Case ih farmall 85 n with cab tier 3 tractor service repair manual pin z8jf17086 zcjf09425

Printed in U.S.A.
© 2016 CNH Industrial Italia S.p.A. All Rights Reserved.
Case IH is a trademark registered in the United States and many
other countries, owned by or licensed to CNH Industrial N.V.,
its subsidiaries or affiliates.
FARMALL®
75N / FARMALL®
85N / FARMALL®
95N /
FARMALL®
105N / FARMALL®
105V
Tier 3
FARMALL®
75N with cab PIN Z8JF19102 - ZCJF10907; FARMALL®
75N with cab PIN ZCJF06107 and above;
FARMALL®
75N without cab PIN Z9JF01865 - ZCJF07697; FARMALL®
75N without cab PIN ZCJF07813 and above;
FARMALL®
FARMALL®
FARMALL®
FARMALL®
95N without cab PIN ZCJF15989 and above
FARMALL®
105N with cab PIN ZBJF20417 and above; FARMALL®
FARMALL®
105V with cab PIN ZBJF20562 and above; FARMALL®
105V without cab PIN ZDJF09419 and above
Tractor
Part number 47888397
1st
edition English
July 2016
SERVICE MANUAL

SERVICE MANUAL
Farmall® 105N With cab [ZBJF20417 - ], Farmall® 105N Without cab
[ZCJF16900 - ], Farmall® 105V With Cab [ZBJF20562 - ], Farmall® 105V
Without cab [ZDJF09419 - ], Farmall® 75N With cab - Model Year 2012
[ZCJF06107 - ], Farmall® 75N With cab [Z8JF19102 - ZCJF10907], Farmall®
75N Without cab [Z9JF01865 - ZCJF07697], Farmall® 75N Without cab -
Model Year 2012 [ZCJF07813 - ], Farmall® 85N With cab - Model Year 2012
85N Without cab - Model Year 2012 [ZCJF16077 - ], Farmall® 85N Without
cab [Z9JF01936 - ZCJF10868], Farmall® 95N With cab - Model Year 2012
cab [Z9JF01090 - ZCJF05141]
47888397 08/07/2016
EN

Link Product / Engine
Product Market Product Engine
Farmall® 105N With cab
[ZBJF20417 - ]
North America F4CE9484
Farmall® 105N Without cab
[ZCJF16900 - ]
[Z8JF19102 - ZCJF10907]
North America F5AE9484B
[Z9JF01865 - ZCJF07697]
Farmall® 75N With cab - Model
Year 2012 [ZCJF06107 - ]
Farmall® 75N Without cab - Model
Year 2012 [ZCJF07813 - ]
[Z8JF17086 - ZCJF09425]
North America F5AE9484G
[Z9JF01936 - ZCJF10868]
Year 2012 [ZCJF08828 - ]
Year 2012 [ZCJF16077 - ]
[Z9JF00469 - ZCJF10732]
[Z9JF01090 - ZCJF05141]
Year 2012 [ZCJF13045 - ]
Year 2012 [ZCJF15989 - ]
Farmall® 105V With Cab
[ZBJF20562 - ]
Farmall® 105V Without cab
[ZDJF09419 - ]
47888397 08/07/2016

Contents
INTRODUCTION
Engine....................................................................................... 10
[10.001] Engine and crankcase ............................................................. 10.1
Clutch ....................................................................................... 18
[18.100] Clutch mechanical release control ................................................. 18.1
[18.104] Clutch hydraulic release control.................................................... 18.2
[18.110] Clutch and components ............................................................ 18.3
Transmission.............................................................................. 21
[21.114] Mechanical transmission ........................................................... 21.1
[21.130] Mechanical transmission external controls......................................... 21.2
[21.140] Mechanical transmission internal components..................................... 21.3
[21.112] Power shuttle transmission......................................................... 21.4
[21.134] Power shuttle transmission external controls ...................................... 21.5
[21.154] Power shuttle transmission internal components .................................. 21.6
[21.145] Gearbox internal components...................................................... 21.7
[21.160] Creeper ............................................................................ 21.8
[21.162] Reverser ........................................................................... 21.9
[21.168] Hi-Lo unit ......................................................................... 21.10
[21.182] Differential........................................................................ 21.11
Four-Wheel Drive (4WD) system .................................................. 23
[23.202] Electro-hydraulic control ........................................................... 23.1
[23.304] Four-Wheel Drive (4WD) gearbox ................................................. 23.2
[23.314] Drive shaft.......................................................................... 23.3
Front axle system ....................................................................... 25
[25.100] Powered front axle ................................................................. 25.1
[25.102] Front bevel gear set and differential ............................................... 25.2
47888397 08/07/2016

