Service Repair Manual
Models
320, 320 L, 320 N
AND 320 S
EXCAVATOR
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A S EXCAVATOR 6KM
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 6KM00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928343
Fuel Transfer Pump - Install
SMCS - 1256-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-2998 Lubricant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of the components in the fuel transfer pump, refer to
Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
1/4(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 1 g00623719
1. Lubricate fitting (10) and the bore with clean engine oil. Install the check valve and fitting
(10).
Illustration 2 g00623714
2. Inspect the condition of the O-ring seal. Replace the O-ring seal, if necessary. Install lower
O-ring seal (9).
3. Apply Tooling (A) on the face of lifter (8). Install sleeve assembly (7). Ensure that the flat
on the sleeve aligns with the flat in the bore of the housing.
Illustration 3 g00623687
2/4(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. Lubricate piston (5) with clean engine oil. Install piston (5) and spring (4).
Illustration 4 g00623686
5. Lubricate fitting (3) and the bore for the check valve with clean engine oil. Install the check
valve with the sealing face toward the fitting.
6. Install the O-ring seal and fitting (3).
Illustration 5 g00623671
3/4(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 6 g00623633
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Place cover (1) over spring (4). Install bolts (2) in order to compress spring (4).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 4 15:40:41 UTC+0800 2020
4/4(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A S EXCAVATOR 6KM
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 6KM00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928366
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-5120 Spanner Wrench(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00585831
1. Disconnect the harness assembly (2) from fuel shutoff solenoid (1).
2. Use Tooling (A) to remove the fuel shutoff solenoid from the governor.
3. Remove the O-ring seal from the shutoff solenoid .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-5120 Spanner Wrench(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
2/3(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 2 g00585831
1. Inspect the O-ring seal on the fuel shutoff solenoid. If the O-ring seal is worn or damaged,
use new parts for replacement.
2. Install the O-ring seal on the fuel shutoff solenoid.
3. Install the fuel shutoff solenoid in the governor. Use Tooling (A) and a suitable torque
wrench to tighten the fuel shutoff solenoid to the following torque 30 ± 5 N·m (22 ± 4 lb ft).
4. Connect the harness assembly to the fuel shutoff solenoid.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 4 15:41:37 UTC+0800 2020
3/3(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A S EXCAVATOR 6KM
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 6KM00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928381
Governor - Remove
SMCS - 1264-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
Start By:
a. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 1 g00613041
1. Disconnect the governor control cable.
2. Remove oil tube assembly (1). Remove tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
Illustration 2 g00613071
3. Remove clip (4).
2/5(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 3 g00655975
4. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 4 g00613149
5. Remove the clip and use Tooling (A) to remove the clevis pin (6).
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
3/5(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 5 g00613563
6. Remove bolts (7) and the washers that hold the governor in position.
Illustration 6 g00673182
7. Remove the governor from the engine.
Illustration 7 g00673180
8. Remove O-ring seal (3) on the governor.
Illustration 8 g00672742
4/5(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. Remove the O-ring seal and tube assembly (5) from the cylinder head.
Illustration 9 g00672733
10. Remove O-ring seal (2) on the tube assembly (5).
Illustration 10 g00673178
11. Remove O-ring seal (1) from the cylinder head.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 4 15:42:33 UTC+0800 2020
5/5(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A S EXCAVATOR 6KM
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 6KM00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928419
Governor - Install
SMCS - 1264-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
(1)
This tool is part of the 128-8822 Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
1/5(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 1 g00673178
1. Apply lubricant to the new O-ring seal (1). Install new O-ring seal (1) in the cylinder head.
Illustration 2 g00672733
2. Apply lubricant to the new O-ring seal (2). Install new O-ring seal (2) on the tube assembly
(5).
Illustration 3 g00672742
3. Install the O-ring seal and tube assembly (5) in the cylinder head.
2/5(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 4 g00673180
4. Apply lubricant to the new O-ring seal (3). Install new O-ring seal (3) on the governor.
Illustration 5 g00673182
5. Place the governor in position on the engine.
Illustration 6 g00613563
6. Install the washers and bolts (7) that hold the governor in place.
3/5(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 7 g00672755
7. Install clevis pin (6) in Tooling (B).
Illustration 8 g00672752
8. Use Tooling (B) to install clevis pin (6) and the clip.
9. Check the fuel setting adjustment. Refer to Testing and Adjusting, SENR5118.
4/5(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
Illustration 9 g00655975
10. Use Tooling (A) to slide tube assembly (5) into the governor.
Illustration 10 g00613071
11. Install clip (4).
Illustration 11 g00613041
12. Install oil tube assembly (1). Install tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
13. Install the governor control cable.
End By:
a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 4 15:43:28 UTC+0800 2020
5/5(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A S EXCAVATOR 6KM
Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 6KM00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928445
Fuel Injection Control Linkage - Remove
SMCS - 1298-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers 1
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
Illustration 1 g00613071
1. Remove clip (4). Clip (4) is located between the governor and the cylinder head.
Illustration 2 g00655975
2. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
Illustration 3 g00613149
2/3(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. Remove the clip and use Tooling (A) to remove the clevis pin (6). Clevis pin (6) connects
the governor to the control lever of the fuel injection control linkage.
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
Illustration 4 g00630566
4. Remove bolts (1) and remove fuel injection control linkage (2). Control lever (3) connects
the fuel injection control linkage (2) to the governor.
Note: For information on the inspection procedure for control lever (3), refer to Special
Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection
Control Linkage and the 4P-9048 Fuel Injection Control Linkage".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jan 4 15:44:24 UTC+0800 2020
3/3(W)
w
2020/1/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...

