Case ih mx285 tractor service repair manual

Case ih mx285 tractor service repair manual

• 1.
  Rac 6-12723 ©2005 1 Issued 10-02 (Revised 08-05) MX Magnum - Service Manual Complete Table of Contents Description Book Number Section Number Publication Number Standard Torque Specifications 1 1000 6-14200 Safety, General Information/Maintenance Schedule 1 1001 6-14200 General Specifications and Special Torques 1 1002 6-14200 Engine Removal and Installation 1 2002 6-14200 Fuel Tank Removal and Installation 1 3001 6-14200 Electrical System (Prior to P.I.N. JAZ129933) How it Works and Troubleshooting 2 4001 6-14210 Electrical System (P.I.N. JAZ129933 and After) How it Works and Troubleshooting 2A 4001 6-12741 Steering Column and Steering Hand Pump 3 5001 6-14221 Powershift Transmission System How it Works and Troubleshooting 3 6000 6-14221 Transmission Input Shaft and Drive Plate 3 6001 6-14221 Input Drop Box 3 6002 6-14221 Engine Frame and Input Drop Box Split 3 6003 6-14221 Speed to Range Transmission Split 3 6005 6-14221 Speed Transmission 3 6006 6-14221 Range Transmission to Rear Frame Split 3 6007 6-14221 Range Transmission 3 6008 6-14221 Transmission Control Valves and Inching Valve 3 6009 6-14221 Rear Frame 4 6011 6-14231 Hydraulic Pump Drive 4 6012 6-14231 Mechanical Front Drive MFD Control System How it Works 4 6013 6-14231 Differential Lock Control System How it Works 4 6014 6-14231 MFD Clutch And Output Shaft Removal Without Tractor Split 4 6015 6-14231 MFD Drive Shaft 4 6016 6-14231 Limited Slip MFD Differential 4 6017 6-14231
• 2.
  MX Magnum MX210,MX230, MX255, MX285 Rac 6-12723 © 2005 2 Issued 10-02 (Revised 08-05) Locking MFD Differential 4 6018 6-14231 Rear Axle and Planetaries 4 6019 6-14231 Power Take Off Control System How it Works 4 6020 6-14231 MFD Planetary Hub, Steering Knuckle, and Axle Drive Shaft 4 6022 6-14231 Suspension MFD Axle 4 6023 6-14231 Suspended MFD Axle System How It Works and Troubleshooting 4 6024 6-14231 Brake Valve 4 7001 6-14231 Brake Cylinders 4 7002 6-14231 Park Brake 4 7004 6-14231 Trailer Brake System - How It Works 4 7005 6-14231 PTO Assembly - Single and Dual Speeds 4A 6021 7-86731 PTO Clutch Assembly Single and Reversible Single Speeds 4A 6025 6-17540 How to Read Symbols in a Hydraulic Schematic 5 8000 6-14241 Hydraulic System How it Works with Troubleshooting 5 8001 6-14241 PTO and Differential Lock Valve 5 8002 6-14241 Remote Valve and Coupler Service 5 8003 6-14241 Remote Hydraulic System How it Works and Troubleshooting 5 8004 6-14241 Priority and Regulator Valve 5 8005 6-14241 Charge Pump 5 8006 6-14241 PFC Piston Pump and Hydraulic Filter 5 8007 6-14241 Hitch System - How it Works 5 8008 6-14241 Hitch Control Valve 5 8009 6-14241 Pedal & Pedal Switch Adjustments 5 9001 6-14241 Cab Raise/Removal and Installation 5 9005 6-14241 Tilt And Fixed Hoods, A/C Condenser, Radiator, And Air-To-Air Aftercooler 5 9008 6-14241 Description Book Number Section Number Publication Number
• 3.