[25.108] Final drive hub, steering knuckles, and shafts ..................................... 25.3
[25.122] Axle suspension control............................................................ 25.4
[25.310] Final drives ......................................................................... 25.5
[25.400] Non-powered front axle ............................................................ 25.6
Rear axle system........................................................................ 27
[27.100] Powered rear axle.................................................................. 27.1
[27.106] Rear bevel gear set and differential................................................ 27.2
[27.120] Planetary and final drives .......................................................... 27.3
[27.126] Spur gear and final drives.......................................................... 27.4
Power Take-Off (PTO)................................................................. 31
[31.101] Rear mechanical control ........................................................... 31.1
Brakes and controls .................................................................... 33
[33.202] Hydraulic service brakes ........................................................... 33.1
[33.110] Parking brake or parking lock ...................................................... 33.2
[33.220] Trailer brake hydraulic control...................................................... 33.3
Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.300] Reservoir, cooler, and filters........................................................ 35.2
[35.104] Fixed displacement pump.......................................................... 35.3
[35.204] Remote control valves ............................................................. 35.4
[35.600] High flow hydraulics................................................................ 35.5
[35.100] Main lift system..................................................................... 35.6
[35.114] Three-point hitch control valve ..................................................... 35.7
[35.116] Three-point hitch cylinder .......................................................... 35.8
Hitches, drawbars, and implement couplings.................................. 37
[37.110] Rear three-point hitch .............................................................. 37.1
[37.108] Rear three-point hitch external controls............................................ 37.2
Steering..................................................................................... 41
47888397 08/07/2016

[41.101] Steering control .................................................................... 41.1
[41.200] Hydraulic control components...................................................... 41.2
Wheels...................................................................................... 44
[44.511] Front wheels........................................................................ 44.1
Cab climate control ..................................................................... 50
[50.100] Heating ............................................................................. 50.1
[50.104] Ventilation .......................................................................... 50.2
[50.200] Air conditioning..................................................................... 50.3
Electrical systems....................................................................... 55
[55.000] Electrical system ................................................................... 55.1
[55.100] Harnesses and connectors......................................................... 55.2
[55.201] Engine starting system ............................................................. 55.3
[55.301] Alternator........................................................................... 55.4
[55.302] Battery.............................................................................. 55.5
[55.202] Cold start aid ....................................................................... 55.6
[55.640] Electronic modules ................................................................. 55.7
[55.051] Cab Heating, Ventilation, and Air-Conditioning (HVAC) controls................... 55.8
[55.050] Heating, Ventilation, and Air-Conditioning (HVAC) control system................. 55.9
[55.047] Steering control system .......................................................... 55.10
[55.523] Cab hitch controls ................................................................ 55.11
[55.130] Rear three-point hitch electronic control system ................................. 55.12
[55.404] External lighting .................................................................. 55.13
[55.514] Cab lighting ...................................................................... 55.14
[55.511] Light harnesses .................................................................. 55.15
[55.408] Warning indicators, alarms, and instruments .................................... 55.16
[55.DTC] FAULT CODES.................................................................. 55.17
Platform, cab, bodywork, and decals............................................. 90
[90.110] Operator platform less cab ......................................................... 90.1
47888397 08/07/2016

[90.114] Operator protections ............................................................... 90.2
[90.150] Cab................................................................................. 90.3
[90.151] Cab interior......................................................................... 90.4
[90.154] Cab doors and hatches ............................................................ 90.5
[90.100] Engine hood and panels ........................................................... 90.6
[90.102] Engine shields, hood latches, and trims ........................................... 90.7
[90.160] Cab interior trim and panels........................................................ 90.8
47888397 08/07/2016

