Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr00001 and up)

Service Repair Manual
Models
330B L and 330B LN Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B L EXCAVATOR 3YR
Configuration: 330B L, 330B LN Excavators 3YR00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00921612
Compression Brake - Install
SMCS - 1119-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00471010
1. Install Compression Brake (B) and oil tube (4) .
2. Install Compression Brake (A) .
1/2(W)
w
2020/9/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

3. Connect wires (3) and (2). Install four bolts (1) .
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 30 12:37:16 UTC+0800 2020
2/2(W)
w
2020/9/30

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i00999978
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
1/2(W)
w
2020/9/30

1. Remove six bolts (3) and rocker shaft assembly (2). Remove the O-ring seal from the rear
rocker shaft support.
2. Put identification marks on pushrods (1) in order to identify the location of the pushrods in
the engine. Remove pushrods (1) from the engine. Repeat this process for each pushrod.
Wed Sep 30 12:38:12 UTC+0800 2020
2/2(W)
w
2020/9/30

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01001004
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Start By:
A. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrods - Remove".
NOTICE
1/3(W)
w
2020/9/30

1. Remove O-ring seal (1) from the rear support bracket.
Note: Replace the O-ring seal when the head bolt is removed from the rear rocker shaft
support.
2. Remove retainer ring (6), washer (5), spring (4), washer (3) and rocker arm (2). Note the
number of washers (3) that are used at both ends of the shaft. Remove rocker arms (2) from
each end of the rocker shaft.
3. Remove the pin from the rear rocker shaft support (7) with a hammer and a suitable punch.
Remove rear rocker shaft support (7) .
4. Remove the remaining rocker arms, springs, washers and rocker shaft supports.
5. Remove the plugs from each end of the shaft, if necessary.
Wed Sep 30 12:39:08 UTC+0800 2020
2/3(W)
w
2020/9/30

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01138110
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2020/9/30

1. Install rocker arms (4), supports (1), washer (5) and springs (2) on the rocker shaft.
2. Install rear rocker shaft support (6) on the rocker shaft. Ensure that the hole in the rear
rocker shaft support is aligned with the hole in the rocker shaft.
3. Install pin (3) through the rocker shaft support and the rocker shaft with a hammer.
4. Pin (3) must extend 9.60 mm (.378 inch) above the rocker shaft support.
2/3(W)
w
2020/9/30

5. Install O-ring seal (7). Install rocker arm (4), washer (8), springs (9), washer (10) and
retainer ring (11) .
Note: Make sure that the correct number of washers (8) are installed on the shaft.
6. Install the plugs in each end of the rocker shaft if the plugs were removed.
End By: Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrods - Install".
Wed Sep 30 12:40:03 UTC+0800 2020
3/3(W)
w
2020/9/30

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07085956
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
NOTICE
1. Loosen adjusting screws (3). This will prevent a bent valve or a bent pushrod during the
installation of the rocker shaft assembly. Install pushrods (2) and ensure that the pushrods
are seated in the valve lifters.
1/3(W)
w
2020/9/30

2. Install rocker shaft assembly (1) in position on the cylinder head.
NOTICE
Ensure that the dowels on each end of the rocker shaft assembly are in
alignment with the holes in the cylinder head.
3304B torque sequence
2/3(W)
w
2020/9/30

Note: Replace the O-ring seal when the bolt toward the rear of the engine is installed in the
rocker shaft support.
3. Apply 6V-4876 Lubricant on the threads of six bolts (4) except for the bolt that passes
through the rear rocker shaft support (bolt (6) in Illustration 3). Install six bolts (4) in the
rocker shaft assembly.
4. Refer to Illustration 3. Tighten six bolts (4) for the rocker shaft, as follows:
a. Tighten all the bolts in the numerical sequence to a torque of 155 N·m (115 lb ft).
b. Tighten all the bolts in the numerical sequence to a torque of 250 ± 17 N·m
(185 ± 13 lb ft).
c. Tighten all the bolts again in the numerical sequence to a final torque of
250 ± 17 N·m (185 ± 13 lb ft).
5. The assembled length of the springs at both ends of the rocker shaft must be 1.50 ± 0.25 mm
(.059 ± .010 inch). Remove the washers or install the washers behind the springs to change
the assembled length of the springs.
6. Adjust the inlet valve lash to 0.38 ± 0.08 mm (.015 ± .003 inch) and adjust the exhaust valve
lash to 0.64 ± 0.08 mm (.025 ± .003 inch). Refer to Testing and Adjusting, "Air Inlet and
Exhaust System" for more information on setting the valve lash. Tighten the locknuts for the
adjusting screws (3) to a torque of 29 ± 7 N·m (21 ± 5 lb ft). Refer to Specifications, "Valve
Rocker Arms and Lifters".
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Wed Sep 30 12:40:59 UTC+0800 2020
3/3(W)
w
2020/9/30

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i00991114
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
B. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
C. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrods - Remove".
NOTICE
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4(W)
w
2020/9/30

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1. Loosen hose clamp (2) on the hose that connects the oil cooler to water pump elbow (1) .
2. Remove two bolts (3) that fasten water pump elbow (1) to the cylinder head. Remove two
bolts (4) that fasten water pump elbow (1) to the water pump.
3. Carefully remove water pump elbow (1) and the gaskets from the engine.
2/4(W)
w
2020/9/30

4. Disconnect tube (5) from the inlet manifold.
5. Remove four bolts (6) and remove air inlet pipe (7) .
3/4(W)
w
2020/9/30

