect the intake pipe (1) from the rear
transmission box and from the filter support,
remove this pipe.
8
14. Unscrew the front, middle and rear fasteners,
and detach the propeller shaft guard (1).
9
15. Remove the circlip (3) and move the sleeve (2)
back to free it from the splined output shaft of the
front axle (1), do this on the rear sleeve too.
10
16. Unscrew bolts (2) and remove the propeller shaft
(1).
11

84419878A -- 06 -- 2011
17. Disconnect the pipes: (1) connecting to the
hydraulic pump, (2) connecting to the central
auxiliary control valves and (4) hydraulic pump
inlet.
18. Unscrew the retaining bolts and remove the filter
(3) and support.
12
19. Set a fixed stand under the clutch box, connect
the rear of the engine to the hoist, unscrew the
fixing screws (1) and detach the engine together
with the front axle from the clutch box.
13
20. Disconnect the pipes (1) connecting to the
transmission oil cooler.
14
21. Disconnect the radiator top sleeve (2).
22. Disconnect the sleeve (1) connecting the
turbocharger to the air filter.
23. Unscrew the retaining bolts and detach the
maxi--fuse support bracket (3).
15

84419878A -- 06 -- 2011
24. Disconnect the electrical connection (1) from the
filter/dryer (2).
16
25. Unscrew the retaining bolts and detach the
bracket (1) locking the radiator to the engine.
17
26. Disconnect the fittings (2) to separate the rigid
pipes from the flexible hoses.
27. Detach the bracket (1) fixing the steering cylinder
control lines.
18
28. Unscrew the bolt fastening the bracket (1) to the
engine.
19

84419878A -- 06 -- 2011
29. Disconnect the pipes (1 and 2) from the cab air
conditioning system compressor.
20
30. Set a fixed stand under the front of the front axle
support and one under the back of it.
31. Connect the engine to a chain (1) and to the
hoist.
21
32. Unscrew the bolts (1), on both sides, and remove
the engine.
33. Then rest the engine on an adequate support.
34. To re--fit the engine, proceed as follows:
ATTENTION
FINGERS OR HANDS.
22
-- Using a chain connect the engine to the hoist and
reattach it to the front axle support tightening the
screws to the prescribed torque.
-- Connect the pipes to the compressor of the cab
air conditioning system.
-- Using the appropriate bracket, secure the
maxi--fuse connecting cable.
-- Secure the steering cylinder control lines using
the relevant bracket.
-- Connect the steering cylinder control piping.
-- Position and secure the bracket retaining the
radiator to the engine.
-- Connect the electrical connection to the
filter/dryer.
-- Position and secure the maxi--fuse support
bracket.
-- Position and secure the sleeve connecting the
turbocharger to the air filter.
-- Position and secure the radiator upper sleeve.

84419878A -- 06 -- 2011
-- Position and connect the transmission oil cooler
connecting pipes.
-- Position the engine together with the front axle
and secure it to the clutch box tightening the
screws to the prescribed torque.
-- Position the oil filter, complete with support, and
secure it to the engine.
-- Connect the pipes for the: hydraulic pump inlet,
central auxiliary control valves connection and
hydraulic pump connection.
-- Position the propeller shaft, secure the central
support, slide the two front and rear sleeves and
secure them with the circlips.
-- Position the propeller shaft guard and secure it.
-- Position the pipe drawing oil from the
transmission and secure it.
-- Connect the rear transmission lubrication line.
-- Connect the PTO control line.
-- Connect the four--wheel drive engagement
control line.
-- Connect the rear auxiliary control valve
connection line.
-- Connect the central auxiliary control valve
connection line.
-- Connect the pipes connecting the power shuttle
control valve to the cooler.
-- Position and secure the right and left supports of
the cab.
-- Connect the central auxiliary control valve
connection line to the rear auxiliary control
valves.
-- Connect the central auxiliary control valve return
line to the rear transmission.
-- Position and secure the ballast support.
-- Position and secure the ballast.
-- Carry out operation 90 150 10 -- Cab with
platform unit (perform installation only).
-- Screw the plug into the rear transmission box
and fill with oil (see sect. 00, page 6 for
prescribed product and quantity).

