Case ih farmall 85 a tractor service repair manual

Part number 48194628
1/1
FARMALL 85A
FARMALL 95A
FARMALL 105A
FARMALL 115A
Tractor
SERVICE MANUAL
FARMALL 85A
FARMALL 95A
FARMALL 105A
FARMALL 115A
Tractor
Part number 48194628
English
September 2017
© 2017 CNHI International. All Rights Reserved.
SERVICEMANUAL

Contents
INTRODUCTION
Engine....................................................................................... 10
[10.501] Exhaust Gas Recirculation (EGR) exhaust treatment.............................. 10.1
Clutch ....................................................................................... 18
[18.110] Clutch and components ............................................................ 18.1
Transmission.............................................................................. 21
[21.114] Mechanical transmission ........................................................... 21.1
[21.140] Mechanical transmission internal components..................................... 21.2
[21.112] Power shuttle transmission......................................................... 21.3
[21.154] Power shuttle transmission internal components .................................. 21.4
[21.120] Gearbox ............................................................................ 21.5
[21.160] Creeper ............................................................................ 21.6
[21.162] Reverser ........................................................................... 21.7
Four-Wheel Drive (4WD) system .................................................. 23
[23.202] Electro-hydraulic control ........................................................... 23.1
Front axle system ....................................................................... 25
[25.100] Powered front axle ................................................................. 25.1
[25.102] Front bevel gear set and differential ............................................... 25.2
[25.108] Final drive hub, steering knuckles, and shafts ..................................... 25.3
[25.400] Non-powered front axle ............................................................ 25.4
Rear axle system........................................................................ 27
[27.100] Powered rear axle.................................................................. 27.1
[27.106] Rear bevel gear set and differential................................................ 27.2
[27.124] Final drive hub, steering knuckles, and shafts ..................................... 27.3
Power Take-Off (PTO)................................................................. 31
[31.101] Rear mechanical control ........................................................... 31.1
48194628 27/09/2017

Brakes and controls .................................................................... 33
[33.202] Hydraulic service brakes ........................................................... 33.1
[33.220] Trailer brake hydraulic control...................................................... 33.2
[33.224] Trailer brake pneumatic control .................................................... 33.3
Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.104] Fixed displacement pump.......................................................... 35.2
[35.525] Auxiliary hydraulic valves and lines ................................................ 35.3
[35.100] Main lift system..................................................................... 35.4
Steering..................................................................................... 41
[41.200] Hydraulic control components...................................................... 41.1
[41.206] Pump ............................................................................... 41.2
[41.216] Cylinders ........................................................................... 41.3
Wheels...................................................................................... 44
[44.511] Front wheels........................................................................ 44.1
Cab climate control ..................................................................... 50
[50.200] Air conditioning..................................................................... 50.1
Electrical systems....................................................................... 55
[55.000] Electrical system ................................................................... 55.1
[55.100] Harnesses and connectors......................................................... 55.2
[55.525] Cab engine controls................................................................ 55.3
[55.015] Engine control system.............................................................. 55.4
[55.201] Engine starting system ............................................................. 55.5
[55.301] Alternator........................................................................... 55.6
[55.302] Battery.............................................................................. 55.7
[55.202] Cold start aid ....................................................................... 55.8
[55.011] Fuel tank system ................................................................... 55.9
[55.010] Fuel injection system............................................................. 55.10
48194628 27/09/2017

[55.014] Engine intake and exhaust system............................................... 55.11
[55.013] Engine oil system ................................................................ 55.12
[55.640] Electronic modules ............................................................... 55.13
[55.024] Transmission control system..................................................... 55.14
[55.048] Rear Power Take-Off (PTO) control system ..................................... 55.15
[55.049] Front Power Take-Off (PTO) control system ..................................... 55.16
[55.512] Cab controls...................................................................... 55.17
[55.130] Rear three-point hitch electronic control system ................................. 55.18
[55.408] Warning indicators, alarms, and instruments .................................... 55.19
Platform, cab, bodywork, and decals............................................. 90
[90.150] Cab................................................................................. 90.1
48194628 27/09/2017

