Case ih quantum 110 f tractor service repair manual instant download (pin zflk00441 and above)

Printed in U.S.A.
© 2017 CNH Industrial Italia S.p.A. All Rights Reserved.
Case IH is a trademark registered in the United States and many
other countries, owned or licensed to CNH Industrial N.V.,
its subsidiaries or affiliates.
QUANTUM®
80F
QUANTUM®
90F
QUANTUM®
100F
QUANTUM®
110F
Tractor
PIN ZFLK00441 and above
Part number 51523375
English
August 2018
SERVICE MANUAL

Link Product / Engine
Product Market Product Engine
Quantum® 100F With cab
[ZHLK01675 - ]
Australia New Zealand F5DFL413K*C001
[ZHLK01675 - ]
Latin America F5DFL413K*C001
Quantum® 100F Without cab
[ZFLK00441 - ]
Latin America F5DFL413K*C001
[ZFLK00441 - ]
Australia New Zealand F5DFL413K*C001
[ZGLK02439 - ]
Latin America F5DFL413J*C002
[ZGLK02439 - ]
Australia New Zealand F5DFL413J*C002
[ZHLK01638 - ]
Latin America F5DFL413J*C002
[ZHLK01638 - ]
Australia New Zealand F5DFL413J*C002
[ZHLK01644 - ]
Latin America F5DFL413B*H001
[ZHLK01644 - ]
Australia New Zealand F5DFL413B*H001
[ZHLK02413 - ]
Australia New Zealand F5DFL413B*H001
[ZHLK02413 - ]
Latin America F5DFL413B*H001
[ZHLK02445 - ]
Latin America F5DFL413L*C001
[ZHLK02445 - ]
Australia New Zealand F5DFL413L*C001
[ZFLK00985 - ]
Australia New Zealand F5DFL413L*C001
[ZFLK00985 - ]
Latin America F5DFL413L*C001
51523375 20/08/2018

Contents
INTRODUCTION
Engine....................................................................................... 10
[10.001] Engine and crankcase ............................................................. 10.1
[10.114] Pump drives ........................................................................ 10.2
[10.216] Fuel tanks .......................................................................... 10.3
[10.206] Fuel filters .......................................................................... 10.4
[10.202] Air cleaners and lines .............................................................. 10.5
[10.254] Intake and exhaust manifolds and muffler ......................................... 10.6
[10.501] Exhaust Gas Recirculation (EGR) exhaust treatment.............................. 10.7
[10.400] Engine cooling system ............................................................. 10.8
[10.414] Fan and drive ...................................................................... 10.9
[10.310] Aftercooler........................................................................ 10.10
[10.304] Engine lubrication system........................................................ 10.11
Clutch ....................................................................................... 18
[18.100] Clutch mechanical release control ................................................. 18.1
[18.104] Clutch hydraulic release control.................................................... 18.2
[18.110] Clutch and components ............................................................ 18.3
Transmission.............................................................................. 21
[21.114] Mechanical transmission ........................................................... 21.1
[21.130] Mechanical transmission external controls......................................... 21.2
[21.100] Mechanical transmission hydraulic components ................................... 21.3
[21.140] Mechanical transmission internal components..................................... 21.4
[21.112] Power shuttle transmission......................................................... 21.5
[21.134] Power shuttle transmission external controls ...................................... 21.6
[21.104] Power shuttle transmission hydraulic components ................................ 21.7
[21.154] Power shuttle transmission internal components .................................. 21.8
[21.160] Creeper ............................................................................ 21.9
51523375 20/08/2018