INTRODUCTION
47888397 08/07/2016
1

INTRODUCTION
Advice Important notice
All maintenance and repair work described in this manual must be performed exclusively by CASE IH service techni-
cians, in strict accordance with the instructions given and using any specific tools necessary. Anyone performing the
operations described herein without strictly following the instructions is personally responsible for any eventual injury
or damage to property.
47888397 08/07/2016
3

INTRODUCTION
Note to the Owner WARNINGS FOR AIR CONDITIONING SYSTEM
REPAIR OPERATIONS
Farmall® 105N With cab [ZBJF20417 - ] NA
Farmall® 105V With Cab [ZBJF20562 - ] NA
Farmall® 75N With cab - Model Year 2012 [ZCJF06107 - ] NA
Farmall® 75N With cab [Z8JF19102 - ZCJF10907] NA
Starting the system at low temperatures can damage the compressor. Only operate the air conditioner when the
engine is hot and the temperature inside the cab is at least 20 °C (68.00 °F).
When disconnecting the hoses, close the ends with plastic caps to prevent foreign matter and humidity from getting
inside the hoses.
Handle the thermostatic sensor carefully to avoid damage that may prevent efficient system operation.
Always use two spanners to unscrew the hose fittings to avoid twisting the fitting.
Do not use any type of engine oil to lubricate the compressor and the system.
Never leave the compressor oil container open, always make sure that it is tightly closed. If left exposed the oil will
absorb humidity from the air and may, subsequently, damage the system.
Do not transfer compressor oil from the original container to another container.
Do not introduce any additives to the compressor oil. Any additional substances could contain elements which are
incompatible with the chemical base of the refrigerant and thus alter its characteristics.
Check that the thermostatic sensor is correctly inserted in the fins on the evaporator to ensure efficient system oper-
ation.
47888397 08/07/2016
4

INTRODUCTION
Safety rules SAFETY REGULATIONS
TO PREVENT ACCIDENTS
Most accidents or injuries that occur in workshops are the result of non--observance of simple and fundamental safety
regulations.
For this reason, IN MOST CASES THESE ACCIDENTS CAN BE AVOIDED: by foreseeing possible causes and con-
sequently acting with the necessary caution and care.
Accidents may occur with all types of vehicle, regardless of how well it was designed and built.
A careful and judicious service technician is the best guarantee against accidents.
Precise observance of the most basic safety rule is normally sufficient to avoid many serious accidents.
DANGER: Never carry out any cleaning, lubrication or maintenance operations when the engine is running.
GENERAL
• Carefully follow specified repair and maintenance procedures.
• Do not wear rings, wristwatches, jewellery, unbuttoned or loose articles of clothing such as: ties, torn clothing,
scarves, open jackets or shirts with open zips that may remain entangled in moving parts.
It is advised to wear approved safety clothing, e.g: non--slip footwear, gloves, safety goggles, helmets, etc.
• Do not carry out repair operations with someone sitting in the driver’s seat, unless the person is a trained technician
who is assisting with the operation in question.
• Operate the vehicle and use the implements exclusively from the driver’s seat.
• Do not carry out operations on the vehicle with the engine running, unless specifically indicated.
• Stop the engine and ensure that all pressure is relieved from hydraulic circuits before removing caps, covers, valves,
etc.
• All repair and maintenance operations must be carried out using extreme care and attention.
• Service steps and platforms used in a workshop or in the field should be built in compliance with the safety rules in
force.
• Disconnect the batteries and label all controls to indicate that the vehicle is being serviced. Block the machine and
all equipment which should be raised.
• Do not check or fill fuel tanks, accumulator batteries, nor use starting liquid when smoking or near naked flames,
as these fluids are inflammable.
• Brakes are inoperative if manually released for repair or maintenance purposes.
In such cases, the machine should be kept constantly under control using blocks or similar devices.
• The fuel nozzle should always be in contact with the filling aperture. Maintain this position until filling operations
are completed in order to avoid possible sparks caused by the accumulation of static electricity.
• Only use specified towing points for towing the tractor, connect parts carefully.Make sure that all pins and/or locks
are secured in position before applying traction.
Never remain near the towing bars, cables or chains that are operating under load
• Transport vehicles that cannot be driven using a trailer or a low--loading platform trolley, if available.
• When loading or unloading the vehicle from the trailer (or other means of transport), select a flat area capable
of sustaining the trailer or truck wheels, firmly secure the tractor to the truck or trailer and lock the wheels in the
position.
• Electric heaters, battery--chargers and similar equipment must only be powered by auxiliary power supplies with
efficient ground insulation to avoid electrical shock hazards.
• Always use suitable hoisting or lifting devices when raising or moving heavy parts.
• Take extra care if bystanders are present.
• Never pour gasoline or diesel oil into open, wide and low containers.
• Never use gasoline, diesel oil or other inflammable liquids as cleaning agents. Use non-flammable non-toxic pro-
prietary solvents.
• Wear safety goggles with side guards when cleaning parts with compressed air.
• Limit the air pressure to a maximum of 2.1 bar (30.5 psi), according to local regulations.
47888397 08/07/2016
5

