Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml00001 and up)

Service Repair Manual
Models
330-A L, 330, 330L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 9ML
Configuration: 330, 330L TRACK-TYPE EXCAVATORS 9ML00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00894497
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2244 Pump Extractor 1
B 6V-4186 Fuel Pump Timing Pin 1
C 8T-5287 Wrench 1
D
6V-9128 Rack Position Tool Group
1
3S-3270 Indicator Contact Point 1
C-clamp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/10/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Illustration 1 g00507964
1. Install spacer (1) in the fuel injection pump housing.
2. Install Tool (B) in the fuel injection pump housing. Move the rack until Tool (B) can be
installed in order to hold the rack in the center position. The rack must be in the center
position in order to install the fuel injection pumps.
2/4(W)
w
2020/10/8

3. Turn the camshaft until the lobe of the camshaft is downward so that the fuel injection pump
can be installed.
4. Install Tool (A) on the bonnet of the fuel injection pump.
5. Install the fuel injection pump in the fuel injection pump housing. Ensure that slot (3) that is
cut in the gear is aligned with the small pin (2) and groove (4) in the barrel. The small pin
(2) and groove (4) in the barrel are aligned with dowel (5) in the fuel injection pump
housing.
6. Put clean engine oil on O-ring seal (6) and install the O-ring seal in the fuel injection pump
housing.
7. Install bushing (7) by hand until the bushing is even with the top of the fuel injection pump
housing. If bushing (7) cannot be installed by hand, remove bushing (7). Remove the fuel
injection pump. Put the pump in alignment and reinstall bushing (7) .
8. Install Tool (C) on bushing (7) and tighten the bushing to a torque of 163 ± 14 N·m (120 ±
10 lb ft).
3/4(W)
w
2020/10/8

9. Install Tool (D) in order to measure the total travel of the rack. The correct travel for the
rack is 15.70 mm (.618 inch). A smaller measurement is an indication of improper fuel
injection pump installation.
10. Repeat Steps 1 through 9 in order to install the remaining fuel injection pumps.
11. Install the cover and the gasket on the fuel injection pump housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 8 13:13:16 UTC+0800 2020
4/4(W)
w
2020/10/8

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01117604
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2(W)
w
2020/10/8

1. Remove bolt (2) and the clamp that holds the oil supply tube and the oil drain tube in
position.
2. Remove two bolts (1) that hold the oil supply tube to the turbocharger. Remove two bolts
(3) that hold the oil drain tube to the turbocharger.
3. On the 3304B, loosen the two hose clamps and remove the hose from the turbocharger.
Slide the hose onto the pipe that goes to the cylinder head.
4. Loosen nut (4) and remove the oil supply tube from the engine.
5. Loosen four bolts (6) and the nuts that hold turbocharger (5) to the exhaust manifold.
Remove turbocharger (5) and the gasket from the exhaust manifold. Remove oil drain tube
(7) from the engine and check the O-ring seal for damage. If the O-ring seal is worn or
damaged, use a new part for replacement.
Thu Oct 8 13:14:12 UTC+0800 2020
2/2(W)
w
2020/10/8

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01009195
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Table 1
Required Tools
A 9S-6363 Turbocharger Fixture Group 1
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
1/2(W)
w
2020/10/8

1. Install the turbocharger onto Tool (A) .
2. Apply alignment marks to the two housings and the cartridge assembly for correct
alignment during assembly.
3. Loosen clamp (3) and remove compressor housing (4) from cartridge assembly (2) .
4. Loosen the remaining clamp on turbine housing (1) and remove cartridge assembly (2) from
the turbine housing.
Thu Oct 8 13:15:07 UTC+0800 2020
2/2(W)
w
2020/10/8

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01009564
Turbocharger - Assemble
SMCS - 1052-016
Assembly Procedure
Table 1
Required Tools
A 9S-6363 Turbocharger Fixture Group 1
NOTICE
1/2(W)
w
2020/10/8

1. Put cartridge assembly (2) in position on turbine housing (1). Make sure that the
identification marks are in alignment. Tighten the clamp that secures cartridge assembly (2)
to turbine assembly (1) to a torque of 14 ± 1.1 N·m (125 ± 10 lb in).
2. Put compressor housing (4) in position on cartridge assembly (2). Make sure that the
identification marks are in alignment. Tighten clamp (3) that secures compressor housing
(4) to cartridge assembly (2) to a torque of 14 ± 1.1 N·m (125 ± 10 lb in).
3. Remove the turbocharger from Tool (A) .
Thu Oct 8 13:16:03 UTC+0800 2020
2/2(W)
w
2020/10/8

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01117656
Turbocharger - Install
SMCS - 1052-012
NOTICE
Note: Check the condition of the gaskets and the O-ring seals. If the gaskets or the O-ring
seals are worn or damaged, use new parts for replacement.
1/2(W)
w
2020/10/8

1. Install oil drain tube (7) on the engine. Position the gasket and turbocharger (5) on top of the
exhaust manifold and install four bolts (6) and the nuts.
2. Install the gasket and two bolts (3) that hold the oil drain tube to the turbocharger. Put the
oil supply tube in position and install the gasket and two bolts (1) that hold the oil supply
tube to the turbocharger. Tighten nut (4) .
3. On the 3304B, slide the hose into position on the turbocharger and the pipe that goes to the
cylinder head. Tighten the hose clamp.
4. Install the clamp that holds the oil supply tube and the oil drain tube in position and install
bolt (2) .
Thu Oct 8 13:16:59 UTC+0800 2020
2/2(W)
w
2020/10/8

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01041426
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
1/5(W)
w
2020/10/8

