Caterpillar Cat 245B SERIES II EXCAVATOR (Prefix 6MF) Service Repair Manual (6MF00513 and up).pdf

Service Repair Manual
Model
245B SERIES II EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 245B EXCAVATOR 6MF
Configuration: 245B SERIES II EXCAVATOR 6MF00513-UP (MACHINE) POWERED BY 3406 ENGINE
Disassembly and Assembly
37-MT, 41-MT, and 42-MT Series Starting Motors
Media Number -SENR3581-04 Publication Date -01/10/2008 Date Updated -24/10/2008
i01557321
General Information
SMCS - 1453
37-MT and 41-MT Starting Motors
Illustration 1 g00782868
37-MT and 41-MT Cross section view
(1) Nut (Battery)
(2) Solenoid Mounting Screws
(3) Pinion
1/3
245B SERIES II EXCAVATOR 6MF00513-UP (MACHINE) POWERED BY 3406 E...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

(4) Pinion Drive Housing Bolts
(5) Shift Lever Housing Bolts
(6) Field Winding Screws
(7) Laminated Core
(8) Rear Housing Bolts
(9) Brush
(10) Commutator
(11) Brush Lead Screws
(12) Motor Terminal Bolt
(13) Motor Terminal Nut
42-MT Starting Motors
42-MT Cross section view
(1) Nut (Battery)
(2) Solenoid Mounting Screws
(3) Pinion
(4) Pinion Drive Housing Bolts
(5) Shift Lever Housing Bolts
2/3
2019/9/10

(6) Field Winding Screws
(7) Laminated Core
(8) Brush
(9) Commutator
(10) Ground Terminal Nut
(11) Brush Lead Screws
(12) Rear Housing Bolt
(13) Motor Terminal Bolt
(14) Motor Terminal Nut
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 22:50:00 UTC+0800 2019
3/3
2019/9/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01559954
Starting Motor - Disassemble - 42-MT
SMCS - 1453-015
Disassemble the Starting Motor
Note: The disassembly and assembly that follows is of the 24 volt starting motor. The 12 volt is
similar.
Table 1
Required Tools
Tool Part Number Part Description Quantity
A 1P-1855 Retaining Ring Pliers 1
B 1P-0510 Driver Gp 1
1/6
2019/9/10

1. Disconnect wire assembly (4) from solenoid (1). Disconnect motor terminal connector (3)
from the starting motor housing.
2. Remove three bolts (2) from the shift lever housing. Do not disassemble the solenoid. The
parts inside the solenoid are not serviceable.
3. Remove the O-ring seal and bushing (5) .
4. Remove the nut (6). Remove the solenoid from the shift lever housing.
2/6
2019/9/10

5. Remove the negative terminal nuts "-", wire assembly (2), and washers. Remove six bolts
(8) and rear housing (7) .
6. If necessary, remove bushing (9) from the rear housing.
3/6
2019/9/10

7. Remove washer (12) from the armature shaft. Lift brush springs (10) and pull the brushes
away from the commutator. Position the brush springs (10) on the side of the brushes in
order to hold the brushes in the holders.
8. Disconnect field winding leads (13) from brush holder (11). Remove the brush holder.
9. Remove brushes (15) and negative "-" terminal (14) from the brush holders.
10. Scribe a line on the pinion drive, the shift lever and the starting motor housings for the
correct alignment at assembly.
11. Remove six bolts (17) and pinion drive housing (16) .
4/6
2019/9/10

12. Remove retainer (18) with tool (A). Remove shift lever pin (20). If necessary, remove the O
-ring seals from the shift lever pin.
13. Remove pinion drive (19) and the shift lever.
14. Remove the brake disc from the armature shaft. Remove five bolts (22), shift lever housing
(21) and the washer. If necessary, remove the outside O-ring seals.
15. If necessary, remove the seal and the bushing from the shift lever housing.
5/6
2019/9/10

