Caterpillar Cat 313D2 Excavator (Prefix LCY) Service Repair Manual (LCY00001 and up).pdf

Service Repair Manual
Models
313D2 and 313D2 L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D2 EXCAVATOR LCY
Configuration: 313D2 L Excavator LCY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
313D2 Excavator Machine Systems
Media Number -UENR7323-03 Publication Date -01/09/2015 Date Updated -14/12/2017
i06303560
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
C 8T-6699 Bolts 2
D
1P-0074 Slide Hammer Puller Gp 1
4C-5666 Threaded Adapter 1
123-6702 Backlash Gauge Gp 1
E 1P-0510 Driver Gp 1
F 8H-0663 Bearing Puller Gp 1
G 1P-1863 Retaining Ring Pliers 1
H 9U-7346 Spanner Wrench As 1
Start By:
a. Remove the final drive and the travel motor. Refer to Disassembly and Assembly Manual ,
"Final Drive and Travel Motor - Remove".
NOTICE
1/23
313D2 L Excavator LCY00001-UP (MACHINE) POWERED BY C4.4 Engine(M007...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor. The weight of the sprocket is
approximately 39 kg (85 lb).
3. Mark the alignment of the final drive and travel motor for reassembly purposes. The parts
must be reinstalled in the original locations.
2/23
2020/5/16

https://www.aservicemanualpdf.com/
My Dear Friend! Thank you very
much for visiting. Full manual if
required, please enter the
following URL into your browser.
https://www.aservicemanualpdf.com/

Illustration 1 g00940682
4. Use Tooling (A) and a suitable lifting device to position the final drive and the travel motor
onto Tooling (B). The combined weight of the final drive and travel motor is approximately
170 kg (375 lb).
5. Drain the oil from the final drive into a suitable container for storage or for disposal. Refer
to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the final
drive.
6. Remove fittings (1). Remove fittings (2) from traction control valve (3).
7. Remove nine bolts (4) that secure traction control valve (3) to the final drive.
8. Use two persons to remove traction control valve (3) from the final drive. The weight of
travel brake valve (3) is approximately 27 kg (60 lb).
3/23
2020/5/16

9. Remove valve plate (5) and O-ring seal (6).
10. Use Tooling (D) to remove bearing (7).
Disassembly of the Counterbalance Valve
4/23
2020/5/16

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Position the counterbalance valve, as shown. Remove plug (8) and adapter (9).
2. Remove spring (10) and spool (11).
5/23
2020/5/16

3. Remove relief valve assemblies (12).
4. Remove seat (13). Seat (13) is pressed onto valve (17). Use new parts if seat (13) or valve
(17) is damaged. Do not disassemble these components. Make sure that you reuse the other
component.
5. Remove backup ring (14) and O-ring seal (15).
6. Remove O-ring seal (22).
7. Remove nut (20).
8. Remove screw (27).
9. Remove stopper (26). Remove backup ring (19) and O-ring seal (18) from stopper (19).
10. Remove valve (21), piston (25), and spring (16) from the housing.
11. Remove backup ring (23) and O-ring seal (24) from piston (25).
6/23
2020/5/16

12. Remove covers (28) and the O-ring seals.
13. Remove springs (29), guides (30), and spool assembly (31).
7/23
2020/5/16

14. Remove valve (32), spring (33), and ball (34) from one end of spool (35). Repeat for the
other end of spool (35).
8/23
2020/5/16

15. Remove plug (36), spring (38), and piston (39) from both sides of the housing assembly.
16. Remove O-ring seal (37) from each plug (36).
Note: Remove the remaining allen head bolts from the housing assembly for cleaning
purposes, if necessary. Each allen head bolt has an O-ring seal. Check the O-ring seal for
wear or for damage. Replace the O-ring seal, if necessary.
Disassembly of the Travel Motor
1. Remove O-ring seal (40) and springs (41).
9/23
2020/5/16

2. Install Tooling (C) onto piston assembly (42). Use Tooling (C) and a suitable prybar to
remove piston assembly (42) from body (43).
3. Remove O-ring seals (45) and (46) from piston assembly (42). Remove backup rings (44)
and (47) from piston assembly (42).
10/23
2020/5/16

4. Use suitable drivers or a suitable lever to remove guide assembly (48).
5. Remove O-ring seal (49) and backup ring (50) from guide assembly (48).
11/23
2020/5/16

6. Remove four separator plates (51) and four friction plates (52). Note the alternating order of
separator plates (51) and friction plates (52) for assembly purposes.
Note: Do not allow the components of barrel assembly (53) to come apart while you
remove barrel assembly (53). The components of barrel assembly (53) must be reinstalled
into the original positions.
Note: Oil will drain from the final drive. Place a suitable container under the final drive for
storage or disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for
the fluid capacity of the final drive.
7. Position the final drive horizontally.
8. Remove barrel assembly (53).
12/23
2020/5/16