INTRODUCTION
• Do not run the engine in confined spaces without suitable ventilation.
• Do not smoke, use naked flames, or cause sparks in the area when fuel filling or handling highly inflammable liquids.
• Never use naked flames for lighting when working on the machine or checking for leaks.
• All movements must be carried out carefully when working under, on or near the vehicle and wear protective equip-
ment: helmets, goggles and special footwear.
• When carrying out checks with the engine running, request the assistance of an operator in the driver’s seat. The
operator must maintain visual contact with the service technician at all times.
• If operating outside the workshop, position the vehicle on a flat surface and lock in position. If working on a slope,
lock the vehicle in position and move to a flat area as soon as is safely possible.
• Damaged or bent chains or cables are unreliable. Do not use them for lifting or towing.
Always use suitable protective gloves when handling chains or cables.
• Chains should always be safely secured. Ensure that fastening device is strong enough to hold the load foreseen.
No persons should stop near the fastening point, trailing chains or cables.
• Maintenance and repair operations must be carried out in a CLEAN and DRY area, eliminate any water or oil spillage
immediately.
• Do not create piles of oil or grease--soaked rags as they represent a serious fire hazard; store them in a closed
metal container.
Before starting the vehicle or implements, make sure that the driver’s seat is locked in position and always check
that the area is free of persons or obstacles.
• Empty pockets of all objects that may fall unobserved into the vehicle parts when disassembled.
• In the presence of protruding metal parts, use protective goggles or goggles with side guards, helmets, special
footwear and gloves.
• Handle all parts carefully, do not put your hands or fingers between moving parts, wear suitable safety clothing --
safety goggles, gloves and shoes.
WELDING OPERATIONS
• When welding, use protective safety devices: tinted safety goggles, helmets, special overalls, gloves and footwear.
All persons present in the area where welding is taking place must wear tinted goggles.
NEVER LOOK AT THE WELDING ARC IF YOUR EYES ARE NOT SUITABLY PROTECTED.
• Where possible, remove the part or tool that requires arc welding from the tractor.
• Disconnect both battery leads. Isolate the cable ends to avoid contact with each other and the tractor.
• Position the welder ground clamp as near as possible to the area where welding is taking place.
• Remove the electronic control units located on the tractor if welding is to be carried out near these control units.
• Never allow welding cables to lay on, near or across any electrical wiring or electronic component while welding is
in progress.
• Metal cables tend to fray with repeated use. Always use suitable protective devices (gloves, goggles, etc.) when
handling cables.
START UP
• Never start the engine in confined spaces that are not equipped with adequate ventilation for exhaust gas extraction.
• Never place the head, body, limbs, feet, hands or fingers near fans or rotating belts.
ENGINE
• Always loosen the radiator cap slowly before removing it to allow any remaining pressure in the system to be dis-
charged. Coolant should be topped up only when the engine is stopped or idle if hot.
• Never fill up with fuel when the engine is running, especially if hot, in order to prevent the outbreak of fire as a result
of fuel spillage
• Never check or adjust fan belt tension when the engine is running.
Never adjust the fuel injection pump when the vehicle is moving.
47888397 08/07/2016
6

