Caterpillar cat 326 d2 l excavator (prefix hm4) service repair manual (hm400001 and up)

Service Repair Manual
Models
326D2 and 326D2 L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR HM4
Configuration: 326D2 L OEM HM400001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03124522
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 in) long 1
B
8T-0651 Bolt 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
1/11
326D2 L OEM HM400001-UP (MACHINE) POWERED BY C7.1 Engine(M0078112...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
2/11
2020/9/19

4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
6. Remove O-ring seal (3) , port plate (4) , and bearing (5) .
7. Remove O-ring seals (6) . Remove springs (7) .
3/11
2020/9/19

This is an example of the use of Tooling (B) .
8. Place a shop towel over brake piston (8) . Retain brake piston (8) with Tooling (B) . Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y) . Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
4/11
2020/9/19

9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
11. Remove plates (13) and friction discs (14) .
5/11
2020/9/19

12. Install Tooling (C) into shaft (15) . Use a prybar to remove the rotating assembly (16) from
the housing.
13. Remove Tooling (C) from shaft (15) .
14. Remove shaft (15) from rotating assembly (16) .
6/11
2020/9/19

15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
17. Rotate shaft (15) . Install shaft (15) into a suitable press. Install Tooling (E) . Remove
bearing race (19) from shaft (15) .
7/11
2020/9/19

18. Remove cam plate (20) from barrel assembly (21) .
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
8/11
2020/9/19

20. Remove ball (23) and springs (24) .
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
9/11
2020/9/19

25. Remove bolts (29) and cover (30) .
26. Remove seal (31) and backup ring (32) .
27. Remove piston actuator (33) and seal (34) .
10/11
2020/9/19

28. Remove O-ring seal (35) from the housing of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 19 17:13:06 UTC+0800 2020
11/11
2020/9/19

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07505849
Travel Motor - Disassemble
SMCS - 4351-015
S/N - DTG1-UP
S/N - EBP1-UP
S/N - FEX1-UP
S/N - HM41-UP
S/N - LCW1-UP
S/N - LJE1-UP
Disassembly Procedure
Table 1
Required Tools
A
1P-2420 Transmission Repair Stand 1
FT-0957 Positioning Gp 4
B
- M16x2 Threaded Rod 3
8T-1757 Nut 6
9X-8268 Washer 6
C 421-5662 Lifting Eye Assembly 1
D 421-5663 Lifting Eye Assembly 2
E 1U-9895 Crossblock 1
1/13
2020/9/19

3H-0465 Push-Puller Plate 2
8T-0298 Bolt 2
Start By:
a. Remove the travel motor.
1. Attach the travel motor to Tooling (A) and (B). The weight of the travel motor is
approximately 70 kg (154 lb).
2. Remove plugs (1) and the O-ring seals.
3. Remove plug (2) and the O-ring seal. Repeat for the opposite side.
2/13
2020/9/19

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove plug (2A) and the O-ring seal. Repeat for the opposite side.
5. Remove spring (3).
3/13
2020/9/19

6. Remove spool (4).
4/13
2020/9/19

7. Remove bolts (5) and cap (6). Repeat for the opposite side.
8. Remove O-ring seal (10) from cap (6). Remove guide (9), spring (8), and washer (7) from
the head assembly. Repeat for the opposite side.
9. Remove plug (11), O-ring seal (12), spring (13), and ball (14) from cap (6). Repeat for the
other cap.
5/13
2020/9/19

10. Remove spool (15).
11. Remove relief valve (16). Remove O-ring seal (17) from relief valve (16).
12. Repeat for the opposite side.
6/13
2020/9/19

13. Remove the nuts of Tooling (B). Remove bolts (19) from head assembly (18).
14. Use Tooling (C) and a suitable lifting device to remove head assembly (18). The weight of
head assembly (18) is approximately 21 kg (47 lb).
7/13
2020/9/19

15. Remove control plate (20) and bearing (21) from head assembly (18).
16. Remove pins (22) and springs (23).
17. Remove O-ring seals (24) and (25).
18. Use Tooling (D) and a suitable lifting device to remove housing assembly (26) from
Tooling (A) and place on a suitable bench.
8/13
2020/9/19

To avoid personal injury, always wear eye and face protection when
using pressurized air.
19. Attach Tooling (E) to housing (26). Use air pressure to unseat brake piston (27). Remove
Tooling (E) and brake piston (27).
20. Remove back up rings (28) and O-ring seals (29) from brake piston (27).
9/13
2020/9/19

21. Remove brake piston guide (30).
22. Remove O-ring seal (31) from brake piston guide (30).
10/13
2020/9/19

Note: Note the orientation of friction discs (32) and plates (33) for assembly purposes.
23. Remove friction discs (32) and plates (33).
24. Remove rotating group (34) from housing (26).
25. Remove pistons (35) and retainer (36) from barrel (37).
11/13
2020/9/19

26. Remove hold down ball (38) and springs (39) from barrel (37).
27. Remove swashplate (40) from housing (26).
12/13
2020/9/19

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

28. Remove pistons (41).
29. Remove springs (42) and shaft (43).
30. Remove balls (46).
31. Remove bearing (44) and lip seal (45).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 19 17:14:01 UTC+0800 2020
13/13
2020/9/19

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i03124523
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
A
1U-7506 Adapter 1
8T-4244 Nut 6
- Threaded Rod M12 x 1.75 X 250 mm (10 in) long 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G 9S-3263 Thread Lock Compound -
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
1/11
2020/9/19

must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
1. Install O-ring seal (35) onto the housing of the travel motor.
2. Install seal (34) and piston actuator (33) .
2/11
2020/9/19

Caterpillar cat 326 d2 l excavator (prefix hm4) service repair manual (hm400001 and up)

More Related Content

What's hot (9)

Similar to Caterpillar cat 326 d2 l excavator (prefix hm4) service repair manual (hm400001 and up) (20)

More from fjjskdmnenemm (20)

Recently uploaded (20)

Caterpillar cat 326 d2 l excavator (prefix hm4) service repair manual (hm400001 and up)