INTRODUCTION
48194628 27/09/2017
1

INTRODUCTION
Safety rules
Pay attention to this symbol
This warning symbol points out important messages involving personal safety. Carefully read the
safety rules contained herein and follow advised precautions to avoid potential hazards and safeguard
your safety and personal integrity. In this manual you will find this symbol together with the following
key-words:
WARNING – It gives warning about improper repair operations and deriving potential consequences
affecting the service technician’s personal safety.
DANGER – It gives specific warning about potential dangers for personal safety of the operator or other
persons directly or indirectly involved.
To prevent accidents
Most accidents and personal injuries taking place in workshops are due from non-observance of some simple and
essential prudential rule and safety precautions. For this reason, IN MOST CASES THEY CAN BE AVOIDED. It
suffices to foresee possible causes and act consequently with necessary caution and care.
The possibility that an accident might occur with any type of machines should not be disregarded, no matter how well
the machine in question was designed and built.
A wise and careful service technician is the best precautions against accidents.
Careful observance of this only basic precaution would be enough to avoid many severe accidents.
DANGER: Never carry out any cleaning, lubrication or maintenance operations when the engine is running.
Safety rules
Generalities
• Carefully follow specified repair and maintenance procedures.
• Do not wear rings, wristwatches, jewels, unbuttoned or flapping clothing such as ties, torn clothes, scarves, open
jackets or shirts with open zips which could get hold into moving parts. We advise to use approved safety clothing
such as anti-slipping footwear, gloves, safety goggles, helmets, etc.
• Never carry out any repair on the machine if someone is sitting on the operator’s seat, except if they are certified
operators to assist in the operation to be carried out.
• Never operate the machine or use attachments from a place other than sitting at the operator’s seat.
• Never carry out any operation on the machine when the engine is running, except when specifically indicated.
• Stop the engine and ensure that all pressure is relieved from hydraulic circuits before removing caps, covers, valves,
etc.
• All repair and maintenance operations should be carried out with the greatest care and attention.
• Service stairs and platforms used in a workshop or in the field should be built in compliance with the safety rules in
force.
• Disconnect the batteries and label all controls to warn that the tractor is being serviced. Block the machine and all
equipment which should be raised.
• Never check or fill fuel tanks and accumulator batteries, nor use starting liquid if you are smoking or near open
flames as such fluids are flammable.
• Brakes are inoperative when they are manually released for maintenance purposes. In such cases, the machine
should be kept constantly under control using blocks or similar devices.
• The fuel filling gun should remain always in contact with the filler neck. Maintain this contact until the fuel stops
flowing into the tank to avoid possible sparks due to static electricity buildup.
• Use exclusively specified towing points for towing the tractor. Connect parts carefully. Ensure that foreseen pins
and/or locks are steadily fixed before applying traction. Do not stop near towing bars, cables or chains working
under load.
48194628 27/09/2017
5

INTRODUCTION
• To transfer a failed tractor, use a trailer or a low loading platform trolley if available.
• To load and unload the machine from the transportation mean, select a flat area providing a firm support to the
trailer or truck wheels. Firmly tie the machine to the truck or trailer platform and block wheels as required by the
forwarder.
• For electrical heaters, battery-chargers and similar equipment use exclusive auxiliary power supplies with a efficient
ground to avoid electrical shock hazard.
• Always use lifting equipment and similar of appropriate capacity to lift or move heavy components.
• Pay special attention to bystanders.
• Never pour gasoline or diesel oil into open, wide and low containers.
• Never use gasoline, diesel oil or other flammable liquids as cleaning agents. Use nonflammable nontoxic propri-
etary solvents.
• Wear protection goggles with side guards when cleaning parts using compressed air.
• Do not exceed a pressure of 2.1 bar (30.45 psi), in accordance with local regulations.
• Do not run the engine in a closed building without proper ventilation.
• Do not smoke, use open flames, cause sparks in the nearby area when filling fuel or handling highly flammable
liquids.
• Do not use flames as light sources when working on a machine or checking for leaks.
• Move with caution when working under a tractor, and also on or near a tractor. Wear proper safety accessories:
helmets, goggles and special footwear.
• During checks which should be carried out with the engine running, ask an assistant to seat at the operator’s seat
and keep the service technician under visual control at any moment.
• In case of operations outside the workshop, drive the tractor to a flat area and block it. If working on an incline
cannot be avoided, first block the tractor carefully. Move it to a flat area as soon as possible with a certain extent
of safety.
• Ruined or plied cables and chains are unreliable. Do not use them for lifting or trailing. Always handle them wearing
gloves of proper thickness.
• Chains should always be safely fastened. Ensure that fastening device is strong enough to hold the load foreseen.
No persons should stop near the fastening point, trailing chains or cables.
• The working area should be always kept CLEAN and DRY. Immediately clean any spillage of water or oil.
• Do not pile up grease or oil soaked rags, as they constitute a great fire hazard. Always place them into a metal
container. Before starting the tractor or its attachments, check, adjust and block the operator’s seat. Also ensure
that there are no persons within the tractor or attachment operating range.
• Do not keep into your pockets any object which might fall unobserved into the tractor’s inner compartments.
• Whenever there is the possibility of being reached by ejected metal parts or similar, use protection eye mask or
goggles with side guards, helmets, special footwear and heavy gloves.
• Wear suitable protection such as tinted eye protection, helmets, special clothing, gloves and footwear whenever it is
necessary to carry out welding procedures. All persons standing in the vicinity of the welding process should wear
tinted eye protection. NEVER LOOK AT THE WELDING ARC IF YOUR EYES ARE NOT SUITABLY PROTECTED.
• Metal cables with the use get frayed. Always wear adequate protections (heavy gloves, eye protection, etc.)
• Handle all parts with the greatest caution. Keep your hands and fingers far from gaps, moving gears and similar.
Always use approved protective equipment, such as eye protection, heavy gloves and protective footwear.
Start up
• Never run the engine in confined spaces which are not equipped with adequate ventilation for exhaust gas extrac-
tion.
• Never bring your head, body, arms, legs, feet, hands, fingers near fans or rotating belts.
48194628 27/09/2017
6