[21.162] Reverser ......................................................................... 21.10
[21.168] Hi-Lo unit ......................................................................... 21.11
[21.109] Transmission cooler and lines.................................................... 21.12
[21.118] Transmission/Rear drive ......................................................... 21.13
[21.182] Differential........................................................................ 21.14
Four-Wheel Drive (4WD) system .................................................. 23
[23.202] Electro-hydraulic control ........................................................... 23.1
[23.304] Four-Wheel Drive (4WD) gearbox ................................................. 23.2
[23.314] Drive shaft.......................................................................... 23.3
Front axle system ....................................................................... 25
[25.100] Powered front axle ................................................................. 25.1
[25.102] Front bevel gear set and differential ............................................... 25.2
[25.108] Final drive hub, steering knuckles, and shafts ..................................... 25.3
[25.310] Final drives ......................................................................... 25.4
[25.400] Non-powered front axle ............................................................ 25.5
Rear axle system........................................................................ 27
[27.100] Powered rear axle.................................................................. 27.1
[27.106] Rear bevel gear set and differential................................................ 27.2
[27.120] Planetary and final drives .......................................................... 27.3
[27.126] Spur gear and final drives.......................................................... 27.4
Power Take-Off (PTO)................................................................. 31
[31.101] Rear mechanical control ........................................................... 31.1
[31.142] Front Power Take-Off (PTO) control ............................................... 31.2
[31.146] Front Power Take-Off (PTO) ....................................................... 31.3
Brakes and controls .................................................................... 33
[33.202] Hydraulic service brakes ........................................................... 33.1
[33.110] Parking brake or parking lock ...................................................... 33.2
51523375 20/08/2018

[33.220] Trailer brake hydraulic control...................................................... 33.3
Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.104] Fixed displacement pump.......................................................... 35.2
[35.204] Remote control valves ............................................................. 35.3
[35.100] Main lift system..................................................................... 35.4
[35.114] Three-point hitch control valve ..................................................... 35.5
[35.124] Three-point hitch hydraulic adjustment ............................................ 35.6
[35.160] Front hitch controls and lines ...................................................... 35.7
[35.162] Front hitch cylinders and lines ..................................................... 35.8
Hitches, drawbars, and implement couplings.................................. 37
[37.120] Rear three-point hitch linkage...................................................... 37.1
[37.162] Front hitch.......................................................................... 37.2
[37.166] Front hitch linkage.................................................................. 37.3
[37.110] Rear three-point hitch .............................................................. 37.4
Frames and ballasting ................................................................. 39
[39.140] Ballasts and supports .............................................................. 39.1
Steering..................................................................................... 41
[41.101] Steering control .................................................................... 41.1
[41.200] Hydraulic control components...................................................... 41.2
Wheels...................................................................................... 44
[44.511] Front wheels........................................................................ 44.1
[44.520] Rear wheels........................................................................ 44.2
Cab climate control ..................................................................... 50
[50.100] Heating ............................................................................. 50.1
[50.104] Ventilation .......................................................................... 50.2
[50.200] Air conditioning..................................................................... 50.3
[50.300] Cab pressurizing system ........................................................... 50.4
51523375 20/08/2018

Electrical systems....................................................................... 55
[55.100] Harnesses and connectors......................................................... 55.1
[55.525] Cab engine controls................................................................ 55.2
[55.015] Engine control system.............................................................. 55.3
[55.201] Engine starting system ............................................................. 55.4
[55.301] Alternator........................................................................... 55.5
[55.302] Battery.............................................................................. 55.6
[55.011] Fuel tank system ................................................................... 55.7
[55.010] Fuel injection system............................................................... 55.8
[55.014] Engine intake and exhaust system................................................. 55.9
[55.989] Exhaust Gas Recirculation (EGR) electrical system ............................. 55.10
[55.640] Electronic modules ............................................................... 55.11
[55.513] Cab transmission controls........................................................ 55.12
[55.024] Transmission control system..................................................... 55.13
[55.021] Transmission pressure sensors and switches ................................... 55.14
[55.541] Cab Front-Wheel Drive (FWD) controls.......................................... 55.15
[55.040] Four-Wheel Drive (4WD) control system......................................... 55.16
[55.542] Cab axle controls................................................................. 55.17
[55.522] Cab Power Take-Off (PTO) controls ............................................. 55.18
[55.048] Rear Power Take-Off (PTO) control system ..................................... 55.19
[55.049] Front Power Take-Off (PTO) control system ..................................... 55.20
[55.031] Parking brake electrical system .................................................. 55.21
[55.032] Trailer brake electrical system ................................................... 55.22
[55.512] Cab controls...................................................................... 55.23
[55.035] Remote control valve electric control ............................................ 55.24
[55.051] Cab Heating, Ventilation, and Air-Conditioning (HVAC) controls................. 55.25
[55.050] Heating, Ventilation, and Air-Conditioning (HVAC) control system............... 55.26
[55.523] Cab hitch controls ................................................................ 55.27
51523375 20/08/2018