16. Remove armature (22) from the starting motor housing.
17. Remove the following components from the starting motor housing: eight screws (26), pole
shoes (25) and field winding coil (24). It may be necessary to use an impact driver to
remove screws (26) .
18. Clean the armature, field winding coil and pinion drive with mineral spirits and a brush.
Note: If the commutator is dirty, the commutator may be cleaned with Number 00
sandpaper. Do not use emery cloth.
19. Inspect all parts for wear and damage.
Tue Sep 10 22:50:56 UTC+0800 2019
6/6
2019/9/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01365545
Starting Motor - Disassemble - 37-MT and 41-MT
SMCS - 1453-015
Disassemble the Starting Motor
Start By:
A. Remove the starting motor from the machine.
Note: The disassembly of the 12 volt starting motor is similar to the disassembly of the 24 volt
starting motor.
Table 1
Required Tools
Tool Part Number Description Quantity
1/7
2019/9/10

1. Disconnect and remove shunt wire assembly (4) and motor terminal connector "MTR" (3)
from the solenoid (1) and starting motor.
2. Remove the plug (5) and seal from the shift lever housing. Remove the nut (6) that is inside
the shift lever housing. The nut holds the plunger to the shift lever.
3. Remove bolts (2) and solenoid (1) from the shift lever housing. Do not disassemble the
solenoid. The parts inside the solenoid are not serviceable.
2/7
2019/9/10

4. Mark the following components for correct assembly: rear housing (8), pinion drive, shift
lever housing and starting motor housing. Remove four bolts (7) and rear housing (8).
Remove washer (9) from the armature. Remove the O-ring seal from the starting motor
housing, if necessary.
3/7
2019/9/10

5. Remove bushing (10) from the rear housing, if necessary.
6. Lift each brush spring (12) and put the spring on the left side of the brush (14). Disconnect
three leads (11) and remove brush holder (13) .
7. Remove brushes (14) from the brush holder.
8. Remove six bolts (16) and pinion drive housing (15) .
4/7
2019/9/10

9. Remove bushing (17) from the pinion drive housing, if necessary.
5/7
2019/9/10

10. Drive retainer (18) backward away from ring (20) that is below the retainer. Remove the
ring and the retainer. Remove armature (19) from pinion drive (21) and the starting motor
and the shift lever housing (23). Remove the washer (22) from the armature (19) .
Note: The pinion drive that is on the 41-MT starting motor is not the same pinion drive that
is shown. The pinion drive is similar to a 42-MT starting motor. Refer to Disassembly and
Assembly, "Starting Motor - Disassemble".
11. Remove pinion drive (21) from the shift lever forks (25) .
12. Remove five bolts (26) and shift lever housing (23). Remove ring (24) with tool (A), pin
(27) and shift lever (25). Remove the seals from the pin, if necessary.
13. Remove the O-ring seal from the shift lever housing, if necessary.
14. Remove seal (28) and bushing (29) from the shift lever housing, if necessary.
6/7
2019/9/10

15. Remove eight screws (32), field winding coil (30), and pole shoes (31) from the starting
motor housing. It may be necessary to use an impact driver to remove screws (32). One of
the screws is the negative terminal.
16. Clean the armature, field winding coil, and pinion drive with mineral spirits and a brush.
Note: If the commutator is dirty, the commutator may be cleaned with Number 00
sandpaper. Do not use emery cloth.
17. Inspect all parts for wear and damage.
Tue Sep 10 22:51:52 UTC+0800 2019
7/7
2019/9/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01560148
Starting Motor - Assemble - 42-MT
SMCS - 1453-016
Assemble the Starting Motor
Table 1
Required Tools
Tool Part Number Part Description Quantity
1. Put SAE 20W oil on all bushings, seals and oil wicks.
1/6
2019/9/10

2. Put field winding coil (24) and pole shoes (25) in position in the starting motor housing. Put
9s-3263 Thread Lock Compound on the threads of screws (26). Tighten screws (26) to a
torque of 20.3 ± 2.3 N·m (179.7 ± 20.4 lb in).
3. Put 5P-0960 Molybdenum Grease on the armature bushing areas. Do not put grease on the
armature core or the commutator. Put armature (23) into the starting motor housing.
4. Install the outside O-ring seals if it is necessary. Install the shift lever housing (21). Install
five bolts (22). Install the brake disc on the armature shaft.
2/6
2019/9/10