INTRODUCTION
• Never lubricate the vehicle when the engine is running.
ELECTRICAL SYSTEMS
• If it is necessary to use auxiliary batteries, remember that both ends of the cables must be connected as follows:
(+) with (+) and (-) with (-).
• Avoid short-circuiting the terminals. GAS RELEASED FROM BATTERIES IS HIGHLY INFLAMMABLE.
• During charging, leave the battery compartment uncovered to improve ventilation.
• Never check the battery charge using ”jumpers” (metal objects placed on the terminals).
• Avoid sparks or flames near the battery zone to prevent explosion hazards.
• Before servicing operations, check for fuel or current leaks. Eliminate any eventual leaks before starting work.
• Never charge batteries in confined spaces. Make sure that there is adequate ventilation in order to prevent acci-
dental explosion hazards as a result of the accumulation of gases released during charging operations.
• Always disconnect the battery before performing any kind of servicing on the electrical system.
HYDRAULIC SYSTEMS
• Some fluid slowly coming out from a very small port can be almost invisible and be strong enough to penetrate the
skin. Check for leaks using a piece of cardboard, NEVER USE HANDS.
• If any liquid penetrates skin tissue, call for medical aid immediately
• Serious skin infections may result if medical attention is not given.
• Use the specific tools when checking pressure values on the hydraulic system.
WHEELS AND TYRES
• Check that the tyres are correctly inflated at the pressure specified by the manufacturer.
Periodically check possible damages to the rims and tyres.
• Stand away from (at the side of) the tire when checking inflation pressure.
• Only check pressure when the vehicle is unloaded and the tires are cold, to avoid incorrect readings as a result of
over--pressure.
• Do not re--use parts of recovered wheels as incorrect welding or brazing may heat the material, causing it to weaken
and eventually damage or break the wheel.
• Never cut, nor weld a rim with the inflated tyre assembled.
• When removing the wheels, lock both the front and rear vehicle wheels.
• Always position support stands when raising the vehicle, in order to conform to current safety regulations.
• Deflate the tyre before removing any object caught into the tyre tread.
• Never inflate tires using inflammable gases; this could cause an explosion and put operator safety at risk.
REMOVAL AND RE-FITTING
• Lift and handle all heavy parts using suitable lifting equipment and make sure that all slings and hooks are correctly
secured.
• Handle all parts carefully during lifting operations, keep an eye on the personnel working near the load to be lifted.
Never insert hands or fingers between parts, always wear approved accident prevention clothing (goggles, gloves
and work boots).
• Avoid twisting chains or metal cables and always wear safety gloves when handling cables or chains.
47888397 08/07/2016
7

SERVICE MANUAL
Engine
Farmall® 105N With cab [ZBJF20417 - ], Farmall® 105N Without cab
[ZCJF16900 - ], Farmall® 105V With Cab [ZBJF20562 - ], Farmall® 105V
Without cab [ZDJF09419 - ], Farmall® 75N With cab - Model Year 2012
75N Without cab [Z9JF01865 - ZCJF07697], Farmall® 75N Without cab -
Model Year 2012 [ZCJF07813 - ], Farmall® 85N With cab - Model Year 2012
cab [Z9JF01936 - ZCJF10868], Farmall® 95N With cab - Model Year 2012
cab [Z9JF01090 - ZCJF05141]
47888397 08/07/2016
10

Engine - Engine and crankcase
Engine - Remove
1. Remove the cab as described in operation " Cab - Re-
move (90.150)”.
2. Extract the fixing pin and remove the ballast (1) ; un-
screw the retaining screws and retrieve the ballast sup-
port (2) .
WLSPVNS10C1-10A 1
3. Carry out operation in: Drive shaft - Disassemble
(21.145), propeller shafts and guard, only removal.
4. Unscrew the plug and drain the front transmission cas-
ing (prescribed quantity: 44 l (11.62 US gal)).
WLSPVNS10C1-11A 2
5. Disconnect the pipes ( (1) and (2) ) of the transmission
oil cooler and of the front axle differential lock.
WLSPVNS10C1-12A 3
6. Disconnect: the transmission oil cooler pipes (1) and
the front axle differential lock pipe (2) .
WLSPVNS10C1-13A 4
47888397 08/07/2016
10.1 [10.001] / 3