More Related Content

PDF
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 320 N EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 320 EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 an...
PDF
Caterpillar Cat 320 N EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 320 EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 an...
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320 N EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320 EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 an...
Caterpillar Cat 320 N EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320 EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 an...

Similar to Caterpillar Cat 320 N EXCAVATOR (Prefix 6KM) Service Repair Manual (6KM00001 and up).pdf (8)

PDF
Caterpillar Cat 320 EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 an...
PDF
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 320 N EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 320 N EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 320 EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 an...
PDF
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320 EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 an...
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320 N EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320 N EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320 EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 an...
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Ad

More from udjkskmdm3e (20)

PDF
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
PDF
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
PDF
Caterpillar Cat 440 Backhoe Loader (Prefix DC9) Service Repair Manual (DC9000...
PDF
Caterpillar Cat 416 SERIES II BACKHOE LOADER (Prefix 5PC) Service Repair Manu...
PDF
Caterpillar Cat 320D2 Excavator (Prefix WBF) Service Repair Manual (WBF00001 ...
PDF
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...
PDF
Caterpillar Cat 320 L EXCAVATOR (Prefix 4BK) Service Repair Manual (4BK00001 ...
PDF
Caterpillar Cat 320D2 Excavator (Prefix SDZ) Service Repair Manual (SDZ00001 ...
PDF
Caterpillar Cat 320 S EXCAVATOR (Prefix 6KM) Service Repair Manual (6KM00001 ...
PDF
Caterpillar Cat 320 L EXCAVATOR (Prefix 6KM) Service Repair Manual (6KM00001 ...
PDF
Caterpillar Cat 320D Log Loader (Prefix GKS) Service Repair Manual (GKS00001 ...
PDF
Caterpillar Cat 320L TRACK-TYPE EXCAVATOR (Prefix 1TL) Service Repair Manual ...
PDF
Caterpillar Cat 308E2 Mini Hydraulic Excavator (Prefix F8C) Service Repair Ma...
PDF
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 320L EXCAVATOR (Prefix 4ZJ) Service Repair Manual (4ZJ00001-0...
PDF
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
PDF
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...
PDF
CASE SV212 Tier 3 Vibratory Roller Service Repair Manual.pdf
PDF
Caterpillar Cat 320 TRACK-TYPE EXCAVATOR (Prefix 1TL) Service Repair Manual (...
PDF
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...
Caterpillar Cat 430F2 Backhoe Loader (Prefix HWE) Service Repair Manual (HWE0...
Caterpillar Cat 432F2 BACKHOE LOADER (Prefix LYJ) Service Repair Manual (LYJ0...
Caterpillar Cat 440 Backhoe Loader (Prefix DC9) Service Repair Manual (DC9000...
Caterpillar Cat 416 SERIES II BACKHOE LOADER (Prefix 5PC) Service Repair Manu...
Caterpillar Cat 320D2 Excavator (Prefix WBF) Service Repair Manual (WBF00001 ...
Caterpillar Cat 320C U Excavator (Prefix CLM) Service Repair Manual (CLM00001...
Caterpillar Cat 320 L EXCAVATOR (Prefix 4BK) Service Repair Manual (4BK00001 ...
Caterpillar Cat 320D2 Excavator (Prefix SDZ) Service Repair Manual (SDZ00001 ...
Caterpillar Cat 320 S EXCAVATOR (Prefix 6KM) Service Repair Manual (6KM00001 ...
Caterpillar Cat 320 L EXCAVATOR (Prefix 6KM) Service Repair Manual (6KM00001 ...
Caterpillar Cat 320D Log Loader (Prefix GKS) Service Repair Manual (GKS00001 ...
Caterpillar Cat 320L TRACK-TYPE EXCAVATOR (Prefix 1TL) Service Repair Manual ...
Caterpillar Cat 308E2 Mini Hydraulic Excavator (Prefix F8C) Service Repair Ma...
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 320L EXCAVATOR (Prefix 4ZJ) Service Repair Manual (4ZJ00001-0...
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix FJX) Service Repair ...
CASE SV212 Tier 3 Vibratory Roller Service Repair Manual.pdf
Caterpillar Cat 320 TRACK-TYPE EXCAVATOR (Prefix 1TL) Service Repair Manual (...
Caterpillar Cat 320C LU Excavator (Prefix CLM) Service Repair Manual (CLM0000...
Ad

