Case ih mxu limited series 110 tractor service repair manual

87659935 3/07
Replaces 87520755
© 2007 CNH America LLC
Printed In U.S.A.
MXU VALUE AND LIMITED SERIES
100, 110, 115, 125, 130, 135,
AND
MAXXUM VALUE AND PRO SERIES
110, 115, 120, 125, 130, AND 140
SECTION 00 - GENERAL 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 01 - SEPARATING THE TRACTOR 3. . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 10 - ENGINE 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 18 - CLUTCH 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 21 - TRANSMISSION SYSTEMS 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 23 - DRIVE LINES 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 25 - MECHANICAL FRONT AXLE 29. . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 27 - MECHANICAL REAR WHEEL DRIVE 33. . . . . . . . . . . . . . . . . . . .
SECTION 31 - POWER TAKE-OFF 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 33 - BRAKING SYSTEM 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 35 - HYDRAULIC SYSTEMS 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 41 - STEERING 65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 44 - FRONT AXLE AND WHEELS 68. . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 50 - AUXILIARY UNITS 69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 55 - ELECTRICAL SYSTEM 72. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The following pages are the collation of the contents pages from each section and chapter
of the MXU Series and Maxxum Series Repair manual. Complete Repair part # 87659930.
The sections used through out all Case IH product Repair manuals may not be used for
each product. Each Repair manual will be made up of one or several books. Each book
will be labeled as to which sections are in the overall Repair manual and which sections
are in each book.
The sections listed above are the sections utilized for the MXU Series and Maxxum
Series Tractors.

2
Some sections of this Repair Manual have been revised to include the New Maxxum Value
and Pro Series Models 110, 115, 120, 125, 130, and 140.
Please note the following to locate new Maxxum Tractor Model Repair information:
For complete engine repair information for the new Maxxum Series Tractors use
Engine Repair Manual # 87661796.
Most all repairs can be carried out by following the Tractor’s systems and specific product
configurations in the repair manual. Example; 16 x16 Transmission, Air Conditioning and
MXU Value Series Closed Center Hydraulic System.
“MXU Value Series” Repair Information also applies to the New Maxxum Value Series
Models.
Where Specific Maxxum Tractor Models are not identified use the following MXU to Maxxum
cross reference:
Maxxum Tractor Models Use MXU tractor Model
Maxxum 110 MXU 110
Maxxum 115 MXU 115
Maxxum 120 MXU 110
Maxxum 125 MXU 125
Maxxum 130 MXU 130
Maxxum 140 MXU 135

87659937 3/07© 2007 CNH America LLC
Printed In U.S.A.
INFORMATION
With the introduction of the Maxxum Series Tractors, controller identifications codes have changed. Also,
the location of the diagnostic connector has changed. The updated Repair Manual # 87659930 does not
contain the new controller ID’s or the new location of the diagnostic connector. This page shows the Maxxum
Series controller identification codes and the diagnostic connector location.
NOTE: Please insert a copy of this page in the front of each Repair Manual Volume for your reference.
Models covered are:
MAXXUM VALUE TRACTORS
110, 115, 125
MAXXUM PRO SERIES TRACTORS
110, 120, 125, 130, 140
CONTROLLER IDENTIFICATION CODES
The controller identifiers change with the introduction of the MAXXUM range of tractors, eg., Controller DA
for MXU will become Controller DR for MAXXUM range. This is required to be remembered throughout this
Repair Manual. See table below:
Identifier Identifier Controller Function(s)
MXU MAXXUM
DA DR 24x24 Transmission, Electronic Draft Control, Rear PTO,
Differential Lock, Four Wheel Drive
DB DS 16x16 Transmission, Electronic Draft Control, Rear PTO,
Differential Lock, Four Wheel Drive
DD DU (Options) Front PTO, Front Hitch, Front Axle Suspension,
Electronic Hydraulic Remotes
EDC7 EDC16 Engine Control (Engine Side)
HA Enhanced Analogue Digital Instrument Cluster (ADIC)
HB Basic ADIC
GA 12x12 PTO Controller -- Rear PTO, Differential Lock, Four Wheel
Drive
JA Keypad

