Abstract image of a woman sitting on books and studying on a laptop

Caterpillar Cat 325 EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM00001 and up).pdf

J
jfkskmmdmdm

This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Special markings and care are required to keep components in their original positions for reassembly.

Automotive
1 of 28
Download to read offline
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Service Repair Manual Models 325-A FM L 325 325L EXCAVATOR
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 325-A FM L EXCAVATOR 7LM Configuration: 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGINE Disassembly and Assembly 325, 325B and 325L Excavators Media Number -RENR1178-03 Publication Date -01/09/2000 Date Updated -09/10/2001 i01765040 Travel Motor - Disassemble SMCS - 4351-015 Disassembly Procedure For The Travel Motor On CIPI Undercarriage Arrangements Which Are Based On 325 Track Type Excavators Start By: A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" in this manual. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the travel motor is approximately 71 kg (157 lb). 1/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
2. Put an alignment mark across the head and the body of the travel motor for assembly purposes. The head must be reinstalled in the head's original position on the travel motor body. Illustration 1 g00510326 3. Remove nine socket head bolts (1) and head (2) from the travel motor body. Note: During the removal of head (2) from the travel motor body, be careful not to damage the mating surfaces of the components. Illustration 2 g00510341 2/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 3 g00510349 4. Turn over head (2). Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head. Remove the two check valve assemblies from the head. Note: There is a retainer that is located under spring (9). This retainer is a press fit in head (2). Do not remove the retainer. 5. Insert a dowel rod with a small diameter into hole "X". Tap the dowel rod with a plastic hammer in order to remove spring (9), poppet (8) and seat (7) from the head. Illustration 4 g00510351 6. Remove three fittings (10) and four plugs (11) from the head. Remove the O-ring seal from each fitting. 3/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 5 g00510352 7. Remove three O-ring seals (12) and washer set (13) from the body of the travel motor. 8. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply approximately 525 kPa (75 psi) of shop air pressure to brake release port "Y". Make sure that the shop air pressure is free of water. Brake piston (14) will move up the piston guide, and out of the piston guide. Remove brake piston (14) from the travel motor body. Illustration 6 g00510353 9. Remove O-ring seals (15) and (17), and backup rings (16) and (18) from the brake piston. 4/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 7 g00510356 10. Remove piston guide (19), three friction plates and three steel plates (20) from the travel motor body. Illustration 8 g00510359 11. Remove O-ring seal (21) and backup ring (22) from the piston guide. Illustration 9 g00510365 5/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Note: Do not allow the components of barrel assembly (23) to come apart during the removal from the travel motor. All of the components in the barrel assembly must be reinstalled in the component's original location. 12. Use two large screwdrivers and slowly remove barrel assembly (23) from the travel motor body, as shown. Do not allow the components to fall apart. Illustration 10 g00510502 13. Shoe retainer (24) and piston shoe assemblies (25) are nonserviceable separately. Prior to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put identification marks on piston shoe assemblies (25) for assembly purposes. Identification marks are used to identify the piston shoe assembly's location in shoe retainer (24) and barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's original bores in the shoe retainer and the barrel. 14. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the piston shoe assemblies from the shoe retainer. Illustration 11 g00510504 15. Remove guide (27), spacer (28) and nine springs (29) from the barrel. 6/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 12 g00510547 16. Remove cam plate (30) from the travel motor body. Illustration 13 g00919084 17. Put identification marks on two balls (31) and two keys (32) in the travel motor body for assembly purposes. Remove two balls (31) and two keys (32) from the travel motor body. 7/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 14 g00510551 18. Remove O-ring seal (33) from the travel motor body. 19. Use a soft faced hammer to remove shaft assembly (34) from the travel motor body. Remove the shaft assembly in the direction that is indicated by the arrow. Refer to Illustration 33. Illustration 15 g00510595 20. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing (36) with a press. Illustration 16 g00510598 21. Remove inner race (37) from shaft (34) . 8/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 17 g00510599 22. Remove lip type seal (38) from the travel motor body. Illustration 18 g00510605 Illustration 19 g00918957 23. Remove two cam plate tension adjusters from the travel motor body. Loosen two nuts (39). Remove two adjusters (40), two springs (43), and two pistons (44) from the travel motor body. 9/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Remove O-ring seal (42) and backup ring (41) from each adjuster (40) . Disassembly Procedure For The Travel Motor On CIPI Undercarriage Arrangements Which Are Based On 325B Track Type Excavators Start By: A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" in this manual. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the travel motor is approximately 50 kg (110 lb). 2. Put an alignment mark across the head and the body of the travel motor for assembly purposes. The head must be reinstalled in the head's original position on the travel motor body. 10/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 20 g00510326 3. Remove ten socket head bolts (1) and head (2) from the travel motor body. Note: During the removal of head (2) from the travel motor body, be careful not to damage the mating surfaces of the components. Illustration 21 g00510341 Illustration 22 g00510349 4. Turn over head (2). Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head. Remove the two check valve assemblies from the head. Note: There is a retainer that is located under spring (9). This retainer is a press fit in head (2). Do not remove the retainer. 5. Insert a dowel rod with a small diameter into hole "X". Tap the dowel rod with a plastic hammer in order to remove spring (9), poppet (8) and seat (7) from the head. 11/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 23 g00510351 6. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each fitting. Illustration 24 g00510352 7. Remove three O-ring seals (12) and washer set (13) from the travel motor body. 8. