Caterpillar Cat 320D2 Excavator (Prefix NBF) Service Repair Manual (NBF00001 and up).pdf

Service Repair Manual
Models
320D2 Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D2 EXCAVATOR NBF
Configuration: 320D2 & 320D2 L Excavators NBF00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 (Mech) Engines for Caterpillar Built Machines
Media Number -UENR0674-08 Publication Date -01/06/2015 Date Updated -23/01/2017
i04780456
Fuel Injection Pump Gear - Install
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-7336 Crankshaft Turning Tool 1
A(2)
5P-7305 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft ) 1
C
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The fuel injection pump must remain locked until the procedure instructs you to unlock the
fuel injection pump.
1/8(W)
w
2020/2/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Illustration 1 g02697876
1. If necessary, use Tooling (A) to ensure that number one piston is at top dead center on the
compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top
Center Position for No.1 Piston".
2. Ensure that Tooling (C) is installed in Hole (Y) in the cylinder block. Use Tooling (C) in
order to lock the crankshaft in the correct position.
2/8(W)
w
2020/2/20

https://www.aservicemanualpdf.com/
My Dear Friend! Thank you very
much for visiting. Full manual if
required, please enter the
following URL into your browser.
https://www.aservicemanualpdf.com/

3. Ensure that Tooling (B) is installed into Hole (X) in camshaft gear (1).
4. Ensure that shaft (10) of the fuel injection pump is clean and free from damage.
5. Ensure that the fuel injection pump is locked in the correct position. Refer to Disassembly
and Assembly, "Fuel Injection Pump - Install".
6. Ensure that the fuel pump gear is clean and free from wear of damage. If necessary, replace
the fuel pump gear.
3/8(W)
w
2020/2/20

7. Install fuel pump gear (2) to shaft (10) of the fuel injection pump. Ensure that the timing
marks on gear (1), gear (2), and gear (9) are in alignment and that the mesh of the gears is
correct.
4/8(W)
w
2020/2/20

5/8(W)
w
2020/2/20

With Electronic Governor
6/8(W)
w
2020/2/20

With Boost Control
8. Install a new spring washer (11) and install nut (8) to shaft (10) of the fuel injection pump.
Apply sufficient pressure to fuel injection pump gear (2) in a counterclockwise direction in
order to remove the backlash. Tighten nut (8) to a torque of 24 N·m (212 lb in).
9. In order to unlock fuel injection pump (7), loosen locking bolt (5) in the fuel injection
pump. Slide spacer (6) into unlock position. Tighten locking bolt (5) against the spacer to a
torque of 12 N·m (106 lb in). The spacer will prevent the locking bolt from tightening
against the shaft of the fuel injection pump.
10. Remove Tooling (B) and Tooling (C).
11. Tighten nut (8) to a torque of 90 N·m (66 lb ft).
12. Ensure that the backlash for gear (1), gear (2) and gear (9) is within specified values. Refer
to the Specifications, "Gear Group (Front)" for further information.
7/8(W)
w
2020/2/20

13. Install a new O-ring seal (3) to plug (4). Install plug (4) to the cylinder block. Tighten plug
(4) to a torque of 21 N·m (186 lb in).
14. Lubricate the teeth of the gears with clean engine oil.
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Feb 20 22:37:38 UTC+0800 2020
8/8(W)
w
2020/2/20

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07432260
Fuel Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
A - Laser 4044 Fuel Injector Puller 1
B 422-7170 Capping Kit 1
Start By:
a. Remove the fuel injection lines.
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/3(W)
w
2020/2/20

before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Disconnect hose assembly (1) and hose (3) from fuel injector (2).
2. Use Tooling (B) to plug fuel injector (2).
3. Remove bolt (4) and clamp (5) from fuel injector (2).
4. Use Tooling (A) to remove fuel injector (2) from the cylinder head. Remove fuel injector
(2).
5. Remove O-ring seal (6) and seat washer (7) from fuel injector (2).
6. If necessary, repeat Step 1 through Step 5 to remove the remaining fuel injectors.
Thu Feb 20 22:38:34 UTC+0800 2020
2/3(W)
w
2020/2/20

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07432337
Fuel Injector - Install
SMCS - 1290-012
NOTICE
1/2(W)
w
2020/2/20

1. Ensure that the seat for fuel injector (2) in the cylinder head and fuel injector (2) is clean
and free from damage.
2. On installing original fuel injector (2), install a new O-ring seal (6) and a new sealing
washer (7) to fuel injector (2).
On installing a new fuel injector, ensure that O-ring seal (6) and sealing washer (7) are not
damaged and are in place.
Note: Do not lubricate the O-ring seal.
3. Position clamp (5) onto fuel injector (2). Install fuel injector (2) into the cylinder head.
Note: Ensure that alignment Pin (8) is located opposite to clamp (5).
4. Install bolt (4) finger tight.
5. Tighten bolt (4) to a torque of 27 N·m (239 lb in).
6. Remove caps from fuel injector (2).
7. Connect hose assembly (1) and hose (3) to fuel injector (2).
8. If necessary, repeat Step 1 through Step 7 to install the remaining fuel injector.
End By:
a. Install the fuel injection lines.
Thu Feb 20 22:39:30 UTC+0800 2020
2/2(W)
w
2020/2/20