84419878A -- 06 -- 2011
Op. 10 216 40
FUEL TANK Removal--Installation
ATTENTION
Handle all parts with care. Do not put your hands or
fingers between parts. Wear the prescribed safety
clothing, including goggles, gloves and safety
footwear.
Proceed as follows.
1. Block the front axle with wooden chocks (1). Do
this on both sides.
23
2. Raise the rear of the tractor, position a fixed
stand under the rear transmission box, unscrew
the relevant fixing screws and detach the left rear
wheel (1).
24
3. Unscrew the plug (1) and drain off the fuel from
the main tank.
Consider that the total capacity is 90 litres.
25

84419878A -- 06 -- 2011
4. Unscrew the relevant retaining bolts and remove
the left steps (1).
5. Unscrew the two fuel tank fixing clamps (3).
6. Unscrew the screws fixing the bottom guard (2)
and detach it.
26
7. Unscrew the clamps (1 and 3) and detach the
fuel return and inlet lines.
8. Disconnect the electrical connection (2) of the
fuel gauge.
27
9. Unscrew the two brackets (1 and 2) fixing the fuel
return and inlet pipes, finally remove the fuel
tank.
10. To refit the fuel tank, proceed as follows.
ATTENTION
FINGERS OR HANDS.
-- Position and secure the tank fuel return and fuel
inlet lines.
-- Secure the tank fuel return and fuel inlet lines
using the appropriate brackets.
-- Connect the electrical connection of the fuel
gauge.
-- Position the fuel tank and secure it with the
clamps
-- Position and secure the bottom guard of the fuel
tank.
-- Position and secure the left steps.
-- Position and secure the left rear wheel.
28

84419878A -- 06 -- 2011
Op. 10 216 10
ENGINE COOLANT RADIATOR
Removal--Installation
ATTENTION
Handle all parts with care. Do not put your hands or
fingers between parts. Wear the prescribed safety
clothing, including goggles, gloves and safety
footwear.
Proceed as follows.
1. Carry out operation 90 100 22 -- Bonnet (perform
removal only).
2. Carry out operation 50 200 72 -- Air--conditioning
system condenser (perform removal only).
3. Carry out operation 21 109 40 -- Transmission oil
cooler (perform removal only).
4. Loosen the clamp, detach the sleeve (1) from the
radiator and drain off the coolant 29
5. Disconnect the air intake sleeve (1).
30
6. Disconnect the sleeve (1) from the air filter and
from the turbocharger.
7. Disconnect the sleeve (2) from the radiator.
31

84419878A -- 06 -- 2011
8. Disconnect: the pipes (1) and the electrical
connection (2) from the filter/dryer.
32
9. Detach the engine coolant expansion tank (1).
33
10. Unscrew the top and bottom screws fixing the
bracket (1) supporting the air filter and recover
the unit together with the filter/dryer.
34
11. Disconnect the bracket (1) and disconnect the
pipe (2) from the cab air conditioning system
compressor.
35

84419878A -- 06 -- 2011
12. Unscrew the related bolts and remove the
bracket (1) fixing the radiator to the engine.
13. On the right side, detach the brackets fixing the
pipes of the air--conditioning system to the
engine.
36
14. Detach the maxi--fuse support bracket (2) and
unscrew the relevant screws to free the shroud
(1) from the engine coolant radiator.
37
15. Unscrew the two bolts (1) and remove the engine
coolant radiator.
16. Install the engine coolant radiator considering
the following warnings.
ATTENTION
FINGERS OR HANDS.
-- Position and secure the radiator on the front axle
support.
-- Secure: the shroud, maxi--fuse support bracket
and the brackets fixing the air--conditioning
pipes.
-- Position and secure the radiator retaining
bracket to the engine.
-- Connect and secure the piping to the
compressor.
-- Position and secure the air filter unit and
filter/dryer.
-- Position the expansion tank.
-- Connect: the pipes and the electrical connection
to the filter/dryer.
-- Connect the air filter sleeves.
-- Connect the sleeves to the radiator.
-- Connect the air intake sleeve.
38
-- Carry out operation 21 109 40 Transmission oil
cooler (perform installation only).
-- Carry out operation 50 200 72 Air--conditioning
system condenser (perform installation only).
-- Carry out operation 90 100 22 -- Bonnet (perform
installation only).
-- Fill up the engine cooling system (see page 6,
sect. 0 for prescribed product and quantity).

