Caterpillar cat 330 d l excavator (prefix edx) service repair manual (edx00001 and up)

Service Repair Manual
Models
330D and 330D L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR EDX
Configuration: 330D & 330D L Excavators EDX00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i06939513
Swing Drive - Assemble
SMCS - 5459-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-5197 Pliers 1
B 138-7574 Link Brackets 2
C 138-7575 Link Bracket 3
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/10(W)
w
2020/8/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Illustration 1 g00869899
1. Install lip seals (32) and O-ring seal (33) in bearing cage (29).
Note: Lubricate the seals and the seal surface of the shaft before you install the cage
assembly.
2. Carefully install cage (29) on shaft (31).
3. Raise the temperature of bearing (36) to 135 °C (275 °F) and use two people to install the
bearing on shaft (31). The weight of bearing (36) is approximately 35 kg (77 lb).
4. Install spacer (35) on shaft assembly (31). Install the spacer with relief against bearing (36).
2/10(W)
w
2020/8/19

5. Raise the temperature of bearing (34) to 135 °C (275 °F). Install the bearing on shaft (31)
and against spacer (35).
6. Use Tooling (A) to install retaining ring (28) on shaft (31) and against bearing (34).
7. Install shaft assembly (31) in swing drive housing (16).
3/10(W)
w
2020/8/19

a. Apply 5P-3931 Anti-Seize Compound on the inside diameter of swing drive housing
(16).
b. Lower the temperature of shaft assembly (31).
c. Attach Tooling (C) and a suitable lifting device to the shaft assembly.
d. Install the shaft assembly into swing drive housing (16). Bearing (34) must be within
the bore of the swing drive housing.
e. Remove Tooling (C) and the suitable lifting device from the shaft assembly. Attach
Tooling (C) and the suitable lifting device to the swing drive housing.
f. Lift the swing drive vertically. Use a hammer and a drift to align bearing (34) in the
lower bore of the swing drive housing. When the bearing is properly aligned in the
bore, shaft assembly (31) will drop into the proper position within the swing drive
housing.
8. Apply 1U-8846 Sealant on the threads of bolts (30).
9. Install bolts (30) and washers in bearing cage (29) and swing drive housing (16).
4/10(W)
w
2020/8/19

10. Install bearings (24) and (26) in gear (25).
11. Install gear (25) and washers (23) and (27) in carrier (20).
12. Lower the temperature of shaft (22). Install the shaft in carrier assembly (20).
13. Install pin (21) in the carrier assembly and the shaft.
14. Use a hammer and a center punch to stake the pin in the carrier housing.
15. Repeat Steps 10 through Steps 14 on the remaining gear assemblies.
16. Use a suitable lifting device to install carrier assembly (20). The weight of carrier assembly
(20) is approximately 68 kg (150 lb).
5/10(W)
w
2020/8/19

17. Install retaining ring (19).
18. Install spacer (17) in carrier assembly (18).
19. Make sure that the mating surfaces of ring gear (15) and swing drive housing (16) are
thoroughly clean.
6/10(W)
w
2020/8/19

20. Apply 1U-8846 Gasket Sealant to the face of swing drive housing (16) and the face of ring
gear (15).
21. Use Tooling (B) and a suitable lifting device to install ring gear (15) in swing drive housing
(16). The weight of ring gear (15) is approximately 80 kg (175 lb).
22. Install retaining ring (14) into the sun gear.
23. Install sun gear (13) in carrier assembly (4). Install upper retaining ring (12).
24. Assemble carrier assembly (4).
7/10(W)
w
2020/8/19

a. Apply clean SAE 30W oil on bearing (10). Install bearing (10) in planetary gear (9).
b. Install thrust washer (8) on one side of planetary gear (9).
c. Install thrust washer (11) on the other side of planetary gear (9).
d. Use a deburring tool to remove the metal burr from the openings in the carrier.
e. Install planetary gear (9) and the thrust washers in carrier assembly (4).
f. Install planetary shaft (7) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
8/10(W)
w
2020/8/19

g. Drive spring pin (6) into shaft (7). Orient the split in spring pin (6) vertically to the
carrier. Align the split in the spring pin to the top or the bottom. Make a stake mark
on each side of the spring pin hole in the carrier. Each stake mark should be
approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside diameter of the
spring pin hole.
h. Repeat Steps 24.a through 24.g to install the other three planetary gears in the carrier.
25. Use two people to install carrier assembly (4) in the ring gear. The weight of the carrier
assembly is approximately 36 kg (80 lb).
26. Install spacer (5) in carrier assembly (4).
27. Install sun gear (3) in carrier assembly (4).
9/10(W)
w
2020/8/19