Note: Mark the component locations for assembly purposes before you disassemble barrel
assembly (53).
9. Remove piston assemblies (54) and retainer (55) from barrel assembly (53).
10. Remove retainer (56), spacer (57), and springs (58) from barrel assembly (53).
13/23
2020/5/16

11. Put location marks on cam plate (59) for assembly purposes. Make sure that the thick end of
cam plate (59) is adjacent to the opening that is across body (43). Remove cam plate (59).
14/23
2020/5/16

12. Remove piston (60) and spring (62).
13. Remove key (61).
Disassembly of the Final Drive
1. Use a suitable lifting device to position the final drive on Tooling (B), as shown. The weight
of the final drive is approximately 200 kg (441 lb).
2. Remove plugs (63). Remove the O-ring seals from plugs (63). Check the O-ring seals for
wear or for damage. Replace the O-ring seals, if necessary.
3. Remove bolts (65). Remove cover (64).
15/23
2020/5/16

4. Raise the temperature of bolts (66) in order to loosen the thread sealant.
5. Remove bolts (66) and plate (67).
6. Remove sun gear (68).
16/23
2020/5/16

7. Attach Tooling (A) and a suitable lifting device to carrier assembly (69). Remove carrier
assembly (69), planetary gear assembly (70), and bearing assembly (71) as a unit.
8. Remove planetary gear (70) and bearing assembly (71) from carrier assembly (69). Remove
the remaining planetary gears (70) and bearings (71).
9. Remove sun gear (72).
17/23
2020/5/16

10. Raise the temperature of bolts (73) in order to loosen the thread sealant. Remove bolts (73).
Remove plate (74).
11. Remove retaining ring (75) from sun gear (72). Check retaining ring (75) for wear or for
damage. Replace retaining ring (75), if necessary.
12. Remove planetary gear (76).
18/23
2020/5/16

13. Remove bearing (77), race (78), and thrust washer (79).
14. Repeat Steps 12 and 13 in order to remove the remaining planetary gear assemblies.
15. Remove bolt (80) and plate (81).
19/23
2020/5/16

16. Use Tooling (H) to remove nut (82).
17. Install Tooling (A) and a suitable lifting device to housing (83). The weight of housing (83)
is approximately 35 kg (77 lb).
18. Remove housing (83) from body assembly (84).
20/23
2020/5/16

19. Remove Duo-Cone Seal Gp seal (85) from the body assembly. Remove the Duo-Cone Seal
Gp seal from the housing.
20. Remove both bearings (86) from housing (83).
21/23
2020/5/16

21. Remove both bearings (87) from housing (83).
22. Position body assembly (84) horizontally. Remove shaft assembly (88), the bearing, and the
retaining ring.
22/23
2020/5/16

23. Use Tooling (G) to remove retaining ring (89) from shaft assembly (88).
24. Use Tooling (E), Tooling (F), and a suitable press to remove bearing (90).
25. Remove lip seal (91) from the body assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 16 23:26:11 UTC+0800 2020
23/23
2020/5/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D2 EXCAVATOR LCY
Configuration: 313D2 L Excavator LCY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
313D2 Excavator Machine Systems
Media Number -UENR7323-03 Publication Date -01/09/2015 Date Updated -14/12/2017
i07219742
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 422-5474 M16x2x24 mm Lifting Eye Assembly 2
B 1P-2420 Transmission Repair Stand 1
C 8H-0663 Bearing Puller Assembly 1
D 422-5473 M12x1.75x21 mm Lifting Eye Assembly 2
E 422-5472 M10x1.5x16 mm Lifting Eye Assembly 2
F 1U-9895 Crossblock 1
Start By:
a. Remove the final drive and the travel motor assembly.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/22
2020/5/16

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor assembly. The weight of the
sprocket is approximately 39 kg (85 lb).
3. Mark the alignment of the final drive and travel motor for reassembly purposes. The parts
must be reinstalled in the original locations.
4. Use Tooling (A) and a suitable lifting device to position final drive assembly (1) onto
Tooling (B). The weight of final drive assembly (1) is approximately 163 kg (360 lb).
2/22
2020/5/16

5. Drain the oil from final drive assembly (1) into a suitable container for storage or for
disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity
of the final drive.
6. Remove plug (2), plugs (3), and the O-ring seals.
3/22
2020/5/16

7. Remove plugs (4) and the O-ring seals.
8. Remove plug (5), spring (7), valve (6), and the O-ring seals.
4/22
2020/5/16

Caterpillar Cat 313D2 Excavator (Prefix LCY) Service Repair Manual (LCY00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 313D2 Excavator (Prefix LCY) Service Repair Manual (LCY00001 and up).pdf (20)

More from tuzhiyou2 (20)

Recently uploaded (20)

Caterpillar Cat 313D2 Excavator (Prefix LCY) Service Repair Manual (LCY00001 and up).pdf