Case ih magnum 310 powershift transmission (pst) tier 4 b tractor service repair manual (pin zerf04500 and above)

Printed in U.S.A.
Copyright © 2014 CNH Industrial America LLC. All Rights Reserved.
Case IH is a registered trademark of CNH Industrial America LLC.
Racine Wisconsin 53404 U.S.A.
Magnum 250
Magnum 280
Magnum 310
Magnum 340
Powershift Transmission (PST)
Tractor
PIN ZERF04500 and above
Part number 47685449
1st
edition English
May 2014
SERVICE MANUAL

Link Product / Engine
Product Market Product Engine
Magnum 250 696110023 PST
TIER 4b [ZERF04500 - ]
North America F2CFE613G*B002
Magnum 280 696110033 PST
North America F2CFE614G*B003
Magnum 310 696110043 PST
North America F2CFE614D*B003
Magnum 340 696110053 PST
North America F2CFE614C*B003
47685449 08/05/2014

Contents
INTRODUCTION
Engine....................................................................................... 10
[10.001] Engine and crankcase ............................................................. 10.1
[10.101] Cylinder heads ..................................................................... 10.2
[10.202] Air cleaners and lines .............................................................. 10.3
[10.216] Fuel tanks .......................................................................... 10.4
[10.218] Fuel injection system............................................................... 10.5
[10.304] Engine lubrication system.......................................................... 10.6
[10.310] Aftercooler.......................................................................... 10.7
[10.400] Engine cooling system ............................................................. 10.8
[10.414] Fan and drive ...................................................................... 10.9
[10.500] Selective Catalytic Reduction (SCR) exhaust treatment ......................... 10.10
Power coupling........................................................................... 19
[19.100] Drive shaft.......................................................................... 19.1
[19.110] Flywheel damper .................................................................. 19.2
[19.120] Drive shaft shield assembly ........................................................ 19.3
Transmission.............................................................................. 21
[21.105] Powershift transmission lubrication system ........................................ 21.1
[21.113] Powershift transmission ............................................................ 21.2
[21.135] Powershift transmission external controls.......................................... 21.3
[21.155] Powershift transmission internal components...................................... 21.4
[21.200] Dropbox ............................................................................ 21.5
[21.900] Hydraulic pump drive............................................................... 21.6
Four-Wheel Drive (4WD) system .................................................. 23
[23.202] Electro-hydraulic control ........................................................... 23.1
[23.314] Drive shaft.......................................................................... 23.2
47685449 08/05/2014

Front axle system ....................................................................... 25
[25.100] Powered front axle ................................................................. 25.1
[25.102] Front bevel gear set and differential ............................................... 25.2
[25.108] Final drive hub, steering knuckles, and shafts ..................................... 25.3
[25.122] Axle suspension control............................................................ 25.4
Rear axle system........................................................................ 27
[27.100] Powered rear axle.................................................................. 27.1
[27.106] Rear bevel gear set and differential................................................ 27.2
[27.120] Planetary and final drives .......................................................... 27.3
Power Take-Off (PTO)................................................................. 31
[31.104] Rear electro-hydraulic control...................................................... 31.1
[31.110] One-speed rear Power Take-Off (PTO) ............................................ 31.2
[31.114] Two-speed rear Power Take-Off (PTO) ............................................ 31.3
[31.146] Front Power Take-Off (PTO) ....................................................... 31.4
Brakes and controls .................................................................... 33
[33.110] Parking brake or parking lock ...................................................... 33.1
[33.202] Hydraulic service brakes ........................................................... 33.2
[33.220] Trailer brake hydraulic control...................................................... 33.3
[33.224] Trailer brake pneumatic control .................................................... 33.4
Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.102] Pump control valves................................................................ 35.2
[35.106] Variable displacement pump ....................................................... 35.3
[35.114] Three-point hitch control valve ..................................................... 35.4
[35.124] Three-point hitch hydraulic adjustment ............................................ 35.5
[35.204] Remote control valves ............................................................. 35.6
[35.300] Reservoir, cooler, and filters........................................................ 35.7
[35.304] Combination pump units ........................................................... 35.8
47685449 08/05/2014