28. Make sure that the mating surfaces of the ring gear and cover (2) are thoroughly clean.
29. Apply 1U-8846 Gasket Sealant on the flange surface of the ring gear and cover (5).
30. Install cover (2) and bolts (1).
End By:
a. Install the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Aug 19 12:34:27 UTC+0800 2020
10/10(W)
w
2020/8/19

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07192381
Swing Drive - Install
SMCS - 5459-012
Installation Procedure
Table 1
Required Tools
A
132-8223 110 volt Power Pack 1
1U-6221 Torque Wrench 1
132-8143 36 mm Hex Link 1
B 439-3939 Link Bracket As 4
C -
Forcing Bolt
M24 x 3 by 5 inch
2
D - Loctite C5A Copper Anti-Seize -
E 1U-8846 Gasket Sealant 1
1. Apply Tooling (D) on the locating pin and the pin bore in the main frame. Apply Tooling
(E) on the mating surface of the main frame and the swing drive housing.
1/3(W)
w
2020/8/19

2. Attach Tooling (B) and a suitable lifting device to swing drive (2), as shown. The weight of
swing drive (2) is approximately 510 kg (1125 lb). Install swing drive (2) into the original
position. Be careful not to damage the pinion gear.
Note: During installation, the locating pin for the swing drive can come out of the swing
drive housing. The locating pin can be installed with a hammer after the swing drive is in
place.
3. Use Tooling (A) to install bolts (1) that secure the swing drive to the main frame.
4. Before assembly, remove compound, oil, and dust from female threads, then apply Tooling
(D) to the threads of bolts (1).
5. Tighten bolts (1) in an alternating sequence to a torque of 250 ± 25 N·m (184 ± 18 lb ft).
Turn an additional angle of 45 ± 5 degrees. Refer to Service Magazine , M0083843 , "An
Improved Bolt Tightening Procedure for the Critical Joints Is Now Used on all Excavators"
for more detailed information.
6. Fill the swing drive with oil. Refer to Operation and Maintenance Manual, "Swing Drive Oil
- Change".
End By:
2/3(W)
w
2020/8/19

a. Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install"
.
Wed Aug 19 12:35:29 UTC+0800 2020
3/3(W)
w
2020/8/19

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02386587
Swing Gear and Bearing - Remove
SMCS - 7063-011
Removal Procedure
Table 1
Required Tools
A 138-7576 Link Bracket 4
B
132-8223 Hydraulic Pump and Motor (115 V 50/60 Hz Single Phase)(1)
1
1U-6221 Hydraulic Torque Wrench 1
132-8143 36 mm Hex Link 1
(1)
132-8231 Hydraulic Pump and Motor (220 V 50/60 Hz Single Phase) is also available.
Start By:
a. Remove the undercarriage frame. Refer to Disassembly and Assembly, "Upper Frame and
Undercarriage Frame - Separate".
1. Remove all of the grease from the swing gear and bearing. Put the grease in a suitable
container for storage or disposal.
1/3(W)
w
2020/8/19

2. Put an alignment mark on swing gear and bearing (1) and on the undercarriage frame
assembly for assembly purposes. Attach Tooling (A) and a suitable lifting device to swing
gear and bearing (1), as shown. Apply slight lifting tension to the swing gear and bearing.
3. Use Tooling (B) in order to remove bolts (2) and the spacers that hold swing gear and
bearing (1) to the undercarriage frame.
4. Remove swing gear and bearing (1). The weight of the swing gear and bearing (1) is
approximately 280 kg (615 lb).
2/3(W)
w
2020/8/19

Note: Inner dust seal (3) and outer dust seal (4) may have been installed dry in the swing
gear and bearing or inner dust seal (3) and outer dust seal (4) may have been bonded to the
swing gear and bearing.
5. Remove inner dust seal (3) and outer dust seal (4) from the swing gear and bearing.
6. Clean the seal grooves of the inner dust seal and the outer dust seal with a fine grit
sandpaper. Use a cleaning solvent to clean the sealing grooves. Make sure that the seal
grooves are thoroughly clean and dry prior to installing the new dust seals.
Wed Aug 19 12:36:32 UTC+0800 2020
3/3(W)
w
2020/8/19

