CASE IH Magnum 290 Powershift Transmission (PST) Tractor Service Repair Manual (PIN ZCRD02585 and above).pdf

Printed in U.S.A.
Copyright © 2013 CNH America LLC. All Rights Reserved.
Case IH is a registered trademark of CNH America LLC.
Racine Wisconsin 53404 U.S.A.
Magnum 235
Magnum 260
Magnum 290
Magnum 315
Magnum 340
Powershift Transmission (PST)
Tractor
PIN ZCRD02585 and above
Part number 47533563
1st
edition English
April 2013
SERVICE MANUAL

Contents
INTRODUCTION
Engine....................................................................................... 10
[10.001] Engine and crankcase ............................................................. 10.1
[10.101] Cylinder heads ..................................................................... 10.2
[10.114] Pump drives ........................................................................ 10.3
[10.202] Air cleaners and lines .............................................................. 10.4
[10.216] Fuel tanks .......................................................................... 10.5
[10.310] Aftercooler.......................................................................... 10.6
[10.400] Engine cooling system ............................................................. 10.7
[10.414] Fan and drive ...................................................................... 10.8
[10.500] Selective Catalytic Reduction (SCR) exhaust treatment ........................... 10.9
Power coupling........................................................................... 19
[19.100] Drive shaft.......................................................................... 19.1
Transmission.............................................................................. 21
[21.105] Powershift transmission lubrication system ........................................ 21.1
[21.113] Powershift transmission ............................................................ 21.2
[21.135] Powershift transmission external controls.......................................... 21.3
[21.155] Powershift transmission internal components...................................... 21.4
[21.200] Dropbox ............................................................................ 21.5
Four-Wheel Drive (4WD) system .................................................. 23
[23.202] Electro-hydraulic control ........................................................... 23.1
[23.314] Drive shaft.......................................................................... 23.2
Front axle system ....................................................................... 25
[25.100] Powered front axle ................................................................. 25.1
[25.102] Front bevel gear set and differential ............................................... 25.2
[25.108] Final drive hub, steering knuckles, and shafts ..................................... 25.3
47533563 18/04/2013

[25.122] Axle suspension control............................................................ 25.4
Rear axle system........................................................................ 27
[27.100] Powered rear axle.................................................................. 27.1
[27.106] Rear bevel gear set and differential................................................ 27.2
[27.120] Planetary and final drives .......................................................... 27.3
Power Take-Off (PTO)................................................................. 31
[31.110] One-speed rear Power Take-Off (PTO) ............................................ 31.1
[31.114] Two-speed rear Power Take-Off (PTO) ............................................ 31.2
[31.146] Front Power Take-Off (PTO) ....................................................... 31.3
Brakes and controls .................................................................... 33
[33.110] Parking brake or parking lock ...................................................... 33.1
[33.202] Hydraulic service brakes ........................................................... 33.2
[33.220] Trailer brake hydraulic control...................................................... 33.3
[33.224] Trailer brake pneumatic control .................................................... 33.4
Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.102] Pump control valves................................................................ 35.2
[35.106] Variable displacement pump ....................................................... 35.3
[35.114] Three-point hitch control valve ..................................................... 35.4
[35.124] Three-point hitch hydraulic adjustment ............................................ 35.5
[35.204] Remote control valves ............................................................. 35.6
[35.300] Reservoir, cooler, and filters........................................................ 35.7
[35.304] Combination pump units ........................................................... 35.8
Pneumatic system ...................................................................... 36
[36.100] Pneumatic system.................................................................. 36.1
Hitches, drawbars, and implement couplings.................................. 37
[37.110] Rear three-point hitch .............................................................. 37.1
[37.162] Front hitch.......................................................................... 37.2
47533563 18/04/2013