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply approximately 525 kPa (75 psi) of shop air pressure to brake release port "Y". Make sure that the shop air pressure is free of water. Brake piston (14) will move up the piston guide, and out of the piston guide. Remove brake piston (14) from the travel motor body. 12/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 25 g00510353 9. Remove O-ring seals (15) and (17) from the brake piston. Remove backup rings (16) and (18) from the brake piston. Illustration 26 g00510356 10. Remove piston guide (19), five friction plates (20) and the four steel plates from the travel motor body. Illustration 27 g00510359 13/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Remove O-ring seal (21) and backup ring (22) from the piston guide. Illustration 28 g00510365 Note: Do not allow the components of barrel assembly (23) to come apart during the removal from the travel motor. All of the components in the barrel assembly must be reinstalled in the component's original location. 12. Use two large screwdrivers and slowly remove barrel assembly (23) from the travel motor body, as shown. Do not allow the components to fall apart. Illustration 29 g00510502 13. Shoe retainer (24) and piston shoe assemblies (25) are nonserviceable separately. Prior to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put identification marks on piston shoe assemblies (25) for assembly purposes. Identification marks are used to identify the piston shoe assembly's location in shoe retainer (24) and barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's original bores in the shoe retainer and the barrel. 14. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the piston shoe assemblies from the shoe retainer. 14/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 30 g00510504 15. Remove guide (27), spacer (28) and nine springs (29) from the barrel. Illustration 31 g00510547 16. Remove cam plate (30) from the body of the travel motor. 15/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 32 g00510550 17. Remove two keys (31) and the two locating pins (not shown) from the travel motor body. Illustration 33 g00510551 18. Remove O-ring seal (33) from the travel motor body. 19. Use a soft faced hammer to remove shaft assembly (34) from the travel motor body. Remove the shaft assembly in the direction that is indicated by the arrow. Refer to Illustration 33. Illustration 34 g00510595 20. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing (36) with a press. 16/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 35 g00510598 21. Remove inner race (37) from shaft (34) . Illustration 36 g00510599 22. Remove lip type seal (38) from the travel motor body. Illustration 37 g00510605 17/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Remove two cam plate tension adjusters from the travel motor body. Loosen two nuts (39). Remove two adjusters (40), two springs (43), and two pistons (44) from the travel motor body. 24. Remove O-ring seal (42) and backup ring (41) from each adjuster (40) . Disassembly Procedure For The Travel Motor On CIPI Undercarriage Arrangements Which Are Based On 325C Track Type Excavators Start By: A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" in this manual. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Thoroughly clean the outside of the travel motor prior to disassembly. 2. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the travel motor is 60 kg (132 lb). 3. Put an alignment mark across the head and the body of the travel motor for assembly purposes. The head must be reinstalled in the head's original position on the body of the travel motor. 18/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 38 g00510326 Note: During the removal of head (2) from the travel motor, be careful not to damage the mating surfaces of the components. 4. Remove bolts (1) . 5. Remove head (2) from the body of the travel motor. Illustration 39 g00510341 Illustration 40 g00510349 19/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Turn over head (2) . 7. Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head. 8. Remove the check valve assemblies from the head. Note: There is a retainer under spring (9). This retainer is a press fit in head (2). Do not remove the retainer. 9. Insert a dowel rod with a small diameter into Hole (X). Tap the dowel rod with a plastic hammer in order to remove spring (9), poppet (8), and seat (7) from the head. Illustration 41 g00510351 10. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each fitting. Illustration 42 g00878239 11. Remove O-ring seals (13) and washer set (12) from the body of the travel motor. 12. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure 20/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
that the shop air pressure is free of water. Brake piston (14) will move up the piston guide, and out of the piston guide. Remove brake piston (14) from the body of the travel motor. Illustration 43 g00878248 13. Remove O-ring seal (16) from the brake piston. Remove backup ring (15) from the brake piston. 14. Remove O-ring seal (17) from the brake piston. Remove backup ring (18) from the brake piston. Illustration 44 g00510356 15. Remove piston guide (19), five friction plates (20) and the four steel plates from the body of the travel motor. 21/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 45 g00510359 16. Remove O-ring seal (21) from the piston guide. Remove backup ring (22) from the piston guide. Illustration 46 g00510365 Note: Do not allow the components of barrel assembly (23) to come apart during the removal from the travel motor. All of the components in the barrel assembly must be reinstalled in the component's original location. 17. Use two large screwdrivers, as shown. Slowly remove barrel assembly (23) from the body of the travel motor. Do not allow the components to fall apart. 22/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 47 g00878253 Note: Shoe retainer (24) and piston shoe assemblies (25) are nonserviceable separately. Prior to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put identification marks on piston shoe assemblies (25) for assembly purposes. Identification marks are used to identify the piston shoe assembly's location in shoe retainer (24) and barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's original bores in the shoe retainer and the barrel. 18. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the piston shoe assemblies from the shoe retainer. Illustration 48 g00510504 19. Remove guide (27), spacer (28), and springs (29) from the barrel. 23/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
Illustration 49 g00510547 20. Remove cam plate (30) from the body of the travel motor. Illustration 50 g00510550 21. Remove two keys (31) and the two locating pins (not shown) from the body of the travel motor. Illustration 51 g00510551 24/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Remove O-ring seal (33) from the body of the travel motor. 23. Use a soft faced hammer to remove shaft assembly (34) from the body of the travel motor. Remove the shaft assembly in the direction that is indicated by the arrow. Refer to Illustration 51. Illustration 52 g00510595 24. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing (36) with a press. Illustration 53 g00510598 25. Remove inner race (37) from shaft (34) . 25/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
Illustration 54 g00510599 26. Remove lip seal (38) from the body of the travel motor. Illustration 55 g00510605 27. Remove two stoppers (39) and the two pistons from the body of the travel motor. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Thu Aug 6 11:21:23 UTC+0800 2020 26/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