1. Remove two nuts (1), the washers and the heat shield from the exhaust manifold.
2. Remove bolt (3) from the bracket that holds two of the fuel injection lines in position.
Loosen nuts (2) and (4) and remove the two fuel injection lines from the engine. Put
protective caps on the fuel injectors and put protective caps on the fuel injection pump in
order to prevent contamination.
3. Remove the remaining ten exhaust manifold nuts (5) and the large washers. Remove
exhaust manifold (6).
2/5(W)
w
2020/10/8

4. Remove three exhaust manifold gaskets (7) from the cylinder head and the twelve exhaust
manifold studs, if necessary. Make sure that the position of the two longer studs are marked
for proper installation.
Table 1
Required Tools
Tool Part Number Description Qty
A 5P-0144 Fuel Line Socket 1
NOTICE
1. If the twelve exhaust manifold studs were removed, apply 5P-3931 Anti-Seize Compound
to both ends of the exhaust manifold studs and install the studs in the cylinder head. Make
sure that the two longer studs are installed in the correct position. Tighten the studs to a
torque of 27 ± 4 N·m (20 ± 3 lb ft).
3/5(W)
w
2020/10/8

2. Put three exhaust manifold gaskets (7) in position on the cylinder head.
3. Install exhaust manifold (6). Install ten washers and nuts (5). The two longer studs are for
the installation of the heat shield. Tighten exhaust manifold nuts (5) to a torque of 47 ± 4
N·m (35 ± 3 lb ft).
4/5(W)
w
2020/10/8

4. Remove the protective caps from the fuel injectors and the fuel injection pump. Put the fuel
injection lines in position and tighten nuts (2) and (4) finger tight. Install bolt (3) in the
bracket that holds the fuel injection lines in position. Tighten nuts (3) and (4) with Tool (A)
to a torque of 40 ± 7 N·m (30 ± 5 lb ft).
5. Install the two large washers and the spacers on the two remaining exhaust manifold studs.
Install heat shield (1) and the remaining two washers and exhaust manifold nuts that fasten
heat shield (1) to the exhaust manifold. Tighten the two nuts to a torque of 47 ± 4 N·m (35 ±
3 lb ft).
6. Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel system -
Prime" topic (Maintenance Section).
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Thu Oct 8 13:17:55 UTC+0800 2020
5/5(W)
w
2020/10/8

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i00962627
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
A 5S-1330 Valve Spring Compressor 1
B 8S-2263 Valve Spring Tester 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and assembly, "Cylinder Head - Remove".
NOTICE
1/4(W)
w
2020/10/8

1. Use Tool (A) to compress valve spring (2) and remove valve keepers (1) .
2. Remove Tool (A), the rotocoil, the valve spring and the valve stem oil shield. Remove the
valve from the cylinder head. Put identification marks on the valves for installation
purposes.
3. Check the valve spring force with Tool (B). Refer to Specifications, "Cylinder Head
Valves" for information on the valve springs.
4. Perform Steps 1 through 3 for the remaining inlet and exhaust valves.
Table 2
Required Tools
A 5S-1330 Valve Spring Compressor 1
B 5S-1322 Valve Keeper Inserter 1
2/4(W)
w
2020/10/8

NOTICE
1. Lubricate the inlet and exhaust valves with clean engine oil. Install the inlet and exhaust
valves in the original location in the cylinder head.
2. Install valves (3), oil shield (4), valve spring (2) and rotocoil (1) in the cylinder head.
3. Use Tool (A) to compress valve spring (2). Install valve keeper (5) on the valve stem with
Tool (B) .
3/4(W)
w
2020/10/8

The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
4. Carefully remove Tool (A). Strike the top of the valve with a soft faced hammer in order to
ensure that the valve keepers are properly installed.
5. Repeat Steps 3 through 4 for the remaining inlet and exhaust valves.
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove
and Install".
Thu Oct 8 13:18:50 UTC+0800 2020
4/4(W)
w
2020/10/8

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i00962891
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
A 9U-7349 Valve Guide Driver 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
1/3(W)
w
2020/10/8

1. Use Tool (A) to remove the inlet and exhaust valve guides from the cylinder head.
2. Repeat Step 1 for the remaining inlet and exhaust valve guides.
Table 2
Required Tools
A 9U-7349 Valve Guide Driver 1
B 9U-6954 Valve Guide Collar 1
NOTICE
2/3(W)
w
2020/10/8

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

1. Put clean engine oil on the outside diameter of the valve guide. Install the valve guide with
Tool (A) and Tool (B), as shown.
2. Dimension (X) from the top of the valve guide to the cylinder head must be 22.23 ± 0.25
mm (0.875 ± 0.010 inch). For more information on the inlet and exhaust valve guides, refer
to Specifications, "Cylinder Head Valves".
Note: In order to help prevent damage to the valve guides, Tool (B) must be used during
installation.
3. Repeat Steps 1 and 2 for the remaining inlet and exhaust valve guides.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Thu Oct 8 13:19:46 UTC+0800 2020
3/3(W)
w
2020/10/8

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02107684
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
A 6V-4805 Valve Seat Extractor Tool Group 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
NOTICE
1/3(W)
w
2020/10/8

1. Use Tooling (A) in order to remove the valve seat insert from the cylinder head.
2. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
3. Repeat Steps 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
Table 2
Required Tools
A 6V-4805 Valve Seat Extractor Tool Group 1
NOTICE
2/3(W)
w
2020/10/8

Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml00001 and up)

More Related Content

What's hot (11)

Similar to Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml00001 and up) (17)

More from fikkskmmdm (20)

Recently uploaded (20)

Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml00001 and up)