Steering..................................................................................... 41
[41.101] Steering control .................................................................... 41.1
[41.200] Hydraulic control components...................................................... 41.2
[41.206] Pump ............................................................................... 41.3
Cab climate control ..................................................................... 50
[50.100] Heating ............................................................................. 50.1
[50.200] Air conditioning..................................................................... 50.2
[50.300] Cab pressurizing system ........................................................... 50.3
Electrical systems....................................................................... 55
[55.012] Engine cooling system ............................................................. 55.1
[55.015] Engine control system.............................................................. 55.2
[55.024] Transmission control system....................................................... 55.3
[55.045] Front axle control system .......................................................... 55.4
[55.046] Rear axle control system........................................................... 55.5
[55.050] Heating, Ventilation, and Air-Conditioning (HVAC) control system................. 55.6
[55.051] Cab Heating, Ventilation, and Air-Conditioning (HVAC) controls................... 55.7
[55.100] Harnesses and connectors......................................................... 55.8
[55.130] Rear three-point hitch electronic control system ................................... 55.9
[55.201] Engine starting system ........................................................... 55.10
[55.301] Alternator......................................................................... 55.11
[55.302] Battery............................................................................ 55.12
[55.404] External lighting .................................................................. 55.13
[55.405] External lighting switches and relays ............................................ 55.14
[55.408] Warning indicators, alarms, and instruments .................................... 55.15
[55.512] Cab controls...................................................................... 55.16
[55.514] Cab lighting ...................................................................... 55.17
[55.518] Wiper and washer system........................................................ 55.18
[55.640] Electronic modules ............................................................... 55.19
[55.988] Selective Catalytic Reduction (SCR) electrical system .......................... 55.20
47533563 18/04/2013

[55.DTC] FAULT CODES.................................................................. 55.21
Platform, cab, bodywork, and decals............................................. 90
[90.100] Engine hood and panels ........................................................... 90.1
[90.102] Engine shields, hood latches, and trims ........................................... 90.2
[90.118] Protections and footboards......................................................... 90.3
[90.124] Pneumatically-adjusted operator seat.............................................. 90.4
[90.150] Cab................................................................................. 90.5
[90.151] Cab interior......................................................................... 90.6
[90.160] Cab interior trim and panels........................................................ 90.7
47533563 18/04/2013

INTRODUCTION
47533563 18/04/2013
1

INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual and on machine decals, you will find the signal words DANGER, WARNING, and CAUTION
followed by special instructions. These precautions are intended for the personal safety of you and those working
with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. The
color associated with DANGER is RED.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
The color associated with WARNING is ORANGE.
CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result
in minor or moderate injury. The color associated with CAUTION is YELLOW.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation which, if not avoided, could result in machine or property damage. The color
associated with Notice is BLUE.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information which clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
47533563 18/04/2013
3