[55.130] Rear three-point hitch electronic control system ................................. 55.28
[55.518] Wiper and washer system........................................................ 55.29
[55.404] External lighting .................................................................. 55.30
[55.405] External lighting switches and relays ............................................ 55.31
[55.514] Cab lighting ...................................................................... 55.32
[55.408] Warning indicators, alarms, and instruments .................................... 55.33
[55.DTC] FAULT CODES.................................................................. 55.34
Accessories ............................................................................... 88
[88.100] Accessories ........................................................................ 88.1
Platform, cab, bodywork, and decals............................................. 90
[90.150] Cab................................................................................. 90.1
[90.151] Cab interior......................................................................... 90.2
[90.160] Cab interior trim and panels........................................................ 90.3
[90.154] Cab doors and hatches ............................................................ 90.4
[90.110] Operator platform less cab ......................................................... 90.5
[90.118] Protections and footboards......................................................... 90.6
[90.114] Operator protections ............................................................... 90.7
[90.120] Mechanically-adjusted operator seat............................................... 90.8
[90.124] Pneumatically-adjusted operator seat.............................................. 90.9
[90.100] Engine hood and panels ......................................................... 90.10
51523375 20/08/2018

INTRODUCTION
51523375 20/08/2018
1

INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your CASE IH Sales and Service Networks.
51523375 20/08/2018
3

INTRODUCTION
Note to the Owner WARNINGS FOR AIR CONDITIONING SYSTEM
REPAIR OPERATIONS
Quantum® 100F With cab [ZHLK01675 - ] ANZ --- LA
Quantum® 110F With cab [ZGLK02439 - ] ANZ --- LA
Starting the system at low temperatures can damage the compressor. Only operate the air conditioner when the
engine is hot and the temperature inside the cab is at least 20 °C (68.00 °F).
When disconnecting the hoses, close the ends with plastic caps to prevent foreign matter and humidity from getting
inside the hoses.
Handle the thermostatic sensor carefully to avoid damage that may prevent efficient system operation.
Always use two spanners to unscrew the hose fittings to avoid twisting the fitting.
Do not use any type of engine oil to lubricate the compressor and the system.
Never leave the compressor oil container open, always make sure that it is tightly closed. If left exposed the oil will
absorb humidity from the air and may, subsequently, damage the system.
Do not transfer compressor oil from the original container to another container.
Do not introduce any additives to the compressor oil. Any additional substances could contain elements which are
incompatible with the chemical base of the refrigerant and thus alter its characteristics.
Check that the thermostatic sensor is correctly inserted in the fins on the evaporator to ensure efficient system oper-
ation.
51523375 20/08/2018
4

