SlideShare a Scribd company logo

Caterpillar Cat 311C and 311C U Excavator (Prefix CKE) Service Repair Manual Instant Download.pdf

Y
yan77xunhao

The document provides instructions for removing and installing valve stem seals, the engine oil filter base, and the engine oil cooler on Caterpillar 3064 and 3066 engines. The procedures include using appropriate tools to remove old parts and install new parts, checking components for wear or damage, and ensuring that fluids are contained properly. Precautions are listed to keep parts clean and prevent contamination.

Automotive
1 of 28
Download to read offline
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Service Repair Manual Models 311C and 311C U Excavator
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01150941 Inlet and Exhaust Valve Seals - Remove and Install SMCS - 1104-010-SA Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5P-1720 Seal Pick 1 Start By: A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/4 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g00610601 Illustration 2 g00610605 1. Use Tool (A) to remove valve stem seal (1) from the inlet and exhaust valve guide. Illustration 1 shows the removal of the valve stem seal, when the valve guide (2) is removed from cylinder head (4) . Illustration 2 shows the removal of the valve stem seal, while the valve guide (2) is installed in cylinder head (4) . Installation Procedure Table 2 Required Tools Tool Part Number Part Description Qty A 5P-1720 Seal Pick 1 NOTICE Keep all parts clean from contaminants. 2/4 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Contaminants may cause rapid wear and shortened component life. Note: Do not apply any oil or sealant to the mating surface of the valve seal that comes into contact with the valve guide. When the valve seal is installed, coat the surface of the valve stem with engine oil in order to ensure initial lubrication of the seal lip. Illustration 3 g00610601 Illustration 4 g00610605 1. Place the new valve stem seal in position on the valve guide. 2. Use Tool (A) to assist in installing the new valve stem seal. Illustration 3 shows the installation of the valve stem seal, when the valve guide (2) is removed from the cylinder head (4) . Illustration 4 shows the installation of the valve stem seal, while the valve guide (2) is installed in the cylinder head (4) . Note: After the valve stem seal is installed on the valve guide, ensure that the seal is properly installed in the groove of the valve guide. 3/4 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:19:02 UTC+0800 2020 4/4 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01565892 Engine Oil Filter Base - Remove SMCS - 1306-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 185-3630 Strap Wrench Assembly 1 Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE 1/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00813775 Illustration 2 g00813789 1. Use Tool (A) and remove oil filter (2) from engine oil filter base (3) . 2. Remove the bolts (1) and washers from the engine oil filter base (3) . 3. Remove engine oil filter base (3) from the engine. 2/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are worn or damaged. Illustration 3 g00813823 5. If necessary, remove eight bolts (6) and the washers in order to remove plate (5) from the engine. 6. Check the condition of gasket (not shown). Replace the gasket, if the gasket is worn or damaged. 7. Check engine oil filter base (3) and plate (5) for clogging and cracks. Replace damaged components with replacement parts. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:19:58 UTC+0800 2020 3/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01565969 Engine Oil Filter Base - Install SMCS - 1306-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00813823 1. Secure gasket and plate (5) to the cylinder block with eight bolts (6) . 1/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 2 g00813789 2. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are damaged. Note: Coat all of the O-ring seals with clean engine oil prior to installation. 3. Install the O-ring seals (4) on engine oil filter base (3) . Illustration 3 g00813775 4. Secure engine oil filter base (3) to the plate (5) with four bolts (1) and the washers. 5. Install the engine oil filter (2) to the engine oil filter base (3) . Note: Follow the installation procedure on the engine oil filter in order to install the engine oil filter on the engine oil filter base. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:20:54 UTC+0800 2020 2/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01615275 Engine Oil Cooler - Remove SMCS - 1378-011 Removal Procedure Start By: A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g00611319 1. If necessary, remove bolt (1) and the washer from the cylinder head. 2. Remove oil tube assembly (dipstick) (2) from the cylinder block. 3. Check O-ring seal (3) (not shown) for wear or damage. Replace the O-ring seal, if the O- ring seal is worn or damaged. Illustration 2 g00611320 4. Remove bolts (4) and the washers that secure the oil cooler to the engine cylinder block. The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16 bolts and washers. 5. Remove engine oil cooler (5) and gasket (6) (not shown) from the engine cylinder block. Check the gasket for wear or damage. Replace the gasket, if the gasket is worn or damaged. Note: Check the oil cooler cover for cracks. Replace the cover, if the cover is cracked. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:21:49 UTC+0800 2020 2/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01152039 Engine Oil Cooler - Disassemble SMCS - 1378-015 Disassembly Procedure Start By: A. Remove the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g00618921 Illustration 2 g00611507 1. Remove four nuts (1) and the washers from the oil cooler core (3) . 