Pneumatic system ...................................................................... 36
[36.100] Pneumatic system.................................................................. 36.1
Hitches, drawbars, and implement couplings.................................. 37
[37.110] Rear three-point hitch .............................................................. 37.1
[37.162] Front hitch.......................................................................... 37.2
Steering..................................................................................... 41
[41.101] Steering control .................................................................... 41.1
[41.200] Hydraulic control components...................................................... 41.2
[41.206] Pump ............................................................................... 41.3
Wheels...................................................................................... 44
[44.520] Rear wheels........................................................................ 44.1
Cab climate control ..................................................................... 50
[50.100] Heating ............................................................................. 50.1
[50.200] Air conditioning..................................................................... 50.2
[50.300] Cab pressurizing system ........................................................... 50.3
Electrical systems....................................................................... 55
[55.010] Fuel injection system............................................................... 55.1
[55.012] Engine cooling system ............................................................. 55.2
[55.014] Engine intake and exhaust system................................................. 55.3
[55.024] Transmission control system....................................................... 55.4
[55.045] Front axle control system .......................................................... 55.5
[55.046] Rear axle control system........................................................... 55.6
[55.050] Heating, Ventilation, and Air-Conditioning (HVAC) control system................. 55.7
[55.051] Cab Heating, Ventilation, and Air-Conditioning (HVAC) controls................... 55.8
[55.100] Harnesses and connectors......................................................... 55.9
[55.130] Rear three-point hitch electronic control system ................................. 55.10
[55.201] Engine starting system ........................................................... 55.11
47685449 08/05/2014

[55.301] Alternator......................................................................... 55.12
[55.302] Battery............................................................................ 55.13
[55.404] External lighting .................................................................. 55.14
[55.408] Warning indicators, alarms, and instruments .................................... 55.15
[55.510] Cab or platform harnesses and connectors...................................... 55.16
[55.512] Cab controls...................................................................... 55.17
[55.513] Cab transmission controls........................................................ 55.18
[55.518] Wiper and washer system........................................................ 55.19
[55.640] Electronic modules ............................................................... 55.20
[55.988] Selective Catalytic Reduction (SCR) electrical system .......................... 55.21
[55.DTC] FAULT CODES.................................................................. 55.22
Platform, cab, bodywork, and decals............................................. 90
[90.100] Engine hood and panels ........................................................... 90.1
[90.102] Engine shields, hood latches, and trims ........................................... 90.2
[90.124] Pneumatically-adjusted operator seat.............................................. 90.3
[90.150] Cab................................................................................. 90.4
[90.151] Cab interior......................................................................... 90.5
[90.160] Cab interior trim and panels........................................................ 90.6
47685449 08/05/2014

INTRODUCTION
47685449 08/05/2014
1

INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The information in this manual is up-to-date at the date of the publication. It is the policy of the manufacturer for
continuous improvement. Some information could not be updated due to modifications of a technical or commercial
type, or changes to the laws and regulations of different countries.
In case of questions, refer to your CASE IH Sales and Service Networks.
47685449 08/05/2014
3

INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
47685449 08/05/2014
4

INTRODUCTION
Safety rules - General maintenance safety
General maintenance safety
Keep the area used for servicing the machine clean and dry. Clean up spilled fluids.
Service the machine on a firm, level surface.
Install guards and shields after you service the machine.
Close all access doors and install all panels after servicing the machine.
Do not attempt to clean, lubricate, clear obstructions, or make adjustments to the machine while it is in motion or while
the engine is running.
Always make sure that working area is clear of tools, parts, other persons and pets before you start operating the
machine.
Unsupported hydraulic cylinders can lose pressure and drop the equipment, causing a crushing hazard. Do not leave
equipment in a raised position while parked or during service, unless the equipment is securely supported.
Jack or lift the machine only at jack or lift points indicated in this manual.
Incorrect towing procedures can cause accidents. When you tow a disabled machine follow the procedure in this
manual. Use only rigid tow bars.
Stop the engine, remove the key, and relieve pressure before you connect or disconnect fluid lines.
Stop the engine and remove the key before you connect or disconnect electrical connections.
Scalding can result from incorrect removal of coolant caps. Cooling systems operate under pressure. Hot coolant can
spray out if you remove a cap while the system is hot. Allow the system to cool before you remove the cap. When
you remove the cap, turn it slowly to allow pressure to escape before you completely remove the cap.
Replace damaged or worn tubes, hoses, electrical wiring, etc.
The engine, transmission, exhaust components, and hydraulic lines may become hot during operation. Take care
when you service such components. Allow surfaces to cool before you handle or disconnect hot components. Wear
protective equipment when appropriate.
When welding, follow the instructions in the manual. Always disconnect the battery before you weld on the machine.
Always wash your hands after you handle battery components.
47685449 08/05/2014
5