  MX Magnum MX210,MX230, MX255, MX285 Rac 6-12723 © 2005 3 Issued 10-02 (Revised 08-05) Air Conditioning Troubleshooting 5 9010 6-14241 Air Conditioner System Service 5 9020 6-14241 Viscous Fan Drive Test 5 9030 6-14241 Standard Instrumentation Programming and Fault Codes 6 10001 6-14250 Hitch Controller Calibration and Fault Codes 6 10002 6-14250 Transmission Controller (With Suspended Axle) Calibration and Fault Codes 6 10003 6-14250 Armrest Controller Calibration and Fault Codes 7 10004 6-14260 Remote Hydraulics Controller Calibration and Fault Codes 7 10005 6-14260 PTO Controller Configuration and Fault Codes 7 10006 6-14260 Performance Monitor Controller Fault Codes 7 10008 6-14260 Instrument Cluster (ICU2) Programming and Fault Codes 8 10009 6-17550 Description Book Number Section Number Publication Number
• 4.
  MX Magnum MX210,MX230, MX255, MX285 Rac 6-12723 © 2005 4 Issued 10-02 (Revised 08-05) Service Information Packaged with 6-12722 Electrical Schematic (Prior to P.I.N. JAZ129933). . . . . . . . . . 6-12750 Electrical Schematic (P.I.N. JAZ129933 and After) . . . . . . . . . 6-17260 Hydraulic Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12830 Loctite Product Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-98902 A/C Temperature Poster. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13060 Service Information Not Packaged with 6-12723 But Required for Engine Repair Electronic 8.3L Engine for MX255 and MX285 Manual Numbers 7-88622 and 7-88631 Mechanical 8.3L Engine for MX210 and MX230 Manual Number 7-65440
• 5.
  Section 1001 1001 CASE CORPORATION 700 StateStreet Racine, WI 53404 U.S.A. Rac 6-13960 © 2002 Case Corporation Printed in U.S.A. November, 2002 SAFETY, GENERAL INFORMATION / MAINTENANCE SCHEDULE
• 6.
  1001-3 Rac 6-13960 Issued11-02 Printed in U.S.A. Template Name: SM_2_col Template Date: 1994_04_05 Alt= to hide template information Alt+ to display template information SAFETY THIS SAFETY ALERT SYMBOL INDICATES IMPORTANT SAFETY MESSAGES IN THIS MANUAL. WHEN YOU SEE THIS SYMBOL, CAREFULLY READ THE MESSAGE THAT FOLLOWS AND BE ALERT TO THE POSSIBILITY OF PERSONAL INJURY OR DEATH. M171B To prevent injury always follow the Warning, Caution and Danger notes in this section and throughout the manual. Put the warning tag shown below on the key for the key switch when servicing or repairing the machine. One warning tag is supplied with each machine. Additional tags are available from your service parts supplier. Before servicing a machine, park the machine on hard level ground. Turn off the engine, apply the parking brake and remove the key from the key switch. Put blocks in front of and behind either the front or rear wheels. WARNING: Read the operators manual to familiarize yourself with the correct control functions. M489 WARNING: Operate the machine and equipment controls from the seat position only. Any other method could result in serious injury. M490 WARNING: This is one man machine, no riders allowed. M491 201L95 ! ! ! WARNING: Before starting engine study Operators Manual safety messages. Read all safety signs on machine. Clear the area of other persons. Learn and practice safe use of controls before operating. It is your responsibility to understand and follow manufacturers instructions on machine operation, service, and to observe pertinent laws and regulations. Operator and Service Manuals may be obtained from your equipment dealer. M103A WARNING: If you wear clothing that is too loose or do not use the correct safety equipment for your job, you can be injured. Always wear clothing that will not catch on objects. Extra safety equipment that can be required includes hard hat, safety shoes, ear protection, eye or face protection, heavy gloves and reflector clothing. M492 WARNING: When working in the area of the fan belt with the engine running, avoid loose clothing if possible, and use extreme caution. M493 WARNING: When doing checks and tests on the equipment hydraulics, follow the procedures as they are written. DO NOT change the procedure. M494 WARNING: When putting the hydraulic cylinders on this machine through the necessary cycles to check operation or to remove air from a circuit, make sure all people are out of the way. M495 ! ! ! ! !
• 7.