INTRODUCTION
Safety rules
Magnum 235, Magnum 260, Magnum 290, Magnum 315, Magnum 340
Standard safety precautions
Be informed and notify personnel of the laws in force regulating safety, and provide documentation available for
consultation.
• Keep working areas as clean as possible.
• Ensure that working areas are provided with emergency boxes. They must be clearly visible and always contain
adequate sanitary equipment.
• Fire extinguishers must be properly identified and always be clear of obstructions. Their efficiency must be checked
on a regular basis and personnel must be trained on proper interventions and priorities.
• Keep all emergency exits free of obstructions and clearly marked.
• Smoking in working areas subject to fire danger must be strictly prohibited.
Prevention of injury
• Wear suitable work attire and safety glasses with no jewelry such as rings and chains when working close to engines
and equipment in motion.
• Wear safety gloves and goggles when performing the following operations:
• Topping off or changing lubrication oils.
• Using compressed air or liquids at a pressure greater than 2 bar (29 psi).
• Wear a safety helmet when working close to hanging loads or equipment working at head level.
• Always wear safety shoes and fitting clothes.
• Use protection cream for hands.
• Change wet clothes as soon as possible.
• In the presence of voltages exceeding 48 - 60 V, verify the efficiency of the ground and mass electrical connections.
Ensure that hands and feet are dry and use isolating foot boards. Workers should be properly trained to work with
electricity.
• Do not smoke or start an open flame close to batteries and any fuel material.
• Place soiled rags with oil, diesel fuel or solvents in specially provided anti-fire containers.
• Do not use any tool or equipment for any use other than what it was originally intended for. Serious injury may
occur.
• If running an engine indoors, make sure there is a sufficient exhaust fan in use to eliminate exhaust fumes.
During maintenance
• Never open the filler cap of the cooling system when the engine is hot. High temperature liquid at operating pressure
could result in serious danger and risk of burn. Wait until the temperature decreases under 50 °C (122 °F).
• Never add coolant to an overheated engine and use only appropriate liquids.
• Always work when the engine is turned off. Certain circumstances require maintenance on a running engine. Be
aware of all the risks involved with such an operation.
• Always use adequate and safe containers for engine fluids and used oil.
• Keep engine clean of any spilled fluids such as oil, diesel fuel, and or chemical solvents.
• Use of solvents or detergents during maintenance may emit toxic vapors. Always keep working areas aerated.
Wear a safety mask if necessary.
• Do not leave soiled rags that may contain any flammable substances close to the engine.
• Always use caution when starting an engine after any work has been performed. Be prepared to cut off intake air
in case of engine runaway.
• Never disconnect the batteries while the engine is running.
47533563 18/04/2013
4

INTRODUCTION
• Disconnect the batteries prior to performing any work on the equipment.
• Disconnect the batteries to place a load on them with a load tester.
• After any work is performed, verify that the battery clamp polarity is correct and that the clamps are tight and safe
from accidental short circuit and oxidation.
• Before disconnecting any pipelines (pneumatic, hydraulic, fuel pipes, etc.), verify that all pressure has been re-
leased. Take all necessary precautions bleeding and draining residual pressure. Always wear the proper safety
equipment.
• Do not alter the lengths of any wires.
• Do not connect any electronic service tool to the engine electrical equipment unless specifically approved by Iveco.
• Do not modify the fuel system or hydraulic system unless approved by Iveco, Any unauthorized modification will
compromise warranty assistance and may affect engine operation and life span.
For engine equipped with an electronic control unit
• Do not weld on any part of the equipment without removing the control unit.
• Remove the in case of work requiring heating over 80 °C (176 °F).
• Do not paint the components and the electronic connections.
• Do not alter any data filed in the electronic control unit driving the engine. Any manipulation or alteration of electronic
components will void engine warranty assistance and may affect the correct working order and life span of the
engine.
Respect of the Environment
• Respect of the environment should be of primary importance. Take all necessary precautions to ensure personnel's
safety and health.
• Inform the personnel of the laws regarding the dispensing of used engine fluids.
• Handle batteries with care, storing them in a well ventilated environment and within anti-acid container.
47533563 18/04/2013
5

SERVICE MANUAL
Engine
Magnum 235 NA
Magnum 260 NA
Magnum 290 NA
Magnum 315 NA
Magnum 340 NA
47533563 18/04/2013
10

Engine - Engine and crankcase
Engine - Remove
Prior operation:
Battery - Disconnect (55.302)
Prior operation:
Side shield - Remove (90.102)
Prior operation:
Hood - Remove (90.100)
Prior operation:
Engine cooling system - Emptying (10.400)
Prior operation:
Air conditioning - Recover (50.200)
NOTE: During the disassembly of components with O-ring seals, the seals should be discarded and new seal installed
during assembly.
NOTE: Cap all fittings and plug all lines/hoses as they are disconnected.
1. Disconnect the hydraulic cooling line connection on
the right side (from oil cooler).
NOTE: Be prepared to collect some hydraulic oil by placing
a pan under the fitting.
RCPH10CCH771AAB 1
2. Disconnect the hydraulic line (1) on the left side (to
oil cooler). Disconnect the engine cooling fan drive
harness connector (3)
3. Disconnect the air conditioning low pressure hose to
line fitting (return from condenser) (2).
4. Remove the bolt securing the harness P-clamp (4).
RCPH10CCH772AAB 2
5. Disconnect the air conditioning high pressure hose
to tube fitting (1).
6. Disengage the hose clamps (2), and disconnect the
cooler hoses (3) (4).
RCPH10CCH773AAB 3
47533563 18/04/2013
10.1 [10.001] / 3