More Related Content

PDF
Caterpillar Cat 325-A, 325, 325L EXCAVATOR (Prefix 7TG) Service Repair Manual...
yan77xunhao
 
PDF
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...
ifoseidkkd
 
PDF
Caterpillar Cat 325 EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 an...
f8usiejdkmdd
 
PDF
Caterpillar Cat 325L EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 a...
f8usiejdkmdd
 
PDF
Caterpillar Cat 325-A EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 ...
f8usiejdkmdd
 
PDF
Caterpillar Cat 325-A EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 ...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325 EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 an...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325L EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 a...
dujdkksdmm
 
Caterpillar Cat 325-A, 325, 325L EXCAVATOR (Prefix 7TG) Service Repair Manual...
yan77xunhao
 
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...
ifoseidkkd
 
Caterpillar Cat 325 EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 an...
f8usiejdkmdd
 
Caterpillar Cat 325L EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 a...
f8usiejdkmdd
 
Caterpillar Cat 325-A EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 ...
f8usiejdkmdd
 
Caterpillar Cat 325-A EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 ...
jfkskmmdmdm
 
Caterpillar Cat 325 EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 an...
jfkskmmdmdm
 
Caterpillar Cat 325L EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 a...
dujdkksdmm
 

Similar to Caterpillar Cat 325 EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM00001 and up).pdf (14)

PDF
Caterpillar Cat 325-A EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 ...
jfkskmdmmdd
 
PDF
Caterpillar Cat 325 EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 an...
jfkskmdmmdd
 
PDF
Caterpillar cat 325 l excavator (prefix 7tg) service repair manual (7tg00001 ...
ifoseidkkd
 
PDF
Caterpillar cat 325 excavator (prefix 7 tg) service repair manual (7tg00001 a...
ifoseidkkd
 
PDF
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...
fujsekksmem
 
PDF
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...
fjskkmemem
 
PDF
Caterpillar cat 325 l excavator (prefix 7tg) service repair manual (7tg00001 ...
fjskkmemem
 