SERVICE MANUAL
Engine
Magnum 250 696110023 PST TIER 4b [ZERF04500 - ]
47685449 08/05/2014
10

Engine - Engine and crankcase
Engine - Remove
Prior operation:
Battery - Disconnect (55.302)
Prior operation:
Hood - Remove (90.100)
Prior operation:
Side shield - Remove (90.102)
Prior operation:
Air conditioning - Recover (50.200)
Prior operation:
Engine cooling system - Emptying (10.400)
Prior operation:
Engine cooling system - Remove (10.400)
Prior operation:
Diesel Oxidation Catalyst (DOC) - Remove (10.500)
NOTE: Clean all fittings before disconnecting.
NOTE: Cap or plug all lines and ports when disconnecting hydraulic components.
1. Disconnect the humidity sensor (1) and the air restric-
tion sensor (2). Disengage the hose clamp (3) and dis-
connect the hose from the air intake tube.
RAIL13TR04202AA 1
2. Disconnect the clamps (1) from each end of the air
intake tube and remove the tube.
RAIL13TR04211AA 2
47685449 08/05/2014
10.1 [10.001] / 3

3. Cut the wire tie (1) securing the harness to the hood
support (2).
RAIL13TR04204AA 3
4. Disconnect the starter cables (1) and the auxiliary wire
(2).
RAIL13TR04209AA 4
5. Remove the three bolts (1) securing the hood support
to the frame.
RAIL13TR04209AA 5
6. Remove the hood support.
RAIL13TR04212AA 6
47685449 08/05/2014
10.1 [10.001] / 4

7. Disconnect the high pressure A/C hose (1) and the
coolant lines (2). Cap or plug all fittings and lines.
RAIL13TR04230AA 7
8. Remove the two bolts (1) from the rear engine mount
plate.
RAIL13TR04243AA 8
9. Remove the engine mount cover plate.
RAIL13TR04244AA 9
10. Disconnect the front suspended axle electrical con-
nectors (1) if equipped.
RAIL13TR04237AA 10
47685449 08/05/2014
10.1 [10.001] / 5

11. On the rear of the engine, remove the oil cooler tube
clamp (1). Move the oil cooler lines to the side.
RAIL13TR04236AA 11
12. Disconnect the low pressure A/C line (1). Cap or plug
all fittings and hoses.
RAIL13TR04228AA 12
13. Disengage the hose clamp and disconnect the engine
controller oil line (1).
RAIL13TR04227AA 13
14. Remove the three mounting bolts (1) securing the fuse
panel bracket.
NOTE: Cut any wire ties securing the harness.
RAIL13TR04216AA 14
47685449 08/05/2014
10.1 [10.001] / 6

15. Remove the fuse panel.
RAIL13TR04214AA 15
16. Disconnect the harness connector (1) for the engine
grid heater and the power supply cable (2).
RAIL13TR04219AA 16
17. Disconnect the vent hose (1) from the intake manifold.
RAIL13TR04218AA 17
18. Disconnect the harness connector (1) for the fan drive.
RAIL13TR04220AA 18
47685449 08/05/2014
10.1 [10.001] / 7

19. Remove the A/C compressor mounting bolt (1) and
disconnect the ground wire (2).
RAIL13TR04224AA 19
20. Disconnect the harness connector (1) to the A/C pres-
sure switch.
RAIL13TR04223AA 20
21. Disconnect the alternator excite wire connector (1)
and the CAN bus connector (2).
RAIL13TR04221AA 21
22. Remove the nut and disengage the alternator output
cable (2).
RAIL13TR04231AA 22
47685449 08/05/2014
10.1 [10.001] / 8

23. Disconnect the engine controller connector (1).
RAIL13TR04226AA 23
24. Remove the bolts (1) and cover for the drop box drive
shaft. Set the cover aside.
RCPH10CCH813AAB 24
25. Mark the drive shaft (1). Remove the four bolts and
disengage the drive shaft from the flywheel.
RCPH10CCH817AAB 25
26. Remove the bolts (1) from the plate (2) for the right
hand rear engine mount.
RCPH10CCH925AAB 26
47685449 08/05/2014
10.1 [10.001] / 9