  1001-4 Rac 6-13960 Issued11-02 Printed in U.S.A. Template Name: SM_2_col Template Date: 1994_04_05 Alt= to hide template information Alt+ to display template information WARNING: Always wear heat protective gloves to prevent burning your hands when handling heated parts. SM121A WARNING: Lower all attachments to the ground or use stands to safely support the attachments before you do any maintenance or service. M496 WARNING: Hydraulic oil or diesel fuel leaking under pressure can penetrate the skin and cause infection or other injury. To Prevent Personal Injury: Relieve all pressure, before disconnecting fluid lines. Before applying pressure, make sure all connections are tight and components are in good condition. Never use your hand to check for suspected leaks under pressure. Use a piece of cardboard or wood for this purpose. If injured by leaking fluid, see your doctor immediately. SM171A WARNING: When removing hardened pins such as a pivot pin, or a hardened shaft, use a soft head (brass or bronze) hammer or use a driver made from brass or bronze and a steel head hammer. M497 WARNING: When using a hammer to remove and install pivot pins or separate parts using compressed air or using a grinder, wear eye protection that completely encloses the eyes (approved goggles or other approved eye protectors). M498 WARNING: Use suitable floor (service) jacks or chain hoist to raise wheels or tracks off the floor. Always block machine in placed with suitable safety stands. M499 ! ! ! ! ! ! WARNING: When servicing or repairing the machine. Keep the shop floor and operators compartment and steps free of oil, water, grease, tools, etc. Use an oil absorbing material and or shop cloths as required. Use safe practices at all times. M500 WARNING: Some components of this machine are very heavy. Use suitable lifting equipment or additional help as instructed in the Service Manual. M501 WARNING: Engine exhaust fumes can cause death. If it is necessary to start the engine in a closed place, remove the exhaust fumes from the area with an exhaust pipe extension. Open the door and get outside air into the area. M502 WARNING: When the battery electrolyte is frozen, the battery can explode if (1), you try to charge the battery, or (2), you try to jump start and run the engine. To prevent the battery electrolyte from freezing, try to keep the battery at full charge. If you do not follow these instructions, you or others in the area can be injured. M503 WARNING: Batteries contain acid and explosive gas. Explosions can result from sparks, flames or wrong cable connections. To connect the jumper cables correctly to the battery of this machine see the Operators Manual. Failure to follow these instructions can cause serious injury or death. M504 ! ! ! ! !
• 8.
  1001-5 Rac 6-13960 Issued11-02 Printed in U.S.A. Template Name: SM_2_col Template Date: 1994_04_05 Alt= to hide template information Alt+ to display template information GENERAL INFORMATION Cleaning Clean all metal parts except bearings, in mineral spirits or by steam cleaning. Do not use caustic soda for steam cleaning. After cleaning, dry and put oil on all parts. Clean oil passages with compressed air. Inspection Check all parts when the parts are disassembled. Replace all parts that have excessive wear or are damaged. Small scoring or grooves can be removed with a hone or crocus cloth. Complete visual inspection for indications of wear, pitting and the replacement of parts necessary will prevent early failures. Bearings Clean bearings with a good clean solvent and permit to air dry. DO NOT DRY BEARINGS WITH COMPRESSED AIR. Check bearings for smooth easy action. If the bearing has a loose fit or rough action, the bearing must be replaced. Needle Bearings Before you press needle bearings into a bore, always remove any metal protrusions in the bore or the edge of the bore. Before you press bearings into position, put petroleum jelly on the inside and outside diameter of the bearing. Gears Check all gears for excessive wear or damage. Replace gears as necessary. Oil Seals, O-rings and Gaskets Always install new oil seals, O-rings and gaskets. Put petroleum jelly on seals and O-rings. Shafts Check all shafts for excessive wear or damage. Check the bearing and oil seal surfaces on the shafts for excessive wear or damage. Replace shafts as necessary. Service Parts Always install genuine Case service parts. When ordering refer to the Parts Catalog for the correct part number of the genuine Case replacement items. Failures due to the use of other than genuine Case replacement parts are not covered by warranty. Lubrication Use only the oils and lubrication specified in the Operators or Service Manual. Failures due to the use of non specified oils and lubricants are not covered by warranty.