2. Remove oil cooler core (3) from oil cooler cover (2) . Note: Check the engine oil cooler core for cracks, clogging, and ruptures. 3. Remove two gaskets (4) from the oil cooler core. Check the gasket for wear or damage. Replace the gaskets, if necessary. 2/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01152137 Engine Oil Cooler - Assemble SMCS - 1378-016 Assembly Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 1 g00618921 Illustration 2 g00611507 1. Install two gaskets (4) onto the oil cooler core (3) . 2. Install the oil cooler cover (2) onto the oil cooler core (3) . 3. Install four nuts (1) and the washers, which secure the oil cooler core to the oil cooler cover. 4. Tighten the four nuts (1) . End By: Install the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:23:41 UTC+0800 2020 2/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01615279 Engine Oil Cooler - Install SMCS - 1378-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00611320 1. Install engine oil cooler (5) and new gasket (6) (not shown). Ensure that all mating surfaces are clean. Install bolts (4) and washers in order to secure the engine oil cooler to the engine cylinder block. The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16 bolts and washers. 1/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 2 g00611319 2. Install oil tube assembly (dipstick) (2) into the cylinder block. Note: Apply clean engine oil to the O-ring seal (3) (not shown) before installation. 3. Install bolt (1) and the washer into the cylinder head. End By: Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:24:37 UTC+0800 2020 2/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01615285 Engine Oil Relief Valve - Remove and Install SMCS - 1315-010 Removal Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00607236 1/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 2 g00607247 1. Remove threaded plug (1) and the shim (2) for the engine oil relief valve from the right side of the cylinder block. 2. Remove the spring (3) and spring seat (4) from the cylinder block. Note: Check the spring seat (4) and the valve seat for an abnormal contact pattern. Inspect the spring (3) for weakness or damage. If necessary, replace the engine oil relief valve with a new part. Note: Check the cylinder block for oil passages that are clogged. Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 2/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 3 g00607247 Illustration 4 g00607236 1. Install spring seat (4) and spring (3) in the cylinder block. 2. Install shim (2) and threaded plug (1) in the cylinder block. 3. Tighten threaded plug (1) of the engine oil relief valve to a torque of 49 ± 5 N·m (36 ± 4 lb ft). Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the relief valve is 343 ± 20 kPa (50 ± 3 psi). Make adjustments by shimming, if necessary. For more information, refer to Specifications, "Engine Oil Relief Valve". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:25:33 UTC+0800 2020 3/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01615293 Engine Oil Bypass Valve - Remove and Install SMCS - 1306-010-BV Removal Procedure Start By: A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00607679 1/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 2 g00607688 1. Remove threaded plug (1) for the engine oil bypass valve from the cylinder block (2) . 2. Remove shim (3) from the cylinder block (2) . 3. Remove spring (4) from the cylinder block (2) . 4. Remove spring seat (5) from the cylinder block (2) . Note: Check the spring seat (5) and the valve seat for an abnormal contact pattern. Inspect the spring (4) for weakness or damage. If necessary, replace the engine oil bypass valve with a new part. Note: Check the cylinder block (2) for oil passages that are clogged. Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 2/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Illustration 3 g00607688 Illustration 4 g00607679 1. Install spring seat (5) (not shown) and spring (4) in the cylinder block (2) . 2. Install shim (3) and threaded plug (1) in the cylinder block (2) . 3. Tighten the threaded plug (1) to a torque of 69 ± 5 N·m (51 ± 4 lb ft). Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the relief valve is 981 ± 98 kPa (142 ± 14 psi). Make adjustments by shimming, if necessary. For information on testing the engine oil relief valve, refer to Testing and Adjusting, "Lubrication System". For more information, refer to Specifications, "Engine Oil Bypass Valve". End By: Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:26:28 UTC+0800 2020 3/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01146335 Engine Oil Pump - Remove SMCS - 1304-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1P-2320 Combination Puller 1 B 1P-0510 Driver Group 1 Start By: A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers 1/5 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00607826 Note: Illustration 1 does not show that the front housing is removed from the cylinder block. 1. Remove bolt (1) from the cover (2) . 2. Remove cover (2) for the engine oil pump from the front housing. Check gasket (3) (not shown) for damage or wear. Replace the gasket, if the gasket is worn or damaged. Illustration 2 g00607770 2/5 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading
3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5) (slip fit). Illustration 3 g00607857 4. Position the front housing on a work bench in order to remove the oil pump gear from the rear of the housing. 5. Use Tool (A) to remove oil pump gear (6) from the front housing. Illustration 4 g00607885 6. Position the front housing on a work bench in order to remove the drive gear from the front of the housing. 7. Remove drive gear (7) from the front housing. 3/5 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

