Caterpillar Cat 324D LN Excavator (Prefix EJC) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
324D L and 324D LN Excavator

Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 154-6181 Forcing Screw 1
D 138-7574 Link Bracket 2
E
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F 1U-8846 Gasket Sealant 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3/12
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

3. Remove bolts (1) and the washers that hold the cover in position.
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
4/12
2020/7/21

7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
5/12
2020/7/21

b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
6/12
2020/7/21

13. Remove sun gear (14) from carrier assembly (15).
14. Remove spacer (16).
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
7/12
2020/7/21

16. Use a screwdriver or a chisel in order to separate the two ring gears (17).
Note: The two ring gears are held together with Tooling (F). It may be necessary to heat the
ring gears in order to soften the sealant. Do not heat over 135 °C (275 °F) for more than
thirty minutes.
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
8/12
2020/7/21

b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
9/12
2020/7/21

22. Remove O-ring seal (24) from main housing (18).
23. Remove bolts (25) from gear (26).
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from the main housing (18) once gear (26) is
removed. Make sure that the motor housing is supported.
10/12
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(...
2020/7/21

25. Remove shims (27) from the main housing.
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from the motor housing (28). The combined weight of main housing (18) and the
final drive sprocket is approximately 82 kg (180 lb).
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
11/12
2020/7/21

30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 21 11:51:19 UTC+0800 2020
12/12
2020/7/21

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D LN EXCAVATOR EJC
Configuration: 324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8646-22 Publication Date -01/02/2015 Date Updated -12/09/2018
i02783051
Final Drive - Disassemble
SMCS - 4050-015
S/N - A3R1-1021
S/N - AZP1-UP
S/N - DBH1-UP
S/N - EJC1-643
S/N - GBR1-UP
S/N - GPB1-801
S/N - JJG1-813
S/N - KBE1-UP
S/N - LAB1-415
S/N - LAL1-250
S/N - MCL1-201
S/N - NAC1-250
S/N - PAL1-UP
S/N - PKE1-814
S/N - SCR1-774
S/N - SYM1-617
1/13
2020/7/21

S/N - T2D1-322
S/N - T2S1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 194-3878 Spanner Socket 1
E 138-7574 Link Bracket 2
F
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
G
1U-7600 Slide Hammer Puller Gp 1
8T-0266 Bolt 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
Note: Some of the images that are in this procedure do not show the sprocket assembly that
is attached to the final drive housing. If necessary, the weights that are given include the
weight of the sprocket assembly.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
2/13
2020/7/21

2. Fasten the final drive to Tooling (A), as shown. The weight of the final drive assembly is
3. Remove bolts (1) and the washers that hold the cover in position.
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. Remove the cover. The weight of the cover is approximately 32 kg
(70 lb).
3/13
2020/7/21

5. Remove bolts (3). Remove gear (5). Check plate (6). Replace plate (6) if wear is shown.
Remove plugs (4) from cover (2).
6. Remove O-ring seal (7) from plugs (4).
7. Remove gear (8). Remove spacer (9).
4/13
2020/7/21

8. Remove retaining ring (10) with Tooling (C). Remove washer (11). Remove gear (12).
Remove bearing assembly (13). Remove second washer (11).
9. Repeat Step 8 for the remaining two gear assemblies.
10. Remove retaining ring (14).
11. Remove carrier assembly (15).
5/13
2020/7/21

12. Use a suitable press in order to remove the shafts from carrier assembly (15).
6/13
2020/7/21

14. Remove retaining ring (18).
b. Remove planetary shaft (21).
7/13
2020/7/21

e. Remove bearing (23) from planetary gear (24).
17. Repeat Steps 16.a through 16.e for the other two planetary.
20. Use two people to remove carrier assembly (27). The weight of the carrier assembly is
8/13
2020/7/21

b. Remove planetary shaft (28).
e. Remove two bearings (31) from the planetary gear.
9/13
2020/7/21

22. Repeat Steps 21.a through 21.e for the other two planetary gears.
23. Use two people to remove gear (33). The weight of gear is approximately 41 kg (90 lb).
24. Remove O-ring seal (34).
25. Remove bolts (35A) and plates (35B).
10/13
2020/7/21

26. Use Tooling (G) to remove dowel (37) from stopper plate (35).
27. Secure Tooling (D) to stopper plate (35). Use Tooling (D) to remove stopper plate (35).
28. Use Tooling (E) and a suitable lifting device to remove housing (36). The weight of housing
(36) is approximately 100 kg (220 lb).
11/13
2020/7/21

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

29. Remove Duo-Cone seal (39A) from housing (38).
30. Remove Duo-Cone seal (39B) from housing (36).
31. Use Tooling (F) in order to remove bearings (40) and (41) from housing (36).
32. If necessary, remove the final drive sprocket from the sprocket housing. Refer to
Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
12/13
2020/7/21

Caterpillar Cat 324D LN Excavator (Prefix EJC) Service Repair Manual Instant Download.pdf

More Related Content

Similar to Caterpillar Cat 324D LN Excavator (Prefix EJC) Service Repair Manual Instant Download.pdf (15)

More from rishang96299 (20)

Recently uploaded (20)

Caterpillar Cat 324D LN Excavator (Prefix EJC) Service Repair Manual Instant Download.pdf