Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 and up)

Service Repair Manual
Models
311C and 311C U Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311C EXCAVATOR CKE
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01150941
Inlet and Exhaust Valve Seals - Remove and Install
SMCS - 1104-010-SA
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-1720 Seal Pick 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3...
2020/11/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g00610601
1. Use Tool (A) to remove valve stem seal (1) from the inlet and exhaust valve guide.
Illustration 1 shows the removal of the valve stem seal, when the valve guide (2) is removed
from cylinder head (4) .
Illustration 2 shows the removal of the valve stem seal, while the valve guide (2) is installed
in cylinder head (4) .
Installation Procedure
Table 2
Required Tools
A 5P-1720 Seal Pick 1
NOTICE
2/4
2020/11/10

Note: Do not apply any oil or sealant to the mating surface of the valve seal that comes into
contact with the valve guide. When the valve seal is installed, coat the surface of the valve stem
with engine oil in order to ensure initial lubrication of the seal lip.
1. Place the new valve stem seal in position on the valve guide.
2. Use Tool (A) to assist in installing the new valve stem seal.
Illustration 3 shows the installation of the valve stem seal, when the valve guide (2) is
removed from the cylinder head (4) .
Illustration 4 shows the installation of the valve stem seal, while the valve guide (2) is
installed in the cylinder head (4) .
Note: After the valve stem seal is installed on the valve guide, ensure that the seal is
properly installed in the groove of the valve guide.
3/4
2020/11/10

End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 10 22:19:02 UTC+0800 2020
4/4
2020/11/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01565892
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
A 185-3630 Strap Wrench Assembly 1
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
NOTICE
NOTICE
1/3
2020/11/10

Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Use Tool (A) and remove oil filter (2) from engine oil filter base (3) .
2. Remove the bolts (1) and washers from the engine oil filter base (3) .
3. Remove engine oil filter base (3) from the engine.
2/3
2020/11/10

4. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are
worn or damaged.
5. If necessary, remove eight bolts (6) and the washers in order to remove plate (5) from the
engine.
6. Check the condition of gasket (not shown). Replace the gasket, if the gasket is worn or
damaged.
7. Check engine oil filter base (3) and plate (5) for clogging and cracks. Replace damaged
components with replacement parts.
Tue Nov 10 22:19:58 UTC+0800 2020
3/3
2020/11/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01565969
Engine Oil Filter Base - Install
SMCS - 1306-012
NOTICE
1. Secure gasket and plate (5) to the cylinder block with eight bolts (6) .
1/2
2020/11/10

2. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are
damaged.
Note: Coat all of the O-ring seals with clean engine oil prior to installation.
3. Install the O-ring seals (4) on engine oil filter base (3) .
4. Secure engine oil filter base (3) to the plate (5) with four bolts (1) and the washers.
5. Install the engine oil filter (2) to the engine oil filter base (3) .
Note: Follow the installation procedure on the engine oil filter in order to install the engine
oil filter on the engine oil filter base.
Tue Nov 10 22:20:54 UTC+0800 2020
2/2
2020/11/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01615275
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
NOTICE
containing fluids.
1/2
2020/11/10

1. If necessary, remove bolt (1) and the washer from the cylinder head.
2. Remove oil tube assembly (dipstick) (2) from the cylinder block.
3. Check O-ring seal (3) (not shown) for wear or damage. Replace the O-ring seal, if the O-
ring seal is worn or damaged.
4. Remove bolts (4) and the washers that secure the oil cooler to the engine cylinder block.
The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16 bolts and washers.
5. Remove engine oil cooler (5) and gasket (6) (not shown) from the engine cylinder block.
Check the gasket for wear or damage. Replace the gasket, if the gasket is worn or damaged.
Note: Check the oil cooler cover for cracks. Replace the cover, if the cover is cracked.
Tue Nov 10 22:21:49 UTC+0800 2020
2/2
2020/11/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01152039
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
A. Remove the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
NOTICE
containing fluids.
1/3
2020/11/10

1. Remove four nuts (1) and the washers from the oil cooler core (3) .
2. Remove oil cooler core (3) from oil cooler cover (2) .
Note: Check the engine oil cooler core for cracks, clogging, and ruptures.
3. Remove two gaskets (4) from the oil cooler core. Check the gasket for wear or damage.
Replace the gaskets, if necessary.
2/3
2020/11/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01152137
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
1/2
2020/11/10