PDF
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...
JayHaines2
 
PDF
Caterpillar cat 325 excavator (prefix 7 tg) service repair manual (7tg00001 a...
JayHaines2
 
PDF
Caterpillar cat 325 l excavator (prefix 7tg) service repair manual (7tg00001 ...
JayHaines2
 
PDF
Caterpillar cat 325 excavator (prefix 7 tg) service repair manual (7tg00001 a...
fujsekksmem
 
PDF
Caterpillar cat 325 excavator (prefix 7 tg) service repair manual (7tg00001 a...
fjskkmemem
 
PDF
Caterpillar cat 325 b track type excavator (prefix 8pr) service repair manual...
fjsjjekdkme
 
PDF
Caterpillar cat 325 b l track type excavator (prefix 8pr) service repair manu...
fjsjjekdkme
 
Caterpillar Cat 325-A EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 ...
jfkskmdmmdd
 
Caterpillar Cat 325 EXCAVATOR (Prefix 7TG) Service Repair Manual (7TG00001 an...
jfkskmdmmdd
 
Caterpillar cat 325 l excavator (prefix 7tg) service repair manual (7tg00001 ...
ifoseidkkd
 
Caterpillar cat 325 excavator (prefix 7 tg) service repair manual (7tg00001 a...
ifoseidkkd
 
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...
fujsekksmem
 
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...
fjskkmemem
 
Caterpillar cat 325 l excavator (prefix 7tg) service repair manual (7tg00001 ...
fjskkmemem
 
Caterpillar cat 325 a excavator (prefix 7 tg) service repair manual (7tg00001...
JayHaines2
 
Caterpillar cat 325 excavator (prefix 7 tg) service repair manual (7tg00001 a...
JayHaines2
 
Caterpillar cat 325 l excavator (prefix 7tg) service repair manual (7tg00001 ...
JayHaines2
 
Caterpillar cat 325 excavator (prefix 7 tg) service repair manual (7tg00001 a...
fujsekksmem
 
Caterpillar cat 325 excavator (prefix 7 tg) service repair manual (7tg00001 a...
fjskkmemem
 
Caterpillar cat 325 b track type excavator (prefix 8pr) service repair manual...
fjsjjekdkme
 
Caterpillar cat 325 b l track type excavator (prefix 8pr) service repair manu...
fjsjjekdkme
 

More from jfkskmmdmdm (20)

PDF
DAEWOO DOOSAN MEGA 160TC TIER-II WHEEL LOADER Parts Catalogue Manual.pdf
jfkskmmdmdm
 
PDF
Caterpillar Cat 325B Excavator (Prefix 6DN) Service Repair Manual (6DN00001 a...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325D Excavator (Prefix PKE) Service Repair Manual (PKE00001 a...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325-A EXCAVATOR (Prefix 8YK) Service Repair Manual (8YK00001 ...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325B L Excavator (Prefix 1GS) Service Repair Manual (1GS00001...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325B L Excavator (Prefix 6DN) Service Repair Manual (6DN00001...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325B Excavator (Prefix 8FN) Service Repair Manual (8FN00001 a...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325-A TRACK TYPE EXCAVATOR (Prefix 8NL) Service Repair Manual...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325-A TRACK TYPE EXCAVATOR (Prefix 8JG) Service Repair Manual...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325-A FM L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM0...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325-A EXCAVATOR (Prefix 9SG) Service Repair Manual (9SG00001 ...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325-A FM L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM0...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325-A EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001 ...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325 L EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001 ...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325-A EXCAVATOR (Prefix 6RM) Service Repair Manual (6RM00001 ...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325 LN EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 8NL) Service Repair Manual (...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 8JG) Service Repair Manual (...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325 EXCAVATOR (Prefix 8YK) Service Repair Manual (8YK00001 an...
jfkskmmdmdm
 
PDF
Caterpillar Cat 325 EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001 an...
jfkskmmdmdm
 
DAEWOO DOOSAN MEGA 160TC TIER-II WHEEL LOADER Parts Catalogue Manual.pdf
jfkskmmdmdm
 
Caterpillar Cat 325B Excavator (Prefix 6DN) Service Repair Manual (6DN00001 a...
jfkskmmdmdm
 
Caterpillar Cat 325D Excavator (Prefix PKE) Service Repair Manual (PKE00001 a...
jfkskmmdmdm
 
Caterpillar Cat 325-A EXCAVATOR (Prefix 8YK) Service Repair Manual (8YK00001 ...
jfkskmmdmdm
 