84419878A -- 06 -- 2011
ADJUSTING THE THROTTLE CONTROL
CABLE
ATTENTION
FINGERS OR HANDS.
Proceed as follows.
1. Connect the throttle control cable (2) to the
injection pump and tighten the nut (1) to eliminate
the play in the cable.
39
2. Fully tighten the throttle control pedal limit stop
screw (1).
40
3. Apply a load (P) of 10 daN ± 1 on the accelerator
control pedal, tighten the limit stop screw (1) until
contact is made with the platform and lock it by
means of the relevant lock nut.
41

SECTION 18 -- CLUTCH -- CHAPTER 1 1
84419878A -- 06 -- 2011
SECTION 18 -- CLUTCH
Chapter 1 -- Clutch
CONTENTS
Section Description Page
18 000 General specifications 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Torque settings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special tools 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sections 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 110 10 Clutch -- Removal--Installation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 110 30 Dual disk clutch 11”/11” Test bench overhaul 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 100 40 Clutch adjustments 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LUK 11”/11” CLUTCH -- GENERAL SPECIFICATIONS
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . single disk, dry plate dual clutch
unit
Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . control: pedal operation for main
clutch and hand lever for power
take--off clutch
Engagement and release mechanism . . . . . . . . . . . . . . . . . . . . . . . single Belleville spring disc
Driven plate lining material for main transmission clutch: . . . . . . . cerametallic
Driven plate lining material for PTO clutch . . . . . . . . . . . . . . . . . . . organic
Driven disc thickness:
-- main clutch (9, fig. 2): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . mm 10.2 ÷ 10.8
-- PTO clutch (11, fig. 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ” 7.4 ÷ 7.8
-- wear limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ” see pages 10 and 11
Release lever coplanarity adjustment . . . . . . . . . . . . . . . . . . . . . . . see page 11
Clutch control adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see page 12

2 SECTION 18 -- CLUTCH -- CHAPTER 1
84419878A -- 06 -- 2011
TORQUE SPECIFICATIONS
PARTS TO BE TIGHTENED Thread
Tightening torque
PARTS TO BE TIGHTENED Thread
Nm kgm
Clutch casing/engine retaining bolts . . . . . . . . . . . . . . . . . . . . . . . . . M 12 x 1.25 117 ÷ 129 11.9 ÷ 13.1
Screws (C1) fixing clutch box to the rear transmission box . . . . . M 12 x 1.25 117 ÷ 129 11.9 ÷ 13.1
Screw (C2) securing levers to release command fork (7, fig. 1) . M 16 x 1.5 136 ÷ 165 13.9 ÷ 16.9
11”/11” clutch/flywheel retaining bolts (C3) . . . . . . . . . . . . . . . . . . . M 8 x 1.25 20 ÷ 25 2 ÷ 2.5
1

84419878A -- 06 -- 2011
TOOLS
Warning -- The operations described in this section
can only be carried out with ESSENTIAL tools
indicated by an (X).
To work safely and efficiently and obtain the best
results, it is also necessary to use the recommended
specific tools listed below and certain other tools,
which are to be made according to the drawings
included in this manual.
List of specific tools required for the various
operations described in this section.
X 380001612 Pin for centering and adjustment of
11”/11” clutches.
X 380000293 Clutch adjustment gauge (with
380001612).
380000256 Set of wrenches for adjustment of
levers in 11”/11” LUK clutches.
Longitudinal section of 11”/11” LUK clutch
1. PTO clutch release lever adjuster screw.
2. PTO clutch release levers.
3. Main clutch release levers.
4. Main clutch disk.
5. Main clutch release lever adjuster.
6. PTO clutch disk.
7. Belleville spring disk.
D = 100.5 mm Nominal distance of the levers (8) from the
clutch/engine flywheel mating surface.
D1 = 140 mm. Nominal distance of the levers (4)
from the clutch/engine flywheel mating surface.
NOTE: During installation, apply sealing compound
to surfaces X as shown in Section 21, Chapter 1,
page 22.
2