Shutdown SIS
Previous Screen
Product: EXCAVATOR
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
i07191587
Swing Gear and Bearing - Install
SMCS - 7063-012
Installation Procedure
Table 1
Required Tools
A 439-3941 Link Bracket As 4
B
132-8223 Hydraulic Pump and Motor (115 V 50/60 Hz Single Phase)(1)
1
1U-6221 Hydraulic Torque Wrench 1
132-8143 36 mm Hex Link 1
C - Loctite 435 -
D 2P-9066 Lubricant 1
E 1U-8846 Gasket Sealant 1
F - Loctite C5A Copper Anti-Seize -
(1)
132-8231 Hydraulic Pump and Motor (220 V 50/60 Hz Single Phase) is also available.
Note: If the inner dust seal (3) and the outer dust seal (4) are installed dry, the new dust seals should
be installed dry in the swing gear and bearing.
Note: If the inner dust seal and the outer dust seal are bonded to the swing gear and bearing, the new
dust seals should be bonded to the swing gear and bearing.
Note: Perform Steps 1.a through 1.j to install the new dry dust seals.
Note: Perform Steps 2.a through 2.p to install the new dust seals that are bonded to the swing gear
and bearing.
1/6(W)
w
2020/8/19

1. If inner dust seal (3) and outer dust seal (4) were installed dry, use the following procedure to install
the new dust seals:
a. Use a wire brush to thoroughly clean the grooves for the dust seal of the swing gear and
bearing. Make sure that all the dirt and foreign material has been removed.
b. Wash the grooves for the dust seal in a suitable solvent that will not leave an oily residue.
c. Make sure that the grooves for the dust seal in the swing gear and bearing are thoroughly clean
and dry prior to installation of the dust seals.
d. Cut one end of inner dust seal (3) at a 90 degree angle. Use a blunt tool to install the inner dust
seal in the seal groove of the swing gear and bearing.
e. Install the seal so that the lip of the seal is facing in the direction that is shown. Refer to
Illustration 1.
f. After the inner dust seal is installed in the seal groove, measure the seal and cut the remaining
end of the inner dust seal at a 90 degree angle. Install the remaining end of the inner dust seal
in the seal groove.
g. Make sure that the inner dust seal is seated properly in the seal groove, all the way around the
swing gear and bearing. Also, make sure that there is no gap between the ends of the inner dust
seal.
h. Pull each end of the inner dust seal out of the seal groove of the swing gear and bearing
approximately 50.8 mm (2.00 inch). Apply Tooling (C) to each end of the inner dust seal to
bond the seals together.
i. Immediately reinstall the inner dust seal in the seal groove of the swing gear and bearing.
Again, make sure that the entire inner dust seal is properly seated in the seal groove of the
swing gear and bearing. No gap should exist between the ends of the inner dust seal.
j. To ensure that the lip of inner dust seal has not adhered to the top of the bearing at the seal
joint, run a dull putty knife between the lip of the seal and the bearing at the seal joint.
k. Follow the procedure in Steps 1.a through 1.j to install outer dust seal (4) in the swing gear and
bearing. Refer to Illustration 1 for proper seal orientation in the swing gear and bearing.
2/6(W)
w
2020/8/19

2. If inner dust seal (3) and outer dust seal (4) were bonded in the swing gear and bearing, use the
following procedure to install the new dust seals:
a. Thoroughly clean all the dirt and foreign material from the grooves for the dust seal in the
swing gear and bearing with a wire brush.
b. Wash the grooves for the dust seal in a suitable solvent that will not leave an oily residue.
c. Make sure that the grooves for the dust seals in the swing gear and bearing are thoroughly
clean and dry prior to installation of the dust seals.
Note: Install inner dust seal (3) and outer dust seal (4) in the swing gear and bearing in small
increments, because Tooling (C) cures very quickly.
d. Cut one end of inner dust seal (3) at a 90 degree angle.
e. Start applying Tooling (C) 50.8 mm (2.00 inch) from the cut end of the seal. Apply Tooling
(C) to the seal in 152.4 mm (6.00 inch) increments.
f. Immediately use a blunt tool to install only the bonded portion of the inner dust seal in the seal
groove of the swing gear and bearing. Make sure that the dust seal is seated properly in the
seal groove.
g. Install the seal so that the lip of the seal is facing in the direction that is shown. Refer to
Illustration 1.
h. To ensure that the inner dust seal has not adhered to the bearing, run a dull putty knife between
the lip of the seal and the bearing.
i. Apply Tooling (C) to the next 152.4 mm (6.00 inch) of the seal. Immediately use a blunt tool
to install only the bonded portion of the inner dust seal in the seal groove of the swing gear and
bearing.
j. Make sure that the inner dust seal is seated properly in the seal groove. Ensure that the inner
dust seal has not adhered to the bearing.
Note: Do not install the last 152.4 mm (6.00 inch) of the inner dust seal.
k. Repeat Steps 2.i through 2.j until the dust seal is installed.
l. Measure the inner dust seal and cut the remaining end of inner dust seal (3) at a 90 degree
angle. Install the last 152.4 mm (6.00 inch) of seal in the seal groove dry.
m. Make sure that the inner dust seal is properly seated in the seal groove and that there is no gap
between the seal ends. Carefully remove both loose ends of the inner dust seal out of the seal
groove.
n. Apply Tooling (C) to the loose ends of the seal.
o. Immediately use a blunt tool to reinstall the seal ends in the seal groove. Again, make sure that
the inner dust seal is properly seated in the seal groove, and that no gap existed between the
ends of the seal.
p. To ensure that the inner dust seal has not adhered to the top of the bearing, run a dull putty
knife around the seal.
q. Follow the procedure in Steps 2.a through 2.p to install outer dust seal (4) in the swing gear
and bearing. Refer to Illustration 1 for proper seal orientation in the swing gear and bearing.
3. Lubricate the swing gear and bearing with grease.
3/6(W)
w
2020/8/19