5. Install the pinion drive (19) and the shift lever. Install the O-ring seal if it is necessary.
Install the shift lever pin (20). Install the retainer (18) with tool (A) .
6. Align the pinion drive housing (16). Install six bolts (17) .
3/6
2019/9/10

7. Install brushes (15) and negative "-"terminal (14) in the brush holders. Install brush spring
(10) against the side of each brush.
8. Install the brush holder. Connect the field winding leads (13) to the brush holder (11) .
9. Put the washer (12) onto the armature assembly. Push the brushes (10) into the holders so
that the springs are on top of the brushes.
10. Install the bushing (9) into the rear housing if it is necessary.
4/6
2019/9/10

11. Install six bolts (8) and rear housing (7). Torque bolts (8) to 5.7 ± 1.1 N·m (50.4 ± 9.7 lb in).
Install wire assembly (2), washers, and negative terminal nuts "-".
12. Install solenoid (1). Align the solenoid link with the hole in the shift lever. Install three bolts
(2) in the shift lever housing. Torque bolts (2) to 17.8 ± 3.7 N·m (157.5 ± 32.7 lb in).
13. Install wire assembly (4). Connect motor terminal "MTR" (3) to the starter motor housing.
5/6
2019/9/10

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

14. Install pinion clearance adjustment nut (6) .
15. Adjust pinion clearance. Refer to Testing and Adjusting, "Pinion Clearance - Adjust" for
pinion clearance adjustments.
16. Install the O-ring seal and bushing (5) .
Tue Sep 10 22:52:47 UTC+0800 2019
6/6
2019/9/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01559761
Starting Motor - Assemble - 37-MT and 41-MT
SMCS - 1453-016
Assemble the Starting Motor
Table 1
Required Tools
Tool Part Number Description Quantity
1. Put SAE 20W oil on all bushings, seals and oil wicks.
1/9
2019/9/10

2. Put field winding coil (29) and pole shoes (30) in position in the starting motor housing. Put
9s-3263 Thread Lock Compound on the threads of screws (31). Tighten to a torque of 20.3
± 2.3 N·m (179.7 ± 20.4 lb in).
3. Install bushing (27) and seal (28) into the shift lever housing. Use tool group (B) .
4. Put the O-ring on the shift lever housing (22) .
5. Install the seals on pin (26). Hold shift lever (24) in shift lever housing (22) and install pin
(19) through the housing and lever (24). Install ring (23) with tool (A) .
2/9
2019/9/10

6. Put shift lever housing (22) in position on the starting motor housing. Install bolts (25) and
tighten bolts (25) to a torque of 18.9 ± 2.6 N·m (167.3 ± 23.0 lb in).
7. Put 5P-0960 Molybdenum Grease on the armature bushing areas. Do not put grease on the
armature core or the commutator. Install washer (21) on armature (18). Put armature (18)
into the starting motor housing. Hold pinion drive (20) in the shift lever fork and insert
armature (18) through the shift housing and pinion drive.
Note: The pinion drive that is on the 41-MT starting motor is not same pinion drive that is
shown. The pinion drive is similar to a 42-MT starting motor. Refer to Disassembly and
Assembly, "Starting Motor - Assemble".
3/9
2019/9/10

Caterpillar Cat 245B SERIES II EXCAVATOR (Prefix 6MF) Service Repair Manual (6MF00513 and up).pdf

More Related Content

Similar to Caterpillar Cat 245B SERIES II EXCAVATOR (Prefix 6MF) Service Repair Manual (6MF00513 and up).pdf (16)

More from ufjskekdjdmw2 (20)

Recently uploaded (20)

Caterpillar Cat 245B SERIES II EXCAVATOR (Prefix 6MF) Service Repair Manual (6MF00513 and up).pdf