• 9.
  1001-6 Rac 6-13960 Issued11-02 Printed in U.S.A. Template Name: SM_2_col Template Date: 1994_04_05 Alt= to hide template information Alt+ to display template information MAINTENANCE SCHEDULE Note A -In severe or wet conditions, Interval is every 10 hours or daily. Note B - Perform initial service in first 50 hours of operation. Service Interval Maintenance Requirement Check Grease Change Clean When Warning Message Displays Air Cleaner Element X Every 10 Hours Or Daily Engine Oil Level X Engine Coolant Level X Transmission Oil Level X Every 50 Hours Engine Primary Fuel Filter - Drain Water Every 100 Hours Front Hitch (If Equipped) X Every 300 Hours Battery Water Level X Engine Air Intake Hoses X Engine Coolant Level-Deaeration Tank X *Engine Oil And Filter X Front And Rear Wheel Bolt Torques X Front Axle And Rear Hitch (Note A) X Fuel Tank - Drain Water Differential And Planetary Oil Level (Note B) X Every 600 Hours Engine Coolant Antifreeze Protection X Engine Coolant Filter X Engine Coolant Hoses And Clamps X Engine Fuel Filters X Changeable PTO Internal Splines X Every 1200 Hours Or Annually Engine Primary And Secondary Air Filter X Engine Air Precleaner X Differential and Planetary Oil X Every 1200 Hours Engine Valve Adjustment (Model 210 & 230) (Note C) X Every 1500 Hours Transmission Oil, Filter(s) and Breather X Every 2400 Hours Engine Coolant And Coolant Conditioner X Engine Fuel Injection Nozzles and Pump See (Note C) X Engine Crankshaft Dampener (Note C) X As Required Cab Air And Recirculation Filters X X Cab Air Filter Dust Valve X Engine Primary Air Filter X Grill Screens, Radiator, Condenser/Fuel Cooler, Oil Cooler, Air to Air Cooler X Serpentine Belt X Tire Pressure X
• 10.
  Section 2002 2002 CASE CORPORATION 700 StateStreet Racine, WI 53404 U.S.A. Rac 6-13130 © 2002 Case Corporation Printed in U.S.A. October, 2002 ENGINE REMOVAL AND INSTALLATION
• 11.
  4 Rac 6-13130 Issued10-02 ENGINE REMOVAL STEP 1 96R-28A Park the tractor on a hard, level surface. Put the transmission shift lever in PARK. Turn off the engine and remove the key. Place blocks in front of and behind the rear wheels. Drain the radiator coolant into a suitable, clean container. STEP 2 RD02E069 Remove the toolbox and battery cover. Disconnect the negative (-) battery cable. Disconnect the positive (+) battery cable. STEP 3 RD02E060 Lift up and remove the air cleaner door from the left side of the tractor. Remove the front windshield washer hose (1) from the nozzle on the fixed hood. Remove the four nuts (2) and lift the fixed hood from the right side of the tractor. STEP 4 RD02F129 Remove the left lower fixed hood panel. WARNING: Check and service cooling system according to maintenance instructions. Hot coolant can spray out if the deaeration tank cap is removed while system is hot. To remove the adoration tank cap, let system cool, turn to the first notch, then wait until all the pressure is released. Scalding can result from the fast removal of the adoration tank cap. M855 ! 12
• 12.
  5 Rac 6-13130 Issued10-02 STEP 5 RD02F134 Disconnect the main wiring harness connector. STEP 6 RD02F130 Tag and disconnect the electrical plugs from the fuse box. Remove the electrical plug for the tilt hood front lamps. Remove the tilt hood. Refer to Section 9008 in this service manual for the procedure. STEP 7 RD02F132 Remove the passive terminator harness. STEP 8 RD02F131 Remove the starter solenoid from the hood support. STEP 9 RD02F133 Remove the windshield washer reservoir electrical connectors.
• 13.
