Caterpillar Cat 325C EXCAVATOR (Prefix BKT) Service Repair Manual (BKT00001 and up).pdf

Service Repair Manual
Models
325C EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR BKT
Configuration: ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01980480
Flywheel - Remove and Install
SMCS - 1156-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B FT2712 Guide Stud 2
1/3
ISJ HEX COMMONALITY CHART BKT00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01026562
1. Install Tooling (A) on the flywheel. Fasten a suitable lifting device to the flywheel. The
weight of flywheel (1) is approximately 23 kg (50 lb).
2. Remove two bolts and install Tooling (B). Remove the remaining bolts.
3. Remove flywheel (1).
4. Place the flywheel on a wood block. Use a hammer and a punch in order to remove the
flywheel ring gear.
Installation Procedure
Table 2
Required Tools
B FT2712 Guide Stud 2
C 9S-3263 Thread Lock Compound 1
2/3
2020/5/16

1. Raise the temperature of the flywheel ring gear. Do not use a torch to heat the flywheel ring
gear. Position the flywheel ring gear on the flywheel with the part number toward the
crankshaft.
2. Use a suitable lifting device to position flywheel (1) on Tooling (B). The weight of flywheel
(1) is approximately 23 kg (50 lb).
3. Apply Tooling (C) to the threads of the bolts. Install the bolts. Remove Tooling (B) and
install the remaining bolts.
4. Tighten the bolts evenly to a torque of 120 ± 20 N·m (90 ± 15 lb ft).
5. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for the
correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 16 18:47:07 UTC+0800 2020
3/3
2020/5/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01980554
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
A 1U-8145 Drill Bit 1
B 1U-7600 Slide Hammer Puller Gp 1
C 4C-4869 Distorter Ring 1
D 5P-7312 Seal Distorter 1
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (A) to drill three evenly spaced holes in the crankshaft rear seal.
1/2
2020/5/16

2. Carefully remove crankshaft rear seal (1) by alternating the position of Tooling (B) from
hole to hole. This will allow crankshaft rear seal (1) to be removed evenly without damage
to the rear flange surface of the crankshaft.
Note: New engines from the factory do not have a wear sleeve. Engines with seals that have
been replaced will be equipped with a wear sleeve. If the crankshaft of the engine is
equipped with a wear sleeve, refer to Disassembly and Assembly, "Crankshaft Wear Sleeve
(Rear) - Remove" in order to remove the wear sleeve.
3. Use Tooling (C) and Tooling (D) to remove the wear sleeve (if equipped).
Sat May 16 18:48:03 UTC+0800 2020
2/2
2020/5/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01980581
Crankshaft Rear Seal - Install
SMCS - 1161-012
Table 1
Required Tools
E 1U-7598 Seal Installer Gp 1
NOTICE
Note: Replacement rear seals are supplied with a wear sleeve. This wear sleeve must be installed
with the rear seal. New engines from the factory do not have a wear sleeve. Do not install the rear
seal if any of the following conditions exist:
• The crankshaft rear seal has been separated from the wear sleeve.
• The rear seal group appears to be damaged.
• The crankshaft rear seal has been lubricated. The seal is designed to be installed dry.
1. Ensure that the rear of the crankshaft is thoroughly clean and dry prior to the installation of
the crankshaft rear seal.
1/2
2020/5/16

Typical example
2. Use Tooling (E) to install crankshaft rear seal (1).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Sat May 16 18:48:59 UTC+0800 2020
2/2
2020/5/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01987820
Crankshaft Rear Seal Carrier - Remove and Install
SMCS - 1161-010-C3
Removal Procedure
Start By:
a. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
NOTICE
1/4
2020/5/16

1. Remove bolts (1).
2. Remove rear seal carrier (2).
Table 1
Required Tools
A 138-8440 Component Cleaner
B 169-5464 Quick Cure Primer
C 1U-8846 Gasket Sealant
D 9S-3263 Thread Lock Compound
NOTICE
2/4
2020/5/16

1. Clean the joint face of rear seal carrier (2) and the cylinder block with Tooling (A).
2. Apply Tooling (B) to the joint face of rear seal carrier (2). Allow the primer to air dry for
three to five minutes.
Note: Tooling (C) is used on the joint face of rear seal carrier (2). Do not allow the sealant
to get into the oil passage in the mounting face of the cylinder block.
3. Apply Tooling (C) to the joint face of rear seal carrier (2). Spread the sealant uniformly.
Rear seal carrier (2) must be installed within ten minutes of application of the sealant.
4. Position rear seal carrier (2) on the dowels in the rear of the cylinder block.
5. Apply Tooling (D) on the threads of bolts (1). Install bolts (1) that hold rear seal carrier (2)
to the cylinder block.
End By:
a. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
3/4
2020/5/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i04855211
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
2020/5/16

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Fasten Tooling (A) and a suitable lifting device to flywheel housing (1).
2. Remove bolts (2) and bolt (3) that fastens flywheel housing (1) to the cylinder block.
3. Remove flywheel housing (1). The weight of flywheel housing (1) is approximately 32 kg
(70 lb).
Table 2
Required Tools
B 1U-8846 Gasket Sealant 1
NOTICE
2/4
2020/5/16