Recently uploaded (20)

PDF
Volvo Dump Truck A40E Service Repair Manual.pdf
PPT
industrialsafetyhazards-180118095222.ppt
PDF
John Deere 5055e ELECTRICAL REPAIR Repair Manual - Tm900319.pdf
PDF
Some briefly information About buying linkedin accounts.pdf
PDF
Bobcat t40140, t40180 telescopic handler service repair manual (sn b33 j11001...
PPTX
Total quality management and I have a great day
PDF
John Deere 410E Articulated Dump Trucks Diagnostic Manuals.pdf
PDF
BOBCAT 442 Excavator Service Repair Manual.pdf
PDF
Bobcat t40140 telescopic handler service repair manual sn b33 j11001 and abov...
PDF
Designyze – Creative Digital Marketing & Design Agency in India
PDF
Pistons Volvo EC160C NL EC160CNL Excavator Service Repair Manual.pdf
PPTX
Air craft and Rescue related ppt which detailed explain about
PPTX
DNA Packaging in Eukaryot ic Cells.pptx
PDF
Deutz D6D EBE2 Volvo EC160BLC Excavator Service Repair Manual.pdf
PDF
D6E Engine Volvo EC160C NL Excavator Service Repair Manual.pdf
PPTX
APQP FOR AUTOMOTIVE AND PPAP FOR SUPPLIER
PDF
D85PX-15E0 Komatsu d85 px 15e0 dozer bulldozer Technical manual.pdf
PDF
Caterpillar Cat 330B L Excavator (Prefix 4RS) Service Repair Manual Instant D...
PPT
157_37315_EA221_2013_1__2_1_Chapter 1, introduction to OR.ppt
PDF
CASE CX45B Series 2 Mini Excavator Service Repair Manual Instant Download.pdf
Volvo Dump Truck A40E Service Repair Manual.pdf
industrialsafetyhazards-180118095222.ppt
John Deere 5055e ELECTRICAL REPAIR Repair Manual - Tm900319.pdf
Some briefly information About buying linkedin accounts.pdf
Bobcat t40140, t40180 telescopic handler service repair manual (sn b33 j11001...
Total quality management and I have a great day
John Deere 410E Articulated Dump Trucks Diagnostic Manuals.pdf
BOBCAT 442 Excavator Service Repair Manual.pdf
Bobcat t40140 telescopic handler service repair manual sn b33 j11001 and abov...
Designyze – Creative Digital Marketing & Design Agency in India
Pistons Volvo EC160C NL EC160CNL Excavator Service Repair Manual.pdf
Air craft and Rescue related ppt which detailed explain about
DNA Packaging in Eukaryot ic Cells.pptx
Deutz D6D EBE2 Volvo EC160BLC Excavator Service Repair Manual.pdf
D6E Engine Volvo EC160C NL Excavator Service Repair Manual.pdf
APQP FOR AUTOMOTIVE AND PPAP FOR SUPPLIER
D85PX-15E0 Komatsu d85 px 15e0 dozer bulldozer Technical manual.pdf
Caterpillar Cat 330B L Excavator (Prefix 4RS) Service Repair Manual Instant D...
157_37315_EA221_2013_1__2_1_Chapter 1, introduction to OR.ppt
CASE CX45B Series 2 Mini Excavator Service Repair Manual Instant Download.pdf