NOTICE
Do not set the cylinder head on a hard, flat surface. Damage may occur
to the fuel injection nozzle tips.
6. Remove all bolts (8) and (9) that hold the cylinder head to the cylinder block.
7. Attach the proper lifting device in order to remove cylinder head (10) from the engine.
Remove cylinder head (10) from the engine. The weight of cylinder head (10) is
approximately 95 kg (210 lb).
Wed Sep 30 12:41:55 UTC+0800 2020
4/4(W)
w
2020/9/30

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07489822
Cylinder Head - Install
SMCS - 1100-012
NOTICE
Note: When the cylinder head is removed, a new spacer plate gasket must be installed. Refer to
Disassembly and Assembly, "Spacer Plate - Remove and Install".
1. Ensure that the surface of the cylinder head is clean and dry. Install a new dry cylinder head
gasket onto the cylinder block.
1/5(W)
w
2020/9/30

2. Fasten the proper lifting device to cylinder head (1). Put cylinder head (1) in position on the
cylinder block. Remove the lifting device after cylinder head (1) is positioned.
3. Apply clean engine oil to the threads and the washer faces of cylinder head bolts (2) and (3).
Install cylinder head bolts (2) and (3). Tighten the cylinder head bolts finger tight.
Note: Do not tighten the cylinder head bolts at this time.
4. Install pushrods (4). Make sure that the pushrods are installed in the original location and
that the pushrods are seated correctly in the valve lifters.
5. Loosen the adjusting screws on rocker arms (5) for valve clearance. This will prevent a bent
valve or a broken pushrod during installation.
6. Install a new O-ring seal in the rear rocker arm support.
7. Apply clean engine oil to all the rocker shaft bolts except bolt (25). Refer to illustration 5.
8. Put rocker shaft assembly (5) in position on the cylinder head. Make sure that the dowels in
the rocker shaft supports are aligned with the dowel holes in the cylinder head.
9. Ensure that the rocker arms are aligned with the pushrods and install the rocker shaft
mounting bolts. Tighten the rocker shaft mounting bolts finger tight.
2/5(W)
w
2020/9/30

10. Tighten the cylinder head bolts by hand, as follows:
a. Tighten all the bolts (1 through 18) in the numerical sequence to a torque of
150 ± 15 N·m (115 ± 12 lb ft).
b. Tighten all the bolts (1 through 18) again in the numerical sequence to a torque of
250 ± 17 N·m (185 ± 13 lb ft).
c. Tighten all the bolts (1 through 18) again in the numerical sequence to a final torque
of 250 ± 17 N·m (185 ± 13 lb ft).
d. Tighten all the remaining bolts (A through E) to a torque of 43 ± 7 N·m (32 ± 5 lb ft).
3/5(W)
w
2020/9/30

11. Tighten the cylinder head bolts by hand, as follows:
a. Tighten all the bolts (1 through 26) in the numerical sequence to a torque of
150 ± 15 N·m (115 ± 12 lb ft).
b. Tighten all the bolts (1 through 26) in the numerical sequence to a torque of
250 ± 17 N·m (185 ± 13 lb ft).
c. Tighten all the bolts (1 through 26) again in the numerical sequence to a final torque
of 250 ± 17 N·m (185 ± 13 lb ft).
d. Tighten all the remaining bolts (A through G) to a torque of 43 ± 7 N·m (32 ± 5 lb ft).
12. Adjust the inlet valve lash to 0.38 mm (.015 inch) and the exhaust valve lash to 0.64 mm
(.025 inch). Tighten the locknuts for the adjusting screws to a torque of 29 ± 7 N·m
(22 ± 5 lb ft). Refer to the Testing and Adjusting, "Air Inlet and Exhaust System" topic for
additional information on valve lash adjustments.
13. Put the gasket and air inlet pipe (7) in position on the cylinder head. Install four bolts (6) to
fasten air inlet pipe (7) to the cylinder head.
4/5(W)
w
2020/9/30

14. Connect tube (8) to the inlet manifold.
15. Put the gaskets and water pump elbow (11) in position on the engine. Install two bolts (9)
that fasten water pump elbow (11) to the cylinder head. Install two bolts (10) that fasten
water pump elbow (11) to the water pump.
16. Tighten hose clamp (12).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
b. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
c. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Wed Sep 30 12:42:51 UTC+0800 2020
5/5(W)
w
2020/9/30

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01045029
Spacer Plate - Remove and Install
SMCS - 1221-010
Removal Procedure
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
1/4(W)
w
2020/9/30

1. Remove O-ring seal (1), water seals (3) and water directors (4) from spacer plate (2) .
NOTICE
Do not damage the dowels as the spacer plate is removed.
2. Remove spacer plate (2) from the cylinder head.
3. Remove O-ring seal (6) and spacer plate gasket (5) from the cylinder head.
2/4(W)
w
2020/9/30

NOTICE
1. Thoroughly clean the mating surfaces between the spacer plate and the cylinder block.
2. Install new spacer plate gasket (5) and new O-ring seal (6) .
Note: If the dowels in the cylinder block have been removed for any reason, the overall
height of the installation is 16.0 ± 5.0 mm (.63 ± .20 inch).
Note: Both surfaces of the spacer plate, spacer plate gasket and the top of the cylinder block
must be clean and dry. Do not use any gasket adhesive or other substances on these
surfaces.
3/4(W)
w
2020/9/30

Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr00001 and up)

More Related Content

Similar to Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr00001 and up) (18)

More from fikkskkdmmd (20)

Recently uploaded (20)

Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr00001 and up)