Caterpillar Cat 322C Excavator (Prefix DAA) Service Repair Manual (DAA00001 and up).pdf

Service Repair Manual
Model
322C and 322C L 322CL Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR DAA
Configuration: 322C & 322C L Excavators DAA00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
322C Excavator Machine Systems
Media Number -RENR3843-07 Publication Date -01/02/2017 Date Updated -20/02/2017
i02566235
Pilot Valve (Joystick) - Disassemble
SMCS - 5059-015
Disassembly Procedure
Start By:
a. Remove the pilot valve. Refer to Disassembly and Assembly, "Pilot Valve (Joystick) -
Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will prevent dirt from entering the internal
mechanism.
1/6
322C & 322C L Excavators DAA00001-UP (MACHINE) POWERED BY 3126 Engin...
2019/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g00741704
Spool assembly (17) is installed in port (1) and port (3) in the pilot valve.
Spring seat (7) is installed in port (1) and port (3) in the pilot valve.
1. Remove rubber boot (4) from the pilot valve.
2/6
2019/9/15

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. Measure Distance (A) from the top of plate (12) to the top of plate (20). Record Dimension (a)
for assembly purposes.
3. Tighten nut (8) against plate (12). Remove plate (12), nut (8), and U-joint (14).
Note: If U-joint (14) or plate (12) is not being replaced, do not remove plate (12) from U-joint
(14).
4. Remove nut (8) from U-joint (14).
5. Remove plate (12) from U-joint (14).
6. Remove plate (20) from the pilot valve.
3/6
2019/9/15

Note: The spring seat and the spring may fall out of the rod while you remove the plug.
Note: Mark the seat and the spring for assembly purposes. Spring seat (7) is installed in port
(1) and port (3) in the pilot valve. Spring seat (10) is installed in port (2) and port (4) in the
pilot valve.
7. Remove plug (2) from the pilot valve.
8. Remove spring seat (7) or (10) and spring (6) from rod (5).
9. Remove rod (5) from plug (2).
10. Remove O-ring seal (3) from plug (2).
11. Remove seal (1) from plug (2).
Note: Spool assembly (17) is installed in Port (1) and Port (3) in the pilot valve. Spool
assembly (18) is installed in Port (2) and Port (4) in the pilot valve.
4/6
2019/9/15

12. Remove the spool assembly from the pilot valve.
13. Use the following procedure to disassemble the spool assembly.
Note: Spool (22) is assembled in Port (1) and Port (3) in the pilot valve. Spool (23) is
assembled in Port (2) and Port (4) in the pilot valve.
a. Apply pressure to seat (11) by hand. Put the end of the spool in the slotted opening of
seat (11). Remove seat (11).
Note: Spring (13) is installed on spool (22). Spring (15) is installed on spool (23).
b. Remove spring (13) or spring (15) from the spool.
c. Remove washer (19) from the spool.
14. Remove spring (26) from the pilot valve.
15. Repeat Steps 7 through 14 in order to remove the other three spool assemblies.
5/6
2019/9/15

16. Remove bolts (28) and washers (27).
17. Remove plate (25) from the pilot valve.
18. Remove spring pin (24) from plate (25).
19. Remove O-ring seal (21) from valve body (9).
20. Remove bushing (16) from valve body (9).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Sep 15 18:38:28 UTC+0800 2019
6/6
2019/9/15

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02566243
Pilot Valve (Joystick) - Assemble
SMCS - 5059-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6396 O-Ring Assembly Compound 1
B 9S-3263 Thread Lock Compound 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in
cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint
may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn
or damaged, use new parts for replacement. All disassembly and all assembly procedures must be
performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts covered and
protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring seal may not have the
same sealing properties as a new O-ring seal. Use Tooling (A) during the assembly procedure.
1/7
2019/9/15

2/7
2019/9/15

1. Install bushing (16) in valve body (9).
2. Install new O-ring seal (21) on valve body (9).
3. Install spring pin (24) in plate (25).
Note: Make sure that spring pin (24) is installed in the correct location in the valve body.
4. Install plate (25) on the pilot valve.
5. Install washers (27) and bolts (28). Tighten bolts (28) to a torque of 21 ± 2 N·m (16 ± 1 lb ft).
3/7
2019/9/15