Caterpillar Cat 320 N EXCAVATOR (Prefix 6KM) Service Repair Manual (6KM00001 and up).pdf

  • 1. Service Repair Manual Models 320, 320 L, 320 N AND 320 S EXCAVATOR
  • 2. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320-A S EXCAVATOR 6KM Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 6KM00001-UP (MACHINE) POWERED BY 3116 ENGINE Disassembly and Assembly 446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009 i01928343 Fuel Transfer Pump - Install SMCS - 1256-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 8T-2998 Lubricant 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: For information on reusability of the components in the fuel transfer pump, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines Equipped with Mechanical Unit Injectors (MUI)". 1/4(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 3. Illustration 1 g00623719 1. Lubricate fitting (10) and the bore with clean engine oil. Install the check valve and fitting (10). Illustration 2 g00623714 2. Inspect the condition of the O-ring seal. Replace the O-ring seal, if necessary. Install lower O-ring seal (9). 3. Apply Tooling (A) on the face of lifter (8). Install sleeve assembly (7). Ensure that the flat on the sleeve aligns with the flat in the bore of the housing. Illustration 3 g00623687 2/4(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 4. 4. Lubricate piston (5) with clean engine oil. Install piston (5) and spring (4). Illustration 4 g00623686 5. Lubricate fitting (3) and the bore for the check valve with clean engine oil. Install the check valve with the sealing face toward the fitting. 6. Install the O-ring seal and fitting (3). Illustration 5 g00623671 3/4(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 5. Illustration 6 g00623633 Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. 7. Place cover (1) over spring (4). Install bolts (2) in order to compress spring (4). Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Jan 4 15:40:41 UTC+0800 2020 4/4(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 6. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320-A S EXCAVATOR 6KM Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 6KM00001-UP (MACHINE) POWERED BY 3116 ENGINE Disassembly and Assembly 446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009 i01928366 Fuel Shutoff Solenoid - Remove and Install SMCS - 1259-010 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 9U-5120 Spanner Wrench(1) 1 (1) This tool is part of the 128-8822 Fuel System and Governor Tool Group. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. 1/3(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 7. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. Illustration 1 g00585831 1. Disconnect the harness assembly (2) from fuel shutoff solenoid (1). 2. Use Tooling (A) to remove the fuel shutoff solenoid from the governor. 3. Remove the O-ring seal from the shutoff solenoid . Installation Procedure Table 2 Required Tools Tool Part Number Part Description Qty A 9U-5120 Spanner Wrench(1) 1 (1) This tool is part of the 128-8822 Fuel System and Governor Tool Group. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE 2/3(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 8. Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. Illustration 2 g00585831 1. Inspect the O-ring seal on the fuel shutoff solenoid. If the O-ring seal is worn or damaged, use new parts for replacement. 2. Install the O-ring seal on the fuel shutoff solenoid. 3. Install the fuel shutoff solenoid in the governor. Use Tooling (A) and a suitable torque wrench to tighten the fuel shutoff solenoid to the following torque 30 ± 5 N·m (22 ± 4 lb ft). 4. Connect the harness assembly to the fuel shutoff solenoid. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Jan 4 15:41:37 UTC+0800 2020 3/3(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 9. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320-A S EXCAVATOR 6KM Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 6KM00001-UP (MACHINE) POWERED BY 3116 ENGINE Disassembly and Assembly 446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009 i01928381 Governor - Remove SMCS - 1264-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 136-4149 Governor Pliers(1) 1 (1) This tool is part of the 128-8822 Fuel System and Governor Tool Group. Start By: a. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff Solenoid - Remove and Install". NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. 1/5(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 10. Illustration 1 g00613041 1. Disconnect the governor control cable. 2. Remove oil tube assembly (1). Remove tube assembly (2) and tube assembly for fuel ratio control (3), if equipped. Plug and cap all connections. Illustration 2 g00613071 3. Remove clip (4). 2/5(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 11. Illustration 3 g00655975 4. Use Tooling (A) to slide tube assembly (5) into the cylinder head. Illustration 4 g00613149 5. Remove the clip and use Tooling (A) to remove the clevis pin (6). Note: Clevis pin (6) must stay with the governor in order to be adjusted. 