Caterpillar cat 320 d rr excavator (prefix fxk) service repair manual (fxk00001 and up)

Service Repair Manual
Models
320D RR and 320D LRR
Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR FXK
Configuration: 320D RR & 320D LRR Excavators FXK00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i03706683
Crankshaft Main Bearings - Remove
SMCS - 1203-011
Removal Procedure
Start By:
a. Remove the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00602470
1/2(W)
w
2020/10/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...

1. Remove the main bearings (1) (upper shell) from the main bearing housing of the engine
cylinder block. The 3066 Engine has seven main bearings while the 3064 Engine has five
main bearings.
2. Remove thrust washers (2) from the cylinder block and from the rear main cap.
3. Remove the lower halves of the crankshaft main bearings (4) from the main bearing cap (3).
Note: Be careful not to damage the bearings. Mark each main bearing in order to ensure
installation in the original location.
Note: Check the condition of the crankshaft main bearings. Refer to the Guideline For
Reusable Parts, SEBF8009, "Main and Connecting Rod Bearings" or refer to the Guideline
For Reusable Parts, SEBV0544, "Engine Bearings and Crankshafts".
Note: Refer to the Specifications Module, "Main Bearing Journal" for more information on
crankshaft main bearings and the main bearing journals.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 24 23:40:03 UTC+0800 2020
2/2(W)
w
2020/10/24

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01135299
Crankshaft Main Bearings - Install
SMCS - 1203-012
Installation Procedure
NOTICE
1. Install the upper halves of the crankshaft main bearings (1) in the main bearing housing of
the cylinder block.
1/2(W)
w
2020/10/24

Note: Ensure that the main bearing tab fits in the tab groove of the bearing housing of the
cylinder block.
2. Install thrust washers (2) into the cylinder block and the rear main cap.
Note: Install the thrust washers with the oil grooves toward the outside.
3. Install the lower halves of the crankshaft main bearings (4) into the crankshaft main bearing
caps (3).
Note: Ensure that the main bearing tab fits in the tab groove of the crankshaft main bearing
cap.
End By:
a. Install the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Install".
Sat Oct 24 23:40:59 UTC+0800 2020
2/2(W)
w
2020/10/24

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01576856
Crankshaft - Remove
SMCS - 1202-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-9120 Socket (1)
1
( 1 )
Tool (A) is a 46 mm socket.
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
B. Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear
Seal - Remove".
C. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
D. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
1/5(W)
w
2020/10/24

1. Remove two bolts (1) from oil supply tube (2). Remove oil supply tube (2) from the engine
cylinder block.
2. Check condition of the O-ring seal (3) on the oil supply tube (2). If the O-ring is damaged,
use a new part for replacement.
2/5(W)
w
2020/10/24

3. Install nut (4) and the washer onto the crankshaft. Use Tool (A) to turn the crankshaft.
4. Remove nuts and bolts (5) that secure connecting rod caps (6) to the connecting rods.
Remove connecting rod caps (6) from the connecting rods.
Note: Be careful not to damage the bearings. Mark each connecting rod cap and the bearing
in order to ensure installation in the original location.
5. Carefully push the connecting rods and the pistons into the top of bores.
6. Remove bolts (7) that secure crankshaft main bearing caps (8) in position in the engine
cylinder block. Remove crankshaft main bearing caps (8) from the engine.
Note: Be careful not to damage the bearings. Mark each crankshaft main bearing cap and
the bearing in order to ensure installation in the original location.
3/5(W)
w
2020/10/24

7. Fasten a suitable lifting device and straps to crankshaft (9). Remove the crankshaft. The
weight of the crankshaft for the 3064 engine is 84 kg (185 lb). The weight of the crankshaft
for the 3066 engine is 99 kg (220 lb).
Note: Be careful not to damage the finished surfaces on the crankshaft.
8. Remove the upper halves of crankshaft main bearings (10). If necessary, remove thrust
washers (11) .
4/5(W)
w
2020/10/24

9. If necessary, use a hammer and a chisel to remove the wear sleeve (12) for the crankshaft
rear seal. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
Note: Take extreme care not to damage the wear sleeve, if it is not necessary to remove the
wear sleeve.
Sat Oct 24 23:41:55 UTC+0800 2020
5/5(W)
w
2020/10/24

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01568784
Crankshaft - Install
SMCS - 1202-012
Table 1
Required Tools
A 6V-9120 Socket (1)
1
B 8T-5096 Dial Indicator 1
( 1 )
Tool (A) is a 46 mm socket.
NOTICE
1/5(W)
w
2020/10/24

