Caterpillar Cat 314D LCR Excavator (Prefix XHR) Service Repair Manual (XHR00001 and up).pdf

Service Repair Manual
Models
314D CR and 314D LCR
Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR XHR
Configuration: 314D CR & 314D LCR Excavator XHR00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02743771
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B Forcing bolts M16 - 2 by 120 mm 2
Start By:
a. Remove the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
b. Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
314D CR & 314D LCR Excavator XHR00001-UP (MACHINE) POWERED BY C4.2...
2020/5/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01374966
1. Remove muffler brackets (1).
2. Remove bolts (2).
3. Install Tooling (A) and a suitable lifting device onto flywheel (3).
4. Use Tooling (B) in order to remove flywheel (3) out of the housing. The weight of flywheel
(3) is approximately 50 kg (110 lb).
2/3
2020/5/25

5. Perform the following procedure in order to remove the flywheel ring gear.
Typical Example
a. Place flywheel (3) and ring gear (4) on suitable cribbing.
Note: Mark the orientation of ring gear (4) on flywheel (3) for assembly purposes.
Always wear protective gloves when handling parts that have been
heated.
b. Raise the temperature of ring gear (4) uniformly.
c. Remove the ring gear (4) by tapping ring gear (4) all the way around flywheel (3).
d. Reposition flywheel (3) in order to remove ring gear (4).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 25 15:04:00 UTC+0800 2020
3/3
2020/5/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02744399
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
NOTICE
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Raise the temperature of the ring gear 149 °C (300 °F).
1/3
2020/5/25

b. Use a suitable press in order to install the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
2. Install Tooling (A) and a suitable lifting device onto flywheel (3).
3. Install flywheel (3). The weight of flywheel (3) is approximately 50 kg (110 lb).
4. Install bolts (2) in order to secure flywheel (3) onto the crankshaft. Tighten bolts (2) to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tooling (A) from flywheel (3).
2/3
2020/5/25

6. Install muffler brackets (1).
7. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
End By:
a. Install the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
b. Install the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
Mon May 25 15:04:57 UTC+0800 2020
3/3
2020/5/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3
2020/5/25

of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3
2020/5/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Table 1
Required Tools
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3
2020/5/25

2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3
2020/5/25

e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Mon May 25 15:06:51 UTC+0800 2020
3/3
2020/5/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02742697
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
B 1P-0510 Driver Group 1
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Remove the flywheel and ring gear. Refer to Disassembly and Assembly, "Flywheel -
Remove".
NOTICE
1/4
2020/5/25

1. Install Tooling (A), and a suitable lifting device onto flywheel housing (3).
2. Remove bolts (2) and the washers that secure flywheel housing (3) to the cylinder block.
3. Remove flywheel housing (3). The weight of flywheel (3) is approximately 29 kg (65 lb).
4. Remove gasket (1) (not shown).
5. Use Tooling (B) in order to remove the oil seal (4) (not shown).
Table 2
Required Tools
NOTICE
2/4
2020/5/25

1. Use Tooling (B) in order to install the oil seal (4) (not shown).
2. Check the condition of two dowels (not shown). If dowels are damaged, use new parts for
replacement.
3. Clean old gasket (1) (not shown) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
4. Place flywheel housing (3) in position on the cylinder block.
5. Install the washers and bolts (2) in order to secure flywheel housing (3) to the cylinder
block.
6. Remove Tooling (A).
End By:
3/4
2020/5/25

a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
Mon May 25 15:07:48 UTC+0800 2020
4/4
2020/5/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i06790404
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
A 1P-2321 Combination Puller 1
B 6V-9120 Socket(1)
1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
1. Remove the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
1/4
2020/5/25

2. Use Tooling (B) in order to remove nut (1) and washer (2) from the threaded end of the
crankshaft.
3. Use Tooling (A) in order to remove crankshaft pulley (3) from the engine.
2/4
2020/5/25

4. If it is necessary to remove wear sleeve (4) from crankshaft pulley (3), use a suitable
hammer and a suitable chisel. Hold the suitable chisel at right angles to the surface of the
wear sleeve. Tap the wear sleeve in three places. You can remove the wear sleeve once the
tension is released.
Table 2
Required Tools
B 6V-9120 Socket(1)
1
C 1P-0510 Driver Gp 1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
1. Raise the temperature of the wear sleeve. Use Tooling (C) in order to install the wear sleeve
onto the crankshaft pulley.
3/4
2020/5/25

2. Ensure that baffle plate (5) is oriented, as shown.
3. Position crankshaft pulley (3) onto the engine.
4. Install washer (2) and nut (1). Use Tooling (B) in order to tighten nut (1) to a torque of
707.5 ± 57.5 N·m (522 ± 42 lb ft).
5. Install the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
Mon May 25 15:08:44 UTC+0800 2020
4/4
2020/5/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02742689
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
A 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
NOTICE
containing fluids.
1/2
2020/5/25

Cat products.
Typical Example
1. Drill three evenly spaced 3.0 mm (0.12 inch) holes in crankshaft front seal (1).
2. Use Tooling (A) in order to remove crankshaft front seal (1). Remove the seal evenly by
alternating the position of Tooling (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Mon May 25 15:09:41 UTC+0800 2020
2/2
2020/5/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02742692
Crankshaft Front Seal - Install
SMCS - 1160-012
Table 1
Required Tools
A 9U-6180 Front Seal Installer 1
NOTICE
1/2
2020/5/25

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Typical Example
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Use Tooling (A) in order to install new crankshaft front seal (1) in the front housing.
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Mon May 25 15:10:38 UTC+0800 2020
2/2
2020/5/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
A 9U-6148 Idler Shaft Puller 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
NOTICE
1/4
2020/5/25

containing fluids.
Cat products.
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4
2020/5/25

Caterpillar Cat 314D LCR Excavator (Prefix XHR) Service Repair Manual (XHR00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 314D LCR Excavator (Prefix XHR) Service Repair Manual (XHR00001 and up).pdf (8)

More from 8ufjsekddm8u (20)

Recently uploaded (20)

Caterpillar Cat 314D LCR Excavator (Prefix XHR) Service Repair Manual (XHR00001 and up).pdf