Caterpillar Cat 318C Excavator (Prefix DAH) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
318C Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318C EXCAVATOR DAH
Configuration: 318C Excavators DAH00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
318C Excavator Machine Systems
Media Number -RENR6647-04 Publication Date -01/03/2009 Date Updated -05/03/2009
i02275023
Final Drive - Disassemble
SMCS - 4050-015
S/N - BTG1-UP
S/N - DAH1-UP
S/N - FAA1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 154-6360 Forcing Bolt 2
C 1P-2320 Combination Puller 1
D 138-7576 Link Bracket 2
E
8B-7554 Bearing Cup Puller Gp 1
7S-7786 Puller Leg 2
8B-7560 Step Plate 1
F 246-7504 Socket 1
G
6V-6080 Torque Multiplier Gp 1
9U-5006 Torque Wrench 1
H FT-2993 Reaction Bar 1
1/11
318C Excavators DAH00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP35...
2020/11/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

J 154-9316 Metric Thread File 1
K 1P-1864 Retaining Ring Pliers As 1
L 1U-8151 Drill Bit (5 mm) 1
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the final drive into a suitable container. Refer to Operation and Maintenance Manual,
"Capacities (Refill)".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
2. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g01139499
2/11
2020/11/27

https://www.ebooklibonline.com
Hello dear friend!
Thank you very much for reading.
Enter the link into your browser.
The full manual is available for immediate
download.
https://www.ebooklibonline.com

3. Fasten the final drive to Tooling (A), as shown. If necessary, remove the final drive
sprocket. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
The weight of the final drive is approximately 250 kg (550 lb).
4. Remove drain plugs (1) .
5. Remove bolts (2) .
6. Use Tooling (B) to separate cover (3) from the final drive. Remove cover (3) .
3/11
2020/11/27

7. Remove planetary assembly (4) .
8. Remove O-ring seal (5) .
9. Remove retaining ring (6) (not shown).
10. Use Tooling (C) in order to remove planetary gear (7) .
4/11
2020/11/27

11. Remove retaining ring (8) and bearing (9) .
12. Repeat Steps 9 through 11 for the remaining planetary gears.
13. Remove retaining ring (11) and shaft (10) from carrier (12) .
14. Use Tooling (D) to remove ring gear (13). The weight of ring gear (13) is approximately 32
kg (70 lb).
5/11
2020/11/27

15. Use Tooling (K) in order to remove retaining ring (14) .
16. Use Tooling (E) in order to remove planetary gear (15) .
17. Use a suitable press in order to remove bearings (16) from gear (15) .
6/11
2020/11/27

Note: If the bearings are removed, the bearings must be replaced with new bearings.
18. Repeat Steps 15 through 17 for the remaining planetary gears.
19. Remove O-ring seal (17) .
20. Straighten the tab on lock washers (18) .
21. Remove bolts (20), lock washers (18), and balls (21) from bearing retainer nut (19) .
7/11
2020/11/27

22. Use Tooling (L) to clean the threads in the housing. Remove approximately 2.0 mm (0.08
inch) of material from the housing. This is done in order to prevent the retaining nut threads
from being damaged when retaining nut (19) is removed.
23. Install Tooling (F) on retainer nut (19). Install bolts (22) through Tooling (F) and into the
drilled holes in retainer nut (19) .
8/11
2020/11/27

24. Install Tooling (F), (G), and (H) (not shown).
25. Use Tooling (D) and a suitable lifting device in order to remove support ring (23). The
weight of support ring (23) is approximately 23 kg (50 lb).
26. Remove bearing cone (24) from support ring (23) .
9/11
2020/11/27

27. Remove Duo-Cone seal (25) from support ring (23) .
28. Remove bearing cups (26) .
29. Remove bearing cone (27) from housing (28) .
10/11
318C Excavators DAH00001-UP (MACHINE) POWERED BY 3066 Engine(SEBP...
2020/11/27

30. Remove Duo-Cone seal (29) from housing (28) .
31. Use Tooling (J) in order to repair any damaged threads on housing (28) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 27 02:39:40 UTC+0800 2020
11/11
2020/11/27

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02275024
Final Drive - Assemble
SMCS - 4050-016
S/N - BTG1-UP
S/N - DAH1-UP
S/N - FAA1-UP
Assembly Procedure
Table 1
Required Tools
A 1P-2420 Transmission Repair Stand 1
D 138-7576 Link Bracket 2
F 246-7504 Socket 1
G
6V-6080 Torque Multiplier Gp 1
9U-5006 Torque Wrench 1
H FT-2993 Reaction Bar 1
K 1P-1864 Retaining Ring Pliers As 1
M 1U-6396 O-Ring Assembly Compound 1
N 1U-6434 Duo-Cone Seal Installer As 1
P 246-7503 Punch 1
1/11
2020/11/27

Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring seal may not have the
same sealing properties as a new O-ring seal. Use Tooling (M) during the assembly procedure.
1. Use Tooling (N) to install Duo-Cone seal (29) onto housing (28) .
2. Install bearing cone (27) onto housing (28) .
2/11
2020/11/27

3. Lower the temperature of bearing cups (26). Install bearing cups (26) into support ring (23) .
4. Use Tooling (N) to install Duo-Cone seal (25) into support ring (23) .
3/11
2020/11/27

5. Use Tooling (D) and a suitable lifting device in order to install support ring (23) onto
housing (28) .
6. Install bearing cone (24), as shown.
7. Install retainer nut (19) .
4/11
2020/11/27

8. Install Tooling (F), (G), and (H) (not shown).
9. Install bolts (22) through Tooling (F) and into retainer nut (19). Tighten retainer nut (19) to
a torque of 3500 N·m (2581 lb ft).
5/11
2020/11/27

10. Use Tooling (P) and a suitable hammer to make a dimple 0.9 mm to 1.25 mm (0.04 to 0.050
inch) deep in housing (28) .
11. Install balls (21), lock washers (18), and bolts (20) .
12. Fold the tab on lock washers (18) over bolts (20), as shown.
13. Install O-ring seal (17) .
6/11
2020/11/27

14. Install bearing (16) into gear (15) .
15. Raise the temperature of gear (15). Install gear (15) onto housing (28) .
Note: Make sure that the chamfered side of the bearing is installed against the carrier.
7/11
2020/11/27

16. Use Tooling (K) to install retaining ring (14) .
17. Repeat Steps 14 through 16 for the other two gears.
18. Use Tooling (D) and a suitable lifting device in order to install ring gear (13) onto housing
(28). The weight of ring gear (13) is approximately 32 kg (70 lb).
19. Install shaft (10) and retaining ring (11) onto carrier (12) .
8/11
2020/11/27

20. Install bearing (9) and retaining ring (8) into the planetary gear.
21. Raise the temperature of planetary gear assembly (7). Install planetary gear assembly (7)
onto carrier (12) and install retaining ring (6) .
22. Repeat Steps 20 through 21 for the remaining two gears.
9/11
2020/11/27

23. Install planetary assembly (4) into the final drive housing.
24. Install O-ring seal (5) .
25. Measure the distance between thrust button (3A) and shaft (10). The distance between shaft
(10) and thrust button (3A) should be 1.0 ± 0.5 mm (0.04 ± 0.02 inch).
10/11
2020/11/27

26. Install cover (3) and bolts (2). Tighten bolts (2) evenly to a torque of 295 ± 50 N·m (218 ±
37 lb ft).
27. Install drain plugs (1). Tighten drain plugs (1) to a torque of 40 ± 5 N·m (30 ± 4 lb ft).
28. Make sure that the final drive is filled with oil before the final drive is put back into service.
Refer to Operation and Maintenance Manual, "Capacities (Refill)".
29. Install the final drive sprocket if the sprocket was removed from the main housing. Refer to
Disassembly and Assembly, "Final Drive Sprocket - Remove and Install" in this manual for
the installation of the final drive sprocket.
30. Remove the final drive from Tooling (A). The weight of the final drive is approximately
250 kg (550 lb).
End By: Install the final drive. Refer to Disassembly and Assembly, "Final Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 27 02:40:40 UTC+0800 2020
11/11
2020/11/27

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07192988
Final Drive - Install
SMCS - 4050-012
Installation Procedure
Table 1
Required Tools
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C - Loctite C5A Copper Anti-Seize -
Table 2
Torque Values of Bolts (3)
Bolt Size Torque
M16 90 ± 15 N·m (66 ± 11 lb ft) and turn an additional angle of 60 ± 5 degrees.
1/3
2020/11/27

1. Attach Tooling (B) and a suitable lifting device to final drive (1). The weight of final drive
(1) and the sprocket is approximately 312 kg (688 lb). Position the final drive in the frame.
Note: Make sure that bolt holes (2) for the travel motor are in the correct position.
Note: Make sure that bolts (3), the washers, the motor housing, and the frame are clean and
free of protective coating and oil.
2. Before assembly remove all compounds, oil, and dust from the female threads.
3. Apply Tooling (C) to the threads of bolt (3). Install bolts (3) and the washers in the final
drive. Tighten bolts (3) to a torque specified in Table 2.
4. Refer to Service Magazine, M0083843, "An Improved Bolt Tightening Procedure for the
Critical Joints Is Now Used on All Excavators" for more detail information.
5. Remove Tooling (B) and the suitable lifting device from the final drive.
2/3
2020/11/27

Caterpillar Cat 318C Excavator (Prefix DAH) Service Repair Manual Instant Download.pdf

More Related Content

Similar to Caterpillar Cat 318C Excavator (Prefix DAH) Service Repair Manual Instant Download.pdf (20)

More from tou30qing (14)

Recently uploaded (20)

Caterpillar Cat 318C Excavator (Prefix DAH) Service Repair Manual Instant Download.pdf