Caterpillar cat 322 ln excavator (prefix 8 ml) service repair manual (8ml00001 and up)

Service Repair Manual
Model
322 L, 322 LN AND
322 N EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322 L EXCAVATOR 8ML
Configuration: 322 L, 322 LN AND 322 N EXCAVATORS 8ML00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928381
Governor - Remove
SMCS - 1264-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 136-4149 Governor Pliers(1)
1
(1)
This tool is part of the 128-8822 Fuel System and Governor Tool Group.
Start By:
a. Remove the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/5322 L, 322 LN AND 322 N EXCAVATORS 8ML00001-UP (MACHINE) POWERE...
2019/10/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g00613041
1. Disconnect the governor control cable.
2. Remove oil tube assembly (1). Remove tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
3. Remove clip (4).

4. Use Tooling (A) to slide tube assembly (5) into the cylinder head.
5. Remove the clip and use Tooling (A) to remove the clevis pin (6).
Note: Clevis pin (6) must stay with the governor in order to be adjusted.

6. Remove bolts (7) and the washers that hold the governor in position.
7. Remove the governor from the engine.
8. Remove O-ring seal (3) on the governor.

9. Remove the O-ring seal and tube assembly (5) from the cylinder head.
10. Remove O-ring seal (2) on the tube assembly (5).
11. Remove O-ring seal (1) from the cylinder head.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 15 15:51:40 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01928419
Governor - Install
SMCS - 1264-012
Installation Procedure
Table 1
Required Tools
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
(1)
This tool is part of the 128-8822 Governor Tool Group.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For more information on the governor, refer to Service Manual, SENR6454, "3114, 3116, &
3126 Engine Governors". The Service Manual, SENR6454 requires the use of a 1U-7326
Governor Calibration Bench. For information on reusability of components in the governor, refer
to Guideline For Reusable Parts And Salvage Operations, SEBF8434, "3100 Governor Inspection
and General Information for Mechanical Governor Groups Used in 3114, 3116, and 3126 Engines
Equipped with Mechanical Unit Injectors (MUI)".

1. Apply lubricant to the new O-ring seal (1). Install new O-ring seal (1) in the cylinder head.
2. Apply lubricant to the new O-ring seal (2). Install new O-ring seal (2) on the tube assembly
(5).
3. Install the O-ring seal and tube assembly (5) in the cylinder head.

4. Apply lubricant to the new O-ring seal (3). Install new O-ring seal (3) on the governor.
5. Place the governor in position on the engine.
6. Install the washers and bolts (7) that hold the governor in place.

7. Install clevis pin (6) in Tooling (B).
8. Use Tooling (B) to install clevis pin (6) and the clip.
9. Check the fuel setting adjustment. Refer to Testing and Adjusting, SENR5118.

10. Use Tooling (A) to slide tube assembly (5) into the governor.
11. Install clip (4).
12. Install oil tube assembly (1). Install tube assembly (2) and tube assembly for fuel ratio
control (3), if equipped. Plug and cap all connections.
13. Install the governor control cable.
End By:
a. Install the fuel shutoff solenoid. Refer to Disassembly and Assembly, "Fuel Shutoff
Solenoid - Remove and Install".
Tue Oct 15 15:52:36 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01928445
Fuel Injection Control Linkage - Remove
SMCS - 1298-011
Removal Procedure
Table 1
Required Tools
A 136-4149 Governor Pliers 1
Start By:
a. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE

1. Remove clip (4). Clip (4) is located between the governor and the cylinder head.
2. Use Tooling (A) to slide tube assembly (5) into the cylinder head.

3. Remove the clip and use Tooling (A) to remove the clevis pin (6). Clevis pin (6) connects
the governor to the control lever of the fuel injection control linkage.
Note: Clevis pin (6) must stay with the governor in order to be adjusted.
4. Remove bolts (1) and remove fuel injection control linkage (2). Control lever (3) connects
the fuel injection control linkage (2) to the governor.
Note: For information on the inspection procedure for control lever (3), refer to Special
Instruction, REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection
Control Linkage and the 4P-9048 Fuel Injection Control Linkage".
Tue Oct 15 15:53:32 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F
Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders
i01928573
Fuel Injection Control Linkage - Install
SMCS - 1298-012
Table 1
Required Tools
1
B
128-8827 Pin(1)
1
1U-7523 Pin Pilot(1)
1
C 1U-6675 Spring Compressor(1)
6
D 128-8822 Fuel System and Governor Tool Gp 1
(1)
This tool is part of the 128-8822 Governor Tool Group.

