Caterpillar Cat 262D Skid Steer Loader (Prefix KTS) Service Repair Manual (KTS00001 and up).pdf

Service Repair Manual
Models
262D Skid Steer Loader

Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 262D SKID STEER LOADER KTS
Configuration: 262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242520
Engine Oil Pump - Remove and Install
SMCS - 1304-010
Removal Procedure
Start By:
a. Remove the front housing.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/4
262D Skid Steer Loader KTS00001-UP (MACHINE) POWERED BY C3.3B Engine(...
2019/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g02788686
1. Remove screws (2) and cover (1).
2. Remove inner rotor (4) from outer rotor (3).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 129-1967 White Grease 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
2019/11/17

NOTICE
If any part of the engine oil pump is worn or damaged, the complete
assembly of the engine oil pump must be replaced.
1. Ensure that all components of the engine oil pump are clean and free from wear and
damage.
2. Position outer rotor (3) into the pump body. Check the clearance between outer rotor (3) and
the pump body.
3. Install inner rotor (4) into outer rotor (3). Check the clearance between the lobes of outer
rotor (3) and inner rotor (4).
4. Position a strip of Plastigage onto the outer rotor face with Tooling (A). Position cover (1)
and install screws (2) and torque. Remove cover (1) and check clearance between the rotor
and cover (1).
5. Position cover (1) and install screws (2). Tighten screws (2) to a torque of 8 to 9 N·m
(70 to 83 lb in).
3/4
2019/11/17

End By:
a. Install the front housing.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Nov 17 23:38:42 UTC+0800 2019
4/4
2019/11/17

Shutdown SIS
Previous Screen
i05242522
Water Pump - Remove and Install
SMCS - 1361-011; 1361-012
Removal Procedure
Start By:
a. Remove the v-belts.
Values.
1. Refer to Operation and Maintenance Manual, "Coolant - Change" for the proper draining
and filling procedures.
2. Remove bolts (2) and remove pulley (1).
1/2
2019/11/17

3. Remove bolts (4).
4. Remove water pump (3) and discard the gasket. Install a new gasket upon installation.
1. Install water pump (3) in the reverse order of removal.
Sun Nov 17 23:39:41 UTC+0800 2019
2/2
2019/11/17

Dispose of all fluids according to local regulations and mandates.
1. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the
correct draining procedure.
Note: Coolant only needs drained to below the water temperature regulator.
2. Disconnect hose assembly (1).
3. Remove bolts (2) from the water temperature regulator housing . Remove water temperature
regulator elbow (3).
3/4
2019/11/17

4. Remove gasket (5) and remove water temperature regulator (4) from the water temperature
regulator housing.
Note: Note the orientation of the water temperature regulator elbow.
1. Install water temperature regulator (4) in the reverse order of removal.
a. Check the water temperature regulator for correct operation. Refer to System
Operation, Testing and Adjusting, "Water Temperature Regulator - Test" for the
correct procedure to test the water temperature regulator. If any components of the
water temperature regulator housing are worn or damaged, the complete assembly
must be replaced.
Sun Nov 17 23:40:41 UTC+0800 2019
4/4
2019/11/17

NOTICE
1. Remove two bolts (2) from flywheel (1).
2. Install Tooling (A) into the crankshaft.
3. Install Tooling (B) and a suitable lifting device on flywheel (1). The weight of flywheel (1)
is approximately 30 kg (66 lb).
4. Remove remaining bolts (2).
5. Remove flywheel (1) from the cylinder block.
3/6
2019/11/17

6. Inspect flywheel (1) and the ring gear (3) for wear and damage. Replace any worn
components or damaged components.
7. If necessary, remove the flywheel ring gear (3), follow Step 7.a through Step 7.b.
a. Place the flywheel assembly on a suitable support.
b. Use a hammer and a punch in order to remove ring gear (3) from flywheel (1). If
necessary, a torch may be needed to heat ring gear (3).
Note: Identify the orientation of the teeth on the flywheel ring gear (3).
Table 2
Required Tools
A -
Guide Stud
M12 - 1.25 by 100 mm
2
B 138-7573 Link Bracket 1
NOTICE
4/6
2019/11/17

Always wear protective gloves when handling parts that have been
heated.
1. If flywheel ring gear (3) was removed, follow Step 1.a through Step 1.c in order to install
ring gear (3) to flywheel (1).
a. Identify the orientation of teeth on new ring gear (3).
Note: The chamfered side of ring gear teeth must face toward the starting motor when
the flywheel is installed. This position will ensure the correct engagement of the
starting motor.
b. Raise heat of flywheel ring gear (3) in an oven to a maximum temperature of 250 °C
(482 °F) prior to installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear
onto flywheel (1).
5/6
2019/11/17