7. Disengage the hose clamps (1) and disconnect the
air vent hose (2) and the hose (3) from the deaeration
tank to the recovery bottle.
RCPH10CCH774AAB 4
8. Loosen the turbocharger clamp (1).
9. Loosen the air cooler inlet hose clamp (2).
10. Remove the pipe (3) and set aside.
11. Repeat for the right side air to air tube from the cooler
to the intake manifold (not shown).
RCPH10CCH775AAB 5
12. Remove and discard the O-ring seal from the elbow.
RCPH10CCH778AAB 6
13. Remove and discard the O-ring seal from the elbow.
RCPH10CCH777AAB 7
47533563 18/04/2013
10.1 [10.001] / 4

14. Loosen the hose clamp (1) at the engine coolant
outlet and disconnect the hose from the thermostat
housing.
RCPH10CCH776AAB 8
15. Loosen the hose clamp and disconnect the coolant
line into the engine hose.
RCPH10CCH580AAB 9
16. Remove the nuts (1) and disengage the engine
heater grid cables (2) (3) to the fuse block.
17. Disconnect the harness connector (4) for the 12 V
auxiliary power connection .
RCPH10CCH779AAB 10
18. Disconnect the ECM (engine control module) con-
nector (1) by moving the locking handle (2) from the
right (locked position) to the left (unlocked position).
RCPH10CCH780AAB 11
47533563 18/04/2013
10.1 [10.001] / 5

19. Disconnect the tractor to engine harness connectors
(1).
RCPH10CCH781AAB 12
20. Disconnect the harness connectors to the alternator
(1) and the A/C compressor clutch (2).
21. Remove the upper left A/C compressor bolt and re-
move the ground wire (3).
RCPH10CCH782AAB 13
22. Disconnect the harness connectors to the A/C high
pressure switch (1) and the engine cooling fan drive
(2).
RCPH10CCH783AAB 14
23. Disconnect the harness connector (1) to the grid
heater controller.
RCPH10CCH784AAB 15
47533563 18/04/2013
10.1 [10.001] / 6

24. Remove the nut (1) and the clamp bolts (2). Disen-
gage the power cable (3).
RCPH10CCH785AAB 16
25. Loosen the nut (1) and disconnect the fuel supply line
to the EMC cooler
RCPH10CCH787AAB 17
26. Disengage the clamp (1) and disconnect the fuel re-
turn hose (2) from the pipe.
RCPH10CCH786AAB 18
27. Remove the nut (1) and disengage the alternator out-
put cable (2).
RCPH10CCH788AAB 19
47533563 18/04/2013
10.1 [10.001] / 7

28. Loosen the nuts (1) and disconnect the compressor
inlet (2) and outlet (3) tubes.
RCPH10CCH789AAB 20
29. Disconnect the harness connector to the SCR heater
control valve solenoid (1).
30. Raise the locking wire (2) and disconnect the heater
supply connector (3) from the valve.
31. Repeat for the outlet hose connection (located on the
right side of the valve).
RCPH10CCH790AAB 21
32. Disconnect the main engine to chassis harness con-
nector.
RCPH10CCH791AAB 22
33. Disconnect the auxiliary engine to chassis harness
connectors (1).
RCPH10CCH792AAB 23
47533563 18/04/2013
10.1 [10.001] / 8

