Caterpillar cat 305.5 e mini hydraulic excavator (prefix mx5) service repair manual (mx500001 and up)

Service Repair Manual
Models
305.5E Mini Hydraulic Excavator

Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 305.5E MINI HYD EXCAVATOR MX5
Configuration: 305.5E Mini Hydraulic Excavator MX500001-UP (MACHINE) POWERED BY C2.4 Engine
Disassembly and Assembly
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built
Machines
Media Number -UENR0128-11 Publication Date -01/08/2015 Date Updated -09/06/2016
i05243489
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 387-1352 Wear Sleeve Installer and Guide 1
B 1P-0520 Driver 1
C - Loctite 17430 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3305.5E Mini Hydraulic Excavator MX500001-UP (MACHINE) POWERED BY C2.4 ...
2020/2/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g02718716
1. Position wear sleeve (4) on Tooling (A). Ensure that the crankshaft flange is clean, dry, and
free from damage.
2. Apply Tooling (C) and use Tooling (A) to install the wear sleeve.

Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear
seal must be installed dry. Lubricate the inner rubber portion of the crankshaft rear seal.
3. Use Tooling (B) to install a new crankshaft rear seal (3) in bearing case cover (1).
4. Position the gaskets and bearing case cover (1) and install bolts (2). Position bearing case
cover (1) with marking UP upward.
5. Apply engine oil to bolts (2).
6. Tighten bolts (2) to a torque of 24 to 27 N·m (18 to 20 lb ft). Tighten bolts (2) with an equal
force on diagonal line.
End By:
a. Install the flywheel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Feb 11 15:26:32 UTC+0800 2020

Shutdown SIS
Previous Screen
Machines
i05243491
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
A -
Guide Stud
M10 by 100 mm
2
Start By:
a. Remove the flywheel.
NOTICE

1. Remove two bolts (2) from flywheel housing (1).
2. Install Tooling (A) into flywheel housing (1).
3. Install a suitable lifting device to flywheel housing (1). The weight of flywheel housing (1)
is approximately 40 kg (88 lb).
4. Remove remaining 11 bolts (2) and from flywheel housing (1).
5. Remove flywheel housing (1) from the cylinder block.
6. Remove the gasket.
7. If necessary, remove the dowels from the cylinder block.
Table 2
Required Tools
A -
Guide Stud
M10 by 100 mm
2
NOTICE

1. Ensure that the flywheel housing is clean and free from damage. If necessary, replace the
flywheel housing.
2. Inspect the crankshaft rear seal for leaks. If there are any oil leaks, replace the crankshaft
rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer
to Disassembly and Assembly, "Crankshaft Rear Seal - Install" for the correct procedure.
3. Clean the rear face of the cylinder block. If necessary, install the dowels into the cylinder
block.
4. Install Tooling (A) to the cylinder block.
5. Install the gasket.
6. Install a suitable lifting device to flywheel housing (1). The weight of flywheel housing (1)
is approximately 40 kg (88 lb).
7. Use the lifting device to align flywheel housing (1) with Tooling (A). Install flywheel
housing (1) to the cylinder block.
8. Install 11 bolts (2).
9. Remove Tooling (A). Install remaining two bolts (2).
10. Check the alignment of flywheel housing (1) with the crankshaft. Refer to System
Operation, Testing and Adjusting, "Flywheel Housing - Inspect" for the correct procedure.
End By:
a. Install the flywheel.
Tue Feb 11 15:27:29 UTC+0800 2020

Shutdown SIS
Previous Screen
Machines
i05243492
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
A 1P-2321 Puller As. 1
Start By:
a. Remove the alternator belt.
NOTICE

1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove nut (2) in order
to remove crankshaft pulley (1).
2. Position Tooling (A). Remove crankshaft pulley (1) from the crankshaft.
1. Install crankshaft pulley (1) in the reverse order of removal.
1. Tighten nut (2) to a torque of 138 - 156 N·m (102 - 115 lb ft).
Tue Feb 11 15:28:26 UTC+0800 2020

Shutdown SIS
Previous Screen
Machines
i05243500
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Start By:
a. Remove the crankshaft pulley.
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.