  6 Rac 6-13130 Issued10-02 STEP 10 2-14 RD02F146 On electronic injection pump models, remove the fuel supply line (1) and the return line (2). Disconnect the electronic injection pump wiring harness connector (3). STEP 11 RD02F141 RD02F175 On mechanical injection pump models, remove the optional foot throttle cable (1), if equipped, the hand throttle cable (2), the fuel supply line (3), and the engine wiring harness connector (4). STEP 12 RD02F150 Disconnect the ether start tube from the intake manifold on the left side of the engine. 1 2 3 1 2 3 4
• 14.
  7 Rac 6-13130 Issued10-02 STEP 13 RD02F143 Disconnect the electrical connectors from the air filter sensor (1) on the air cleaner outlet tube. Disconnect the electrical plug (2) for the intake manifold temperature sensor. Remove the three harness and hose retainers (3) on the left side of the engine. STEP 14 RD02F152 Remove the left and right fan shields by removing the bolt (1) and pulling out on the shield. STEP 15 RD02F137 Remove the air cleaner outlet tube at the turbocharger elbow clamp (1). Loosen and remove the turbocharger elbow at the turbo clamp (2). Loosen the clamp (3) at the turbo outlet pipe. STEP 16 RD02F144 RD02F157 Remove the upper hose clamps (1) at the air-to-air aftercooler. Remove the hose clamps (2) from the aftercooler tubes to the intake manifold and the turbo. Remove the aftercooler tubes. Tag and remove the three hoses (3) from the deaeration tank. Remove the air cleaner outlet tube (4) at the air cleaner rubber elbow clamp. STEP 17 RD02F151 Trace the line back to the injection pump, so the correct line is removed. Disconnect the fuel return line from the fuel injection pump at the fuel cooler. 1 2 3 1 1 3 2 1 1 3 2 24
• 15.
  8 Rac 6-13130 Issued10-02 STEP 18 RD02F153 Tag and remove the two wires (1) from the back of the alternator and the battery cable. Remove the upper radiator hose at the clamp (2). STEP 19 RD02F171 Remove the lower radiator hose at the hose clamp (1). Remove the heater return hose at the hose clamp (2). STEP 20 RD02F173 Hold the shaft (1) of the fan hub on the two flat areas. Remove the fan blade and fan drive by loosening the viscous fan drive adapter (2). IMPORTANT: The viscous fan drive adapter has a left-hand thread. Loosen by turning clockwise. STEP 21 RD02F170 Disconnect the two electrical connectors from the air conditioning compressor high pressure switch (1) and the clutch. Remove the engine fan belt (2). Remove the three air conditioning compressor mounting bolts (3). 2 1 1 2 2 1 3 2 1
• 16.
  9 Rac 6-13130 Issued10-02 STEP 22 RD02F156 Move the air conditioning compressor to the left side of the tractor, with the hoses attached. Securely support the compressor. STEP 23 RD02F139 Remove the aspirator tube hose (1) at the exhaust elbow. Loosen the lower clamp (2) on the exhaust flex pipe. STEP 24 RD02F138 Remove the fixed hood support bolts (1) from both sides of the tractor. Properly support the air cleaner assembly and the hood support and remove from the tractor. Remove the turbo outlet pipe. STEP 25 RD02F172 Remove the heater supply hose (1) from the fitting on the engine block. Remove the cables from the starter terminal (2). Remove the harness and hose retainer attached to the flywheel shield behind the engine block. Move the harnesses and hoses out of the way 1 2 1 1 2 1
• 17.
  10 Rac 6-13130 Issued10-02 STEP 26 RD02F140 Remove the five bolts (1) for the left-hand hood support bracket. Remove the four bolts for the right- hand hood support bracket, along with the engine to frame ground strap. Remove the brackets. STEP 27 2-2 Remove the oil cooler supply tube (1) and the oil cooler return tube (2). STEP 28 RD02F174 Remove the drive shaft shield (1) and the flywheel shield (2). Refer to Section 6001, Transmission Input Shaft and Drive Plate, for the procedure. STEP 29 RD02F176 Make an alignment mark on the end of the drive shaft connected to the engine for installation. Remove the four bolts attaching the front universal joint to the drive plate. Slide the drive shaft back. 1 1 1 2 1 12
• 18.