1. If the thrust washers were removed, then install a thrust washer (11) on the rear face of the
crankshaft with the oil groove toward the outside.
2. Place the upper halves of crankshaft main bearings (10) in the cylinder block. Place the
lower halves of the crankshaft main bearings in crankshaft main bearing caps. Install the
bearings with the main bearing tabs in the correct position. Lubricate the bearings with
clean engine oil.
3. Lubricate the crankshaft journals with clean engine oil. Fasten a suitable lifting device and
straps to crankshaft (9). The weight of the crankshaft for the 3064 engine is 84 kg (185 lb).
The weight of the crankshaft for the 3066 engine is 99 kg (220 lb). Position crankshaft (9)
onto the upper halves of the crankshaft main bearings.
2/5(W)
w
2020/10/24

4. Install main bearings into main bearing caps (8). Install the bearings with the main bearing
tabs in the correct position. Lubricate the bearings with clean engine oil.
5. Place the thrust washers on the rear main bearing cap. Install the rear main bearing cap and
two seals on the rear journal of the cylinder block.
6. Install crankshaft main bearing caps (8). Put clean engine oil on the threads of the main
bearing cap bolts. Install main bearing cap bolts (7). Tighten the bolts evenly to a torque of
137 ± 5 N·m (101 ± 4 lb ft).
Note: Ensure that the crankshaft main bearing caps are installed in the original locations.
7. Cut off the excess length on the two seals on the rear journal of the cylinder block.
8. Check the end play of the crankshaft with Tool (B). The end play must be 0.100 to 0.264
mm (0.0039 to 0.0104 inch). Refer to the Testing and Adjusting Module, "Basic Block" for
more information on crankshaft end play.
3/5(W)
w
2020/10/24

9. Apply a light coat of clean engine oil to the connecting rod bearing surfaces and to the
connecting rod journals. Install the connecting rods onto the connecting rod journals.
10. Install the lower half of the connecting bearings into the corresponding connecting rod caps
and install connecting rod caps (6) .
Note: Align the tabs on the back of the connecting rod bearings with the tab grooves in the
connecting rod caps.
Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and
Connecting Rods - Install".
11. Check for free crankshaft rotation by rotating the crankshaft for two complete revolutions.
Use Tool (A) on crankshaft pulley nut (4) in order to rotate the crankshaft.
4/5(W)
w
2020/10/24

12. Install O-ring seal (3) on oil supply tube (2) .
13. Position oil supply tube (2). Install two bolts (1) in order to secure the oil supply tube to the
cylinder block.
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
b. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
c. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
d. Install the crankshaft rear seal, if the crankshaft wear sleeve was removed. Refer to
Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Sat Oct 24 23:42:50 UTC+0800 2020
5/5(W)
w
2020/10/24

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01131265
Crankshaft Gear - Remove and Install
SMCS - 1204-010-GE
Removal Procedure
Table 1
Required Tools
A
1P-0820 Hydraulic Puller 1
9U-6600 Hand Hydraulic Pump 1
0S-2398 Step Plate 1
3H-0468 Puller Plate 4
8B-7549 Puller Leg 2
1B-4207 Full Nut 2
8B-7551 Bearing Puller 1
Start By:
a. Remove the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove".
1/3(W)
w
2020/10/24

1. Use Tool (A) to remove crankshaft gear (1) from crankshaft (2).
Note: Do not remove the gear by tapping with a hammer.
2. Check the key on the crankshaft. If the key is damaged, use a new part for replacement.
NOTICE
Always wear protective gloves when handling parts that have been
heated.
1. Use an oven and heat the crankshaft gear to a temperature of about 100 °C (212 °F). The
crankshaft gear is heated in order to ease installation of the crankshaft gear.
Wear eye protection in order to prevent possible personal injury while
performing the following steps.
2/3(W)
w
2020/10/24

2. Install the crankshaft gear on the end of the crankshaft. Ensure that the key in the crankshaft
is aligned with the keyway in the gear. Tap lightly with a copper hammer until the
crankshaft gear is seated. Ensure that the crankshaft gear is seated against the shoulder on
the crankshaft.
Note: Ensure that the timing marks of the crankshaft gear are on the front.
End By:
a. Install the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Install".
Sat Oct 24 23:43:46 UTC+0800 2020
3/3(W)
w
2020/10/24

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05977048
Bearing Clearance - Check
SMCS - 1203-535; 1219-535
Measurement Procedure
Table 1
Required Tools
A
198-9142
Plastic Gauge (Green)
0.025 to 0.076 mm
(0.001 to 0.003 inch)
1
198-9143
Plastic Gauge (Red)
0.051 to 0.152 mm
(0.002 to 0.006 inch)
1
198-9144
Plastic Gauge (Blue)
0.102 to 0.229 mm
(0.004 to 0.009 inch)
1
198-9145
Plastic Gauge (Yellow)
0.230 to 0.510 mm
(0.009 to 0.020 inch)
1
Note: Plastic gauge may not be necessary when the engine is in the chassis.
NOTICE
1/3(W)
w
2020/10/24