27. Attach appropriately rated lifting equipment to the lift-
ing brackets on the engine. Carefully remove the
engine while making certain all harnesses, lines and
hoses have been disconnected.
RAIL13TR04247AA 27
28. Remove the right hand rear engine mount. Inspect for
wear and/or damage. Replace as required. Repeat
for the left hand side.
RCPH07CCH166AAB 28
29. Remove the four bolts (1) securing the brackets (2) for
the front engine mount.
30. Remove the bolt (3) securing the front engine mount
(4).
31. Inspect the mount for wear and/or damage. Replace
as required.
RCPH10CCH833AAB 29
Next operation:
Engine - Install (10.001)
47685449 08/05/2014
10.1 [10.001] / 10

Engine - Install
Prior operation:
Engine - Remove (10.001)
1. If removed, install the front engine mounting brackets
(1).
2. Torque the four mounting bolts (2) to 101 - 113 N·m (75
- 83 lb ft).
3. Torque the ISO mount support bolt nut (3) to 160 -
220 N·m (118 - 162 lb ft).
RCPH10CCH833AAB 1
4. Install the right (shown) and left rear engine ISO
mounts.
RCPH07CCH166AAB 2
5. Properly support the engine. Raise and move the en-
gine into the front support frame.
RAIL13TR04248AA 3
6. Install the holding plate (1) for the right rear engine
mount with the bolts (2) removed earlier.
7. Torque the bolts to 125 - 150 N·m (92.2 - 110.6 lb ft).
8. Install the bolts (3) removed earlier, and torque to 125
- 150 N·m (92 - 111 lb ft).
9. Install the hood support bolt and washer (4) and torque
to 125 - 150 N·m (92 - 111 lb ft).
RCPH10CCH925AAB 4
47685449 08/05/2014
10.1 [10.001] / 11

10. Making sure the marks (1) are aligned, attach the en-
gine output drive shaft to the engine flywheel.
11. Using the four bolts (2) removed earlier to secure the
drive shaft to the flywheel.
12. Torque the bolts to 101 - 113 N·m (75 - 83 lb ft).
RCPH10CCH817AAB 5
13. Install the engine output drive shaft cover (1). Use the
bolts (2) removed earlier to secure the cover to the
flywheel housing.
RCPH10CCH813AAB 6
14. Connect the harness connector (1) to the engine con-
troller.
RAIL13TR04226AA 7
15. Connect the alternator output cable (1) and secure
with the nut removed previously.
RAIL13TR04231AA 8
47685449 08/05/2014
10.1 [10.001] / 12

16. Connect the alternator excite wire connector (1) and
the CAN bus connector (2).
RAIL13TR04221AA 9
17. Connect the harness connector (1) to the A/C pres-
sure switch.
RAIL13TR04223AA 10
18. Connect the ground wire (1) and secure the wire with
the A/C compressor mounting bolt (2).
RAIL13TR04224AA 11
19. Connect the harness connector (1) for the fan drive.
RAIL13TR04220AA 12
47685449 08/05/2014
10.1 [10.001] / 13

20. Connect the vent hose (1) to the intake manifold.
RAIL13TR04218AA 13
21. Connect the harness connector (1) for the engine grid
heater and the power supply cable (2).
RAIL13TR04219AA 14
22. Install the fuse panel.
RAIL13TR04214AA 15
23. Secure the fuse panel bracket with the three mounting
bolts (1) removed previously. Secure the harness with
wire ties.
RAIL13TR04216AA 16
47685449 08/05/2014
10.1 [10.001] / 14

24. Connect the oil line (1) and secure with the hose clamp
removed previously.
RAIL13TR04213AA 17
25. Lubricate a new O-ring with PAG or mineral oil and
install the O-ring. Connect the low pressure A/C line
(1).
RAIL13TR04228AA 18
26. On the rear of the engine, secure the oil cooler tubes
with the tube clamp (1) previously removed.
RAIL13TR04236AA 19
27. Connect the front suspended axle electrical connec-
tors (1) if equipped.
RAIL13TR04237AA 20
47685449 08/05/2014
10.1 [10.001] / 15

28. Install the cover plate for the left hand rear engine
mount. Torque the bolts (1) to 125 - 150 N·m (92.2
- 110.6 lb ft).
RAIL13TR04243AA 21
29. Lubricate a new O-ring with PAG or mineral oil and
install the O-ring; reconnect the high pressure A/C
hose (1).
30. Reconnect he coolant lines (2).
RAIL13TR04230AA 22
31. Install the hood support.
RAIL13TR04212AA 23
32. Torque the bolts (1) to 125 - 150 N·m (92.2 - 110.6 lb
ft).
RAIL13TR04209AA 24
47685449 08/05/2014
10.1 [10.001] / 16