1. Remove key (1) and sleeve (2) from the crankshaft.
2. Remove crankshaft front seal (3).
Tue Feb 11 15:29:23 UTC+0800 2020

Shutdown SIS
Previous Screen
Machines
i05243515
Crankshaft Front Seal - Install
SMCS - 1160-012
NOTICE
Note: The crankshaft front seal should be installed dry. Lubricate the inner rubber portion of the
crankshaft front seal.
1. Inspect the nose of the crankshaft for damage. Ensure that the crankshaft is clean and dry.

2. Position a new crankshaft front seal (3). Install crankshaft front seal (3).
3. Lubricate the inner rubber portion of the crankshaft front seal. Position sleeve (2) on the
crankshaft and install key (1).
End By:
a. Install the crankshaft pulley.
Tue Feb 11 15:30:19 UTC+0800 2020

Shutdown SIS
Previous Screen
Machines
i05243527
Idler Gear - Remove and Install
SMCS - 1206
Removal Procedure
Table 1
Required Tools
A 387-1314 Idler Gear Tool 1
Start By:
a. Remove the front housing.
NOTICE
NOTICE
containing fluids.

Alignment of timing marks

1. Ensure that Timing Marks (X) on the idler gear and the crankshaft gear are aligned. Refer to
Illustration 1.
2. Ensure that Timing Marks (Y) on the idler gear and the camshaft gear are aligned. Refer to
Illustration 2.
3. Ensure that Timing Marks (Z) on the idler gear and the fuel injection pump gear are aligned.
Refer to Illustration 3.
4. Remove retaining ring (2) and collar (3). Remove idler gear (1).
5. Remove idler gear (1) from the idler shaft.
6. Use Tooling (A) to remove idler gear bearing (4) from idler gear (1).

7. If necessary, follow Steps 7.a and 7.b in order to remove idler shaft (5).
a. Make a temporary mark on the cylinder block in order to show the position of the oil
hole.
b. Remove bolts (6) and the washers. Remove idler shaft (5) from the cylinder block.
1. Install idler gear (1) in the reverse order of removal.
a. Ensure that the gears, cylinder block surface, and idler gear (1) are clean and free
from wear or damage. If necessary, replace any components that are worn or
damaged.
b. Lubricate idler shaft (5) with clean engine oil.
c. Lubricate idler gear bearing surface (4) with clean engine oil.
d. Apply engine oil to bolts (6). Tighten bolts (6) to a torque of 24 to 27 N·m
(18.0 to 20.0 lb ft).
Tue Feb 11 15:31:16 UTC+0800 2020

Shutdown SIS
Previous Screen
Machines
i05243564
Housing (Front) - Remove
SMCS - 1151-011; 1162-011
Removal Procedure
Start By:
a. Remove the crankshaft front seal.
NOTICE
NOTICE
containing fluids.

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

1. Disconnect harness assembly (4) from shut off solenoid (3).
2. Remove nut (2). Remove shut off solenoid (3) and the O-ring seal from front housing (1).

3. Remove bolts (9) and remove oil fill cover (6) and the gasket.
4. Remove bolts (8) and the washers. Remove nuts (5) and the washers from governor control
cover (7).
5. Remove two springs (10) and remove governor control cover (7) and the gasket.
6. Remove 15 bolts (11) Marked X from front housing (1). Remove front housing (1) from the
cylinder block. Remove the gasket.
Tue Feb 11 15:32:13 UTC+0800 2020

Shutdown SIS
Previous Screen
Machines
i05243568
Housing (Front) - Install
SMCS - 1151-012; 1162-012
Table 1
Required Tools
A 4C-5592 Thread Lubricant 1
NOTICE
1. Ensure that the front housing is clean and free from damage. If necessary, replace the front
housing.
2. Clean all the gasket surfaces of the cylinder block.

Caterpillar cat 305.5 e mini hydraulic excavator (prefix mx5) service repair manual (mx500001 and up)

More Related Content

What's hot (12)

Similar to Caterpillar cat 305.5 e mini hydraulic excavator (prefix mx5) service repair manual (mx500001 and up) (16)

More from fujsjefskekm (20)

Recently uploaded (20)

Caterpillar cat 305.5 e mini hydraulic excavator (prefix mx5) service repair manual (mx500001 and up)