More Related Content

PDF
Caterpillar Cat 311C Excavator (Prefix CKE) Service Repair Manual (CKE00001 a...
lituo39419496
 
PDF
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...
lituo39419496
 
PDF
Caterpillar Cat 311C Excavator (Prefix CKE) Service Repair Manual (CKE00001 a...
tuzhiyou2
 
PDF
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...
tuzhiyou2
 
PDF
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...
qfyc504378
 
PDF
Caterpillar Cat 311C Excavator (Prefix CKE) Service Repair Manual (CKE00001 a...
qfyc504378
 
PDF
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual Instant D...
nu174136zhao
 
PDF
Caterpillar Cat 311C Excavator (Prefix CKE) Service Repair Manual Instant Dow...
yongmxy723
 
Caterpillar Cat 311C Excavator (Prefix CKE) Service Repair Manual (CKE00001 a...
lituo39419496
 
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...
lituo39419496
 
Caterpillar Cat 311C Excavator (Prefix CKE) Service Repair Manual (CKE00001 a...
tuzhiyou2
 
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...
tuzhiyou2
 
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual (CKE00001...
qfyc504378
 
Caterpillar Cat 311C Excavator (Prefix CKE) Service Repair Manual (CKE00001 a...
qfyc504378
 
Caterpillar Cat 311C U Excavator (Prefix CKE) Service Repair Manual Instant D...
nu174136zhao
 
Caterpillar Cat 311C Excavator (Prefix CKE) Service Repair Manual Instant Dow...
yongmxy723
 

More from yan77xunhao (20)

PDF
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...
yan77xunhao
 
PDF
Caterpillar Cat 416E BACKHOE LOADER (Prefix SHA) Service Repair Manual Instan...
yan77xunhao
 
PDF
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdf
yan77xunhao
 
PDF
Caterpillar Cat 434E BACKHOE LOADER (Prefix SJL) Service Repair Manual Instan...
yan77xunhao
 
PDF
Caterpillar Cat 420F BACKHOE LOADER (Prefix SKR) Service Repair Manual Instan...
yan77xunhao
 
PDF
Caterpillar Cat 428D BACKHOE LOADER (Prefix BNS) Service Repair Manual Instan...
yan77xunhao
 
PDF
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...
yan77xunhao
 
PDF
Caterpillar Cat 416F BACKHOE LOADER (Prefix LWT) Service Repair Manual Instan...
yan77xunhao
 
PDF
Caterpillar Cat 385B Excavator (Prefix MYA) Service Repair Manual Instant Dow...
yan77xunhao
 
PDF
Caterpillar Cat 385C and 385C L Excavator (Prefix JCM) Service Repair Manual ...
yan77xunhao
 
PDF
Caterpillar Cat 385B EXCAVATOR (Prefix BKX) Service Repair Manual Instant Dow...
yan77xunhao
 
PDF
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...
yan77xunhao
 
PDF
Caterpillar Cat 374F L Excavator (Prefix AP4) Service Repair Manual Instant D...
yan77xunhao
 
PDF
Caterpillar Cat 235C EXCAVATOR (Prefix 2PG) Service Repair Manual Instant Dow...
yan77xunhao
 
PDF
Caterpillar Cat 428D BACKHOE LOADER (Prefix BXC) Service Repair Manual Instan...
yan77xunhao
 