CONTROLLER FUNCTIONS
Electronic Module
Model/Type 24x24 16x16 24x24
16x16
12x12 24x24
16x16
Function DA(DR) DB(DS) DD(DU) GA EDC7
(EDC16)
Rear PTO n n n
Differential Lock n n n
Four Wheel Drive n n n
Engine Control (vehicle side) n n
Auto Headland Turn
Sequence (HTS)
n n
Electronic Draft Control n n
Front Suspension n
Front PTO n
Front Lift n
Electro-Hydraulic Remotes n
Transmission 24x24 n
Transmission 16x16 n
Engine Control (engine side) n
The controller type is identified by a code which is
attached to each module. The code, for example,
’DB/DS’ identifies it as the module used on a tractor
with a 16x16 transmission controlling those
functions highlighted in the table above.
All the modules on the tractor are linked by the CAN
harness and this also links in the instrument cluster,
gear display (16x16 only) and diagnostic connector.
Refer to the system diagrams in Section 55,
Chapter 1 of this repair manual for full controller
details and inter connectivity.
DIAGNOSTIC CONNECTORS
(ADDITIONAL “C” PILLAR LOCATION)
A single diagnostic port, 2, located behind the trim
under the transmission control levers, or on the right
hand “C” pillar, 1, to interrogate all of the controllers
is incorporated into the wiring harness. With the aid
of special service tool 380000843, the port can be
used to gain access to the on-board H-menu
diagnostics, see Section 55, Chapter 1 of this
Repair Manual for full details, to download software
or to connect in more specialized diagnostic
equipment such as the E.S.T. (Electronic Service
Tool).
C277

SECTION 00 -- GENERAL -- CHAPTER 1 1
SECTION 00 -- GENERAL
Chapter 1 -- General Information
CONTENT
Section Description Page
00 000 General Instructions 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautionary Statements 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Health and Safety 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ecology and the Environment 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Identification 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
International Symbols 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications -- Limited Models 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Dimensions 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications -- Value Tractors 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Dimensions 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minimum Hardware Tightening Torques 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 SECTION 00 -- GENERAL -- CHAPTER 1
GENERAL INSTRUCTIONS
IMPORTANT NOTICE
All maintenance and repair operations described in this manual should be carried out exclusively by authorised
workshops. All instructions should be carefully observed and special equipment where indicated should be used.
Anyone who carries out service operations described without carefully observing these instructions will be
directly responsible for any damage caused.
NOTES FOR EQUIPMENT
Equipment shown in this manual is:
-- designed expressly for use on these tractors;
-- necessary to make a reliable repair;
-- accurately built and strictly tested to offer efficient and long--lasting working life.
NOTICES
The words “front”, “rear”, “right hand”, and “left hand” refer to the different parts as seen from the operator’s seat
oriented to the normal direction of movement of the tractor.

PRECAUTIONARY
STATEMENTS
PERSONAL SAFETY
Throughout this manual and on machine decals, you will find precautionary statements (“DANGER”,
“WARNING”, and “CAUTION”) followed by specific instructions. These precautions are intended for the personal
safety of you and those working with you. Please take the time to read them.
DANGER
This word “DANGER” indicates an immediate hazardous situation that, if not avoided, will result in death or
serious injury. The color associated with Danger is RED.
WARNING
This word “WARNING” indicates a potentially hazardous situation that, if not avoided, could result in death or
serious injury. The color associated with Warning is ORANGE.
CAUTION
This word “CAUTION” indicates a potentially hazardous situation that, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices. The color associated with Caution is
YELLOW.
FAILURE TO FOLLOW THE “DANGER”, “WARNING”, AND “CAUTION” INSTRUCTIONS MAY RESULT IN
SERIOUS BODILY INJURY OR DEATH.
MACHINE SAFETY
The precautionary statement (“IMPORTANT”) is followed by specific instructions. This statement is intended for
machine safety.
IMPORTANT: IMPORTANT: The word “IMPORTANT” is used to inform the reader of something he needs to
know to prevent minor machine damage if a certain procedure is not followed.
INFORMATION
NOTE: NOTE: Instructions used to identify and present supplementary information.