  11 Rac 6-13130 Issued10-02 STEP 30 4-12 Attach suitable lifting equipment to the front and rear engine lifting brackets. Put a small amount of tension on the hoist. STEP 31 RI01H053 Remove the two front engine mount clamp bolts. Remove the clamp. STEP 32 4-14 Remove the engine. NOTE: Make sure all electrical wires and hoses are disconnected before removing the engine. STEP 33 RI01H055 RI01H052 Inspect the front engine mount support and the iso- mount for damage or wear. Replace, if necessary. STEP 34 4-23CR1 Inspect the two engine rear rubber mounts for damage or wear. Replace, if necessary.
• 19.
  12 Rac 6-13130 Issued10-02 ENGINE INSTALLATION STEP 35 RI01H052 4-23CR1 If removed, assemble the front engine iso-mount and install the rear engine rubber mounts. Tighten the front iso-mount thru bolt to a torque of 160 to 220 Nm (118 to 162 lb ft). STEP 36 RI01H055 If removed, install the front engine mount support and the iso-mount. Tighten the front engine mount support bolts to a torque of 101 to 113 Nm (75 to 83 lb ft). STEP 37 4-14 Properly support the engine. Install the engine into the tractor chassis. NOTE: Make sure all electrical wires and hoses will not be pinched or binding when installing the engine. STEP 38 RI01H053 Install the two front engine mount clamp bolts. Keep tension on the lifting equipment until these bolts are installed. Relieve the tension on the lifting equipment. Tighten the bolts to a torque of 59 to 106 Nm (44 to 78 lb ft).
• 20.
  13 Rac 6-13130 Issued10-02 STEP 39 RD02F176 Using the alignment mark made during the removal, pull the drive shaft forward and install the drive shaft to the drive plate. Tighten the drive shaft yoke bolts to a torque of 58 to 64 Nm (43 to 47 lb ft) for the MX210 and the MX230, 101 to 113 Nm (75 to 83 lb ft) for the MX255 and the MX285. Tighten the bolts in a crossing pattern. NOTE: Use a rubber mallet to lightly tap the outside edge of the top bearing end cap to position it into the keyway of the yoke. Do not use the bolts to pull the bearing end caps into the yoke keyway. STEP 40 RD02F174 Install the drive shaft shield (1) and flywheel shield (2). Refer to Section 6001 in this manual, Transmission Input Shaft and Drive Plate, for the procedure. STEP 41 2-2 Install the oil cooler supply tube (1) and the oil cooler return tube (2). STEP 42 RD02F140 Install the two bolts (1) for the left-hand hood support bracket. Install the two bolts (2) for the flywheel shield. Install the bolt (3) for the oil cooler tube clamp. Install the four bolts for the right-hand hood support bracket, along with the engine to frame ground strap. 2 1 1 2 1 1 2 3
• 21.
  14 Rac 6-13130 Issued10-02 STEP 43 RD02F172 Install the heater supply hose (1) on the engine block fitting. Install the cables on the starter terminal (2). Install the harness and hose retainer attached to the flywheel shield, behind the engine block. Route the harnesses and hoses as shown. STEP 44 RD02F138 Install the turbo outlet pipe. Slightly tighten the clamp at the turbo.Properly support the air cleaner assembly and the hood support and lower into position. Install the fixed hood support bolts (1) on both sides of the tractor. STEP 45 RD02F139 Install the aspirator tube hose clamp (1) at the exhaust elbow. Tighten the exhaust flex pipe lower clamp (2). STEP 46 RD02F170 Position the compressor and hoses on the engine. Install the three air conditioning compressor mounting bolts (1) along with the ground wire terminal (2). Install the engine fan belt. Connect the two electrical connectors leading to the air conditioning compressor high pressure switch and the clutch. 1 2 1 1 1 2 1 2
• 22.