INTRODUCTION
Safety rules SAFETY REGULATIONS
TO PREVENT ACCIDENTS
Most accidents or injuries that occur in workshops are the result of non--observance of simple and fundamental safety
regulations.
For this reason, IN MOST CASES THESE ACCIDENTS CAN BE AVOIDED: by foreseeing possible causes and con-
sequently acting with the necessary caution and care.
Accidents may occur with all types of vehicle, regardless of how well it was designed and built.
A careful and judicious service technician is the best guarantee against accidents.
Precise observance of the most basic safety rule is normally sufficient to avoid many serious accidents.
DANGER: Never carry out any cleaning, lubrication or maintenance operations when the engine is running.
GENERAL
• Carefully follow specified repair and maintenance procedures.
• Do not wear rings, wristwatches, jewellery, unbuttoned or loose articles of clothing such as: ties, torn clothing,
scarves, open jackets or shirts with open zips that may remain entangled in moving parts.
It is advised to wear approved safety clothing, e.g: non--slip footwear, gloves, safety goggles, helmets, etc.
• Do not carry out repair operations with someone sitting in the driver’s seat, unless the person is a trained technician
who is assisting with the operation in question.
• Operate the vehicle and use the implements exclusively from the driver’s seat.
• Do not carry out operations on the vehicle with the engine running, unless specifically indicated.
• Stop the engine and ensure that all pressure is relieved from hydraulic circuits before removing caps, covers, valves,
etc.
• All repair and maintenance operations must be carried out using extreme care and attention.
• Service steps and platforms used in a workshop or in the field should be built in compliance with the safety rules in
force.
• Disconnect the batteries and label all controls to indicate that the vehicle is being serviced. Block the machine and
all equipment which should be raised.
• Do not check or fill fuel tanks, accumulator batteries, nor use starting liquid when smoking or near naked flames,
as these fluids are inflammable.
• Brakes are inoperative if manually released for repair or maintenance purposes.
In such cases, the machine should be kept constantly under control using blocks or similar devices.
• The fuel nozzle should always be in contact with the filling aperture. Maintain this position until filling operations
are completed in order to avoid possible sparks caused by the accumulation of static electricity.
• Only use specified towing points for towing the tractor, connect parts carefully.Make sure that all pins and/or locks
are secured in position before applying traction.
Never remain near the towing bars, cables or chains that are operating under load
• Transport vehicles that cannot be driven using a trailer or a low--loading platform trolley, if available.
• When loading or unloading the vehicle from the trailer (or other means of transport), select a flat area capable
of sustaining the trailer or truck wheels, firmly secure the tractor to the truck or trailer and lock the wheels in the
position.
• Electric heaters, battery--chargers and similar equipment must only be powered by auxiliary power supplies with
efficient ground insulation to avoid electrical shock hazards.
• Always use suitable hoisting or lifting devices when raising or moving heavy parts.
• Take extra care if bystanders are present.
• Never pour gasoline or diesel oil into open, wide and low containers.
• Never use gasoline, diesel oil or other inflammable liquids as cleaning agents. Use non-flammable non-toxic pro-
prietary solvents.
• Wear safety goggles with side guards when cleaning parts with compressed air.
• Limit the air pressure to a maximum of 2.1 bar (30.5 psi), according to local regulations.
51523375 20/08/2018
5

SERVICE MANUAL
Engine
Quantum® 100F With cab [ZHLK01675 - ], Quantum® 100F Without cab
[ZFLK00441 - ], Quantum® 110F With cab [ZGLK02439 - ], Quantum®
110F Without cab [ZHLK01638 - ], Quantum® 80F With cab [ZHLK01644
- ], Quantum® 80F Without cab [ZHLK02413 - ], Quantum® 90F With cab
[ZHLK02445 - ], Quantum® 90F Without cab [ZFLK00985 - ]
51523375 20/08/2018
10