IMPORTANT WARNINGS
The machine is designed and produced exclusively
for agricultural use.
All other use will be considered to be contrary to the
use specified by CNH AMERICA LLC, who cannot be
held liable for damage to property or the machine, or
for personal injuries which may result.
Persons who risk improper use will therefore assume
the responsibility for any consequences arising from
such use.
Compliance with the instructions for use,
maintenance and repairs described in this manual,
are the essential preconditions for use specified by
CNH AMERICA LLC.
The machine must only be used, serviced or repaired
by personnel trained in the relevant working methods
and safety regulations and who have been
authorized to work on the machine.
The user must also observe the rules concerning
general safety and accident prevention, including the
Highway Code when driving on public highways.
Any arbitrary modifications made to this machine will
release CNH AMERICA LLC from any liability
resulting from damage or injury.
CNH AMERICA LLC and all its distribution
organizations, inclusive of, but not restrict to,
national, regional or local distributors, cannot be held
liable for damage resulting from the malfunction of
parts and/or components not approved by CNH
AMERICA LLC.
Under no circumstances will a guarantee be issued
for products made or sold by CNH AMERICA LLC
that are damaged as a result of the malfunction of
parts and/or components not approved by CNH
AMERICA LLC.
TO PREVENT ACCIDENTS
Most accidents and personal injuries taking place in
workshops are due from non-observance of some
essential rules and safety precautions.
The possibility that an accident might occur with any
type of machines should not be disregarded, no
matter how well the machine in question was
designed and built.
A wise and careful service technician is the best
precautions against accidents.
Careful observance of this basic precaution would be
enough to avoid many severe accidents.
DANGER
Never carry out any cleaning, lubrication or
maintenance operations when the engine is running.

SAFETY RULES
Generalities
• Carefully follow specified repair and
maintenance procedures.
• Do not wear rings, wristwatches, jewels,
unbuttoned or flapping clothing such as ties, torn
clothes, scarves, open jackets or shirts with open
zips which could get caught on moving parts. Use
approved safety clothing such as anti--slipping
footwear, gloves, safety goggles, helmets, etc.
• Wear safety glasses with side guards when
cleaning parts using compressed air.
• Damaged or frayed wires and chains are
unreliable. Do not use them for lifting or towing.
• Wear suitable protection such as approved eye
protection, helmets, special clothing, gloves and
footwear whenever welding. All persons
standing in the vicinity of the welding process
should wear approved eye protection. NEVER
LOOK AT THE WELDING ARC IF YOUR EYES
ARE NOT SUITABLY PROTECTED.
• Never carry out any repair on the machine if
someone is sitting on the operator’s seat, except
if they are qualified operators assisting in the
operation to be carried out.
• Never operate the machine or use attachments
from a place other than sitting at the operator’s
seat or at the side of the machine when operating
the fender switches.
• Never carry out any operation on the machine
when the engine is running, except when
specifically indicated. Stop the engine and
ensure that all pressure is relieved from hydraulic
circuits before removing caps, covers, valves,
etc.
• All repair and maintenance operations should be
carried out with the greatest care and attention.
• Disconnect the batteries and label all controls to
warn that the tractor is being serviced. Block the
machine and all equipment which should be
raised.
• Never check or fill fuel tanks or batteries, nor use
starting liquid if you are smoking or near open
flames as such fluids are flammable.
• The fuel filling gun should always remain in
contact with the filler neck. Maintain this contact
until the fuel stops flowing into the tank to avoid
possible sparks due to static electricity build--up.
• To transfer a failed tractor, use a trailer or a low
loading platform trolley if available.
• To load and unload the machine from the
transportation means, select a flat area providing
a firm support to the trailer or truck wheels. Firmly
tie the machine to the truck or trailer platform and
block wheels as required by the transporter.
• Always use lifting equipment of appropriate
capacity to lift or move heavy components.
• Chains should always be safely fastened.
Ensure that fastening device is strong enough to
hold the load foreseen. No persons should stand
near the fastening point.
• The working area should be always kept CLEAN
and DRY. Immediately clean any spillage of
water or oil.
• Never use gasoline, diesel oil or other flammable
liquids as cleaning agents. Use non--flammable
non--toxic proprietary solvents.
• Do not pile up grease or oil soaked rags, as they
constitute a great fire hazard. Always place them
into a metal container.