Note: Cat does not recommend the checking of the actual bearing clearances particularly on small
engines. This is because of the possibility of obtaining inaccurate results and the possibility of
damaging the bearing or the journal surfaces. Each Cat engine bearing is quality checked for
specific wall thickness.
Note: The measurements should be within specifications and the correct bearings should be used.
If the crankshaft journals and the bores for the block and the rods were measured during
disassembly, no further checks are necessary. However, if the technician still wants to measure the
bearing clearances, Tooling (A) is an acceptable method. Tooling (A) is less accurate on journals
with small diameters if clearances are less than 0.10 mm (0.004 inch).
NOTICE
Lead wire, shim stock or a dial bore gauge can damage the bearing
surfaces.
The technician must be very careful to use Tooling (A) correctly. The following points must be
remembered:
• Ensure that the backs of the bearings and the bores are clean and dry.
• Ensure that the bearing locking tabs are properly seated in the tab grooves.
• The crankshaft must be free of oil at the contact points of Tooling (A).
1. Put a piece of Tooling (A) on the crown of the bearing that is in the cap.
Note: Do not allow Tooling (A) to extend over the edge of the bearing.
2. Use the correct torque-turn specifications in order to install the bearing cap. Do not use an
impact wrench. Be careful not to dislodge the bearing when the cap is installed.
Note: Do not turn the crankshaft when Tooling (A) is installed.
3. Carefully remove the cap, but do not remove Tooling (A). Measure the width of Tooling
(A) while Tooling (A) is in the bearing cap or on the crankshaft journal. Refer to Illustration
1.
2/3(W)
w
2020/10/24

Typical Example
4. Remove all of Tooling (A) before you install the bearing cap.
Note: When Tooling (A) is used, the readings can sometimes be unclear. For example, all
parts of Tooling (A) are not the same width. Measure the major width in order to ensure that
the parts are within the specification range. Refer to Specifications Manual, "Connecting
Rod Bearing Journal" and Specifications Manual, "Main Bearing Journal" for the correct
clearances.
Sat Oct 24 23:44:42 UTC+0800 2020
3/3(W)
w
2020/10/24

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01569484
Coolant Temperature Switch - Remove and Install
SMCS - 1906-010
Removal Procedure
Personal injury can result from hot coolant, steam and alkali.
At operating temperature, engine coolant is hot and under pressure.
The radiator and all lines to heaters or the engine contain hot coolant or
steam. Any contact can cause severe burns.
Remove cooling system pressure cap slowly to relieve pressure only
when engine is stopped and cooling system pressure cap is cool enough
to touch with your bare hand.
Do not attempt to tighten hose connections when the coolant is hot, the
hose can come off causing burns.
Cooling System Coolant Additive contains alkali. Avoid contact with
skin and eyes.
NOTICE
1/3(W)
w
2020/10/24

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the level of coolant from the radiator below the coolant temperature switch. Drain the
coolant into a suitable container for storage or disposal.
2. Disconnect the electrical connection to the coolant temperature switch.
3. Remove coolant temperature switch (1) from the elbow.
NOTICE
2/3(W)
w
2020/10/24

1. Apply a thin coat of 5P-3413 Pipe Sealant to coolant temperature switch (1) .
2. Install coolant temperature switch (1). Tighten coolant temperature switch (1) to a torque of
7 to 12 N·m (62 to 106 lb in).
3. Reconnect the electrical connection to the coolant temperature switch.
4. Fill the cooling system with coolant to the correct level. Refer to the Operation and
Maintenance Manual, "Refill Capacities" topic for more information.
Sat Oct 24 23:45:38 UTC+0800 2020
3/3(W)
w
2020/10/24

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01569542
Engine Oil Pressure Switch - Remove and Install
SMCS - 1924
Removal Procedure
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Disconnect all electrical connections to the engine oil pressure switch before
proceeding. Mark all connections for later installation.
1/3(W)
w
2020/10/24

Caterpillar cat 320 d rr excavator (prefix fxk) service repair manual (fxk00001 and up)

More Related Content

What's hot (13)

Similar to Caterpillar cat 320 d rr excavator (prefix fxk) service repair manual (fxk00001 and up) (16)

More from fjkskedmme (20)

Recently uploaded (20)

Caterpillar cat 320 d rr excavator (prefix fxk) service repair manual (fxk00001 and up)