Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF00001 and up).pdf

Service Repair Manual
Models
312D2 and 312D2 L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D2 EXCAVATOR DGF
Configuration: 312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02298184
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Drain the coolant from the engine oil cooler into a suitable container for storage or disposal.
Drain the engine oil from the engine oil cooler into a suitable container. Refer to Operation
and Maintenance Manual for the procedure on draining the engine coolant and the engine
oil.
b. Remove the hose from the air filter to the integral air inlet. Refer to the OEM information
for further details.
c. Remove the fuel priming pump. Refer to this Disassembly and Assembly Manual, "Fuel
Priming Pump and Fuel Filter Base - Remove and Install".
d. Remove the pipe for the boost control.
e. Remove the fuel injectors. Refer to this Disassembly and Assembly Manual, "Fuel Injection
Nozzles - Remove".
f. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
g. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
h. Remove the glow plugs. Refer to this Disassembly and Assembly Manual, "Glow Plugs -
NOTICE
1/4
312D2 & 312D2 L Excavators DGF00001-UP (MACHINE) POWERED BY 3054C E...
2020/6/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Operation and Maintenance Manual, "Refill Capacities" for the coolant capacity
and the engine oil capacity of the engine.
Illustration 1 g00951472
1. Remove the setscrew (1) and the fuel line from the cylinder head.
2. Disconnect the harness assembly (4) from the coolant temperature sensor.
3. Disconnect tube assembly (5) from the cylinder head.
2/4
2020/6/20

4. Remove the setscrews (6). Remove the bypass tube (7) from the cylinder head. Remove the
O-ring seals from the bypass tube. Discard the O-ring seals.
5. Gradually loosen the setscrews (8) in reverse numerical order. Refer to Illustration 3. This
will help prevent distortion of the cylinder head.
6. Remove the setscrews (8) from the cylinder head (9).
7. Use a suitable lifting device and carefully lift the cylinder head off the cylinder block. The
weight of the cylinder head is approximately 57 kg (126 lb).
Note: Take care not to damage the machined surfaces of the cylinder head (9) during
removal.
3/4
2020/6/20

Note: Do not use a lever to separate the cylinder head from the cylinder block.
NOTICE
Place the cylinder head on a surface that will not scratch the face of the
cylinder head.
8. Remove the cylinder head gasket. Discard the cylinder head gasket.
Note: Note the location of the dowels on the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 20 23:00:09 UTC+0800 2020
4/4
2020/6/20

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02298802
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6238 Guide Bolt 2
B 8T-3052 Degree Wheel 1
C - Red Rubber Grease -
NOTICE
Note: Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure
that there is no debris in the cylinder bores, the coolant passages, and the lubricant passages.
Note: Thoroughly clean the hole in the cylinder head for the gas that is ventilated from the
crankcase. Ensure that the hole is not restricted by debris and/or oil deposits.
1/6
2020/6/20

1. Install the cylinder head gasket on the dowels (10) on top of the cylinder block.
Note: Do not use any sealant or compound on the cylinder head gasket.
2. Install the Tooling (A) in the cylinder block.
3. Use a suitable lifting device to install the cylinder head. The weight of the cylinder head is
approximately 57 kg (126 lb).
Note: Ensure that the cylinder head is positioned on dowels (10). Take care not to damage
the machined surfaces of the cylinder head during installation.
4. Remove the Tooling (A).
2/6
2020/6/20

5. Clean the threads of the setscrews that secure the cylinder head. Inspect the threads of the
setscrews that secure the cylinder head.
Note: Do not use the setscrews if there is any visual reduction in the diameter of the threads
(Y) that has not been engaged with the cylinder block. Use a straight edge to check the
bolts.
6. Apply clean engine oil to the threads and the shoulder of the setscrews that secure the
cylinder head before installation.
7. Install the setscrews (8) in cylinder head (9).
Note: The short setscrews are installed in holes that are marked 2, 5, 6, 7, 8, 9, and 10.
Note: The long setscrews are installed in holes that are marked 1, 3, and 4.
8. Tighten the setscrews in numerical order to a torque of 50 N·m (37 lb ft). Refer to
Illustration 3.
9. Tighten the setscrews in numerical order to a torque of 100 N·m (74 lb ft). Refer to
Illustration 3.
3/6
2020/6/20

10. Use the Tooling (B) to achieve the correct final torque.
Note: If the Tooling (B) is not available, place an index mark on each setscrew.
11. Tighten the setscrews in numerical order. Refer to Illustration 3.
a. Turn the short setscrews (2, 5, 6, 7, 8, 9, and 10) for an additional 225 degrees.
b. Turn the long setscrews (1, 3, and 4) for an additional 270 degrees.
12. Install new O-ring seals on the bypass tube (7). Apply Tooling (C) to the O-ring seals.
Install the bypass tube in the cylinder head. Install the setscrews (6).
4/6
2020/6/20

13. Connect the tube assembly (5) to the cylinder head.
14. Connect the harness assembly (4) to the coolant temperature sensor.
15. Install bolt (1) and the fuel line to the cylinder head.
16. Fill the cooling system with coolant. Fill the lubrication system with engine oil.
Note: Refer to Operation and Maintenance Manual, "Refill Capacities" for the cooling
system capacity and the lubrication system capacity of the engine.
End By:
a. Install the glow plugs. Refer to Disassembly and Assembly Manual, "Glow Plugs - Remove
and Install".
b. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
c. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
d. Install the fuel injection Nozzles. Refer to Disassembly and Assembly Manual, "Fuel
Injection Nozzles - Install".
e. Install the pipe for the boost control.
f. Install the fuel priming pump. Refer to Disassembly and Assembly Manual, "Fuel Priming
Pump and Fuel Filter Base - Remove and Install".
g. Install the hose from the integral air inlet to the air filter. Refer to the OEM information for
further details.
h. Refill the engine with coolant and engine oil. Refer to the Operation and Maintenance
Manual for the correct procedure, the quantities, the coolant specification, and the
specification for the engine oil.
Sat Jun 20 23:01:08 UTC+0800 2020
5/6
2020/6/20