Caterpillar Cat 325B L Excavator (Prefix 1GS) Service Repair Manual (1GS00001...
jfkskmmdmdm
 
Caterpillar Cat 325B L Excavator (Prefix 6DN) Service Repair Manual (6DN00001...
jfkskmmdmdm
 
Caterpillar Cat 325B Excavator (Prefix 8FN) Service Repair Manual (8FN00001 a...
jfkskmmdmdm
 
Caterpillar Cat 325-A TRACK TYPE EXCAVATOR (Prefix 8NL) Service Repair Manual...
jfkskmmdmdm
 
Caterpillar Cat 325-A TRACK TYPE EXCAVATOR (Prefix 8JG) Service Repair Manual...
jfkskmmdmdm
 
Caterpillar Cat 325-A FM L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM0...
jfkskmmdmdm
 
Caterpillar Cat 325-A EXCAVATOR (Prefix 9SG) Service Repair Manual (9SG00001 ...
jfkskmmdmdm
 
Caterpillar Cat 325-A FM L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM0...
jfkskmmdmdm
 
Caterpillar Cat 325-A EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001 ...
jfkskmmdmdm
 
Caterpillar Cat 325 L EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001 ...
jfkskmmdmdm
 
Caterpillar Cat 325-A EXCAVATOR (Prefix 6RM) Service Repair Manual (6RM00001 ...
jfkskmmdmdm
 
Caterpillar Cat 325 LN EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001...
jfkskmmdmdm
 
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 8NL) Service Repair Manual (...
jfkskmmdmdm
 
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 8JG) Service Repair Manual (...
jfkskmmdmdm
 
Caterpillar Cat 325 EXCAVATOR (Prefix 8YK) Service Repair Manual (8YK00001 an...
jfkskmmdmdm
 
Caterpillar Cat 325 EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001 an...
jfkskmmdmdm
 

Recently uploaded (20)

PDF
Volvo Dump Truck A40E Service Repair Manual.pdf
Nombre Apellidos
 
PPT
157_37315_EA221_2013_1__2_1_Chapter 1, introduction to OR.ppt
SIRINET2
 
PDF
BOBCAT 442 muffler SN 522311001 & Above.pdf
Service Repair Manual
 
PDF
D6E Engine Volvo EC160C NL Excavator Service Repair Manual.pdf
Service Repair Manual
 
PDF
Smart_Doors_Trunk_Control_Presentation.pdf
XEEDO
 
PDF
Where to Buy Verified LinkedIn Accounts Securely in 2025.pdf
trampdonal260
 
PPT
industrialsafetyhazards-180118095222.ppt
gmoudgil1
 
DOCX
MLS 221 Medical Parasitology (LABORATORY).docx
aldrinpineda1996
 
PDF
Bobcat t40140, t40180 telescopic handler service repair manual (sn b33 j11001...
Service Repair Manual
 
PPTX
Pre-ph.d. presentation on numeric study of some double diffusive convection r...
chandansinghmaharajp
 
PDF
CASE CX55B Mini Excavator Service Repair Manual Instant Download.pdf
zhongxiaqielan90
 
PDF
John Deere 5055e Fuel System Repair Manual - Tm900319.pdf
Service Repair Manual
 
DOC
Bài tập bổ trợ I-learn Smart World 9 HK1 Unit 4 (HS) (1).doc
XunHuyn12
 
PDF
BCM-hardware-schematics in automotive electronics.pdf
XEEDO
 
PDF
D85PX-15E0 Komatsu d85 px 15e0 dozer bulldozer Technical manual.pdf
hejifob514
 
PDF
CASE CX45B Series 2 Mini Excavator Service Repair Manual Instant Download.pdf
zhongxiaqielan90
 
PDF
Lightweight-and-quantum-resistant-authentication-for-the-Internet-of-Drones-I...
peran1805
 
PPTX
DNA Packaging in Eukaryot ic Cells.pptx
AbhijithA57
 
PPTX
Air craft and Rescue related ppt which detailed explain about
akhilsbr
 
PDF
Deep Learning and AI Tools for Monitoring and Detecting Diseases in Freshwate...
PriyankaKilaniya
 
Volvo Dump Truck A40E Service Repair Manual.pdf
Nombre Apellidos
 
157_37315_EA221_2013_1__2_1_Chapter 1, introduction to OR.ppt
SIRINET2
 
BOBCAT 442 muffler SN 522311001 & Above.pdf
Service Repair Manual
 
D6E Engine Volvo EC160C NL Excavator Service Repair Manual.pdf
Service Repair Manual
 
