Caterpillar Cat 325L EXCAVATOR (Prefix 8NK) Service Repair Manual (8NK00001 and up).pdf

Service Repair Manual
Models
325 325L EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 8NK
Configuration: 325, 325L EXCAVATOR 8NK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i03478580
Pistons and Connecting Rods - Install
SMCS - 1225-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
187-1462 Piston Ring Compressor (1)
1
173-5529 Piston Ring Compressor (2)
1
B 4C-5593 Anti-Seize Compound 1
( 1 )
Used for 3114 and 3116 Engines
( 2 )
Used for 3126 Engines
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on reusability of the pistons, refer to the following list.
• Guideline For Reusable Parts And Salvage Operations, SEBF8049, "Pistons"
1/6
325, 325L EXCAVATOR 8NK00001-UP (MACHINE) POWERED BY 3116 ENGIN...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

• Guideline For Reusable Parts And Salvage Operations, SEBF8290, "Visual Inspection of
Two-Piece Pistons"
• Tool Operating Manual, NEHS0775, "Using the 186-0190 Piston Ring Gauge on Steel
Crown, Two-Piece Pistons used in 3126 and 3126B Engines"
Note: For information on reusability of the connecting rods, refer to the following list.
Connecting Rods"
• Guideline For Reusable Parts And Salvage Operations, SEBF8064, "Salvage of Non-
Serrated Connecting Rods"
Note: For information on reusability of the piston pins, refer to the following list.
• Guideline For Reusable Parts And Salvage Operations, SEBF8051, "Piston Pins and
Retaining Rings"
• Guideline For Reusable Parts And Salvage Operations, SEBF8303, "Procedure to Inspect
Piston Pins"
Note: For information on reusability of the rod eye bushing, refer to the following list.
• Guideline For Reusable Parts And Salvage Operations, SEBF8242, "Verification of
Connecting Rod Eye Bushing Retention Using 5P-8639 Connecting Rod Bushing Press
Group"
• Guideline For Reusable Parts And Salvage Operations, SEBF8274, "Using Rod Eye
Bushing Installation and Removal Tools"
Illustration 1 g00678193
1. Install the bolts (5) and the upper half of connecting rod bearing (4) . Ensure that the bearing
tab engages with the slot in connecting rod (3) .
2/6
2020/8/2

2. Install the lower half of connecting rod bearing (4) . Ensure that the bearing tab engages
with the slot in connecting rod cap (2) .
3. Place clean engine oil on the following items: the pistons, the piston rings, the cylinder bore,
the upper half of the connecting rod bearing and the lower half of the connecting rod
bearing.
NOTICE
Install short pieces of rubber hose over both connecting rod bolts in
order to protect the crankshaft from the threaded portion of the
connecting rod bolts.
4. Install short pieces of rubber hose (6) over both connecting rod bolts.
3/6
2020/8/2

Note: Each piston ring end gap must be positioned 120 degrees from each other.
5. Install Tooling (A) in order to compress the piston rings.
6. With the number one crankshaft throw at the bottom center, install the piston and
connecting rod in the engine. Ensure that the proper piston and connecting rod are in the
corresponding cylinder with the bearing retainer notch toward the right side of the engine.
Note: The etched number on the connecting rod must be on the right side of the engine in
the corresponding cylinder.
7. Line up the piston and the connecting rod with the crankshaft. Use a soft hammer and tap
the piston into the cylinder bore until Tooling (A) comes off of the piston.
8. Use a soft hammer in order to tap the piston into the cylinder bore while you guide the
connecting rod onto the crankshaft.
9. Remove the hoses that were installed in Step 4 from the connecting rod bolts.
10. Install connecting rod bearing cap (2) on the connecting rod (3) . Ensure that the number on
connecting rod bearing cap (2) matches the number on the connecting rod (3) . Ensure that
the numbers are on the same side.
4/6
2020/8/2

11. Lubricate connecting rod cap bolts with Tooling (B) .
NOTICE
Loose connecting rod nuts can result in the separation of the rod cap
and result in major engine damage.
Note: Later connecting rods will have bolts in place of the bolts and nuts.
12. Install connecting rod cap nuts (1) . Tighten nuts (1) to the torque that is specified in Table
2.
Table 2
Torque Specifications
Machined Connecting
Rods
Tighten nuts (1) to a torque of 54 ± 7 N·m (40 ± 5 lb ft) plus an
additional 60 ± 5 degrees.
Fractured Connecting
Rods
Tighten nuts (1) to a torque of
70 ± 5 N·m (52 ± 4 lb ft) plus an additional 120 ± 5 degrees.
13. Repeat Steps 1 through 12 for the remaining pistons and connecting rods.
End By:
a. Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets -
Remove and Install".
5/6
2020/8/2

b. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
c. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 2 17:15:49 UTC+0800 2020
6/6
2020/8/2