Engine - Engine and crankcase
Engine - Remove from transmission
WARNING
Burn hazard!
Be very careful to avoid contact with hot fluids. If fluid is extremely hot, allow it to cool to a moderately
warm temperature before proceeding.
Failure to comply could result in death or serious injury.
W0362A
WARNING
Hot surface possible!
Wait for all components to cool before performing any operation.
W0251A
CAUTION
Hot area!
Use care when working near hot components. Wear protective gloves.
Failure to comply could result in minor or moderate injury.
C0034A
WARNING
Chemical hazard!
When handling fuel, lubricants, and other service chemicals, follow the manufacturer's instructions.
Wear Personal Protective Equipment (PPE) as instructed. Do not smoke or use open flame. Collect
fluids in proper containers. Obey all local and environmental regulations when disposing of chemi-
cals.
W0371A
Prior operation:
A. Remove the front ballast - See Front ballast - Remove (39.140).
1. Carefully clean the area around the central drain plug
(1) on the transmission.
2. Use a suitable container to collect the transmission oil.
3. Loosen the central drain plug (1) on the transmission
and drain the transmission oil.
4. Replace the central drain plug (1) on the transmission.
5. Tighten the central drain plug (1) on the transmission.
6. Carefully clean all the parts contaminated by any leak-
ing hydraulic fluid.
7. Remove the cab – See Cab and platform - Remove
(90.150).
8. Remove the transmission drive shaft going from the
transmission to the front axle – See Front drive shaft
- Remove (23.314).
MOIL16TR01450AA 1
51523375 20/08/2018
10.1 [10.001] / 3

9. Carefully clean the area around the couplings (1) on the
intermediate delivery and return pipes on the transmis-
sion oil exchanger.
11. Loosen the couplings (1) on the intermediate delivery
and return pipes on the transmission oil exchanger.
MOIL16TR01454AA 2
12. Carefully clean the area around the coupling (1) of
the intermediate differential oil delivery pipe on the
left-hand side of the vehicle.
14. Loosen the coupling (1) of the intermediate differential
oil delivery pipe on the left-hand side of the vehicle.
MOIL16TR01455AA 3
15. Carefully clean the area around the coupling (1) of the
intermediate delivery pipe connected to the transmis-
sion oil filter.
17. Loosen the coupling (1) of the intermediate delivery
pipe connected to the transmission oil filter.
MOIL16TR01456AA 4
19. Carefully clean the area around the sleeve (1) of the
sion oil filter.
21. Loosen the two screw collars (2) on the sleeve (1) of
the intermediate delivery pipe connected to the trans-
mission oil filter.
22. Loosen the screw collar (3) fixing the sleeve (1) of the
sion oil filter.
23. Disconnect the sleeve (1) of the intermediate delivery
MOIL16TR01457AA 5
51523375 20/08/2018
10.1 [10.001] / 4

25. Carefully clean the area around the connector (1) of
the steering sensor.
26. Disconnect the steering sensor connector (1).
27. Disconnect the connector cable (1) from the steering
sensor.
MOIL16TR01459AA 6
the hydraulic fluid pressure sensor.
29. Disconnect the connector (1) of the hydraulic fluid
pressure sensor.
30. Disconnect the connector cable (1) from the hydraulic
fluid pressure sensor.
MOIL16TR01460AA 7
31. Carefully clean the area around the connector (1).
32. Disconnect connector (1).
33. Unclamp the connector (1) from the support bracket
(2).
MOIL16TR01458AA 8
34. Loosen the screw (1) and remove the collar (2).
35. Loosen the sleeve (3) of the oil delivery pipe (4).
MOIL16TR01462AA 9
51523375 20/08/2018
10.1 [10.001] / 5

36. Carefully clean the area around the two holes (1) on
the upper side of the clutch bell (2).
37. Restore the thread in the two holes (1) on the upper
side of the clutch bell (2).
MOIL16TR01463AA 10
38. Loosen the two screws (1) securing the bracket (2).
39. Remove the bracket (2) and the cable (3).
40. Arrange two eyebolts suitable for lifting the engine.
41. Prepare a hoist and chains/straps that are suitable for
lifting the engine.
MOIL16TR01461AA 11
42. Place a suitable lift under the transmission housing.
MOIL16TR01464AA 12
43. Clean the area around the clutch bell (1).
44. Correctly position the two eyebolts (1), and using the
correct screws, lock into the holes on the upper face
of the clutch bell (2).
45. Correctly hook the chains/straps to the eyebolts (1).
46. Use a suitable tool to separate the engine from the
transmission.
MOIL16TR01465AA 13
51523375 20/08/2018
10.1 [10.001] / 6