1. Install two gaskets (4) onto the oil cooler core (3) .
2. Install the oil cooler cover (2) onto the oil cooler core (3) .
3. Install four nuts (1) and the washers, which secure the oil cooler core to the oil cooler cover.
4. Tighten the four nuts (1) .
End By: Install the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Tue Nov 10 22:23:41 UTC+0800 2020
2/2
2020/11/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01615279
Engine Oil Cooler - Install
SMCS - 1378-012
NOTICE
1. Install engine oil cooler (5) and new gasket (6) (not shown). Ensure that all mating surfaces
are clean. Install bolts (4) and washers in order to secure the engine oil cooler to the engine
cylinder block. The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16
bolts and washers.
1/2
2020/11/10

2. Install oil tube assembly (dipstick) (2) into the cylinder block.
Note: Apply clean engine oil to the O-ring seal (3) (not shown) before installation.
3. Install bolt (1) and the washer into the cylinder head.
End By: Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Install".
Tue Nov 10 22:24:37 UTC+0800 2020
2/2
2020/11/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01615285
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
NOTICE
1/3
2020/11/10

1. Remove threaded plug (1) and the shim (2) for the engine oil relief valve from the right side
of the cylinder block.
2. Remove the spring (3) and spring seat (4) from the cylinder block.
Note: Check the spring seat (4) and the valve seat for an abnormal contact pattern. Inspect the
spring (3) for weakness or damage. If necessary, replace the engine oil relief valve with a new
part.
Note: Check the cylinder block for oil passages that are clogged.
NOTICE
2/3
2020/11/10

1. Install spring seat (4) and spring (3) in the cylinder block.
2. Install shim (2) and threaded plug (1) in the cylinder block.
3. Tighten threaded plug (1) of the engine oil relief valve to a torque of 49 ± 5 N·m (36 ± 4 lb
ft).
Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the
relief valve is 343 ± 20 kPa (50 ± 3 psi). Make adjustments by shimming, if necessary.
For more information, refer to Specifications, "Engine Oil Relief Valve".
Tue Nov 10 22:25:33 UTC+0800 2020
3/3
2020/11/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01615293
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
1/3
2020/11/10

1. Remove threaded plug (1) for the engine oil bypass valve from the cylinder block (2) .
2. Remove shim (3) from the cylinder block (2) .
3. Remove spring (4) from the cylinder block (2) .
4. Remove spring seat (5) from the cylinder block (2) .
Note: Check the spring seat (5) and the valve seat for an abnormal contact pattern. Inspect the
spring (4) for weakness or damage. If necessary, replace the engine oil bypass valve with a new
part.
Note: Check the cylinder block (2) for oil passages that are clogged.
NOTICE
2/3
2020/11/10

1. Install spring seat (5) (not shown) and spring (4) in the cylinder block (2) .
2. Install shim (3) and threaded plug (1) in the cylinder block (2) .
3. Tighten the threaded plug (1) to a torque of 69 ± 5 N·m (51 ± 4 lb ft).
Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the
relief valve is 981 ± 98 kPa (142 ± 14 psi). Make adjustments by shimming, if necessary.
For information on testing the engine oil relief valve, refer to Testing and Adjusting, "Lubrication
System".
For more information, refer to Specifications, "Engine Oil Bypass Valve".
End By: Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove and Install".
Tue Nov 10 22:26:28 UTC+0800 2020
3/3
2020/11/10

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01146335
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
NOTICE
1/5
2020/11/10

Thank you very much
for your reading.
Please click here to buy
After you pay.
Then, you can
download the complete
manual instantly.
No waiting.

containing fluids.
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolt (1) from the cover (2) .
2. Remove cover (2) for the engine oil pump from the front housing. Check gasket (3) (not
shown) for damage or wear. Replace the gasket, if the gasket is worn or damaged.
2/5
2020/11/10

3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
4. Position the front housing on a work bench in order to remove the oil pump gear from the
rear of the housing.
5. Use Tool (A) to remove oil pump gear (6) from the front housing.
6. Position the front housing on a work bench in order to remove the drive gear from the front
of the housing.
7. Remove drive gear (7) from the front housing.
3/5
2020/11/10

Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 and up)

More Related Content

Similar to Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 and up) (20)

More from fjsjekdmmeme (20)

Recently uploaded (20)

Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 and up)