3/5(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 12. Illustration 5 g00613563 6. Remove bolts (7) and the washers that hold the governor in position. Illustration 6 g00673182 7. Remove the governor from the engine. Illustration 7 g00673180 8. Remove O-ring seal (3) on the governor. Illustration 8 g00672742 4/5(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 13. 9. Remove the O-ring seal and tube assembly (5) from the cylinder head. Illustration 9 g00672733 10. Remove O-ring seal (2) on the tube assembly (5). Illustration 10 g00673178 11. Remove O-ring seal (1) from the cylinder head. Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, & 3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326 Governor Calibration Bench. For information on reusability of components in the governor, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines Equipped with Mechanical Unit Injectors (MUI)". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Jan 4 15:42:33 UTC+0800 2020 5/5(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 14. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320-A S EXCAVATOR 6KM Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 6KM00001-UP (MACHINE) POWERED BY 3116 ENGINE Disassembly and Assembly 446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009 i01928419 Governor - Install SMCS - 1264-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 136-4149 Governor Pliers(1) 1 B 128-8827 Pin(1) 1 1U-7523 Pin Pilot(1) 1 (1) This tool is part of the 128-8822 Governor Tool Group. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, & 3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326 Governor Calibration Bench. For information on reusability of components in the governor, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines Equipped with Mechanical Unit Injectors (MUI)". 1/5(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 15. Illustration 1 g00673178 1. Apply lubricant to the new O-ring seal (1). Install new O-ring seal (1) in the cylinder head. Illustration 2 g00672733 2. Apply lubricant to the new O-ring seal (2). Install new O-ring seal (2) on the tube assembly (5). Illustration 3 g00672742 3. Install the O-ring seal and tube assembly (5) in the cylinder head. 2/5(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 16. Illustration 4 g00673180 4. Apply lubricant to the new O-ring seal (3). Install new O-ring seal (3) on the governor. Illustration 5 g00673182 5. Place the governor in position on the engine. Illustration 6 g00613563 6. Install the washers and bolts (7) that hold the governor in place. 3/5(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 17. Illustration 7 g00672755 7. Install clevis pin (6) in Tooling (B). Illustration 8 g00672752 8. Use Tooling (B) to install clevis pin (6) and the clip. 9. Check the fuel setting adjustment. Refer to Testing and Adjusting, SENR5118. 4/5(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 18. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
  • 19. Illustration 9 g00655975 10. Use Tooling (A) to slide tube assembly (5) into the governor. Illustration 10 g00613071 11. Install clip (4). Illustration 11 g00613041 12. Install oil tube assembly (1). Install tube assembly (2) and tube assembly for fuel ratio control (3), if equipped. Plug and cap all connections. 13. Install the governor control cable. End By: a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff Solenoid - Remove and Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Jan 4 15:43:28 UTC+0800 2020 5/5(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 20. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 320-A S EXCAVATOR 6KM Configuration: 320, 320 L, 320 N AND 320 S EXCAVATORS 6KM00001-UP (MACHINE) POWERED BY 3116 ENGINE Disassembly and Assembly 446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009 i01928445 Fuel Injection Control Linkage - Remove SMCS - 1298-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 136-4149 Governor Pliers 1 Start By: a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove". NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1/3(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 21. Illustration 1 g00613071 1. Remove clip (4). Clip (4) is located between the governor and the cylinder head. Illustration 2 g00655975 2. Use Tooling (A) to slide tube assembly (5) into the cylinder head. Illustration 3 g00613149 2/3(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
  • 22. 3. Remove the clip and use Tooling (A) to remove the clevis pin (6). Clevis pin (6) connects the governor to the control lever of the fuel injection control linkage. Note: Clevis pin (6) must stay with the governor in order to be adjusted. Illustration 4 g00630566 4. Remove bolts (1) and remove fuel injection control linkage (2). Control lever (3) connects the fuel injection control linkage (2) to the governor. Note: For information on the inspection procedure for control lever (3), refer to Special Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control Linkage and the 4P-9048 Fuel Injection Control Linkage". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Sat Jan 4 15:44:24 UTC+0800 2020 3/3(W) w 2020/1/4 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...