Caterpillar cat 322 b l excavator (prefix 1as) service repair manual (1as00001 and up)

Service Repair Manual
Models
322B L EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322B L EXCAVATOR 1AS
Configuration: 322B L TRACK-TYPE EXCAVATOR /HAMMER ARRANGEMENT/ 1AS00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F
Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel
Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928381
Governor - Remove
SMCS - 1264-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
Start By:
a. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff Solenoid -
Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5322B L TRACK-TYPE EXCAVATOR /HAMMER ARRANGEMENT/ 1AS00001-U...
2019/10/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g00613041
1. Disconnect the governor control cable.
2. Remove oil tube assembly (1). Remove tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
3. Remove clip (4).

4. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
5. Remove the clip and use Tooling (A) to remove the clevis pin (6).
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
6. Remove bolts (7) and the washers that hold the governor in position.
7. Remove the governor from the engine.

8. Remove O-ring seal (3) on the governor.
9. Remove the O-ring seal and tube assembly (5) from the cylinder head.
10. Remove O-ring seal (2) on the tube assembly (5).

11. Remove O-ring seal (1) from the cylinder head.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326 Governor
Calibration Bench. For information on reusability of components in the governor, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection and General
Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines Equipped with
Mechanical Unit Injectors (MUI)".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 24 08:51:05 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Loaders
i01928419
Governor - Install
SMCS - 1264-012
Installation Procedure
Table 1
Required Tools
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
(1)
This tool is part of the 128-8822 Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326 Governor
Calibration Bench. For information on reusability of components in the governor, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection and General
Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines Equipped with
Mechanical Unit Injectors (MUI)".

1. Apply lubricant to the new O-ring seal (1). Install new O-ring seal (1) in the cylinder head.
2. Apply lubricant to the new O-ring seal (2). Install new O-ring seal (2) on the tube assembly (5).
3. Install the O-ring seal and tube assembly (5) in the cylinder head.

4. Apply lubricant to the new O-ring seal (3). Install new O-ring seal (3) on the governor.
5. Place the governor in position on the engine.
6. Install the washers and bolts (7) that hold the governor in place.

7. Install clevis pin (6) in Tooling (B).
8. Use Tooling (B) to install clevis pin (6) and the clip.
9. Check the fuel setting adjustment. Refer to Testing and Adjusting, SENR5118.

10. Use Tooling (A) to slide tube assembly (5) into the governor.
11. Install clip (4).
12. Install oil tube assembly (1). Install tube assembly (2) and tube assembly for fuel ratio control
(3), if equipped. Plug and cap all connections.
13. Install the governor control cable.
End By:
a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff Solenoid -
Remove and Install".
Thu Oct 24 08:52:01 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Loaders
i01928445
Fuel Injection Control Linkage - Remove
SMCS - 1298-011
Removal Procedure
Table 1
Required Tools
A 136-4149 Governor Pliers 1
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.

1. Remove clip (4). Clip (4) is located between the governor and the cylinder head.
2. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
3. Remove the clip and use Tooling (A) to remove the clevis pin (6). Clevis pin (6) connects the
governor to the control lever of the fuel injection control linkage.

Note: Clevis pin (6) must stay with the governor in order to be adjusted.
4. Remove bolts (1) and remove fuel injection control linkage (2). Control lever (3) connects the
fuel injection control linkage (2) to the governor.
Note: For information on the inspection procedure for control lever (3), refer to Special
Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control
Linkage and the 4P-9048 Fuel Injection Control Linkage".
Thu Oct 24 08:52:57 UTC+0800 2019

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders
i01928573
Fuel Injection Control Linkage - Install
SMCS - 1298-012
Installation Procedure
Table 1
Required Tools
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
C 1U-6675 Spring Compressor(1)
6
D 128-8822 Fuel System and Governor Tool Gp 1
(1)
This tool is part of the 128-8822 Governor Tool Group.

Note: For information on the inspection procedure for control lever (3), refer to Special Instruction,
REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control Linkage and the 4P
-9048 Fuel Injection Control Linkage".
1. Loosen setscrews (4) on each bracket.
2. Install fuel control linkage (2) and install bolts (1). Use the following sequence in order to tighten the
bolts.
3. Tighten bracket (A) and (D) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
4. Tighten brackets (B) and (C) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
5. Position brackets (B) and (C) in order to allow free rotation of the fuel control rod.
6. Use a 2.5 mm (0.10 inch) wrench to tighten setscrews (4). Tighten the setscrews to a torque of
3.5 ± 0.2 N·m (31 ± 2 lb in). Do not overtighten the setscrews. Ensure that the control rod rotates
freely.
7. The control rod should rotate freely when a force of 4.4 N (1 lb) or less is applied to control lever
(3).
8. Rotate the unit injectors in order to engage the injector rack bar (5) with the fuel injection control
linkage (2).
Note: If the unit injectors are not installed, refer to the Disassembly and Assembly, "Unit Injector -
Install".

9. Install Tooling (C) on the unit injectors and compress the springs.
Note: For the procedure to install Tooling (C), refer to Tool Operating Manual, NEHS0610, "Using
the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
10. Install clevis pin (6) in Tooling (B). Clevis pin (6) attaches the control lever (3) to the governor.
11. Use Tooling (B) to install clevis pin (6) and the clip.
12. Use Tooling (D) to set the unit injector synchronization.
Note: For the procedure to use Tooling (D), refer to Tool Operating Manual, NEHS0610, "Using the
128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
13. Remove Tooling (C) from the unit injectors.

Caterpillar cat 322 b l excavator (prefix 1as) service repair manual (1as00001 and up)

More Related Content

More from ufjjsjekkeidol (20)

Recently uploaded (20)

Caterpillar cat 322 b l excavator (prefix 1as) service repair manual (1as00001 and up)