2. Install Tooling (B) and a suitable lifting device on flywheel (1). The weight of flywheel (1)
is approximately 30 kg (66 lb).
3. Install Tooling (A) into the crankshaft.
4. Use the lifting device to position flywheel (1) onto Tooling (A).
5. Install bolts (2) to flywheel (1).
6. Remove Tooling (A).
7. Install remaining bolts (2) to flywheel (1). Apply engine oil to bolts. Tighten bolts (2) to a
torque of 98 to 107 N·m (72 to 80 lb ft).
8. Check the run out of the flywheel. Refer to Specifications, "Flywheel" for further
information.
Sun Nov 17 23:41:40 UTC+0800 2019
6/6
2019/11/17

Shutdown SIS
Previous Screen
i05242540
Crankshaft Rear Seal and Wear Sleeve - Remove - Includes
Crankshaft Gear
SMCS - 1161-011; 7558-011
Removal Procedure
Start By:
a. Remove the flywheel.
NOTICE
1. Place the engine at top dead center.
1/2
2019/11/17

2. Use a screw driver to remove rear seal (1).
3. Check the alignment of crankshaft gear (2) and camshaft gear (3). Remove crankshaft gear
(2) and ring seal.
4. Place crankshaft gear (2) with wear sleeve (4) in a suitable vice. Remove wear sleeve (4)
with a suitable chisel.
Sun Nov 17 23:42:39 UTC+0800 2019
2/2
2019/11/17

Shutdown SIS
Previous Screen
i05242547
Crankshaft Rear Seal and Wear Sleeve - Install - Includes
Crankshaft Gear
SMCS - 1161-012; 7558-012
Table 1
Required Tools
A
390-1146 Crankshaft Rear Seal and Wear Sleeve Driver(1)
1
423-9665 Crank shaft Rear Seal and Wear Sleeve Driver(2)
1
(1)
Used for the C3.3B
(2)
Used for the C2.6
Values.
1/2
2019/11/17

1. Place wear sleeve (4) on crankshaft gear (2). Position Tooling (A). Use a suitable press and
install wear sleeve (4).
2. Align crankshaft gear (2) with camshaft gear (3). Install crankshaft gear (2) into the
flywheel housing.
3. Apply clean engine oil on the lip of crankshaft rear seal (1). Use Tooling (A) in order to
install crankshaft rear seal (1).
End By:
a. Install the flywheel.
Sun Nov 17 23:43:38 UTC+0800 2019
2/2
2019/11/17

Shutdown SIS
Previous Screen
i05242551
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
A -
Guide Stud
M12 x 1.25 by 100 mm
2
B 138-7575 Link Brackets 2
Start By:
a. Remove the flywheel.
b. Remove the rear crankshaft seal.
Values.
NOTICE
1/3
2019/11/17

1. Remove two bolts (3) from flywheel housing (1).
2. Install Tooling (A) into flywheel housing (1).
3. Install Tooling (B). Install a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb).
4. Remove remaining six bolts (3) and 8 bolts (2) from flywheel housing (1).
5. Remove flywheel housing (1) from the cylinder block.
6. Remove bearing (4).
7. Remove the gasket (5).
8. If necessary, remove the dowels from the cylinder block.
1. Install flywheel housing (1) in the reverse order of removal.
2/3
2019/11/17

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

a. Install liquid gasket to the seam between the lower crankcase section (7) and the
upper crankcase section (6).
b. For the C3.3B tighten 8 bolts (3) and 8 bolts (2) to a torque of 103 to 117 N·m
(76 to 87 lb ft).
c. For the C2.6 tighten 8 bolts (3) and 8 bolts (2) to a torque of 78 to 90 N·m
(58 to 66 lb ft).
Sun Nov 17 23:44:38 UTC+0800 2019
3/3
2019/11/17

Shutdown SIS
Previous Screen
i05242553
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the v-belt.
Values.
NOTICE
1/2
2019/11/17

Caterpillar Cat 262D Skid Steer Loader (Prefix KTS) Service Repair Manual (KTS00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 262D Skid Steer Loader (Prefix KTS) Service Repair Manual (KTS00001 and up).pdf (15)

More from fuskddmmd (20)

Recently uploaded (20)

Caterpillar Cat 262D Skid Steer Loader (Prefix KTS) Service Repair Manual (KTS00001 and up).pdf