PDF
Caterpillar Cat 428D BACKHOE LOADER (Prefix BNS) Service Repair Manual Instan...
yan77xunhao
 
PDF
Caterpillar Cat 420E BACKHOE LOADER (Prefix KMW) Service Repair Manual Instan...
yan77xunhao
 
PDF
Caterpillar Cat 420E BACKHOE LOADER (Prefix HLS) Service Repair Manual Instan...
yan77xunhao
 
PDF
Caterpillar Cat 420E BACKHOE LOADER (Prefix PHC) Service Repair Manual Instan...
yan77xunhao
 
PDF
Caterpillar Cat 420E BACKHOE LOADER (Prefix PRA) Service Repair Manual Instan...
yan77xunhao
 
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...
yan77xunhao
 
Caterpillar Cat 416E BACKHOE LOADER (Prefix SHA) Service Repair Manual Instan...
yan77xunhao
 
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdf
yan77xunhao
 
Caterpillar Cat 434E BACKHOE LOADER (Prefix SJL) Service Repair Manual Instan...
yan77xunhao
 
Caterpillar Cat 420F BACKHOE LOADER (Prefix SKR) Service Repair Manual Instan...
yan77xunhao
 
Caterpillar Cat 428D BACKHOE LOADER (Prefix BNS) Service Repair Manual Instan...
yan77xunhao
 
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...
yan77xunhao
 
Caterpillar Cat 416F BACKHOE LOADER (Prefix LWT) Service Repair Manual Instan...
yan77xunhao
 
Caterpillar Cat 385B Excavator (Prefix MYA) Service Repair Manual Instant Dow...
yan77xunhao
 
Caterpillar Cat 385C and 385C L Excavator (Prefix JCM) Service Repair Manual ...
yan77xunhao
 
Caterpillar Cat 385B EXCAVATOR (Prefix BKX) Service Repair Manual Instant Dow...
yan77xunhao
 
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...
yan77xunhao
 
Caterpillar Cat 374F L Excavator (Prefix AP4) Service Repair Manual Instant D...
yan77xunhao
 
Caterpillar Cat 235C EXCAVATOR (Prefix 2PG) Service Repair Manual Instant Dow...
yan77xunhao
 
Caterpillar Cat 428D BACKHOE LOADER (Prefix BXC) Service Repair Manual Instan...
yan77xunhao
 
Caterpillar Cat 428D BACKHOE LOADER (Prefix BNS) Service Repair Manual Instan...
yan77xunhao
 
Caterpillar Cat 420E BACKHOE LOADER (Prefix KMW) Service Repair Manual Instan...
yan77xunhao
 
Caterpillar Cat 420E BACKHOE LOADER (Prefix HLS) Service Repair Manual Instan...
yan77xunhao
 
Caterpillar Cat 420E BACKHOE LOADER (Prefix PHC) Service Repair Manual Instan...
yan77xunhao
 
Caterpillar Cat 420E BACKHOE LOADER (Prefix PRA) Service Repair Manual Instan...
yan77xunhao
 

Recently uploaded (20)

PDF
Journal Meraj.pdfuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu
emonmian100
 
PPTX
Intro to ISO 9001 2015.pptx for awareness
nadianisar5
 
PPT
ACCOMPLISHMENT REPOERTS AND FILE OF GRADE 12 2021.ppt
cristinegraceacuyan1
 
PDF
Caterpillar Cat 315C Excavator (Prefix ANF) Service Repair Manual Instant Dow...
ovhzz53
 
PPTX
Independence_Day_Patriotic theme (1).pptx
deepupathakji
 
PPTX
Gayatri Cultural Educational Society.pptx
HardikShukl
 
PPTX
1. introduction-to-bvcjdhjdfffffffffffffffffffffffffffffffffffmicroprocessors...
eeshakhanzadi43
 
PPTX
Zeem: Transition Your Fleet, Seamlessly by Margaret Boelter
Forth
 
PPTX
Culture by Design.pptxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
ddwc381
 
PDF
Volvo EC290C NL EC290CNL Hydraulic Excavator Specs Manual.pdf
Service Repair Manual
 
PDF
Volvo EC20C Excavator Step-by-step Maintenance Instructions pdf
Service Repair Manual
 