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

33. Connect the starter cables (1) and the auxiliary wire
(2).
RAIL13TR04209AA 25
34. Install a wire tie (1) to secure the harness to the hood
support (2).
RAIL13TR04204AA 26
35. Install the air intake tube (1) and secure with the hose
clamps (2) previously removed.
RAIL13TR04211AA 27
36. Connect the harness connectors for the humidity sen-
sor (1) and the air restriction sensor (2). Connect the
hose (3) to the air intake tube. Secure the hose with
the hose clamp previously removed.
RAIL13TR04202AA 28
Next operation:
Air conditioning - Evacuate (50.200)
Next operation:
47685449 08/05/2014
10.1 [10.001] / 17

Engine - Cylinder heads
Valve cover - Remove - Over head components
Prior operation:
Hood - Remove (90.100)
Prior operation:
Air conditioning - Recover (50.200)
Prior operation:
Engine cooling system - Emptying (10.400)
NOTE: During the disassembly of components with O-ring seals, it is recommended that the seals be discarded and
new seal installed during assembly.
NOTE: Cap all fittings and plug all lines/hoses as they are disconnected.
1. Loosen the hose clamp (1) at the air cooler inlet.
RAIL13TR04527AA 1
2. Loosen the hose clamp (1) on the opposite end of the
air cooler inlet and remove the inlet tube.
RAIL13TR04526AA 2
3. Remove the oil cooler tube clamp (1).
RAIL13TR04534AA 3
47685449 08/05/2014
10.2 [10.101] / 3

4. Disconnect the hydraulic lines (1) using special tool
380000795.
NOTE: Be prepared to collect some hydraulic oil by placing
a pan under the fitting.
RAIL13TR04535AA 4
5. Disconnect the air conditioning high pressure hose
from the tube fitting (1) and the coolant hose (2).
RAIL13TR04537AA 5
6. Remove the hydraulic tube clamp (1) from the hydraulic
tube.
RAIL13TR04536AA 6
7. Remove the hydraulic cooler lines (1) on each side of
the cooler ( left side shown).
RAIL13TR04530AA 7
47685449 08/05/2014
10.2 [10.101] / 4

8. Disconnect the low pressure A/C line (1), loosen the
hose clamps (2) securing the overflow hose.
RAIL13TR04542AA 8
9. Disconnect the overflow hose (1) and remove the top
bracket mounting bolts (2).
RAIL13TR04543AA 9
10. Remove the two mounting bolts (1) on the rear of the
top bracket and remove the bracket.
RAIL14TR00391AA 10
11. Disconnect the electrical connector (1), the coolant
hoses (2) and the DEF fluid line (3) from the dosing
valve.
RAIL13TR04188AA 11
47685449 08/05/2014
10.2 [10.101] / 5

12. Remove the NOx sensor (1) from the exhaust pipe.
RAIL13TR04185AA 12
13. Disconnect the electrical connector (1) for the temper-
ature sensor.
RAIL13TR04183AA 13
14. Disengage the clamp (1) from the exhaust pipe to the
turbo.
RAIL13TR04177AA 14
15. Disengage the clamp (1) from the exhaust pipe to the
Diesel oxidation catalyst (DOC)
RAIL13TR04180AA 15
47685449 08/05/2014
10.2 [10.101] / 6

16. Remove the two nuts (1) from the C-clamp (2) secur-
ing the exhaust pipe. Remove the exhaust pipe and
set aside.
RAIL13TR04181AA 16
17. Disengage the clamp (1) from the outlet side of the
catalyst.
RAIL13TR04192AA 17
18. Remove the two nuts (1) from the catalyst mounting
straps.
RAIL13TR04190AA 18
19. Slide the catalyst forward from under the support
bracket. Remove the catalyst.
RAIL13TR04193AA 19
Next operation:
Remove the valve cover.
Next operation:
47685449 08/05/2014
10.2 [10.101] / 7

Case ih magnum 310 powershift transmission (pst) tier 4 b tractor service repair manual (pin zerf04500 and above)

More Related Content

Similar to Case ih magnum 310 powershift transmission (pst) tier 4 b tractor service repair manual (pin zerf04500 and above) (10)

More from ufjsjekskem (20)

Recently uploaded (20)

Case ih magnum 310 powershift transmission (pst) tier 4 b tractor service repair manual (pin zerf04500 and above)