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i03706818
Crankshaft Main Bearings - Remove
SMCS - 1203-011
Removal Procedure
Table 1
Required Tools
A 2P-5518 Bearing Tool 1
Start By:
a. Remove the engine balancer shaft on 3114 engines. Refer to Disassembly and Assembly,
"Engine Balancer Shaft - Remove and Install".
b. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
1/3
2020/8/2

1. Remove bolts (1) that hold crankshaft main bearing cap (2). Remove crankshaft main
bearing cap (2).
2. Remove the lower half of the crankshaft main bearing from crankshaft main bearing cap (2).
NOTICE
If the crankshaft is turned in the wrong direction, the tab of the
crankshaft main bearing will be pushed between the crankshaft and
the cylinder block. this can cause damage to either or both the
crankshaft and the cylinder block.
Note: Some crankshaft main bearing journals do not have an oil hole. Place a thin piece of
soft material that will not damage the journal against the end of the bearing. Ensure that the
material is on the opposite side of the bearing tab. Hit the bearing with the soft material until
the bearing tab is free from the bearing tab groove in the cylinder block.
3. Use the following steps in order to remove the upper half of crankshaft main bearings:
2/3
2020/8/2

a. Turn the crankshaft until Tooling (A) can be installed in the crankshaft journal. Install
Tooling (A).
b. Turn the crankshaft in order to remove the upper half of the crankshaft main bearing.
In order to get the tab out first, the crankshaft must be turned in the correct direction.
c. Check the condition of the crankshaft main bearings. Refer to the Guideline For
Reusable Parts, SEBF8009, "Main and Connecting Rod Bearings" and Guideline For
Reusable Parts, SEBV0544, "Engine Bearings and Crankshafts".
Sun Aug 2 17:16:45 UTC+0800 2020
3/3
2020/8/2

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i06542070
Crankshaft Main Bearings - Install
SMCS - 1203-012
Table 1
Required Tools
A 2P-5518 Bearing Tool 1
B 8T-5096 Dial Indicator Group 1
NOTICE
Note: For information on the reusability of the crankshaft main bearings, refer to the Guideline
For Reusable Parts And Salvage Operations, SEBF8009, "Main and Connecting Rod Bearings".
Note: Place clean engine oil on the crankshaft main bearings prior to assembly. The tabs on the
back side of the crankshaft main bearings must fit in the grooves of main bearing caps and the
cylinder block.
1/4
2020/8/2

1. Use Tooling (A) and install the upper halves of the crankshaft main bearings in the cylinder
block. Do not put oil on the back of the crankshaft main bearing.
2. Install the lower halves of the crankshaft main bearings in crankshaft main bearing caps (2).
Do not put oil on the back of the crankshaft main bearing.
2/4
2020/8/2

Six-cylinder engine with oil grooves in the cylinder block
Six-cylinder engine with no oil grooves in the cylinder block
NOTICE
Crankshaft main bearing caps should be installed with the part
number toward the right side of the engine. Crankshaft main bearing
caps are to be identified by stamped numbers 1 through 7 located on
the bottom surface. The thrust plate is to be installed in the original
position on the crankshaft main bearing.
3. Oil grooves are machined in the saddles of the cylinder blocks of all 3114 engines and
earlier 3116 engines. No oil grooves are machined in the saddles of the cylinder block on
later 3116 engines and all 3126 engines.
4. Install the bearing caps with the bearing tabs on the same side. A six cylinder engine has an
order of 1 through 7 (front to rear). A four cylinder engine has an order of 1 through 5 (front
to rear). Place crankshaft main bearing caps (2) in position on the cylinder block. Place
clean engine oil or Molylube on the bolt threads and the washer face. Install bolts (1).
5. Tighten bolts (1) to a torque of 54 ± 7 N·m (40 ± 5 lb ft). Tighten each bolt (1) for an
additional 90 ± 5 degrees (1/4 turn).
3/4
2020/8/2

6. Check the end play of the crankshaft with Tooling (B). The end play must be 0.07 mm
(0.003 inch) to 0.32 mm (0.013 inch).
End By:
a. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
b. Install the engine balancer shaft on 3114 engines. Refer to Disassembly and Assembly,
"Engine Balancer Shaft - Remove and Install".
Sun Aug 2 17:17:41 UTC+0800 2020
4/4
2020/8/2

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01935937
Crankshaft - Remove
SMCS - 1202-011
Removal Procedure
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
b. Remove the crankshaft seal carrier. Refer to Disassembly and Assembly, "Crankshaft Rear
Seal Carrier - Remove and Install".
c. Remove the front gear group. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove".
d. Remove the piston and the connecting rods. Refer to Disassembly and Assembly, "Piston
and Connecting Rods-Remove".
NOTICE
NOTICE
1/3
2020/8/2

Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: For information on reusability of the crankshaft, refer to the following list.
• Guideline For Reusable Parts And Salvage Operations, SEBF8041, "Crankshaft
Measurement"
• Guideline For Reusable Parts And Salvage Operations, SEBF8054, "Procedure to Measure
and Straighten Bent Crankshafts"
• Guideline For Reusable Parts And Salvage Operations, SEBF8094, "Procedure to Grind
Crankshafts"
Crankshafts"
• Guideline For Reusable Parts And Salvage Operations, SEBF8039, "Inspection of
Crankshafts for Cracks"
• Guideline For Reusable Parts And Salvage Operations, SEBF8042, "Procedure to Polish
Crankshafts"
Note: For information on reusability of the crankshaft main bearings, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8009, "Main and Connecting Rod Bearings".
Note: For information on reusability of the cylinder block and salvage procedures, refer to the
following list.
• Guideline For Reusable Parts And Salvage Operations, SEBF8192, "Specifications and
Salvage for Cylinder Blocks on 3114, 3116, and 3126 Engines"
• Guideline For Reusable Parts And Salvage Operations, SEBF8261, "Installing a 7C-6208
Cylinder Sleeve in 3114, 3116 Engines and a 107-7604 Cylinder Sleeve in 3126 Engines"
• Special Instruction, SEHS8869, "Cylinder Block Salvage Procedure Using Belzona Ceramic
R Metal"
• Special Instruction, GMG00981, "Using 1P-3537 Dial Bore Gauge Group to Check
Cylinder Bore Size"
• Special Instruction, SMHS7606, " Use of 1P-4000 Line Boring Tool Group"
• Special Instruction, SEHS8841, " Using the Ironstitch Procedure for Casting Salvage"
2/3
2020/8/2

• Special Instruction, SEHS8919, "Salvage Weld Procedure for Cast Iron Cylinder Blocks"
• Guideline For Reusable Parts And Salvage Operations, SEBF8076, "Specifications to
Salvage Cylinder Block Contact Surfaces"
Note: The weight of the crankshaft for the 3114 Engine is 37 kg (82 lb). The weight of the
crankshaft for 3116 and 3126 Engines is 62 kg (137 lb).
1. Use a suitable lifting device. Remove bolts (2), the washers and main bearing caps (3).
Carefully remove crankshaft (1) from the cylinder block.
2. Remove upper main bearing (4) from the cylinder block.
3. Remove the main bearings from the main bearing caps.
Sun Aug 2 17:18:37 UTC+0800 2020
3/3
2020/8/2

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i06249742
Crankshaft - Install
SMCS - 1202-012
Table 1
Required Tools
A 8T-5096 Dial Indicator Group 1
NOTICE
NOTICE
Ensure that the crankshaft main bearing tabs engage with the grooves
in the block and the crankshaft main bearing cap.
Note: For information on reusability of the crankshaft, refer to the following list.
1/5
2020/8/2

• Guideline For Reusable Parts And Salvage Operations, SEBF8041, "Crankshaft
Measurement"
• Guideline For Reusable Parts And Salvage Operations, SEBF8054, "Procedure to Measure
and Straighten Bent Crankshafts"
• Guideline For Reusable Parts And Salvage Operations, SEBF8094, "Procedure to Grind
Crankshafts"
Crankshafts"
• Guideline For Reusable Parts And Salvage Operations, SEBF8039, "Inspection of
Crankshafts for Cracks"
• Guideline For Reusable Parts And Salvage Operations, SEBF8042, "Procedure to Polish
Crankshafts"
Note: For information on reusability of the cylinder block and salvage procedures, refer to the
following list.
• Guideline For Reusable Parts And Salvage Operations, SEBF8192, "Specifications and
Salvage for Cylinder Blocks on 3114, 3116, and 3126 Engines"
• Guideline For Reusable Parts And Salvage Operations, SEBF8261, "Installing a 7C-6208
Cylinder Sleeve in 3114, 3116 Engines and a 107-7604 Cylinder Sleeve in 3126 Engines"
• Special Instruction, SEHS8869, "Cylinder Block Salvage Procedure Using Belzona Ceramic
R Metal"
• Special Instruction, GMG00981, "Using 1P-3537 Dial Bore Gauge Group to Check
Cylinder Bore Size"
• Special Instruction, SMHS7606, " Use of 1P-4000 Line Boring Tool Group"
• Special Instruction, SEHS8841, " Using the Ironstitch Procedure for Casting Salvage"
• Special Instruction, SEHS8919, "Salvage Weld Procedure for Cast Iron Cylinder Blocks"
• Guideline For Reusable Parts And Salvage Operations, SEBF8076, "Specifications to
Salvage Cylinder Block Contact Surfaces"
1. Check the condition of the crankshaft main bearings. Refer to the Guideline For Reusable
Parts, SEBF8009, "Main and Connecting Rod Bearings" and Guideline For Reusable Parts,
SEBV0544, "Engine Bearings and Crankshafts".
Note: The number four main bearing in 3114 Engines is the thrust bearing. The number six
main bearing in the six cylinder engines is the thrust bearing.
2. Clean the bearing surfaces in the cylinder block for the main bearings.
2/5
2020/8/2