PDF
Volvo EC290C NL EC290CNL engine Manual.pdf
Service Repair Manual
 
PDF
Caterpillar Cat 315C Excavator (Prefix CJC) Service Repair Manual Instant Dow...
ovics74
 
PPTX
Small Fleets, Big Change: Market Acceleration by Niki Okuk
Forth
 
PPTX
capstoneoooooooooooooooooooooooooooooooooo
InzamamUlHaque62
 
PPTX
Lecture 3b C Library xnxjxjxjxkx_ ESP32.pptx
indalrenu
 
PPTX
UNIT-2(B) Organisavtional Appraisal.pptx
chahalharry627
 
PDF
Volvo EC290C NL EC290CNL Excavator Service Repair Manual Instant Download.pdf
Service Repair Manual
 
PDF
computer system to create, modify, analyse or optimize an engineering design.
norazamaliman1
 
PDF
Volvo EC20C Excavator Service maintenance schedules.pdf
Service Repair Manual
 
Journal Meraj.pdfuuuuuuuuuuuuuuuuuuuuuuuuuuuuuuu
emonmian100
 
Intro to ISO 9001 2015.pptx for awareness
nadianisar5
 
ACCOMPLISHMENT REPOERTS AND FILE OF GRADE 12 2021.ppt
cristinegraceacuyan1
 
Caterpillar Cat 315C Excavator (Prefix ANF) Service Repair Manual Instant Dow...
ovhzz53
 
Independence_Day_Patriotic theme (1).pptx
deepupathakji
 
Gayatri Cultural Educational Society.pptx
HardikShukl
 
1. introduction-to-bvcjdhjdfffffffffffffffffffffffffffffffffffmicroprocessors...
eeshakhanzadi43
 
Zeem: Transition Your Fleet, Seamlessly by Margaret Boelter
Forth
 
Culture by Design.pptxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
ddwc381
 
Volvo EC290C NL EC290CNL Hydraulic Excavator Specs Manual.pdf
Service Repair Manual
 
Volvo EC20C Excavator Step-by-step Maintenance Instructions pdf
Service Repair Manual
 
Volvo EC290C NL EC290CNL engine Manual.pdf
Service Repair Manual
 
Caterpillar Cat 315C Excavator (Prefix CJC) Service Repair Manual Instant Dow...
ovics74
 
Small Fleets, Big Change: Market Acceleration by Niki Okuk
Forth
 
capstoneoooooooooooooooooooooooooooooooooo
InzamamUlHaque62
 
Lecture 3b C Library xnxjxjxjxkx_ ESP32.pptx
indalrenu
 
UNIT-2(B) Organisavtional Appraisal.pptx
chahalharry627
 
Volvo EC290C NL EC290CNL Excavator Service Repair Manual Instant Download.pdf
Service Repair Manual
 
computer system to create, modify, analyse or optimize an engineering design.
norazamaliman1
 
Volvo EC20C Excavator Service maintenance schedules.pdf
Service Repair Manual
 

Caterpillar Cat 311C and 311C U Excavator (Prefix CKE) Service Repair Manual Instant Download.pdf