SERVICE MANUAL
Engine
Farmall® 105A
Farmall® 115A
Farmall® 85A
Farmall® 95A
48194628 27/09/2017
10

Engine - Exhaust Gas Recirculation (EGR) exhaust treatment
Diesel Particulate Filters (DPF) - Remove
1. Raise the bonnet, disconnect the headlights connector
from the engine cable. Remove the hood. See Trailer
brake pneumatic control - Remove (33.224).
NOTE: Remove the hinge from the support leaving this
under the bonnet.
2. Remove the side panels on both sides.
ANIL15TRO1943AB 1
3. Loosen the clamp of the connection pipe (1) between
the air cleaner (3) and turbine, unscrew the retaining
screws of the air intake pipe (2) then slide it towards
the front so that it comes out of the filter inlet. Then, af-
ter disconnecting the clogged filter sensor connection,
remove the filter from the bonnet support.
ANIL15TRO2012AB 2
4. Disconnect the connectors on the pressure differential
sensor (1), on the two temperature sensors, and on
the lambda sensor. Loosen the system heat shield (2).
Position everything on the left-hand side of the engine.
ANIL15TRO2016AB 3
5. Remove the bonnet support (1).
ANIL15TRO2010AB 4
48194628 27/09/2017
10.1 [10.501] / 11

6. Unscrew the pressure differential unit (1) with its pipes,
brackets, clamps and sensor.
7. Unscrew the temperature sensor (2).
ANIL15TRO1996AB 5
8. Unscrew the filter’s upper heat shield (1), the lower one
stays in position.
ANIL15TRO1997AB 6
9. Mark the filter as shown in the figure.
NOTE: The right-hand marking must include the first part
of the filter, the central part of the filter (1), and the clamp
that joins them (2). The left-hand marking will include the
central part, the left-hand part, and the clamp (3).
ANIL15TRO1998AB 7
10. Loosen the clamp (1) joining the muffler to the DPF
outlet pipe. The clamp (2) that keeps the outlet tube
of the filter parallel to the first section of the filter.
ANIL15TRO1999AB 8
48194628 27/09/2017
10.1 [10.501] / 12

11. Remove the left-hand clamp (1) fastening the filter to
the machine.
ANIL15TRO2000AB 9
12. Loosen the left-hand clamp (1) fastening the middle
and left parts of the filter.
ANIL15TRO2001AB 10
13. Remove the left-hand part of the filter (1), with the
clamp (2), retrieving the copper seal.
ANIL15TRO2002AB 11
14. Then, after you have loosened the right-hand clamp
(1), remove the central part of the filter (2).
ANIL15TRO2003AB 12
48194628 27/09/2017
10.1 [10.501] / 13

Diesel Particulate Filters (DPF) - Install
NOTE: For the torque settings please refer to, Diesel Par-
ticulate Filters (DPF) - Torque (10.501).
1. Re-assemble the central part of the DPF filter (2) with
the relevant clamp. Tighten the clamp (1), paying at-
tention to the orientation of the parts.
ANIL15TRO2003AB 1
2. Re-assemble the left-hand part of the DPF filter (1) with
the relevant clamp (2). Tighten the clamp, paying atten-
tion to the orientation of the parts.
NOTE: If the clamp and the seal are rusty or in a poor
condition, change the clamp and the seal.
ANIL15TRO2005AB 2
3. Reassemble the left-hand clamp (1) fastening the filter
on the cradle.
ANIL15TRO2006AB 3
4. Position the collar (1) fastening the filter pipe to the
muffler. Tighten it. Also tighten the top of the collar
(2) that fixes the pipe to the cradle.
ANIL15TRO2007AB 4
48194628 27/09/2017
10.1 [10.501] / 14