34. Remove the holding nut (1) and disengage the
ground wire (2).
RCPH10CCH793AAB 24
35. Loosen the fitting and disconnect the hydraulic oil line
(1) (right side of engine).
RCPH10CCH798AAB 25
36. Disconnect the water in fuel sensor connector (1)
from the primary fuel filter.
RCPH10CCH794AAB 26
37. Loosen the nuts (1) and disconnect the A/C lines lo-
cated between the hood support and the cab.
RCPH10CCH799AAB 27
47533563 18/04/2013
10.1 [10.001] / 9

38. Remove the jump start stud.
RCPH10CCH796AAB 28
39. Remove the nut (1) and disengage the cables from
the starter.
RCPH10CCH797AAB 29
40. Remove the plug (1), remove the attaching screw (2)
and remove the starter solenoid wire (3).
RCPH10CCH818AAB 30
41. Loosen the hose clamp (1) and disconnect the fill
hose elbow (2).
RCPH10CCH795AAB 31
47533563 18/04/2013
10.1 [10.001] / 10

42. Remove the six socket head bolts (1) and three back-
ing plates (2) securing the drive shaft assembly to
the engine drive pulley. Disengage the drive from
the pulley.
RCPH10CCH562AAB 32
43. Remove the nuts and washers (1) from the cooling
assembly support bracket on the left and right sides.
RCPH10CCH572AAB 33
44. Properly support the bracket, and remove the four
bolts (1) securing the bracket to the hood support.
Remove the assembly and set aside.
RCPH10CCH037BAB 34
45. Loosen the clamp (1) and disconnect the coolant fill
line.
46. Loosen the nuts (2) and (3) and disconnect the cab
heater supply and return lines.
47. Disengage the clamp (4) and remove the air bleed
hose.
48. Remove the three bolts (5) securing the front support
bracket.
RCPH10CCH038BAB 35
47533563 18/04/2013
10.1 [10.001] / 11

49. Remove the two bolts (1) securing the rear support
bracket.
RCPH10CCH800AAB 36
50. Disconnect the harness connector (1) to the dosing
valve.
RCPH10CCH801AAB 37
51. Disconnect the DEF supply and return hoses (1).
NOTE: Squeeze the locking tabs (2) together and pull
straight upward on the elbow.
RCPH10CCH359AAB 38
52. Remove the clamp (1) at the turbocharger. Repeat
for clamp at the other end of the pipe (2). Remove
the pipe and set aside.
RCPH10CCH806AAB 39
47533563 18/04/2013
10.1 [10.001] / 12

53. Remove the clamp (1) at the SCR muffler. Remove
the attaching bolt (2) securing the support bracket.
Remove the pipe and set aside.
RCPH10CCH803AAB 40
54. Disengage the engine blow-by hose clamp (1) at the
intake pipe. Disconnect from the intake pipe.
RCPH10CCH805AAB 41
55. Disengage the engine blow-by hose clamp (1) at the
engine. Remove the pipe and set aside.
RCPH10CCH807AAB 42
56. Loosen the clamp (1) securing the intake pipe elbow
to the turbocharger. Disconnect from the turbo.
RCPH10CCH809AAB 43
47533563 18/04/2013
10.1 [10.001] / 13

57. Remove the two bolts (1) securing the support clamp
to the intake pipe.
RCPH10CCH808AAB 44
58. Remove the bolt (1) securing the intake support
clamp to the bracket. Loosen the clamp (2). Re-
move the upper intake pipe and set aside.
RCPH10CCH804AAB 45
59. Remove the bolt (1) securing the intake pipe support
clamp.
RCPH10CCH811AAB 46
60. Loosen the clamp (1) and remove the intake elbow
and pipe assembly (2) from the air cleaner outlet.
RCPH10CCH810AAB 47
47533563 18/04/2013
10.1 [10.001] / 14

61. Remove the two fasteners (1) securing the two
halves of the engine drive shaft cover.
RCPH10CCH812AAB 48
62. Remove the cover bolts (1). Remove the covers and
set aside.
RCPH10CCH813AAB 49
63. Mark the drive shaft (1). Remove the four bolts (2)
and disengage the drive shaft from the flywheel.
RCPH10CCH817AAB 50
64. Remove the two bolts (1) securing the front engine
mount bracket. Remove the bracket (2) and set
aside.
RCPH10CCH814AAB 51
47533563 18/04/2013
10.1 [10.001] / 15