  • 1. Service Repair Manual Models 311C and 311C U Excavator
  • 2. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01150941 Inlet and Exhaust Valve Seals - Remove and Install SMCS - 1104-010-SA Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5P-1720 Seal Pick 1 Start By: A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/4 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 3. Illustration 1 g00610601 Illustration 2 g00610605 1. Use Tool (A) to remove valve stem seal (1) from the inlet and exhaust valve guide. Illustration 1 shows the removal of the valve stem seal, when the valve guide (2) is removed from cylinder head (4) . Illustration 2 shows the removal of the valve stem seal, while the valve guide (2) is installed in cylinder head (4) . Installation Procedure Table 2 Required Tools Tool Part Number Part Description Qty A 5P-1720 Seal Pick 1 NOTICE Keep all parts clean from contaminants. 2/4 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 4. Contaminants may cause rapid wear and shortened component life. Note: Do not apply any oil or sealant to the mating surface of the valve seal that comes into contact with the valve guide. When the valve seal is installed, coat the surface of the valve stem with engine oil in order to ensure initial lubrication of the seal lip. Illustration 3 g00610601 Illustration 4 g00610605 1. Place the new valve stem seal in position on the valve guide. 2. Use Tool (A) to assist in installing the new valve stem seal. Illustration 3 shows the installation of the valve stem seal, when the valve guide (2) is removed from the cylinder head (4) . Illustration 4 shows the installation of the valve stem seal, while the valve guide (2) is installed in the cylinder head (4) . Note: After the valve stem seal is installed on the valve guide, ensure that the seal is properly installed in the groove of the valve guide. 3/4 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 5. End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:19:02 UTC+0800 2020 4/4 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 6. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01565892 Engine Oil Filter Base - Remove SMCS - 1306-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 185-3630 Strap Wrench Assembly 1 Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE 1/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 7. Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00813775 Illustration 2 g00813789 1. Use Tool (A) and remove oil filter (2) from engine oil filter base (3) . 2. Remove the bolts (1) and washers from the engine oil filter base (3) . 3. Remove engine oil filter base (3) from the engine. 2/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 8. 4. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are worn or damaged. Illustration 3 g00813823 5. If necessary, remove eight bolts (6) and the washers in order to remove plate (5) from the engine. 6. Check the condition of gasket (not shown). Replace the gasket, if the gasket is worn or damaged. 7. Check engine oil filter base (3) and plate (5) for clogging and cracks. Replace damaged components with replacement parts. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:19:58 UTC+0800 2020 3/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 9. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01565969 Engine Oil Filter Base - Install SMCS - 1306-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00813823 1. Secure gasket and plate (5) to the cylinder block with eight bolts (6) . 1/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 10. Illustration 2 g00813789 2. Check the condition of O-ring seals (4). Replace the O-ring seals, if the O-ring seals are damaged. Note: Coat all of the O-ring seals with clean engine oil prior to installation. 3. Install the O-ring seals (4) on engine oil filter base (3) . Illustration 3 g00813775 4. Secure engine oil filter base (3) to the plate (5) with four bolts (1) and the washers. 5. Install the engine oil filter (2) to the engine oil filter base (3) . Note: Follow the installation procedure on the engine oil filter in order to install the engine oil filter on the engine oil filter base. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:20:54 UTC+0800 2020 2/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 11. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01615275 Engine Oil Cooler - Remove SMCS - 1378-011 Removal Procedure Start By: A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 12. Illustration 1 g00611319 1. If necessary, remove bolt (1) and the washer from the cylinder head. 2. Remove oil tube assembly (dipstick) (2) from the cylinder block. 3. Check O-ring seal (3) (not shown) for wear or damage. Replace the O-ring seal, if the O- ring seal is worn or damaged. Illustration 2 g00611320 4. Remove bolts (4) and the washers that secure the oil cooler to the engine cylinder block. The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16 bolts and washers. 5. Remove engine oil cooler (5) and gasket (6) (not shown) from the engine cylinder block. Check the gasket for wear or damage. Replace the gasket, if the gasket is worn or damaged. Note: Check the oil cooler cover for cracks. Replace the cover, if the cover is cracked. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:21:49 UTC+0800 2020 2/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 13. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01152039 Engine Oil Cooler - Disassemble SMCS - 1378-015 Disassembly Procedure Start By: A. Remove the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 14. Illustration 1 g00618921 Illustration 2 g00611507 1. Remove four nuts (1) and the washers from the oil cooler core (3) . 2. Remove oil cooler core (3) from oil cooler cover (2) . Note: Check the engine oil cooler core for cracks, clogging, and ruptures. 3. Remove two gaskets (4) from the oil cooler core. Check the gasket for wear or damage. Replace the gaskets, if necessary. 2/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 15. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01152137 Engine Oil Cooler - Assemble SMCS - 1378-016 Assembly Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 16. Illustration 1 g00618921 Illustration 2 g00611507 1. Install two gaskets (4) onto the oil cooler core (3) . 