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i04780487
Turbocharger - Remove - Side Mounted Turbocharger
SMCS - 1052-011
Removal Procedure
NOTICE
NOTICE
containing fluids.
Note: Plug and cap all open ports and tube assemblies.
1/4(W)
w
2020/2/20

1. Loosen hose clamp (2) and disconnect hose assembly (1) from turbocharger (4).
2. Loosen hose clamp (3) and disconnect tube assembly (5) from turbocharger (4).
3. If necessary, remove the hose assembly from the wastegate actuator on the turbocharger.
4. Remove the exhaust out tube assembly from the turbocharger, refer to the Original
Equipment Manufactures (OEM) for the correct procedure.
5. If necessary, remove the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust
Elbow - Remove and Install" for the correct procedure.
2/4(W)
w
2020/2/20

6. Remove banjo bolt (7) from tube assembly (10). Remove sealing washers (6) (not shown).
7. Remove bolt (11) from tube assembly (10). Remove tube assembly (10) from turbocharger
(4) and the cylinder block.
8. Remove O-ring seal (12) (not shown) from tube assembly (10).
9. Remove bolts (9) from tube assembly (14). Remove bolts (13) from tube assembly (14).
10. Remove tube assembly (14) from turbocharger (4) and the cylinder block.
11. Remove gasket (8) (not shown) and gasket (15) (not shown).
3/4(W)
w
2020/2/20

12. Remove nuts (18) from turbocharger (4). Remove turbocharger (4) from exhaust manifold
(16).
Note: Ensure that the weight of the turbocharger is supported as the nuts are removed.
13. If necessary, remove studs (17) from exhaust manifold (16).
Thu Feb 20 22:40:25 UTC+0800 2020
4/4(W)
w
2020/2/20

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i04780488
Turbocharger - Remove - Turbocharger Top Mounted
SMCS - 1052-011
Removal Procedure
NOTICE
NOTICE
containing fluids.
Note: Plug and cap all open ports and tube assemblies.
1. Loosen the hose clamps and disconnect the hose assembly from the turbocharger inlet.
2. Loosen the hose clamps and disconnect the hose assembly from the turbocharger outlet.
3. If necessary, remove the hose assembly from the wastegate actuator on the turbocharger.
1/4(W)
w
2020/2/20

4. Remove the exhaust out tube assembly from the turbocharger, refer to the Original
Equipment Manufactures (OEM) for the correct procedure.
5. If necessary, remove the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust
Elbow - Remove and Install" for the correct procedure.
Typical example
6. Remove banjo bolt (1) and remove sealing washers (2) from tube assembly (10).
7. Remove bolts (6) from tube assembly (9). Remove gasket (5).
2/4(W)
w
2020/2/20

8. Remove the tube clamps from tube assembly (9) and tube assembly (10). Position tube
assembly (10) away from turbocharger (4).
9. Remove nuts (3) from turbocharger (4).
10. Remove turbocharger (4) from exhaust manifold (8).
11. If necessary, remove studs (7) from exhaust manifold (8).
Typical example
12. In order to remove tube assembly (9) and tube assembly (10) the removal of exhaust
manifold (8) will be necessary.
13. Remove bolt (13) from tube clips (12) and remove spacer (11).
3/4(W)
w
2020/2/20

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

14. Remove bolt (15) from tube assembly (10). Disconnect tube assembly (10) from the
cylinder block.
15. Remove bolts (17) from tube assembly (9). Remove gasket (16).
16. Remove exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold (Top
Mounted Turbo Charger Exhaust Manifold) - Remove and Install" for the correct procedure.
17. Remove tube assembly (9) and tube assembly (10). Remove O-ring seal (14) from tube
assembly (10).
Thu Feb 20 22:41:21 UTC+0800 2020
4/4(W)
w
2020/2/20

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i04780484
Turbocharger - Install - Side Mounted Turbocharger
SMCS - 1052-012
Table 1
Required Tools
A 5P-3975 Rubber Lubricant 1
NOTICE
1/5(W)
w
2020/2/20

Caterpillar Cat 320D2 Excavator (Prefix NBF) Service Repair Manual (NBF00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 320D2 Excavator (Prefix NBF) Service Repair Manual (NBF00001 and up).pdf (20)

More from iphg8793466 (20)

Recently uploaded (20)

Caterpillar Cat 320D2 Excavator (Prefix NBF) Service Repair Manual (NBF00001 and up).pdf