7. Unscrew: the retaining bolts of the pipe (1) delivering
oil to the pump and the bolts retaining the pipe (2) to
the filter support.
WLSPVNS10C1-14A 5
8. Loosen the related clamps and remove the sleeve (2)
from the pipe (1) and remove the transmission oil inlet
pipe together with the above-mentioned sleeve.
WLSPVNS10C1-15A 6
9. Unscrew the fixing clamps and disconnect the pipes (
(1) and (2) ) from the cooler, the sleeve (4) between
the air filter and the turbocharger and the oil vapour
recirculation pipe (3) .
WLSPVNS10C1-16A 7
10. Disconnect the secondary tank fuel level connection
(1) and the clogged air filter pressure switch connec-
tion.
WLSPVNS10C1-17A 8
47888397 08/07/2016
10.1 [10.001] / 4

11. Disconnect the steering hydraulic cylinder control
pipes (1) .
WLSPVNS10C1-18A 9
12. Unscrew the fixing clamps and detach the upper (1)
and lower (2) sleeves from the engine radiator.
WLSPVNS10C1-19A 10
13. Unhook the catch and extract the transmission oil ra-
diator (1) .
WLSPVNS10C1-20A 11
14. Disconnect the pipes (1) of the air-conditioning system
from the related condenser.
WLSPVNS10C1-21A 12
47888397 08/07/2016
10.1 [10.001] / 5

15. Unscrew the fixing screws, loosen the related clamp
and detach the pipe (1) joining the tanks: main to sec-
ondary.
WLSPVNS10C1-22A 13
16. Unscrew the fixing screw and detach the bracket (1)
locking the engine radiator.
WLSPVNS10C1-23A 14
17. Position a fixed stand under the transmission− clutch
casing.
18. Connect the engine to the hoist using a chain and
make it take up the strain.
19. Unscrew the bolts (1) securing the engine to the trans-
mission-clutch casing and detach the engine assem-
bly and front axle.
WLSPVNS10C1-24A 15
20. Set up two fixed stands: one under the axle support
at the rear and the other under the front side.
21. Unscrew the bolts (1) on both sides and separate the
engine from the axle-support assembly with the radi-
ators.
22. Rest the engine on an adequate support.
WLSPVNS10C1-26A 16
47888397 08/07/2016
10.1 [10.001] / 6

Engine - Install
1. Respect the tightening torques.
2. Connect the engine, with chains, to the hoist.
3. Refit the engine to the front axle-support assembly with
the radiator and cooler.
4. Before refitting the engine to the clutch box carefully
clean the mating surfaces and apply sealing compound
( 2 mm (0.08 in) diameter), according to the diagram
shown in Transmission housing - Reseal (21.114) .
5. Position the engine on the clutch casing and secure it
with the specific bolts.
6. Position and secure the retaining bracket between the
radiator and engine.
7. Secure the pipe joining the main tank to the secondary
one.
8. Position and secure the guard between the radiator and
engine.
9. Connect the air-conditioning system pipes to the con-
denser.
10. Insert the transmission oil radiator into its seat and
secure it.
11. Connect and secure the top and bottom sleeves to the
engine radiator.
12. Connect the steering cylinder control piping.
13. Connect the electrical connections of the secondary
tank fuel level and clogged air filter.
14. Position and secure the connecting pipes of the
cooler, turbocharger, air filter and oil vapour recircu-
lation.
15. Position and connect the transmission oil inlet pipe.
16. Position and secure the pipes of the transmission oil
filter support.
17. Connect the transmission oil cooler and front axle dif-
ferential lock pipes.
18. Carry out operation Drive shaft - Assemble (21.145)
Propeller shafts and guard, only installation
19. Connect the cooler and front axle differential lock
pipes.
20. For models fitted with brakes on the front axle it is nec-
essary to fill the relevant tank (see dedicated section
for the prescribed product and quantity) and bleed the
braking system.
21. Screw the plug on the rear transmission casing and fill
up with oil (see dedicated section for the prescribed
product and quantity).
22. Position and secure the ballast support.
23. Position and secure the ballast.
24. Install the cab as described in operation Cab - Install
(90.150).
47888397 08/07/2016
10.1 [10.001] / 7