2. Install the oil cooler cover (2) onto the oil cooler core (3) . 3. Install four nuts (1) and the washers, which secure the oil cooler core to the oil cooler cover. 4. Tighten the four nuts (1) . End By: Install the oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:23:41 UTC+0800 2020 2/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 17. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01615279 Engine Oil Cooler - Install SMCS - 1378-012 Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00611320 1. Install engine oil cooler (5) and new gasket (6) (not shown). Ensure that all mating surfaces are clean. Install bolts (4) and washers in order to secure the engine oil cooler to the engine cylinder block. The 3066 Engine has 24 bolts and washers while the 3064 Engine has 16 bolts and washers. 1/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 18. Illustration 2 g00611319 2. Install oil tube assembly (dipstick) (2) into the cylinder block. Note: Apply clean engine oil to the O-ring seal (3) (not shown) before installation. 3. Install bolt (1) and the washer into the cylinder head. End By: Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:24:37 UTC+0800 2020 2/2 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 19. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01615285 Engine Oil Relief Valve - Remove and Install SMCS - 1315-010 Removal Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00607236 1/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 20. Illustration 2 g00607247 1. Remove threaded plug (1) and the shim (2) for the engine oil relief valve from the right side of the cylinder block. 2. Remove the spring (3) and spring seat (4) from the cylinder block. Note: Check the spring seat (4) and the valve seat for an abnormal contact pattern. Inspect the spring (3) for weakness or damage. If necessary, replace the engine oil relief valve with a new part. Note: Check the cylinder block for oil passages that are clogged. Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 2/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 21. Illustration 3 g00607247 Illustration 4 g00607236 1. Install spring seat (4) and spring (3) in the cylinder block. 2. Install shim (2) and threaded plug (1) in the cylinder block. 3. Tighten threaded plug (1) of the engine oil relief valve to a torque of 49 ± 5 N·m (36 ± 4 lb ft). Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the relief valve is 343 ± 20 kPa (50 ± 3 psi). Make adjustments by shimming, if necessary. For more information, refer to Specifications, "Engine Oil Relief Valve". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:25:33 UTC+0800 2020 3/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 22. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01615293 Engine Oil Bypass Valve - Remove and Install SMCS - 1306-010-BV Removal Procedure Start By: A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g00607679 1/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 23. Illustration 2 g00607688 1. Remove threaded plug (1) for the engine oil bypass valve from the cylinder block (2) . 2. Remove shim (3) from the cylinder block (2) . 3. Remove spring (4) from the cylinder block (2) . 4. Remove spring seat (5) from the cylinder block (2) . Note: Check the spring seat (5) and the valve seat for an abnormal contact pattern. Inspect the spring (4) for weakness or damage. If necessary, replace the engine oil bypass valve with a new part. Note: Check the cylinder block (2) for oil passages that are clogged. Installation Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 2/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 24. Illustration 3 g00607688 Illustration 4 g00607679 1. Install spring seat (5) (not shown) and spring (4) in the cylinder block (2) . 2. Install shim (3) and threaded plug (1) in the cylinder block (2) . 3. Tighten the threaded plug (1) to a torque of 69 ± 5 N·m (51 ± 4 lb ft). Note: Test the opening pressure for the engine oil relief valve. The opening pressure for the relief valve is 981 ± 98 kPa (142 ± 14 psi). Make adjustments by shimming, if necessary. For information on testing the engine oil relief valve, refer to Testing and Adjusting, "Lubrication System". For more information, refer to Specifications, "Engine Oil Bypass Valve". End By: Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Tue Nov 10 22:26:28 UTC+0800 2020 3/3 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 25. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 311C EXCAVATOR CKE Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine Disassembly and Assembly 3064 and 3066 Engines for Caterpillar Built Machines Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012 i01146335 Engine Oil Pump - Remove SMCS - 1304-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1P-2320 Combination Puller 1 B 1P-0510 Driver Group 1 Start By: A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers 1/5 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 26. before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00607826 Note: Illustration 1 does not show that the front housing is removed from the cylinder block. 1. Remove bolt (1) from the cover (2) . 2. Remove cover (2) for the engine oil pump from the front housing. Check gasket (3) (not shown) for damage or wear. Replace the gasket, if the gasket is worn or damaged. Illustration 2 g00607770 2/5 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
  • 27. Suggest: If the above button click is invalid. Please download this document first, and then click the above link to download the complete manual. Thank you so much for reading
  • 28. 3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5) (slip fit). Illustration 3 g00607857 4. Position the front housing on a work bench in order to remove the oil pump gear from the rear of the housing. 5. Use Tool (A) to remove oil pump gear (6) from the front housing. Illustration 4 g00607885 6. Position the front housing on a work bench in order to remove the drive gear from the front of the housing. 7. Remove drive gear (7) from the front housing. 3/5 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine(SEBP3... 2020/11/10 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...