START UP
• Never run the engine in confined spaces which
are not equipped with adequate ventilation for
exhaust gas extraction.
• Never bring your head, body, arms, legs, feet,
hands, fingers near fans or rotating belts.
ENGINE
• Always loosen the radiator cap very slowly
before removing it to allow pressure in the
system to dissipate. Coolant should be topped up
only when the engine is stopped.
• Do not fill up fuel tank when the engine is running.
• Never adjust the fuel injection pump when the
tractor is moving.
• Never lubricate the tractor when the engine is
running.
ELECTRICAL SYSTEMS
• If it is necessary to use auxiliary batteries, cables
must be connected at both sides as follows: (+)
to (+) and (--) to (--). Avoid short--circuiting the
terminals. GAS RELEASED FROM BATTERIES
IS HIGHLY FLAMMABLE. During charging,
leave the battery compartment uncovered to
improve ventilation. Avoid sparks or flames near
the battery area. Do no smoke.
• Do not charge batteries in confined spaces.
• Always disconnect the batteries before
performing any type of service on the electrical
system.
HYDRAULIC SYSTEMS
• Some fluid coming out from a very small port can
be almost invisible and be strong enough to
penetrate the skin. For this reason, NEVER USE
YOUR HANDS TO CHECK FOR LEAKS, but use
a piece of cardboard or a piece of wood for this
purpose. If any fluid is injected into the skin, seek
medical aid immediately. Lack of immediate
medical attention may result in serious infections
or dermatitis.
• Always take system pressure readings using the
appropriate gauges.
WHEELS AND TYRES
• Check that the tyres are correctly inflated at the
pressure specified by the manufacturer.
Periodically check for possible damage to the
rims and tyres.
• Stay at the tyre side when inflating.
• Check the pressure only when the tractor is
unloaded and tyres are cold to avoid wrong
readings due to over--pressure.
• Never cut, nor weld a rim with the inflated tyre
assembled.
• To remove the wheels, block both front and rear
tractor wheels. Raise the tractor and install safe
and stable supports under the tractor in
accordance with regulations in force.
• Deflate the tyre before removing any object
caught into the tyre tread.
• Never inflate tyres using flammable gases as
they may originate explosions and cause injuries
to bystanders.
REMOVAL AND INSTALLATION
• Lift and handle all heavy components using lifting
equipment of adequate capacity. Ensure that
parts are supported by appropriate slings and
hooks. Use lifting eyes provided to this purpose.
Take care of the persons near the loads to be
lifted.

SECTION 01 -- SEPARATING THE TRACTOR -- CHAPTER 1 1
SECTION 01 -- SEPARATING THE TRACTOR
Chapter 1 -- Separating Front Axle and Front Support from the Engine
CONTENT
Tightening Torques 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overhaul 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Axle and Front Support 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Axle to Support Shim Thickness Calculation 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 SECTION 01 -- SEPARATING THE TRACTOR -- CHAPTER 1
TIGHTENING TORQUES
1
SPECIAL TOOLS
CAUTION
The operations described in this section can only be
carried out with the ESSENTIAL tools indicated by
an (X). To work safely and efficiently and obtain the
best results, it is also necessary to use the
recommended specific tools listed below and certain
other tools, which are to be made according to the
drawings included in this manual.
List of specific tools required for the various
operations described in this section.
380000569 Tractor splitting kit.
380000500 Engine support brackets (with
380000569).
380000844 Engine support adaptor plate (with
380000500).

OVERHAUL
SEPARATING FRONT AXLE AND FRONT
SUPPORT FROM THE ENGINE
Op. 10 001
Removal
DANGER
Lift and handle all heavy components using lifting
equipment of appropriate lifting capacity. Ensure that
units or parts are supported by suitable slings or
hooks. Ensure that no--one is in the vicinity of the load
to be lifted.
1. Drain the cooling system (refer to cooling system
drain in the cooling chapter of the engine
section).
2. Remove the battery cover and disconnect the
battery negative cable (1).
2
3. Using a suitable sling, connect the front weights
to a hoist and remove the front weights (if fitted).
3
4. Loosen the hose clamps (1), remove the pipe
clamp retaining bolt (2) and remove the air cooler
outlet pipe.
4

5. Loosen the pipe clamp (1), hose clamp (2) and
remove the air cooler inlet pipe.
5
6. Loosen the clamp (1) and remove the air cleaner
inlet.
6
Tractors with Air Conditioning
7. Remove the receiver dryer retaining screws from
the retaining bracket.
7
8. Slide out the air conditioning condenser from the
radiator and reposition with the hoses still
attached.
8