Clutch - Clutch mechanical release control
Clutch mechanical release control - Remove
Prior operation:
A. Disconnect the battery negative prong.
B. Remove the front left-hand panel.
1. Partially disconnect the fuse holder box (1) and the di-
agnosis socket (2).
MOIL16TR01988AA 1
2. Correctly disconnect the electrical connector (1) from
the engine starting inhibitor switch (2).
3. Loosen the two indicated connection screws of the
switch (2) and the relevant washers.
4. Store the switch (2) in a suitable location.
MOIL16TR01989AA 2
5. Disconnect the retaining clip (1) of the clutch (3) control
lever cable (2) under the dashboard on the right-hand
side of the vehicle.
MOIL16TR01344AA 3
47888397 08/07/2016
18.1 [18.100] / 3

6. Unscrew the four nuts (1) on the master clutch pedal.
MOIL16TR00373AA 4
7. Unscrew the nut (1) and release the upper side of the
spring (2).
8. Remove the lower side of the spring from the small rod
(3).
MOIL16TR00374AA 5
9. Manually remove the spring (1) including eyelet screw
(2) and store them in a suitable place.
MOIL16TR00375AA 6
10. Loosen the screw (1).
11. Move down the tie rod (2).
12. Manually extract the pedal axle rod (5) and store it in
a suitable place.
13. Manually remove the master clutch pedal (4) including
the tie rod (2) from the pedal holder (3).
MOIL16TR00376AA 7
47888397 08/07/2016
18.1 [18.100] / 4

14. Remove the seeger (3) and release the tie rod pin (1).
15. Remove the tie rod (2) and store it in a suitable place.
16. Remove the two indicated needle bearings from the
clutch pedal axle.
MOIL16TR00378AA 8
47888397 08/07/2016
18.1 [18.100] / 5

Clutch mechanical release control - Install
1. Recover and thoroughly clean the master clutch pedal
(1) and the tie rod (2).
MOIL16TR00379AA 1
2. Install the tie rod pin (1).
3. Install the tie rod (2) and fasten the seeger (3).
4. Install the two indicated needle bearings inside the
clutch pedal axle.
MOIL16TR00378AA 2
5. Recover and thoroughly clean the pedal axle rod (1).
MOIL16TR00377AA 3
6. Recover and thoroughly clean the master clutch pedal
holder.
7. Correctly place the master clutch pedal axle (4) on the
holder (3).
8. Move down the tie rod (2).
9. Correctly insert the rod (5) inside the pedal axle (4).
10. Fasten the screw (1).
MOIL16TR00376AA 4
47888397 08/07/2016
18.1 [18.100] / 6

11. Recover and thoroughly clean the spring (1) including
the eyelet screw (2).
MOIL16TR00375AA 5
12. Clip the lower side of spring on the small rod (3).
13. Correctly place the eyelet screw (2) of the upper side
of the spring.
14. Fasten the nut (1).
MOIL16TR00374AA 6
15. Thoroughly clean the master clutch pedal assembly
housing under the dashboard column on the left side
of the vehicle.
16. Carefully place the master clutch pedal assembly on
its housing.
17. Fasten the four indicated nuts (1).
MOIL16TR00373AA 7
18. Correctly place and fasten the clip (1) of the cable (2)
on the master clutch pedal (3) under the dashboard
column on the left side of the vehicle.
MOIL16TR01344AA 8
47888397 08/07/2016
18.1 [18.100] / 7

19. Recover and thoroughly clean the engine starting in-
hibitor switch (1).
20. Correctly connect the electrical connector (2) to the
switch (1).
21. Tighten the two indicated connection screws and the
relevant washers.
MOIL16TR01989AA 9
Next operation:
A. Connect the battery negative prong.
B. Proceed to the clutch pedal calibration through the menu HH.
C. Reconnect the front left-hand panel.
47888397 08/07/2016
18.1 [18.100] / 8