47. Loosen the four fastening screws (1) on the left-hand
side of the clutch bell.
48. Repeat for the four fastening screws on the right-hand
side of the clutch bell.
MOIL16TR01466AA 14
49. Loosen the four retaining nuts (1) on the lower side of
the clutch bell.
MOIL16TR01467AA 15
50. Using a suitable tool, separate the engine from the
transmission.
MOIL16TR01468AA 16
51. Place a suitable bracket under the clutch bell on the
engine side.
engine side.
MOIL16TR01469AA 17
51523375 20/08/2018
10.1 [10.001] / 7

53. Place a suitable bracket under the support bracket of
the front ballasts.
54. Place a suitable bracket under the support bracket of
the front ballasts.
55. Unclamp the chains on the eyebolts and free the en-
gine.
MOIL16TR01470AA 18
transmission side.
transmission side.
MOIL16TR01471AA 19
51523375 20/08/2018
10.1 [10.001] / 8

Engine - Install to the transmission
1. Retrieve the transmission assembly and carefully clean
the area around the clutch bell.
2. Retrieve the front axle and engine assembly and clean
the clutch bell.
lifting the engine.
lifting the engine.
7. Carefully clean the area around the two holes (1) on
the upper side of the clutch bell (2).
8. Restore the thread in the two holes (1) on the upper
MOIL16TR01463AA 1
9. Correctly position the two eyebolts (1), and using the
correct screws, lock into the holes on the upper face of
the clutch bell (2).
10. Correctly hook the chains/straps to the eyebolts (1).
MOIL16TR01465AA 2
11. Remove any supports positioned under the clutch bell
on the engine side.
MOIL16TR01469AA 3
51523375 20/08/2018
10.1 [10.001] / 9

12. Remove any supports positioned under the support
bracket (1) of the front ballasts.
13. Use a suitable tool to fit the transmission to the engine.
MOIL16TR01470AA 4
14. Apply suitable sealing paste to the coupling face (1)
of the transmission clutch bell.
15. Using a suitable tool, move the engine closer to the
transmission.
MOIL16TR01468AA 5
16. Tighten the four fastening screws (1) on the left-hand
side of the clutch bell and tighten to the prescribed
torque.
17. Repeat for the four fastening screws on the right-hand
MOIL16TR01466AA 6
18. Tighten the four retaining nuts (1) on the lower side of
the clutch bell and tighten to the prescribed torque.
19. Carefully clean all the parts contaminated by any seal-
ing paste residue.
20. Unclamp the chains on the eyebolts and free the en-
gine.
21. Remove the two eyebolts used to lift the engine.
22. Remove any supports positioned under the clutch bell
on the transmission side.
MOIL16TR01467AA 7
51523375 20/08/2018
10.1 [10.001] / 10

23. Remove any supports positioned under the transmis-
sion housing.
MOIL16TR01464AA 8
24. Retrieve and carefully clean the bracket (1).
25. Correctly position the cable (2).
26. Correctly position the bracket (1) in its housing on the
engine.
27. Tighten the two screws (3) which fix the bracket (1) in
place.
MOIL16TR01461AA 9
oil delivery pipe (2).
29. Tighten the sleeve (1) of the oil delivery pipe (2).
30. Retrieve the collar (3) and position it correctly in its
housing.
31. Tighten the fastening screw (4) on the collar (2).
MOIL16TR01462AA 10
the steering sensor.
33. Correctly position the connector cable (1) of the steer-
ing sensor.
34. Connect the steering sensor connector (1).
MOIL16TR01459AA 11
51523375 20/08/2018
10.1 [10.001] / 11