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

84419878A -- 06 -- 2011
CLUTCH TROUBLESHOOTING
Problems Possible causes Solutions
The clutch slips 1. Worn disks 4 and 6, page 3, on
pressure plates and flywheel.
Check and compare the data given on
the pages indicated, replace any
parts which are worn up to or over the
limit and adjust levers and clutch con-
trol linkage.
2. Belleville spring disk (7, page
3) stretched or damaged.
Replace the Belleville spring.
3. Oil or grease contaminating
the friction lining of disks 4 and
6, page 3).
Replace the disks, identify and elimi-
nate the source of the lubricant inside
the clutch housing and thoroughly
clean the friction surfaces.
The clutch jerks 1. Partial seizure of the external
control linkage.
Check rod pivots and lubricate.
2. Clutch disk (4, page 3) defor-
med.
Replace the disk and adjust the clutch
control lever.
3. Clutch disk (4, page 3) with
torsion springs damaged or
with hub rivets loose.
Replace disk.
4. Oil or grease contaminating
the disks friction material (4
and 6, page 3).
Replace the disks, identify and elimi-
nate the source of the lubricant inside
the clutch housing and thoroughly
clean the friction surfaces.
Clutch sticks and drags 1. Clutch disks (4 and 6, page 3)
deformed.
Replace and adjust disks.
2. Seizure of external control lin-
kage.
Check, replace faulty parts and lubri-
cate.
3. Controls incorrectly adjusted. Adjust the controls (see page 12).
Clutch noisy when engaged
and/or disengaged.
1. Thrust bearing worn. Replace bearing
2. Clutch disk (4, page 3) with
torsion springs faulty.
Replace disk.
Clutch pedal too stiff 1. Partial seizure of the external
control linkage.
Check rod pivots and lubricate.
2. Partial seizure of pedal pivot. Check pivot and lubricate.

84419878A -- 06 -- 2011
Op. 18 110 10
CLUTCH Removal--Refitting
DANGER
Lift and handle all heavy parts using suitable lifting
equipment.
Make sure that assemblies or parts are supported by
means of suitable slings and hooks. Ensure that
no--one is in the vicinity of the load to be lifted.
ATTENTION
FINGERS OR HANDS.
Proceed as follows.
1. Carry out operation 10 001 10 Engine, only
removal (see sect. 10).
2. Using tool 380001612 (1), unscrew the retaining
bolts and remove the clutch (2).
3. To install the clutch on the engine flywheel,
proceed as follows.
ATTENTION
FINGERS OR HANDS.
-- Apply the torque settings listed on page 2.
27785
3
-- Before refitting the engine to the clutch box
carefully clean the mating surfaces and apply
sealing compound (approximately 2 mm
diameter), according to the diagram shown in
Section 21, Chapter 1, on page 22.
-- Refit the clutch to the flywheel, using tool
380001612.
-- Carry out operation 10 001 10 Engine, only
installation (see sect. 10).

84419878A -- 06 -- 2011
Op. 18 110 30
11”/11” DUAL DISK CLUTCH --
Test bench overhaul
ATTENTION
FINGERS OR HANDS.
Proceed as follows.
1. Unscrew the three PTO clutch lever adjustment
nuts (1).
24791
1
4
2. Recover the pressure plate (1) with the three coil
springs (2) and the three washers.
24792
1
2
5
3. Position three clamps (1) at intervals of 120° on
the clutch body and gradually and carefully
squeeze the Belleville spring disk.
24793
1
6
4. Extract the six spring retaining pins (1) from their
seats.
24794
1
7

84419878A -- 06 -- 2011
5. Remove the three clamps and extract the
Belleville spring disk (1).
24975
1
8
6. Loosen the three locknuts (1) on the main clutch
lever adjustment screws.
24976
1
9
7. Remove the three main clutch lever adjustment
screws (1).
24977
1
10
8. Extract the main clutch pressure plate (1).
24978
1
11

84419878A -- 06 -- 2011
9. Extract the main clutch disk (1).
24979
1
12
10. Remove the springs (1) on the PTO clutch
control levers.
24980
1
13
11. Extract the pivot pins (1) on the PTO clutch
control levers.
24981
1
14
12. Remove the springs (1) on the main clutch
control levers.
24982
1
15

Case ih farmall 75 c tractor service repair manual

More Related Content

What's hot (6)

Similar to Case ih farmall 75 c tractor service repair manual (20)

More from jfdjjskfkksmemm (20)

Recently uploaded (20)

Case ih farmall 75 c tractor service repair manual