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Clutch - Clutch hydraulic release control
Clutch hydraulic release control - Travel adjust
1. If the position of the clutch pedal (1) requires adjust-
ment, or after a clutch overhaul, check that main clutch
pedal travel (A) is between 148 - 152 mm (5.8268 -
5.9842 in). If not, adjust as follows:
WLSPVNS18C1-48A 1
• Loosen the locknut (1) and turn the nut (2) anticlock-
wise.
• Check that travel is between 148 - 152 mm (5.8268
- 5.9842 in).
• Tighten the locknut (1).
WLSPVNS18C1-49A 2
• Operate the unit four or five times.
• Check that the clutch pedal (1) travel is as pre-
scribed.
• If necessary, reset to the correct value (A), as previ-
ously described.
• After having correctly adjusted pedal travel, check
that the entire distance is travelled with a maximum
load of 190 N·m (140.14 lb ft).
WLSPVNS18C1-50A 3
47888397 08/07/2016
18.2 [18.104] / 3

Clutch - Clutch and components
Clutch - Remove
1. Carry out operation cab with platform unit, only removal
(see Cab and platform - Remove (90.150)) (models
with cab).
NOTE: Make sure that the bracket 380001613 locking the
front axle in relation to the engine is positioned and secured
between them.
2. Carry out operation, platform assembly, only removal
(see Cab and platform - Remove (90.150)) (models
with platform).
3. Remove the front roll bar.
4. Unscrew the plug and drain the front transmission cas-
ing (prescribed quantity: 44 l (11.62 US gal)).
WLSPVNS18C1-05A 1
5. Loosen the hydraulic pump line piping bolts (1).
WLSPVNS18C1-06A 2
6. Loosen the clamps (1), (3) and (4), unscrew the bracket
retaining bolts (2) and remove the hydraulic pump line
piping (5).
WLSPVNS18C1-07A 3
47888397 08/07/2016
18.3 [18.110] / 8

7. Unscrew the filter piping (1) and (2).
8. Unscrew the services distributor piping (3), (4) and (5).
WLSPVNS18C1-08A 4
9. Disconnect and remove piping (1), (2), (3), (4), (5) and
(6).
10. Carry out operation exhaust pipe, only removal (see
engine).
WLSPVNS18C1-09A 5
11. Disconnect the piping (2), unscrew the clamp (1), the
piping/clutch housing retaining bolt, and remove pip-
ing (1) and (3).
WLSPVNS18C1-10A 6
12. Remove the starter motor guard and disconnect the
wire (1).
13. Remove the retaining clamps and disconnect the elec-
trical wires from the engine.
14. Disconnect the piping (2).
WLSPVNS18C1-11A 7
47888397 08/07/2016
18.3 [18.110] / 9

15. Disconnect the brake piping (1) from the block.
16. Carry out operation, propeller shafts and guard, only
removal (see Drive shaft - Disassemble (21.145)).
WLSPVNS18C1-12A 8
17. Using a chain, connect the engine to a hoist and po-
sition a fixed stand under the clutch casing.
18. Unscrew the bolt (2) accessing the allen screw (1) (on
both sides).
WLSPVNS18C1-13A 9
19. Unscrew all of the clutch casing − engine bolts and
detach the engine.
WLSPVNS18C1-14A 10
20. Using tool 380001760 (2), unscrew the retaining bolts
and remove the clutch (1) (models fitted with Power
Shuttle).
WLSPVNS18C1-15A 11
47888397 08/07/2016
18.3 [18.110] / 10

21. Using tool 380001760 (1), unscrew the retaining bolts
and remove the clutch (2) (models fitted with mechan-
ical gearbox).
WLSPVNS18C1-17A 12
47888397 08/07/2016
18.3 [18.110] / 11

Case ih farmall 85 n with cab tier 3 tractor service repair manual pin z8jf17086 zcjf09425

More Related Content

Similar to Case ih farmall 85 n with cab tier 3 tractor service repair manual pin z8jf17086 zcjf09425 (9)

More from fjjskksekmemm (20)

Recently uploaded (20)

Case ih farmall 85 n with cab tier 3 tractor service repair manual pin z8jf17086 zcjf09425