the hydraulic fluid pressure sensor.
36. Correctly position the connector cable (1) of the hy-
draulic fluid pressure sensor.
37. Connect the connector (1) of the hydraulic fluid pres-
sure sensor.
MOIL16TR01460AA 12
38. Carefully clean the area around the connector (1).
39. Fasten the connector (1) to the support bracket (2).
40. Connect the connector (1).
MOIL16TR01458AA 13
sion oil filter.
42. Connect the sleeve (1) of the intermediate delivery
43. Tighten the two screw collars (2) on the sleeve (1) of
the intermediate delivery pipe connected to the trans-
mission oil filter.
44. Tighten the screw collar (3) fixing the sleeve (1) to the
sion oil filter.
MOIL16TR01457AA 14
45. Carefully clean the area around the coupling (1) of the
sion oil filter.
46. Correctly connect the coupling (1) of the intermediate
delivery pipe connected to the transmission oil filter.
47. Tighten the coupling (1) of the intermediate delivery
MOIL16TR01456AA 15
51523375 20/08/2018
10.1 [10.001] / 12

48. Carefully clean the area around the coupling (1) of
the intermediate differential oil delivery pipe on the
left-hand side of the vehicle.
49. Correctly connect the coupling (1) of the intermediate
differential oil delivery pipe on the left-hand side of the
vehicle.
50. Tighten the coupling (1) of the intermediate differential
oil delivery pipe on the left-hand side of the vehicle.
MOIL16TR01455AA 16
51. Carefully clean the area around the couplings (1)
on the intermediate delivery and return pipes on the
transmission oil exchanger.
52. Correctly connect (1) the intermediate delivery and re-
turn pipes to the transmission oil exchanger.
53. Tighten the couplings (1) on the intermediate delivery
and return pipes to the transmission oil exchanger.
54. Refit the transmission drive shaft going from the trans-
mission to the front axle - See Front drive shaft - In-
stall (23.314).
MOIL16TR01454AA 17
Next operation:
A. Reattach the cab – See Cab and platform - Install (90.150).
B. Top up the transmission oil level - See Transmission drive housing - Level make up (21.118).
C. Refit the front ballast - See Front ballast - Install (39.140).
51523375 20/08/2018
10.1 [10.001] / 13

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

Engine - Remove from transmission
WARNING
Burn hazard!
Be very careful to avoid contact with hot fluids. If fluid is extremely hot, allow it to cool to a moderately
warm temperature before proceeding.
W0362A
WARNING
Hot surface possible!
Wait for all components to cool before performing any operation.
W0251A
CAUTION
Hot area!
Use care when working near hot components. Wear protective gloves.
Failure to comply could result in minor or moderate injury.
C0034A
WARNING
Chemical hazard!
When handling fuel, lubricants, and other service chemicals, follow the manufacturer's instructions.
Wear Personal Protective Equipment (PPE) as instructed. Do not smoke or use open flame. Collect
fluids in proper containers. Obey all local and environmental regulations when disposing of chemi-
cals.
W0371A
Prior operation:
A. Remove the front ballast - See Front ballast - Remove (39.140).
1. Carefully clean the area around the central drain plug
(1) on the transmission.
3. Loosen the central drain plug (1) on the transmission
and drain the transmission oil.
4. Replace the central drain plug (1) on the transmission.
5. Tighten the central drain plug (1) on the transmission.
7. Remove the operator platform – See Platform - Re-
move (90.110).
8. Remove the transmission drive shaft going from the
transmission to the front axle – See Front drive shaft
- Remove (23.314).
MOIL16TR01450AA 1
51523375 20/08/2018
10.1 [10.001] / 14

Case ih quantum 110 f tractor service repair manual instant download (pin zflk00441 and above)

More Related Content

Similar to Case ih quantum 110 f tractor service repair manual instant download (pin zflk00441 and above) (16)

More from ufjjskekemem (20)

Recently uploaded (20)

Case ih quantum 110 f tractor service repair manual instant download (pin zflk00441 and above)