  15 Rac 6-13130 Issued10-02 STEP 47 RD02F173 Hold the shaft (1) of the fan hub on the two flat areas. Install the fan blade and fan drive by tightening the viscous fan drive adapter (2). IMPORTANT: The viscous fan drive adapter has a left-hand thread. Tighten by turning counterclockwise. Do not over tighten the viscous fan drive adapter on installation. STEP 48 RD02F171 Install the lower radiator hose at the hose clamp (1). Install the heater return hose at the hose clamp (2). STEP 49 RD02F153 Install the two wires on the back of the alternator (1), and the battery cable. Install the upper radiator hose at the hose clamp (2). STEP 50 RD02F151 Connect the fuel return line from the fuel injection pump to the fuel cooler. 2 1 1 2 2 1
• 23.
  16 Rac 6-13130 Issued10-02 STEP 51 RD02F157 RD02F144 Install the three hoses (1) at the deaeration tank. Install the aftercooler tubes at the intake manifold and the turbo at the hose clamps (2). Install the air cleaner outlet tube (3) at the air cleaner clamp. Install the aftercooler tube upper hose clamps (4) at the air- to-air aftercooler. STEP 52 RD02F137 Install the turbocharger elbow at the turbo clamp (1). Install the air cleaner outlet tube at the turbocharger elbow clamp (2). Tighten the clamp (3) at the turbo outlet pipe. STEP 53 RD02F143 Install the three harness and hose retainers (1) on the left side of the engine. Install the electrical plug for the intake manifold temperature sensor (2). Install the electrical connectors at the air filter sensor (3) on the air cleaner outlet tube. STEP 54 RD02F150 Connect the ether start tube to the intake manifold on the left side of the engine. 1 2 23 4 4 2 3 1 3 2 1
• 24.
  17 Rac 6-13130 Issued10-02 STEP 55 RD02F141 RD02F175 On mechanical injection pump models, install the optional foot throttle cable (1), if equipped, the hand throttle cable (2), the fuel supply line (3), and the engine wiring harness connector (4). STEP 56 2-14 RD02F146 On electronic injection pump models, install the fuel supply line (1) and the return line (2). Connect the electronic injection pump wiring harness at the connector (3). STEP 57 RD02F133 Install the windshield washer reservoir electrical connectors. 1 2 3 4 1 2 3
• 25.
  18 Rac 6-13130 Issued10-02 STEP 58 RD02F131 Install the starter solenoid on the hood support. STEP 59 RD02F132 Connect the passive terminator harness. STEP 60 RD02F134 Connect the main wiring harness connector (1). Connect the remaining electrical plugs at the fuse box (2). STEP 61 Close the petcock on the hose located under the tractor radiator. Check and replace all filters, as required. Fill the cooling system. Check the coolant level at the coolant reservoir and the deaeration tank. Check all fluid levels before starting the engine. Make sure the transmission shift lever is in PARK. Start the engine briefly. Shut the engine off and recheck all connections and fluid levels. Restart and run the engine. Turn the engine off and remove the key. STEP 62 RD02F130 Install the tilt hood. Refer to Section 9008 for the procedure. Connect the electrical plug for the tilt hood front lamps. STEP 63 RD02F152 Install the left and right fan shields and tighten the bolt (1). 1 2 1
• 26.
  19 Rac 6-13130 Issued10-02 STEP 64 RD02F129 Install the left lower fixed hood panel. STEP 65 RD02E060 Install the fixed hood on the right side of the tractor. Install and tighten the four nuts (1). Install the front windshield washer hose (2) on the nozzle of the fixed hood. Install the air cleaner door on the left side of the tractor. STEP 66 RD02E069 Connect the positive (+) battery cable, first. Connect the negative (-) battery cable. Install the battery cover and toolbox. STEP 67 96R-28A Remove the wheel blocks. 21
• 27.