Smart_Doors_Trunk_Control_Presentation.pdf
XEEDO
 
Where to Buy Verified LinkedIn Accounts Securely in 2025.pdf
trampdonal260
 
industrialsafetyhazards-180118095222.ppt
gmoudgil1
 
MLS 221 Medical Parasitology (LABORATORY).docx
aldrinpineda1996
 
Bobcat t40140, t40180 telescopic handler service repair manual (sn b33 j11001...
Service Repair Manual
 
Pre-ph.d. presentation on numeric study of some double diffusive convection r...
chandansinghmaharajp
 
CASE CX55B Mini Excavator Service Repair Manual Instant Download.pdf
zhongxiaqielan90
 
John Deere 5055e Fuel System Repair Manual - Tm900319.pdf
Service Repair Manual
 
Bài tập bổ trợ I-learn Smart World 9 HK1 Unit 4 (HS) (1).doc
XunHuyn12
 
BCM-hardware-schematics in automotive electronics.pdf
XEEDO
 
D85PX-15E0 Komatsu d85 px 15e0 dozer bulldozer Technical manual.pdf
hejifob514
 
CASE CX45B Series 2 Mini Excavator Service Repair Manual Instant Download.pdf
zhongxiaqielan90
 
Lightweight-and-quantum-resistant-authentication-for-the-Internet-of-Drones-I...
peran1805
 
DNA Packaging in Eukaryot ic Cells.pptx
AbhijithA57
 
Air craft and Rescue related ppt which detailed explain about
akhilsbr
 
Deep Learning and AI Tools for Monitoring and Detecting Diseases in Freshwate...
PriyankaKilaniya
 

Caterpillar Cat 325 EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM00001 and up).pdf