Note: Three different springs are available for the pilot valve. See Table 2.
6. Install spring (26) in the pilot valve.
Table 2
Spring
165-9461(1)
190-7750(2)
190-7751(3)
(1)
Standard spring
(2)
This spring reduces the operating torque by seventy percent.
(3)
This spring reduces the operating torque by eighty percent.
7. Use the following procedure to assemble spool assemblies (17) and (18).
4/7
2019/9/15

Note: Spool (22) is assembled in Port (1) and Port (3) in the pilot valve. Spool (23) is
assembled in Port (2) and Port (4) in the pilot valve.
a. Install washer (19) on the spool.
Note: Spring (13) is installed on spool (22). Spring (15) is installed on spool (23).
b. Install spring (13) or spring (15) on the spool.
c. Put the end of the spool in the slotted opening of seat (11). Install seat (11).
Note: Spool assembly (17) is installed in Port (1) and Port (3) in the pilot valve. Spool
assembly (18) is installed in Port (2) and Port (4) in the pilot valve.
8. Install spool assembly (18) in the pilot valve.
9. Install new seal (1) in plug (2).
10. Install new O-ring seal (3) on plug (2).
11. Install rod (5) in plug (2).
Note: Spring seat (7) is installed in Port (1) and Port (3) in the pilot valve. Spring seat (10) is
installed in Port (2) and Port (4) in the pilot valve.
12. Install spring (6) and the correct spring seat in rod (5).
Note: Make sure that spring seat (7) or (10) and the spring do not fall out of the rod while you
install the plug.
13. Install plug (2) in the pilot valve.
14. Repeat Steps 6 through 13 in order to install the other three spool assemblies.
5/7
2019/9/15

15. Install plate (20) on the pilot valve.
16. Apply Tooling (B) on the threads on the upper half of U-joint (14).
17. Install plate (12) on U-joint (14).
18. Install nut (8) on U-joint (14).
19. Tighten nut (8) against plate (12).
20. Install plate (12), nut (8), and U-joint (14). Tighten U-joint (14) to a torque of 47 ± 3 N·m
(35 ± 2 lb ft).
6/7
2019/9/15

21. Adjust plate (12) to dimension (A) that was recorded in the disassembly procedure.
22. Tighten nut (8) against plate (12). Tighten nut (8) to a torque of 69 ± 5 N·m (51 ± 4 lb ft).
23. Install rubber boot (4) on the pilot valve.
End By:
a. Install the pilot valve. Refer to Disassembly and Assembly, "Pilot Valve (Joystick) - Install".
Sun Sep 15 18:39:25 UTC+0800 2019
7/7
2019/9/15

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01968124
Pilot Valve (Joystick) - Install
SMCS - 5059-012
Installation Procedure
Table 1
Required Tools
A FT-2674 Vacuum Cap 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/5
2019/9/15

1. Remove the cap from the hydraulic tank. Attach Tooling (A) to the hydraulic tank.
Note: Hook up the air to Tooling (A) in order to create a vacuum in the hydraulic system.
This will minimize the leakage from the hose assemblies.
2. Place pilot valve (8), as shown.
3. Connect hose assemblies (10) to pilot valve (8).
4. Remove Tooling (A).
2/5
2019/9/15

5. Place pilot valve (8) in position, as shown. Install bolts (9) to pilot valve (8).
6. Connect harness assemblies (7) to the joystick.
7. Place cover (6) over the joystick, as shown.
8. Connect harness assemblies (5).
9. Install high efficiency filters in place of the pilot filter, the filter for the case drain, and the
return filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
10. Fill the hydraulic oil tank with clean hydraulic oil to the correct level. Refer to Operation
and Maintenance Manual, "Lubricant Viscosities" for the proper oil viscosity and refer to
Operation and Maintenance Manual, "Hydraulic System Oil Level - Check" for the correct
filling procedures.
11. Install the cap to the hydraulic tank.
3/5
2019/9/15