Correct installation of O-ring seal (3). Do not install the O-ring seal in location (4).
Note: On wet flywheel housings that have rear seal carriers, ensure that the O-ring seal (3)
is installed properly. Improper installation will result in leakage of torque converter oil
between the flywheel housing and the cylinder block.
Note: Ensure that the mating surface of the flywheel housing and the mounting face of the
cylinder block are thoroughly clean.
1. Apply Tooling (B) to the entire mounting face of the flywheel housing prior to installation.
3/4
2020/5/16

2. Fasten Tooling (A) and a suitable lifting device to flywheel housing (1). Position flywheel
housing (1) on the cylinder block. The weight of flywheel housing (1) is approximately
32 kg (70 lb).
3. Install bolts (2) and bolt (3) that fastens flywheel housing (1) to the cylinder block.
4. Remove Tooling (A) and the hoist from flywheel housing (1).
5. Check the flywheel housing runout. Refer to the Systems Operation/Testing and Adjusting,
"Flywheel and Flywheel Housing".
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Sat May 16 18:50:50 UTC+0800 2020
4/4
2020/5/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02370081
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
1. Remove bolts (2), crankshaft vibration damper (1), and the spacers from the crankshaft
pulley.
1/3
2020/5/16

2. Remove belt (3). Refer to Operation and Maintenance Manual, "Belt - Inspect".
3. Remove bolts (4).
4. Remove crankshaft pulley (5).
1. Position crankshaft pulley (5) on the crankshaft. Install bolts (4) and tighten the bolts to a
torque of 160 ± 30 N·m (118 ± 22 lb ft).
2. Install belt (3). Refer to Operation and Maintenance Manual, "Belt - Inspect".
Note: Check the alignment marks on the rubber vibration dampers for proper alignment.
The rubber vibration damper should be replaced if the rubber vibration damper is out of
alignment. Refer to Specifications, "Vibration Damper".
2/3
2020/5/16

3. Install the spacers and crankshaft vibration damper (1). Install bolts (2) and tighten to a
torque of 55 ± 10 N·m (40 ± 7 lb ft).
4. Adjust the tension of the belt. Refer to Specifications, "Belt Tension Chart".
Sat May 16 18:51:46 UTC+0800 2020
3/3
2020/5/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01982085
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
A 1U-7600 Slide Hammer Puller 1
B 1U-8145 Drill Bit 1
Start By:
a. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
1/2
2020/5/16

1. Use Tooling (B) and carefully drill three evenly spaced holes in crankshaft front seal (1).
2. Alternate between the drilled holes and use Tooling (A) to remove crankshaft front seal (1).
Sat May 16 18:52:42 UTC+0800 2020
2/2
2020/5/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01982092
Crankshaft Front Seal - Install
SMCS - 1160-012
Table 1
Required Tools
C 1U-7430 Front Seal Installer 1
NOTICE
1/2
2020/5/16

1. Use Tooling (C) to install crankshaft front seal (1).
Note: The crankshaft seal is designed to be installed dry.
End By:
a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration
Damper and Pulley - Remove and Install".
Sat May 16 18:53:38 UTC+0800 2020
2/2
2020/5/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01379367
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
Start By:
a. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
NOTICE
NOTICE
containing fluids.
Cat products.
1/2
2020/5/16

1. Remove four bolts (1) that fasten bracket (2) on the front of the engine.
2. Remove the bolts (3) and front cover (4) from the front housing.
Sat May 16 18:54:33 UTC+0800 2020
2/2
2020/5/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01379400
Front Cover - Install
SMCS - 1166-012
NOTICE
Note: The rear face of the cover and the front face of the housing must be clean.
1. Inspect the condition of the housing cover gasket. Replace the gasket, if necessary.
1/2
2020/5/16

2. Install the housing cover gasket.
3. Position front cover (4) on the front housing. Install the bolts (3) on front cover (4).
4. Position bracket (2) on the front of the engine.
5. Install four bolts (1) that fasten bracket (2) on the engine.
End By:
a. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Sat May 16 18:55:29 UTC+0800 2020
2/2
2020/5/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01983906
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Remove".
b. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
containing fluids.
Cat products.
1/3
2020/5/16

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

1. Remove front engine support (1).
2/3
2020/5/16

2. Remove belt tightener (2).
3. Remove front housing (3).
Sat May 16 18:56:25 UTC+0800 2020
3/3
2020/5/16

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01983976
Housing (Front) - Install
SMCS - 1151-012
Table 1
Required Tools
A 8T-9011 Component Cleaner 1
B 4C-9500 Quick Cure Primer 1
C 1U-8846 Gasket Sealant 1
1/3
2020/5/16

Caterpillar Cat 325C EXCAVATOR (Prefix BKT) Service Repair Manual (BKT00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 325C EXCAVATOR (Prefix BKT) Service Repair Manual (BKT00001 and up).pdf (18)

More from jdkskmdmdm (20)

Recently uploaded (20)

Caterpillar Cat 325C EXCAVATOR (Prefix BKT) Service Repair Manual (BKT00001 and up).pdf