  • 1. Service Repair Manual Models 325-A FM L 325 325L EXCAVATOR
  • 2. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 325-A FM L EXCAVATOR 7LM Configuration: 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGINE Disassembly and Assembly 325, 325B and 325L Excavators Media Number -RENR1178-03 Publication Date -01/09/2000 Date Updated -09/10/2001 i01765040 Travel Motor - Disassemble SMCS - 4351-015 Disassembly Procedure For The Travel Motor On CIPI Undercarriage Arrangements Which Are Based On 325 Track Type Excavators Start By: A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" in this manual. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the travel motor is approximately 71 kg (157 lb). 1/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 3. 2. Put an alignment mark across the head and the body of the travel motor for assembly purposes. The head must be reinstalled in the head's original position on the travel motor body. Illustration 1 g00510326 3. Remove nine socket head bolts (1) and head (2) from the travel motor body. Note: During the removal of head (2) from the travel motor body, be careful not to damage the mating surfaces of the components. Illustration 2 g00510341 2/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 4. Illustration 3 g00510349 4. Turn over head (2). Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head. Remove the two check valve assemblies from the head. Note: There is a retainer that is located under spring (9). This retainer is a press fit in head (2). Do not remove the retainer. 5. Insert a dowel rod with a small diameter into hole "X". Tap the dowel rod with a plastic hammer in order to remove spring (9), poppet (8) and seat (7) from the head. Illustration 4 g00510351 6. Remove three fittings (10) and four plugs (11) from the head. Remove the O-ring seal from each fitting. 3/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 5. Illustration 5 g00510352 7. Remove three O-ring seals (12) and washer set (13) from the body of the travel motor. 8. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply approximately 525 kPa (75 psi) of shop air pressure to brake release port "Y". Make sure that the shop air pressure is free of water. Brake piston (14) will move up the piston guide, and out of the piston guide. Remove brake piston (14) from the travel motor body. Illustration 6 g00510353 9. Remove O-ring seals (15) and (17), and backup rings (16) and (18) from the brake piston. 4/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 6. Illustration 7 g00510356 10. Remove piston guide (19), three friction plates and three steel plates (20) from the travel motor body. Illustration 8 g00510359 11. Remove O-ring seal (21) and backup ring (22) from the piston guide. Illustration 9 g00510365 5/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 7. Note: Do not allow the components of barrel assembly (23) to come apart during the removal from the travel motor. All of the components in the barrel assembly must be reinstalled in the component's original location. 12. Use two large screwdrivers and slowly remove barrel assembly (23) from the travel motor body, as shown. Do not allow the components to fall apart. Illustration 10 g00510502 13. Shoe retainer (24) and piston shoe assemblies (25) are nonserviceable separately. Prior to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put identification marks on piston shoe assemblies (25) for assembly purposes. Identification marks are used to identify the piston shoe assembly's location in shoe retainer (24) and barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's original bores in the shoe retainer and the barrel. 14. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the piston shoe assemblies from the shoe retainer. Illustration 11 g00510504 15. Remove guide (27), spacer (28) and nine springs (29) from the barrel. 6/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 8. Illustration 12 g00510547 16. Remove cam plate (30) from the travel motor body. Illustration 13 g00919084 17. Put identification marks on two balls (31) and two keys (32) in the travel motor body for assembly purposes. Remove two balls (31) and two keys (32) from the travel motor body. 7/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 9. Illustration 14 g00510551 18. Remove O-ring seal (33) from the travel motor body. 19. Use a soft faced hammer to remove shaft assembly (34) from the travel motor body. Remove the shaft assembly in the direction that is indicated by the arrow. Refer to Illustration 33. Illustration 15 g00510595 20. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing (36) with a press. Illustration 16 g00510598 21. Remove inner race (37) from shaft (34) . 8/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 10. Illustration 17 g00510599 22. Remove lip type seal (38) from the travel motor body. Illustration 18 g00510605 Illustration 19 g00918957 23. Remove two cam plate tension adjusters from the travel motor body. Loosen two nuts (39). Remove two adjusters (40), two springs (43), and two pistons (44) from the travel motor body. 9/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENGIN... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 11. 24. Remove O-ring seal (42) and backup ring (41) from each adjuster (40) . Disassembly Procedure For The Travel Motor On CIPI Undercarriage Arrangements Which Are Based On 325B Track Type Excavators Start By: A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" in this manual. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Thoroughly clean the outside of the travel motor prior to disassembly. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the travel motor is approximately 50 kg (110 lb). 2. Put an alignment mark across the head and the body of the travel motor for assembly purposes. The head must be reinstalled in the head's original position on the travel motor body. 10/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 12. Illustration 20 g00510326 3. Remove ten socket head bolts (1) and head (2) from the travel motor body. Note: During the removal of head (2) from the travel motor body, be careful not to damage the mating surfaces of the components. Illustration 21 g00510341 Illustration 22 g00510349 4. Turn over head (2). Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head. Remove the two check valve assemblies from the head. Note: There is a retainer that is located under spring (9). This retainer is a press fit in head (2). Do not remove the retainer. 5. Insert a dowel rod with a small diameter into hole "X". Tap the dowel rod with a plastic hammer in order to remove spring (9), poppet (8) and seat (7) from the head. 11/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 13. Illustration 23 g00510351 6. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each fitting. Illustration 24 g00510352 7. Remove three O-ring seals (12) and washer set (13) from the travel motor body. 8. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply approximately 525 kPa (75 psi) of shop air pressure to brake release port "Y". Make sure that the shop air pressure is free of water. Brake piston (14) will move up the piston guide, and out of the piston guide. Remove brake piston (14) from the travel motor body. 12/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 14. Illustration 25 g00510353 9. Remove O-ring seals (15) and (17) from the brake piston. Remove backup rings (16) and (18) from the brake piston. Illustration 26 g00510356 10. Remove piston guide (19), five friction plates (20) and the four steel plates from the travel motor body. Illustration 27 g00510359 13/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 15. 