65. Remove the two bolts (1) securing the right rear en-
gine mount plate. Remove the plate (2) and set
aside.
RCPH10CCH815AAB 52
66. Remove the two bolts (1) securing the left rear engine
mount plate. Remove the plate (2) along with the
ground strap (3) and set aside.
RCPH10CCH816AAB 53
67. Remove the hose clamp (located at the rear of the
engine) securing the hydraulic hoses. Move the as-
sembly (from the left side of the engine) off to the
side.
RCPH10CCH829AAB 54
68. WARNING
Heavy objects!
Lift and handle all heavy components us-
ing lifting equipment with adequate ca-
pacity. Always support units or parts with
suitable slings or hooks. Make sure the
work area is clear of all bystanders.
Failure to comply could result in death or
serious injury.
W0398A
Use an appropriate device to support the engine, and
carefully remove the engine making sure all hoses,
lines and harnesses are disconnected. RCPH10CCH832AAB 55
47533563 18/04/2013
10.1 [10.001] / 16

69. Remove the rear engine mount. Inspect for wear
and/or damage. Replace as required. Repeat for
the left side.
RCPH07CCH166AAB 56
70. Remove the bolt and nut (1) securing the front mount
engine mount (2). Inspect mount for wear and/or
damage. Replace as required.
RCPH10CCH833AAB 57
Next operation:
Engine - Install (10.001)
47533563 18/04/2013
10.1 [10.001] / 17

Engine - Install
Prior operation:
Engine - Remove (10.001)
NOTE: During the assembly of components with O-ring seals, new seals should be lubricated and installed.
1. Install the rear engine mounts.
RCPH07CCH166AAB 1
2. If front engine mount brackets (4) were removed, re-
install and secure with the four(4) bolts (1) previously
removed.
3. Torque the bolts to 110 - 113 N·m (81 - 83 lb ft).
4. Position the mount (3), install the bolt and torque the
nut (2) to 160 - 220 N·m (118 - 162 lb ft).
RCPH10CCH833AAB 2
5. WARNING
Heavy objects!
Lift and handle all heavy components us-
ing lifting equipment with adequate ca-
pacity. Always support units or parts with
suitable slings or hooks. Make sure the
work area is clear of all bystanders.
Failure to comply could result in death or
serious injury.
W0398A
Support the engine with proper lifting equipment and
lower the engine into position in the front frame.
RCPH10CCH832AAB 3
47533563 18/04/2013
10.1 [10.001] / 18

6. Install the front mount bracket (1).
7. Install the bolts (2) removed previously, and torque
to 31 - 36 N·m (23 - 27 lb ft).
RCPH10CCH814AAB 4
8. Install the plate (1) for the right rear mount.
9. Install the bolts (2) removed previously, and torque
to 125 - 150 N·m (92 - 111 lb ft).
RCPH10CCH815AAB 5
10. Install the plate (1) for the left rear mount.
11. Install the bolts (2) removed previously, along with
the grounding strap (3), and torque to 125 - 150 N·m
(92 - 111 lb ft).
RCPH10CCH816AAB 6
12. Align the marks (1) and attach the drive shaft.
13. Install the four bolts (2) removed previously, and
torque to 101 - 113 N·m (74 - 83 lb ft).
RCPH10CCH817AAB 7
47533563 18/04/2013
10.1 [10.001] / 19