Note: Clean the mating surface for the swing gear and bearing on the undercarriage frame assembly.
4. Apply Tooling (E) on the mating surface for the swing gear and bearing of the undercarriage frame
assembly.
5. Fasten Tooling (A) and a suitable lifting device to swing gear and bearing (1), as shown. Refer to
Illustration 2. The weight of swing gear and bearing (1) is approximately 660 kg (1455 lb).
6. Place the swing gear and bearing in the swing gear and bearing's original position on the
undercarriage frame assembly.
7. Make sure that the stamp "S" on the inner race is in the position that is shown, relative to the
undercarriage frame assembly and the stopper on the outer race. Refer to Illustration 3.
4/6(W)
w
2020/8/19

8. Apply a thin coat of Tooling (F) on the threads of bolts (2). Install the spacers and bolts (2) that
secure the swing gear and bearing to the undercarriage frame assembly.
Note: Some machines use bolts that are plated with Dacromet. Dacromet bolts appear silver, gray in
color. Do not apply Tooling (F) to the threads of Dacromet bolts. Make sure that the bolt holes are
clean and dry when Dacromet bolts are used.
Note: Torque for bolts (2) is 1000 ± 125 N·m (738 ± 92 lb ft) on 345 excavators.
Note: Torque for bolts (2) is 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional angle of 55 ± 5
degrees on 336 excavators.
9. Use Tooling (B) to tighten bolts (2) to a torque of 900 ± 100 N·m (665 ± 75 lb ft).
10. Refer to Service Magazine , M0083843 , "An Improved Bolt Tightening Procedure for the Critical
Joints Is Now Used on all Excavators" for more detailed information.
NOTICE
Improper lubrication can cause damage to machine components.
To avoid damage, make sure that the proper amount of grease is
applied to the swing drive.
When the amount of grease in the compartment becomes too large, the
agitation loss becomes large, thereby accelerating grease deterioration.
Grease deterioration can cause damage to the pinion gear of the swing
drive and swing internal gear.
Not enough grease will result in poor gear lubrication.
11. Add Tooling (D) to the swing gear and bearing after the installation.
Reference: Refer to Operation and Maintenance Manual, "Refill Capacities" for the capacity of the
swing gear and bearing.
Reference: Refer to Operation and Maintenance Manual, "Swing Gear - Lubricate" for lubricating
the swing gear and bearing.
5/6(W)
w
2020/8/19

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Reference: Refer to Operation and Maintenance Manual, "Maintenance Interval Schedule" for the
schedule for lubricating the swing gear and bearing.
End By:
a. Install the undercarriage frame assembly. Refer to Disassembly and Assembly, "Undercarriage
Frame - Install" in this manual.
Wed Aug 19 12:37:35 UTC+0800 2020
6/6(W)
w
2020/8/19

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02451315
Oil Filter (Hydraulic, Return) - Remove
SMCS - 5068-011
Removal Procedure
Table 1
Required Tools
A 138-7575 Link Bracket 1
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
1. Drain the hydraulic oil into a suitable container for storage or disposal. Refer to Operation
and Maintenance Manual, "Hydraulic Oil - Change".
1/3(W)
w
2020/8/19

2. Remove bolts (1) and reposition filter assembly (2).
3. Disconnect hose assemblies (4). Remove bolts (3). Reposition filter assembly (5) out of the
way.
4. Remove bolts (6) from pipe assembly (7).
2/3(W)
w
2020/8/19

Caterpillar cat 330 d l excavator (prefix edx) service repair manual (edx00001 and up)

More Related Content

What's hot (9)

Similar to Caterpillar cat 330 d l excavator (prefix edx) service repair manual (edx00001 and up) (12)

More from jfdjskmdmme (20)

Recently uploaded (20)

Caterpillar cat 330 d l excavator (prefix edx) service repair manual (edx00001 and up)