  3001-3 Rac 6-13110 Issued10-02 SPECIAL TORQUES Bolts on cab steps ............................................................................................................37 to 67 Nm (27 to 49 lb ft) FUEL TANK General STEP 1 96R-28A Before removing the fuel tank, do the following: 1. Park the tractor on a hard, level surface. 2. Place the transmission control lever in PARK. 3. Shut off the engine and remove the key. 4. Put blocks in front of and in back of the rear wheels. Removal STEP 2 95-12 Remove the six step mounting bolts (1). Move the steps away from the tractor. STEP 3 4-25F Drain the fuel tank. Fuel tank capacities are listed in the chart below. Fuel Tank 210/230 255/285 Standard 492 L (130 gal) 605 L (160 gal) Optional 605 L (160 g) 1 1
• 28.
  Thank you verymuch for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
• 29.
  3001-4 Rac 6-13110 Issued10-02 STEP 4 50-23F Move the left rear wheel out on the axle as far as possible to provide clearance when removing the left tank. The wheel can also be removed. STEP 5 95-18 Disconnect the connector for the fuel level sending unit. Remove the fuel vent hose (1). STEP 6 38-5ECU2 Loosen hose clamp on crossover hose from the bottom of the right fuel tank. STEP 7 95-24- Remove the pressure equalization hose at the front of the cab from the top left-hand fuel tank. STEP 8 95-15R Remove two bolts from each of the two lockdown plates. STEP 9 101R-19A With prybars, lift up on the main tank and move it out a few inches. Insert a plug into the crossover hose as it comes off of the right tank. This will capture the remaining fuel in the tank. 1
• 30.
  3001-5 Rac 6-13110 Issued10-02 STEP 10 91-27CU Disconnect the fuel supply line (2). Disconnect the fuel return line. NOTE: Right tank removed for photographic purposes. STEP 11 5-27-3 Remove the left tank. STEP 12 38-5 Remove the fuel level sending unit (1), crossover hose (2), fuel supply fitting (3) and the fuel return fitting (4). STEP 13 RD02B105 If the right tank is to be removed, remove the tool box and battery cover. STEP 14 RD02B106 Remove the battery cables and move to the side. Remove the batteries. STEP 15 91-27CU If not already removed, loosen the clamp (1) on the fuel crossover hose. Slip the hose off the neck leading into tank. NOTE: Tank removed for photographic purposes. 1 2 1 2 3 4 1
• 31.
  3001-6 Rac 6-13110 Issued10-02 STEP 16 5-20 Remove the two bolts from the lockdown plate on the right tank. STEP 17 101R-23A Lift the right tank free of the support bracket and remove the tank. STEP 18 RD02B107 Use a jack to support the bottom of the tank support bracket while removing the bolts (1) from the left- and right-hand side of the bracket. NOTE: Bolts are shown on left side. Installation STEP 19 RD02B107 Use a jack to lift the support bracket into position and install and tighten all the retaining bolts (1). NOTE: Left hand side shown. STEP 20 38-5ECU1 Install the fuel level sending unit. Connect the crossover hose on the left tank while on the floor. STEP 21 101R-19A Install the fuel tank onto the support brackets with enough room to attach fittings. 1 1 1 1
• 32.
  3001-7 Rac 6-13110 Issued10-02 STEP 22 91-27CU Connect the fuel supply hose (1) and fuel return hose. STEP 23 95-15R Move the left fuel tank into final position. Install and tighten two bolts through each of the two lockdown plates. STEP 24 95-24 Install the pressure equalization hose on the top front of the left tank. Tighten clamp. STEP 25 95-18ECU Install the fuel vent hose (1) and reposition the hose clip. Install the connector for the fuel level sending unit by the fuel vent line. STEP 26 5-23 Position the wheels to the desired position on the rear axle. STEP 27 101R-23A Move the right tank into position. 1 1
• 33.
  3001-8 Rac 6-13110 Issued10-02 STEP 28 91-27CU Connect the crossover hose (shown) and the loose end of the pressure equalization hose connected to the left tank. STEP 29 5-20 Install and tighten the two bolts on the hold-down plate. STEP 30 RD02B106 Install the batteries. STEP 31 RD02B105 Install battery cover and toolbox. STEP 32 95-12 Move steps into position. Install six bolts and tighten to a torque of 37 to 67 Nm (27 to 49 lb ft). STEP 33 Install fuel and check for leaks.