Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Manual (TAZ00001 and up).pdf

Service Repair Manual
Models
308E Mini Hydraulic Excavator

Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242540
Crankshaft Rear Seal and Wear Sleeve - Remove - Includes
Crankshaft Gear
SMCS - 1161-011; 7558-011
Removal Procedure
Start By:
a. Remove the flywheel.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Place the engine at top dead center.
1/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g02799897
2. Use a screw driver to remove rear seal (1).
3. Check the alignment of crankshaft gear (2) and camshaft gear (3). Remove crankshaft gear
(2) and ring seal.
4. Place crankshaft gear (2) with wear sleeve (4) in a suitable vice. Remove wear sleeve (4)
with a suitable chisel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:04:48 UTC+0800 2020
2/2
2020/1/15

https://www.aservicemanualpdf.com/
My Dear Friend! Thank you very
much for visiting. Full manual if
required, please enter the
following URL into your browser.
https://www.aservicemanualpdf.com/

Shutdown SIS
Previous Screen
i05242547
Crankshaft Rear Seal and Wear Sleeve - Install - Includes
Crankshaft Gear
SMCS - 1161-012; 7558-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
390-1146 Crankshaft Rear Seal and Wear Sleeve Driver(1)
1
423-9665 Crank shaft Rear Seal and Wear Sleeve Driver(2)
1
(1)
Used for the C3.3B
(2)
Used for the C2.6
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1/2
2020/1/15

1. Place wear sleeve (4) on crankshaft gear (2). Position Tooling (A). Use a suitable press and
install wear sleeve (4).
2. Align crankshaft gear (2) with camshaft gear (3). Install crankshaft gear (2) into the
flywheel housing.
3. Apply clean engine oil on the lip of crankshaft rear seal (1). Use Tooling (A) in order to
install crankshaft rear seal (1).
End By:
a. Install the flywheel.
Wed Jan 15 17:05:44 UTC+0800 2020
2/2
2020/1/15

Shutdown SIS
Previous Screen
i05242551
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
A -
Guide Stud
M12 x 1.25 by 100 mm
2
B 138-7575 Link Brackets 2
Start By:
a. Remove the flywheel.
b. Remove the rear crankshaft seal.
Values.
NOTICE
1/3
2020/1/15

1. Remove two bolts (3) from flywheel housing (1).
2. Install Tooling (A) into flywheel housing (1).
3. Install Tooling (B). Install a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb).
4. Remove remaining six bolts (3) and 8 bolts (2) from flywheel housing (1).
5. Remove flywheel housing (1) from the cylinder block.
6. Remove bearing (4).
7. Remove the gasket (5).
8. If necessary, remove the dowels from the cylinder block.
1. Install flywheel housing (1) in the reverse order of removal.
2/3
2020/1/15

a. Install liquid gasket to the seam between the lower crankcase section (7) and the
upper crankcase section (6).
b. For the C3.3B tighten 8 bolts (3) and 8 bolts (2) to a torque of 103 to 117 N·m
(76 to 87 lb ft).
c. For the C2.6 tighten 8 bolts (3) and 8 bolts (2) to a torque of 78 to 90 N·m
(58 to 66 lb ft).
Wed Jan 15 17:06:41 UTC+0800 2020
3/3
2020/1/15

Shutdown SIS
Previous Screen
i05242553
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the v-belt.
Values.
NOTICE
1/2
2020/1/15

1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolt (2) in order
to remove crankshaft pulley (1).
1. Install crankshaft pulley (1) in the reverse order of removal.
a. Apply clean engine oil to the threads of bolt (2). Tighten bolt (2) to a torque of
255 to 274 N·m (188 to 202 lb ft).
Wed Jan 15 17:07:38 UTC+0800 2020
2/2
2020/1/15

Shutdown SIS
Previous Screen
i05242559
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Start By:
a. Remove the crankshaft pulley.
Values.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/3
2020/1/15

1. Use a suitable pry bar to remove crankshaft front seal (1).
Table 1
Required Tools
A 390-1140 Driver 1
B 6V-6640 Sealant 1
Note: The crankshaft front seal should be installed dry. Lubricate the inner rubber portion of the
crankshaft front seal.
2/3
2020/1/15

1. Lubricate the inner rubber portion of crankshaft front seal (1). Apply Tooling (B) on
crankshaft front seal (1). Position crankshaft front seal (1) on Tooling (A). Install crankshaft
front seal (1) on the crankshaft.
End By:
a. Install the crankshaft pulley.
Wed Jan 15 17:08:35 UTC+0800 2020
3/3
2020/1/15

Values.
NOTICE
NOTICE
containing fluids.
3/5
2020/1/15

Alignment of timing marks
1. Ensure that Timing Marks (X) on the camshaft gear and the crankshaft gear are aligned.
Refer to Illustration 1.
2. Ensure that Timing Marks (Y) on the idler gear and the camshaft gear are aligned. Refer to
Illustration 2.
3. Ensure that Timing Marks (Z) on the idler gear and the fuel injection pump gear are aligned.
Refer to Illustration 3.
4/5
2020/1/15

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

4. Remove bolts (2), washer (3), and the idler shaft from idler gear (1). Remove idler gear (1)
and the washer.
5. Use Tooling (A) to remove idler gear bearing (4) from idler gear (1).
1. Install idler gear (1) in the reverse order of removal.
2. Tighten bolts (2) to a torque of 30 to 34 N·m (22 to 25 lb ft).
a. Ensure that the gears, cylinder block surface, and idler gear (1) are clean and free
from wear or damage. If necessary, replace any components that are worn or
damaged.
b. Lubricate idler gear bearing surface (4) with clean engine oil.
c. Check oil clearance between the idler gear shaft and the idler gear bushing.
d. Check the idler gear shaft outer diameter and the inner diameter for the idler gear
bushing.
Wed Jan 15 17:09:32 UTC+0800 2020
5/5
2020/1/15

NOTICE
containing fluids.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
2. Disconnect hose assemblies (1) and (2) from the oil cooler.
3. Remove bolts (4).
3/5
2020/1/15

4. Remove front housing (3) and the gasket.
NOTICE
1. Ensure that the front housing is clean and free from damage. If necessary, replace the front
housing.
2. Clean all the gasket surfaces of the cylinder block.
3. Apply liquid gasket to the seam between the lower crankcase section (6) and the upper
crankcase section (5).
4/5
2020/1/15

4. Align a new gasket and install the gasket to the cylinder block.
5. Tighten 13 bolts (4) in a side to side sequence. Tighten bolts (4) to a torque of 24 to 27 N·m
(18 to 20 lb ft)
6. Connect hose assemblies (1) and (2) to the oil cooler.
End By:
a. Install the crankshaft front seal.
b. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling
System Coolant - Fill" for the correct procedure.
Wed Jan 15 17:10:28 UTC+0800 2020
5/5
2020/1/15

Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Manual (TAZ00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Manual (TAZ00001 and up).pdf (20)

More from hvy7sbkw8e (20)

Recently uploaded (20)

Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Manual (TAZ00001 and up).pdf