Note: For information on the inspection procedure for control lever (3), refer to Special Instruction,
REHS0601, "Inspection and Modification of the 102-7459 Fuel Injection Control Linkage and the 4P
-9048 Fuel Injection Control Linkage".
1. Loosen setscrews (4) on each bracket.
2. Install fuel control linkage (2) and install bolts (1). Use the following sequence in order to tighten the
bolts.
3. Tighten bracket (A) and (D) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
4. Tighten brackets (B) and (C) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
5. Position brackets (B) and (C) in order to allow free rotation of the fuel control rod.
6. Use a 2.5 mm (0.10 inch) wrench to tighten setscrews (4). Tighten the setscrews to a torque of
3.5 ± 0.2 N·m (31 ± 2 lb in). Do not overtighten the setscrews. Ensure that the control rod rotates
freely.
7. The control rod should rotate freely when a force of 4.4 N (1 lb) or less is applied to control lever
(3).
8. Rotate the unit injectors in order to engage the injector rack bar (5) with the fuel injection control
linkage (2).
Note: If the unit injectors are not installed, refer to the Disassembly and Assembly, "Unit Injector -
Install".

9. Install Tooling (C) on the unit injectors and compress the springs.
Note: For the procedure to install Tooling (C), refer to Tool Operating Manual, NEHS0610, "Using
the 128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
10. Install clevis pin (6) in Tooling (B). Clevis pin (6) attaches the control lever (3) to the governor.
11. Use Tooling (B) to install clevis pin (6) and the clip.
12. Use Tooling (D) to set the unit injector synchronization.
Note: For the procedure to use Tooling (D), refer to Tool Operating Manual, NEHS0610, "Using the
128-8822 Tool Group on 3114, 3116, and 3126 Engines with Mechanical Unit Injectors (MUI)".
13. Remove Tooling (C) from the unit injectors.

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

14. Use Tooling (A) to slide tube assembly (5) into the governor.
15. Install clip (4).
End By:
a. Install the rocker arm assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Install".
Tue Oct 15 15:54:27 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i05919358
Unit Injector - Remove
SMCS - 1290-011
Removal Procedure
Table 1
Required Tools
A 5P-0302 Bar 1
Start By:
A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers

before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.

1. Remove fuel injector hold-down bolt (1) .
Note: Do not pry on the injector hold-down bracket. Damage to the unit injector could
occur. The unit injector has a notch on the opposite side of the rack. This notch is used for
prying the unit injector loose. Some fuel injector racks move freely when the spring is not
compressed. Do not move the fuel injector rack without compressing the fuel injector spring
slightly. Damage may occur to the unit injector.
2. Use Tooling (A) to loosen the unit injector. Rotate the unit injector in order to disengage
injector rack bar (3) from fuel injection control linkage (2) .
3. Remove the unit injector. Ensure that two O-ring seals are on the unit injector.
Tue Oct 15 15:55:23 UTC+0800 2019

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i05919370
Unit Injector - Install
SMCS - 1290-012
Table 1
Required Tools
B 4C-5553 Injector Seat Cleaning Brush 1
C 173-1530 Injector Seating Tool 1
D 143-2099 Unit Injector Tool Group (Sleeve Replacement) 1
NOTICE
1. Inspect the unit injector sleeve for pitting and for carbon tracking. Used unit injector sleeves
do not need to be reamed unless the seated area is pitted or eroded. If the seated area has
excessive carbon deposits, the used unit injector sleeves need to be reamed. Refer to Tool
Operating Manual, NEHS0675, "Using the 143-2099 Sleeve Replacement Tool Group on
3114, 3116, and 3126 Engines". Use Tooling (D) to ream injector sleeves.
2. Inspect the condition of the O-ring seals on the unit injector. Replace the seals, if necessary.

Caterpillar cat 322 ln excavator (prefix 8 ml) service repair manual (8ml00001 and up)

More Related Content

Similar to Caterpillar cat 322 ln excavator (prefix 8 ml) service repair manual (8ml00001 and up) (18)

More from fujsjexswfksekmfm (20)

Recently uploaded (20)

Caterpillar cat 322 ln excavator (prefix 8 ml) service repair manual (8ml00001 and up)