All Tractors
9. Loosen the hose clamps (1) and disconnect the
coolant hoses from the radiator.
10. Remove the radiator support (2).
9
11. Loosen the hose clamp (1) and disconnect the
coolant hose.
10
12. Loosen the coolant hose clamp (1) and
disconnect the coolant hose connecting the cab
heater to the radiator.
11
13. Disconnect the steering sensor electrical
connector (if fitted).
12

14. Detach the driveline oil cooler supply and return
pipes from the retaining clamps.
13
15. Disconnect the steering cylinder supply and
return pipes (1).
16. Disconnect the differential lock oil supply pipe (2)
(if fitted).
14
Tractors with Standard Front Axle
17. Remove the four wheel driveshaft guard.
18. Expand the circlip (1) and slide the circlip (1) and
sleeve (2) along the four wheel drive shaft.
15
19. Remove the four wheel driveshaft and the central
support.
16

All Tractors
20. Position the splitting kit (1) 380000569 beneath
the tractor.
21. Use the supports (2), in the the splitting kit to
support the engine on the splitting stand.
17
22. Position wooden wedges (1) between the front
axle and the front support. These prevent
articulation of the axle.
18
23. Using a spreader bar and suitable chains or
slings, attach the front and rear of the support
assembly to a moveable overhead hoist.
WARNING
Always ensure the support is adequately supported
and will remain stable when seperated from the
engine. Failure to provide adequate support may
cause the assembly to be unstable with possible
personal injury if the support tips forwards or
backwards.
24. Remove the front support retaining bolts and
separate the front support from the engine.
19
25. Support the assembly on axle stands at the front
and the rear of the support.
20

Installation
NOTE: If a new front support or the engine oil pan has
been removed and replaced during overhaul it is
necessary to recalculate the new shim thickness to
be installed (refer to front axle to support shim
thickness calculation in this chapter).
1. Make sure the shims (1) are re--positioned in the
same location as when removed.
21
2. Make sure the wooden wedges (1) are between
the front axle and the front support. These
prevent articulation of the axle.
3. Using a spreader bar and suitable chains or
slings, attach the front and rear of the support
assembly to a moveable overhead hoist.
22
4. Align the front support to the engine and install
the front support to engine retaining bolts.
Tighten to the specified torque value.
23
5. Remove the supports (2) and the splitting kit (1).
24

6. Install the four wheel driveshaft and the central
support.
25
sleeve (2) along the four wheel driveshaft.
8. Install the four wheel driveshaft guard.
26
All Tractors
9. Connect the steering cylinder supply and return
pipes (1).
10. Connect the differential lock oil supply pipe (2) (if
fitted).
27
11. Attach the driveline oil cooler supply and return
pipes to the retaining clamps.
28

12. Connect the steering sensor electrical connector
(if fitted).
29
13. Connect the coolant hose and tighten the hose
clamp (1).
30
14. Connect the coolant hose connecting the cab
heater to the radiator and tighten the hose clamp
(1).
31
15. Connect the coolant hoses to the radiator and
tighten the hose clamps (1).
16. Install the radiator support (2).
32

Tractors with Air Conditioning
17. Slide the air conditioning condensor on to the
radiator
33
18. Install the receiver dryer retaining screws to the
retaining bracket.
34
All Tractors
19. Install the air intake pipe and tighten the clamp
(1).
35
20. Install the air cooler inlet pipe. Tighten the pipe
clamp (1) and the hose clamp (2).
36

21. Install the air cooler outlet pipe. Tighten the hose
clamps (1) and install the pipe clamp retaining
bolt (2).
37
to a hoist and install the front weights (if fitted).
38
23. Connect the battery negative cable (1) and install
the battery cover.
24. Refill the cooling system (refer to cooling system
refill in the cooling chapter of the engine section).
25. Refill the driveline with the correct specification
oil.
39

FRONT AXLE TO SUPPORT SHIM
THICKNESS CALCULATION
1. Install a 4.5 mm yellow shim (1) part number
82026240 onto each of the engine mounting
studs.
40
2. Align the front support to the engine and install
the four upper retaining bolts. Tighten to the
specified torque value.
41
3. Using feeler gauges measure space between
each shim and the front support.
42