11. Remove O-ring seal (21) and backup ring (22) from the piston guide. Illustration 28 g00510365 Note: Do not allow the components of barrel assembly (23) to come apart during the removal from the travel motor. All of the components in the barrel assembly must be reinstalled in the component's original location. 12. Use two large screwdrivers and slowly remove barrel assembly (23) from the travel motor body, as shown. Do not allow the components to fall apart. Illustration 29 g00510502 13. Shoe retainer (24) and piston shoe assemblies (25) are nonserviceable separately. Prior to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put identification marks on piston shoe assemblies (25) for assembly purposes. Identification marks are used to identify the piston shoe assembly's location in shoe retainer (24) and barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's original bores in the shoe retainer and the barrel. 14. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the piston shoe assemblies from the shoe retainer. 14/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 16. Illustration 30 g00510504 15. Remove guide (27), spacer (28) and nine springs (29) from the barrel. Illustration 31 g00510547 16. Remove cam plate (30) from the body of the travel motor. 15/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 17. Illustration 32 g00510550 17. Remove two keys (31) and the two locating pins (not shown) from the travel motor body. Illustration 33 g00510551 18. Remove O-ring seal (33) from the travel motor body. 19. Use a soft faced hammer to remove shaft assembly (34) from the travel motor body. Remove the shaft assembly in the direction that is indicated by the arrow. Refer to Illustration 33. Illustration 34 g00510595 20. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing (36) with a press. 16/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 18. Illustration 35 g00510598 21. Remove inner race (37) from shaft (34) . Illustration 36 g00510599 22. Remove lip type seal (38) from the travel motor body. Illustration 37 g00510605 17/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 19. 23. Remove two cam plate tension adjusters from the travel motor body. Loosen two nuts (39). Remove two adjusters (40), two springs (43), and two pistons (44) from the travel motor body. 24. Remove O-ring seal (42) and backup ring (41) from each adjuster (40) . Disassembly Procedure For The Travel Motor On CIPI Undercarriage Arrangements Which Are Based On 325C Track Type Excavators Start By: A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove" in this manual. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. 1. Thoroughly clean the outside of the travel motor prior to disassembly. 2. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the travel motor is 60 kg (132 lb). 3. Put an alignment mark across the head and the body of the travel motor for assembly purposes. The head must be reinstalled in the head's original position on the body of the travel motor. 18/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 20. Illustration 38 g00510326 Note: During the removal of head (2) from the travel motor, be careful not to damage the mating surfaces of the components. 4. Remove bolts (1) . 5. Remove head (2) from the body of the travel motor. Illustration 39 g00510341 Illustration 40 g00510349 19/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 21. 6. Turn over head (2) . 7. Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head. 8. Remove the check valve assemblies from the head. Note: There is a retainer under spring (9). This retainer is a press fit in head (2). Do not remove the retainer. 9. Insert a dowel rod with a small diameter into Hole (X). Tap the dowel rod with a plastic hammer in order to remove spring (9), poppet (8), and seat (7) from the head. Illustration 41 g00510351 10. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each fitting. Illustration 42 g00878239 11. Remove O-ring seals (13) and washer set (12) from the body of the travel motor. 12. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure 20/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 22. that the shop air pressure is free of water. Brake piston (14) will move up the piston guide, and out of the piston guide. Remove brake piston (14) from the body of the travel motor. Illustration 43 g00878248 13. Remove O-ring seal (16) from the brake piston. Remove backup ring (15) from the brake piston. 14. Remove O-ring seal (17) from the brake piston. Remove backup ring (18) from the brake piston. Illustration 44 g00510356 15. Remove piston guide (19), five friction plates (20) and the four steel plates from the body of the travel motor. 21/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 23. Illustration 45 g00510359 16. Remove O-ring seal (21) from the piston guide. Remove backup ring (22) from the piston guide. Illustration 46 g00510365 Note: Do not allow the components of barrel assembly (23) to come apart during the removal from the travel motor. All of the components in the barrel assembly must be reinstalled in the component's original location. 17. Use two large screwdrivers, as shown. Slowly remove barrel assembly (23) from the body of the travel motor. Do not allow the components to fall apart. 22/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 24. Illustration 47 g00878253 Note: Shoe retainer (24) and piston shoe assemblies (25) are nonserviceable separately. Prior to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put identification marks on piston shoe assemblies (25) for assembly purposes. Identification marks are used to identify the piston shoe assembly's location in shoe retainer (24) and barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's original bores in the shoe retainer and the barrel. 18. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the piston shoe assemblies from the shoe retainer. Illustration 48 g00510504 19. Remove guide (27), spacer (28), and springs (29) from the barrel. 23/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 25. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
  • 26. Illustration 49 g00510547 20. Remove cam plate (30) from the body of the travel motor. Illustration 50 g00510550 21. Remove two keys (31) and the two locating pins (not shown) from the body of the travel motor. Illustration 51 g00510551 24/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 27. 22. Remove O-ring seal (33) from the body of the travel motor. 23. Use a soft faced hammer to remove shaft assembly (34) from the body of the travel motor. Remove the shaft assembly in the direction that is indicated by the arrow. Refer to Illustration 51. Illustration 52 g00510595 24. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing (36) with a press. Illustration 53 g00510598 25. Remove inner race (37) from shaft (34) . 25/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
  • 28. Illustration 54 g00510599 26. Remove lip seal (38) from the body of the travel motor. Illustration 55 g00510605 27. Remove two stoppers (39) and the two pistons from the body of the travel motor. Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Thu Aug 6 11:21:23 UTC+0800 2020 26/26 325, 325L EXCAVATOR 7LM00001-UP (MACHINE) POWERED BY 3116 ENG... 2020/8/6 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...