5. Re-fit the filter upper heat shield (1).
ANIL15TRO2008AB 5
6. Re-fit the temperature sensor (2) and the pressure dif-
ferential assembly (1), complete with brackets, clamps,
pipes, and sensor.
ANIL15TRO2009AB 6
7. Refit the hood support (1).
ANIL15TRO2010AB 7
8. Refit the system heat shield (2). Reconnect the pres-
sure sensor, lambda sensor, and pressure differential
sensor (1). Position the wire harness. If necessary, se-
cure the wire harness with straps.
ANIL15TRO2011AB 8
48194628 27/09/2017
10.1 [10.501] / 15

9. Fit the air cleaner (3) onto the hose (1) that connects
the air cleaner to the turbine. Then secure the hose to
the hood support with the relevant screws.
10. Tighten the clamp on the hose. Run the intake duct
(2) toward the filter. Then tighten it with the relevant
screws. Reconnect the connector to the clogged filter
sensor.
ANIL15TRO2012AB 9
11. Re-assemble the side panels (2) and the bonnet (1),
Trailer brake pneumatic control - Install (33.224).
48194628 27/09/2017
10.1 [10.501] / 16

Diesel Particulate Filters (DPF) - Remove - with support
1. Raise the hood. Disconnect the headlight connector
from the engine cable. Then, after you have secured
the hood to the hoist with a belt, remove the hood. See
Trailer brake pneumatic control - Remove (33.224).
2. Remove the side panels on both sides.
ANIL15TRO2013AB 1
3. With the controller for recovering the gas from the air-
conditioning circuit, recover the gas (1).
4. Disconnect the air conditioning pipes (1), on the control
panel side.
ANIL15TRO2014AB 2
5. Loosen the clamp (1) retaining the air cleaner/turbine
connection pipe. Loosen the bolts on the air intake pipe
(2). Then slide the pipe toward the front to make the
pipe come out of the air cleaner.
6. Disconnect the connector on the clogged filter sensor,
unscrew the filter (3) from the hood support and extract
it.
ANIL15TRO2015AB 3
7. Disconnect the connectors on the pressure differential
sensor (1), on the two temperature sensors, and on
the lambda sensor. Loosen the system heat shield (2).
Position everything on the left-hand side of the engine.
ANIL15TRO2016AB 4
48194628 27/09/2017
10.1 [10.501] / 17

8. Remove the complete hood support (1).
ANIL15TRO2017AB 5
9. In the gap to the left-hand side of the reservoir for the
brakes, behind the filter, remove the bolts (1) that join
the cross support (2) of the filter and the rear support
(3).
ANIL15TRO2018AB 6
10. Remove the brakes reservoir heat shield (1).
ANIL15TRO2019AB 7
11. Loosen the clamp (1) fastening the exhaust pipe to the
DPF filter.
ANIL15TRO2020AB 8
48194628 27/09/2017
10.1 [10.501] / 18

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

12. Using a belt, sling the muffler, at two points at least,
take up the slack with a hoist. Remove the bolts (2)
that secure the exhaust pipe (1) to the support (3).
Then extract all of the pipe from the right-hand side of
the tractor and put it down on a pallet on the ground.
ANIL15TRO2021AB 9
13. Put two eyebolts (1) on the screws retaining the upper
heat shield of the filter. Using a chain, hook on the filter
(2) and tension the chains.
ANIL15TRO2022AB 10
14. On the left-hand side, under the filter remove the two
screws (1) on the adjustment bushings (3) of the filter
left support (2).
NOTE: After taking out the screws, unscrew the bushings
so as to create a gap between the filter assembly and the
left support.
ANIL15TRO2023AB 11
15. On the right-hand side, loosen the clamp (1) that
secures the filter decoupler to the turbine. Move
the clamp toward the front. Take out the three hex
socket screws (2) fastening the right support (3) to
the transversal one.
NOTE: These screws have been fitted by the supplier and
a few drops of Loctite have been used to prevent them,
over time, from coming loose.
ANIL15TRO2024AB 12
48194628 27/09/2017
10.1 [10.501] / 19

16. Using the hoist, raise the filter, taking great care that
there are no wiring harnesses and tie--rods connected
or obstructing the passage, then rest the filter with the
cross support on a workbench.
NOTE: With the machine in these conditions it is possi-
ble to work on the engine, for example on the valve cover,
and, if the right-hand support is not removed, it is possible
to reassemble the filter without making any special adjust-
ments.
48194628 27/09/2017
10.1 [10.501] / 20

Case ih farmall 85 a tractor service repair manual

More Related Content

Similar to Case ih farmall 85 a tractor service repair manual (20)

More from ujsefksmemtyu (20)

Recently uploaded (20)

Case ih farmall 85 a tractor service repair manual