SECTION 01 -- SEPARATING THE TRACTOR
Chapter 2 -- Separating Engine and Front Support from the
Transmission
CONTENT
Section Description Page
Tightening Torques 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overhaul 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine and Front Support from the Transmission 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TIGHTENING TORQUES
1
SPECIAL TOOLS
CAUTION
The operations described in this section can only be
carried out with the ESSENTIAL tools indicated by
an (X). To work safely and efficiently and obtain the
best results, it is also necessary to use the
recommended specific tools listed below and certain
other tools, which are to be made according to the
drawings included in this manual.
List of specific tools required for the various
operations described in this section.
380000569 Tractor splitting kit.
380000500 Engine support brackets (with
380000569).
380000844 Engine support adaptor plate (with
380000500).
Locally Fabricated Tools:
Cab Jacking Tool x2 (Tractors with standard cab)
2

OVERHAUL
ENGINE AND FRONT SUPPORT FROM THE
TRANSMISSION
Removal
DANGER
Lift and handle all heavy components using lifting
equipment of appropriate lifting capacity. Ensure that
units or parts are supported by suitable slings or
hooks. Ensure that no--one is in the vicinity of the load
to be lifted.
1. Drain the cooling system (refer to cooling system
drain in the cooling chapter of the engine
section).
2. Remove the battery cover and disconnect the
battery negative cable (1).
3
to a hoist and remove the front weights (if fitted).
4
4. Disconnect the exhaust manifold from the
turbocharger (1). Remove the exhaust support
retaining bolts (2) and remove the exhaust
manifold.
5

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

5. Loosen the hose clamp (1) and disconnect the
coolant hose connecting the cab heater to the
radiator.
6
6. Disconnect the battery positive cable (1) from the
starter motor.
7
NOTE: Note the position of the driveline oil cooler
hoses.
7. Loosen the hose clamps (1) and disconnect the
driveline oil cooler hoses.
8. Disconnect the tractor performance monitor
radar electrical connector (2) (if fitted).
8
9. Disconnect the engine harness electrical
connectors.
9

10. Disconnect the cab heater coolant hose (1).
11. Disconnect the air conditioning hoses (2) and (3).
10
NOTE: Note the position of the steering cylinder oil
supply hoses.
12. Disconnect the steering cylinder oil supply hoses
(1) and (2).
11
Tractors with Mechanical Fuel Injection Pump
13. Loosen the retaining nut (1) and detach the
throttle cable from the fuel injection pump (2).
12
All Tractors
14. Disconnect the brake fluid lines (1), (2) and (3)
from the brake fluid reservoir.
13

15. Disconnect the fuel supply and fuel return lines
(1) from the fuel tank level sender.
14
16. Disconnect the differential lock oil supply pipe (1)
15
17. Remove the retaining screw (1) and detach the
flywheel speed sensor (if fitted).
16
Tractors with Standard Cab
18. Loosen the cab front mounting bolt while holding
the nut (1) under the cab floor. Remove the bolt
and washers. Repeat this step for the left hand
side of the cab.
17

19. Using locally fabricated tool (1), raise the cab
evenly.
18
20. Remove the four wheel driveshaft guard.
sleeve (2) along the four wheel driveshaft.
19
22. Remove the four wheel driveshaft and the central
support.
20

All Tractors
21
23. Position splitting kit (4) 380000569 underneath
the tractor.
24. Use the supports (3), in the splitting kit to support
the transmission on the splitting stand.
25. Remove the engine to transmission lower
retaining bolts.
26. Remove two rear oil pan retaining bolts from the
left hand side. Repeat this step for the right hand
side.
27. Install the adaptor plate (1) 380000844 and the
engine support brackets (2) 380000500 between
the engine and the wheeled splitting trolley.

28. Position wooden wedges (1) between the front
axle and the front support. These prevent
articulation of the front axle.
22
29. Check that all necessary hoses tubes and
electrical connectors have been disconnected. It
may be necessary to disconnect additional items
due to other optional equipment that has been
installed on the tractor.
30. Re--check that the engine and transmission are
safely supported on the splitting stand. Remove
the engine to transmission retaining bolts.
31. Remove the front support and engine from the
transmission.
23

Case ih mxu limited series 110 tractor service repair manual

More Related Content

More from fusjfjskekme (20)

Recently uploaded (20)

Case ih mxu limited series 110 tractor service repair manual