3. Install the upper main bearings (4) in the cylinder block. Ensure that the tab on the back side
of the bearing engages with the groove in the cylinder block. Apply clean engine oil on the
upper main bearing. Do not put engine oil on the back side of the bearing surfaces.
Typical example
4. Put clean engine oil on the journals of the crankshaft bearing. Fasten lifting straps and a
hoist to crankshaft (1) . Carefully install the crankshaft in the cylinder block.
5. Clean the bearing surface of the main bearing caps.
3/5
2020/8/2

6. Install the lower main bearings (5) in the crankshaft main bearing caps (3) . Ensure that the
tab on the back side of the bearing engages with the groove in the main bearing cap. Apply
clean engine oil on the lower main bearing. Do not put engine oil on the back side of the
bearing surfaces.
7. Install crankshaft main bearing caps with the bearing tabs on the same side. Ensure that
crankshaft main bearing caps have numbers 1 through 7. The numbers should start at the
front of the engine. Place clean engine oil or Molylube on the bolt threads and the washers.
Note: When the bolts for the rear main bearing cap are tightened, slide the main bearing cap
as far forward as possible until the cap is against the bolts. Hold the main bearing cap in this
position and tighten the bolts.
Typical example
8. Install bolts (2) and the washers for main bearing caps (3) . Tighten bolts (2) to a torque of
54 ± 7 N·m (40 ± 5 lb ft).
9. Turn bolts (2) for an additional 90 ± 5 degrees (1/4 turn).
4/5
2020/8/2

Typical example
10. Check the end play of crankshaft (1) with Tooling (A) . The end play must be 0.07 mm
(0.003 inch) to 0.32 mm (0.013 inch).
End By:
a. Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and
Connecting Rods - Install".
b. Install the front gear group. Refer to Disassembly and Assembly, "Gear Group (Front) -
Install".
c. Install the crankshaft seal carrier. Refer to Disassembly and Assembly, "Crankshaft Rear
Seal Carrier- Remove and Install".
d. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Sun Aug 2 17:19:32 UTC+0800 2020
5/5
2020/8/2

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01944203
Crankshaft Gear - Remove and Install
SMCS - 1204-010-GE
Removal Procedure
Start By:
a. Remove the front gear group. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove".
NOTICE
Note: For information on reusability of the camshaft gear, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
1. Place alignment marks on the crankshaft gear and on the crankshaft. The alignment marks
will ensure that the camshaft gear is aligned properly during installation.
1/3
2020/8/2

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

2. Heat crankshaft gear (1). Remove crankshaft gear (1) from crankshaft (2).
NOTICE
Note: For information on reusability of the camshaft gear, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
1. Heat crankshaft gear (1) to a maximum temperature of 204 °C (400 °F) for no longer than 1
hour for installation.
2. Align the timing marks on the crankshaft and on crankshaft gear (1). Install crankshaft gear
(1) on crankshaft (2).
2/3
2020/8/2

Note: Ensure that crankshaft gear (1) is flush against the shoulder of crankshaft. If the gear
is not flush damage to the gear may occur.
End By:
a. Install the front gear group. Refer to Disassembly and Assembly, "Gear Group (Front) -
Install".
Sun Aug 2 17:20:28 UTC+0800 2020
3/3
2020/8/2

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i05977048
Bearing Clearance - Check
SMCS - 1203-535; 1219-535
Measurement Procedure
Table 1
Required Tools
A
198-9142
Plastic Gauge (Green)
0.025 to 0.076 mm
(0.001 to 0.003 inch)
1
198-9143
Plastic Gauge (Red)
0.051 to 0.152 mm
(0.002 to 0.006 inch)
1
198-9144
Plastic Gauge (Blue)
0.102 to 0.229 mm
(0.004 to 0.009 inch)
1
198-9145
Plastic Gauge (Yellow)
0.230 to 0.510 mm
(0.009 to 0.020 inch)
1
Note: Plastic gauge may not be necessary when the engine is in the chassis.
NOTICE
1/3
2020/8/2

Caterpillar Cat 325L EXCAVATOR (Prefix 8NK) Service Repair Manual (8NK00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 325L EXCAVATOR (Prefix 8NK) Service Repair Manual (8NK00001 and up).pdf(13)

More from fuusejkddmmd3e(20)

Recently uploaded(20)

Caterpillar Cat 325L EXCAVATOR (Prefix 8NK) Service Repair Manual (8NK00001 and up).pdf