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02333592
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
A 1U-7262 Telescoping Magnet 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
1/3
2020/6/20

1. Use Tooling (A) to remove lifters (1).
Note: Place an identification mark on the lifters for installation purposes.
Table 2
Required Tools
A 1U-7262 Telescoping Magnet 1
NOTICE
1. Lubricate the lifters with clean oil before installing the lifters in the cylinder block.
2/3
2020/6/20

2. Use Tooling (A) to install lifters (1).
Note: Ensure that the lifters are installed in the original location and that the lifters are
seated correctly.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Sat Jun 20 23:02:07 UTC+0800 2020
3/3
2020/6/20

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02299051
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
a. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Shaft and Pushrod - Remove".
b. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
1. Turn the engine upside-down so the valve lifters are held in a position away from the
camshaft.
1/3
2020/6/20

NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2. Carefully remove camshaft (3) from the cylinder block.
NOTICE
Note: Ensure that the camshaft is clean. Lubricate the camshaft with clean engine oil prior
to installation.
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2/3
2020/6/20

1. Carefully install camshaft (3) in the cylinder block.
End By:
a. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
b. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Sat Jun 20 23:03:07 UTC+0800 2020
3/3
2020/6/20

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02299758
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
1/3
2020/6/20

1. Use the Tooling (A) in order to remove the camshaft bearing (1) from the cylinder block.
Table 2
Required Tools
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
2/3
2020/6/20

1. Use the Tooling (A) in order to install the camshaft bearing (1) into the bore in the cylinder
block.
Note: Align the oil hole in camshaft bearing (1) with the oil hole in the bore in the cylinder
block.
Note: The camshaft bearing must be inserted until the front edge of the bearing is flush with
the face of the recess in the cylinder block.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Sat Jun 20 23:04:06 UTC+0800 2020
3/3
2020/6/20

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05003149
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5
2020/6/20

1. Remove all dirt, oil, and grease from the exterior surfaces of the oil pan (5).
2. Operate the engine until the engine is warm. Stop the engine.
3. Remove the oil drain plug (6) and the O-ring seal. Drain the engine oil into a suitable
container for storage or disposal.
Note: Refer to the Operation and Maintenance Manual, "Refill Capacities" for information
on the capacity of the lubrication system.
Note: Ensure that the engine oil pan is fully supported before the oil pan is removed.
Particular care must be taken with the cast iron version of the engine oil sump as this
version is heavy.
4. Remove the setscrews (3) and the setscrews (4) from the engine oil pan (5).
5. Remove the engine oil pan (5) and remove the gasket (1) from the cylinder block. Discard
the gasket (1).
6. If necessary, remove the nut (2), the seal, and the tube assembly from the engine oil pan.
7. Clean the engine oil pan (5) with a suitable cleaning fluid. Ensure that all of the cleaning
fluid is removed.
2/5
2020/6/20

Table 1
Required Tools
A -
Guide Bolt
(M8 x 1.25 x 70 mm)
4
B - Loctite 5900 -
C - Loctite 243 -
NOTICE
1. Clean the flange face of the engine oil pan (5) and the flange face of the cylinder block.
2. When the gasket for the oil pan is removed, damage may occur to the existing seal in the
groove of the bridge. If the seal is damaged, apply a sufficient amount of Tooling (B) in
order to fill the groove. The groove must be completely filled.
3. Apply Tooling (B) to the joint between the cylinder block and the front housing.
3/5
2020/6/20

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

4. Install Tooling (A) in the cylinder block in Hole (X).
Note: New setscrews have sealant on the first 13 mm (0.5 inch) of the threads. In order to
reuse the old setscrews, clean the old sealant from the bolts and apply Tooling (C) to the
setscrews.
Note: Ensure that the engine oil pan is properly supported while the engine oil pan (5) is
installed onto the cylinder block.
5. Position a new gasket (1) and the engine oil pan (5) on the cylinder block. Install the
setscrews (3 and 4) in order to secure the engine oil pan to the cylinder block. Tighten the
setscrews finger tight.
6. Remove the Tooling (A) and install the remaining setscrews (3 an 4). Tighten the setscrews
(3) in Hole (Y) to a torque of 22 N·m (16 lb ft).
7. Tighten the remaining setscrews (3 and 4) to a torque of 22 N·m (16 lb ft).
8. Inspect the O-ring for the drain plug (6). Replace the O-ring if it is necessary. Install the O-
ring seal and drain plug (6). Tighten the drain plug to a torque of 34 N·m (25 lb ft).
9. If necessary, install the seal and the tube assembly in the engine oil pan. Tighten the nut (2)
to a torque of 18 N·m (13 lb ft).
10. Fill the engine oil pan to the correct level that is indicated on the engine oil level gauge.
4/5
2020/6/20

Note: Refer to the Operation and Maintenance Manual, "Refill Capacities" for the
lubrication system capacity of the engine.
Sat Jun 20 23:05:05 UTC+0800 2020
5/5
2020/6/20

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02300831
Piston Cooling Jets - Remove and Install
SMCS - 1331-010
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
1/3
2020/6/20

Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF00001 and up).pdf

More Related Content

More from fusjekkdmdmd2w (20)

Recently uploaded (20)

Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF00001 and up).pdf