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

14. Position the two sections of drive shaft cover (1) and
secure with the bolts (2) removed previously.
RCPH10CCH813AAB 8
15. Install two new plastic fasteners (1) through the cover
halves.
RCPH10CCH812AAB 9
16. At the left side of the engine, install the rear tube sup-
port bracket (1). Using the bolts (2) removed earlier,
secure bracket to the engine.
RCPH10CCH800AAB 10
17. Install the front tube support bracket (1). Using the
bolts (2) removed earlier, secure bracket to the en-
gine.
18. Connect the cab heater supply (3) and return (3)
tubes, and tighten the nuts.
19. Connect the air bleed hose (5) and engage the
clamp.
20. Install the fill tube (6) from the deaeration tank to the
elbow, and tighten the clamp.
RCPH10CCH038BAB 11
47533563 18/04/2013
10.1 [10.001] / 20

21. At the rear of the engine, install the hydraulic clamp
assembly (1) that was removed earlier.
RCPH10CCH829AAB 12
22. Install the elbow and pipe assembly (1) to the air
cleaner outlet , and tighten the hose clamp (2).
RCPH10CCH810AAB 13
23. With the bolt removed earlier, secure the clamp (1)
for the air cleaner outlet pipe to the bracket
RCPH10CCH811AAB 14
24. Move the pipe between air cleaner outlet and tur-
bocharger inlet into position. Connect the pipe elbow
(1) onto the turbo inlet, but do not tighten the clamp
(2) at this time.
RCPH10CCH809AAB 15
47533563 18/04/2013
10.1 [10.001] / 21

25. Install the opposite end (1) of the pipe into the air
cleaner outlet hose. Do not tighten the hose clamp
(2) at this time. Secure the pipe support with the bolt
(3) removed earlier.
RCPH10CCH804AAB 16
26. Using the bolts (1) remove earlier, secure the intake
pipe support to the bracket.
NOTICE: Tighten all hose clamps at this time. It is impor-
tant to have all hose clamps properly tighten to prevent dirt
from entering the intake system.
RCPH10CCH808AAB 17
27. Move the engine blow-by tube (1) into position. At
the air intake pipe, install the hose connection and
engage the clamp (2).
RCPH10CCH805AAB 18
28. Connect the blow-by tube to the engine and engage
the clamp (1).
RCPH10CCH807AAB 19
47533563 18/04/2013
10.1 [10.001] / 22

29. Move the exhaust pipe assembly (1) into position.
Engage the turbo to pipe clamp (2). Do not tighten
the clamp at this time.
RCPH10CCH806AAB 20
30. Move the exhaust pipe connector (1) between the
turbo outlet and converter inlet elbow. Engage the
lower (shown) (2) and upper (3) clamps and tighten.
Using the bolt (4) removed earlier, secure the support
clamp.
RCPH10CCH803AAB 21
31. Connect the DEF supply and return hoses (1) to the
supply modiule.
RCPH10CCH359AAB 22
32. Connect the DEF harness connector (1) to the mod-
ule.
RCPH10CCH801AAB 23
47533563 18/04/2013
10.1 [10.001] / 23

33. With help of an assistant or an appropriate lifting de-
vice, move the line and harness assembly (1) over
the engine. Secure to the hood support with the four
bolts (2) removed earlier.
RCPH10CCH037BAB 24
34. Inspect the rubber mounts (right side shown) (1) for
the line and harness assembly. Replace as neces-
sary. Place the support alignment holes over the
studs, and secure with the washers and nuts (2) re-
moved earlier.
RCPH10CCH572AAB 25
35. Connect the elbow (1) to the deaeration tank, and
tighten the hose clamp (2).
RCPH10CCH795AAB 26
36. Install the starter solenoid wire (1), secure with the
screw (2) removed earlier and reinstall the plug (3).
RCPH10CCH818AAB 27
47533563 18/04/2013
10.1 [10.001] / 24

CASE IH Magnum 290 Powershift Transmission (PST) Tractor Service Repair Manual (PIN ZCRD02585 and above).pdf

More Related Content

More from f7useijdkd8id (20)

Recently uploaded (20)

CASE IH Magnum 290 Powershift Transmission (PST) Tractor Service Repair Manual (PIN ZCRD02585 and above).pdf