12. Start the engine, and check the operation of the joystick. Also, check for leaks. Stop the
engine.
13. Place cover (6) on the console if the joystick operated properly and no leaks were present.
14. Install armrest (3). Install screws (4).
15. Install screws (2) to the rear of the console.
4/5
2019/9/15

16. Install screws (1). Install the cover over screws (1).
17. Obtain a hydraulic oil sample from the main S·O·S port. Refer to Operation and
Maintenance Manual, "Sampling Interval and Location of Sampling Valve" for the correct
location.
18. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system. Refer to Contamination
Control Guidelines, SEBF8436, "Hydraulic System Flushing Procedure for 320C Hydraulic
Excavators" for further information.
Sun Sep 15 18:40:22 UTC+0800 2019
5/5
2019/9/15

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02344294
Control Manifold (Pilot Oil) - Remove
SMCS - 5059-011-M9
Removal Procedure
Table 1
Required Tools
Start By:
A. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1/4
2019/9/15

NOTICE
performance of inspection, maintenance, testing, adjusting and repair
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Remove bolts (2) in order to remove access cover (1) that is under the main control valve.
2/4
2019/9/15

2. Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach
an air supply hose to Tooling (A) . Apply 276 to 414 kPa (40 to 60 psi) of air. This
procedure will pull vacuum on the hydraulic system.
Note: A small amount of oil will drain from all of the hose assemblies when the hose
assemblies are disconnected from the pilot manifold. Make sure that you contain the
hydraulic oil.
3. Put identification marks on all of the hose assemblies that are connected to the pilot
manifold for installation purposes.
4. Disconnect harness assemblies (3) from control manifold (8) .
5. Disconnect hose assemblies (4) .
Note: Leave the top hose assembly connected. You will be able to remove the top hose
assembly, when the mount bolts are removed.
3/4
2019/9/15

6. Remove cable straps (5) and bolts (6) .
7. Disconnect hose assembly (7) and remove control manifold (8) .
Sun Sep 15 18:41:19 UTC+0800 2019
4/4
2019/9/15

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02349022
Control Manifold (Pilot Oil) - Remove - NFC Limit Valve
SMCS - 5059-011-M9
Removal Procedure
Table 1
Required Tools
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1/5
2019/9/15

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

NOTICE
performance of inspection, maintenance, testing, adjusting, and repair
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
At operating temperature, the hydraulic oil is hot and under pressure.
Hot oils can cause burns.
To prevent possible personal injury, release the pressure in the work
tool hydraulic circuit (boom, stick, bucket, and swing), travel circuits,
and the hydraulic oil tank at the filler cap before any hydraulic lines or
components are disconnected or removed.
Remove the filler cap only when the engine is stopped and the filler cap
is cool enough to touch.
1. Open access door (1) on the right side of the machine.
2/5
2019/9/15

2. Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach
an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This
procedure will pull vacuum on the hydraulic system.
Note: A small amount of oil will drain from all of the hose assemblies when the hose
assemblies are disconnected from the pilot valve. Make sure that you contain the hydraulic
oil.
3. Put identification marks on all of the hose assemblies and on all of the tube assemblies that
are connected to the pilot valve for installation purposes.
4. Disconnect harness assembly (2) and hose assemblies (3).
3/5
2019/9/15

5. Remove bolts (4) in order to remove access cover (5) that is under the main hydraulic pump.
6. Disconnect hose assemblies (6).
7. Remove bolts (7) in order to remove control manifold (8).
Sun Sep 15 18:42:16 UTC+0800 2019
4/5
2019/9/15

Caterpillar Cat 322C Excavator (Prefix DAA) Service Repair Manual (DAA00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 322C Excavator (Prefix DAA) Service Repair Manual (DAA00001 and up).pdf (20)

More from fujsked9dikdkd (20)

Recently uploaded (20)

Caterpillar Cat 322C Excavator (Prefix DAA) Service Repair Manual (DAA00001 and up).pdf