Abstract image of a woman sitting on books and studying on a laptop

Caterpillar cat 330 d l excavator (prefix ern) service repair manual (ern00001 and up)

J
jfdjskmdmme

This document provides the disassembly procedure for a final drive on excavator models 330D and 330D L. It involves removing 32 components in 31 steps, including removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Special tools are required to remove components and many components are heavy, requiring two people or lifting devices to remove safely due to weights from 32 kg to 550 kg. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.

Automotive
1 of 26
Download to read offline
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Service Repair Manual Models 330D and 330D L Excavator
Disassembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1P-2420 Transmission Repair Stand 1 B 138-7573 Link Bracket 2 C 1P-1863 Retaining Ring Pliers 1 D 208-6033 Spanner Socket 1 E 138-7574 Link Bracket 2 F 5F-7366 Forcing Screw 1 1P-5546 Crossblock 1 1U-9889 Crossblock 1 1P-0520 Driver Group 1 6V-7888 Puller Leg 2 1H-3112 Puller Assembly 1 1P-5551 Adjustable Screw Assembly 1 G 1U-7600 Slide Hammer Puller Gp 1 8T-0266 Bolt 1 Start By: A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove". Note: Cleanliness is an important factor. Before the disassembly procedure, the thoroughly clean the exterior of the component. This will prevent dirt from entering the internal mechanism. Note: Some of the images that are in this procedure do not show the sprocket assembly that is attached to the final drive housing. If necessary, the weights that are given include the weight of the sprocket assembly. 1. Put an alignment mark across the sections of the final drive for assembly purposes. The parts must be reinstalled in the part's original locations. 2/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 1 g00708089 2. Fasten the final drive to Tooling (A) , as shown. The weight of the final drive assembly is approximately 312 kg (688 lb). 3. Remove bolts (1) and the washers that hold the cover in position. Illustration 2 g00708090 4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to cover (2) , as shown. Remove the cover. The weight of the cover is approximately 32 kg (70 lb). 3/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 3 g00879362 5. Remove bolts (3) . Remove gear (5) . Check plate (6) . Replace plate (6) if wear is shown. Remove plugs (4) from cover (2) . Illustration 4 g00879365 6. Remove O-ring seal (7) from plugs (4) . Illustration 5 g00780428 4/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Remove gear (8) . Remove spacer (9) . Illustration 6 g00780432 8. Remove retaining ring (10) with Tooling (C) . Remove washer (11) . Remove gear (12) . Remove bearing assembly (13) . Remove second washer (11) . 9. Repeat Step 8 for the remaining two gear assemblies. Illustration 7 g00781401 10. Remove retaining ring (14) . 5/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 8 g00781407 11. Remove carrier assembly (15) . Illustration 9 g01389593 12. Use a suitable press in order to remove the shafts from carrier assembly (15) . 6/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 10 g00781412 13. Remove gear (16) . Remove spacer (17) . Illustration 11 g00781466 14. Remove retaining ring (18) . 15. Remove carrier assembly (19) . Illustration 12 g00879368 7/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Disassemble carrier assembly (19) , as follows. a. Drive spring pin (20) into planetary shaft (21) with a hammer and a punch. Illustration 13 g00781476 b. Remove planetary shaft (21) . c. Remove spring pin (20) from planetary shaft (21) with a hammer and a punch. Illustration 14 g00781516 d. Remove thrust washers (22) and planetary gear (24) from the carrier assembly. e. Remove bearing (23) from planetary gear (24) . 17. Repeat Steps 16.a through 16.e for the other two planetary. 8/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 15 g00781529 18. Remove gear (25) . Remove spacer (26) . Illustration 16 g00781559 19. Remove carrier assembly (27) . 20. Use two people to remove carrier assembly (27) . The weight of the carrier assembly is approximately 38 kg (85 lb). 21. Disassemble carrier assembly (27) , as follows. 9/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 17 g00781719 a. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch. Illustration 18 g00781601 b. Remove planetary shaft (28) . c. Remove spring pin (29) from planetary shaft (28) with a hammer and a punch. Illustration 19 g00781607 d. Remove thrust washers (30) and planetary gear (32) from the carrier assembly. e. Remove two bearings (31) from the planetary gear. 22. Repeat Steps 21.a through 21.e for the other two planetary gears. 10/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 20 g00781730 23. Use two people to remove gear (33) . The weight of gear is approximately 41 kg (90 lb). Illustration 21 g00781807 24. Remove O-ring seal (34) . Illustration 22 g01147650 25. Remove bolts (35A) and plates (35B) . 11/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 23 g01147651 26. Use Tooling (G) to remove dowel (37) from stopper plate (35) . Illustration 24 g01147759 27. Secure Tooling (D) to stopper plate (35) . Use Tooling (D) to remove stopper plate (35) . 12/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 25 g01147930 28. Use Tooling (E) and a suitable lifting device to remove housing (36) . The weight of housing (36) is approximately 100 kg (220 lb). Illustration 26 g01147951 29. Remove Duo-Cone seal (39A) from housing (38) . Illustration 27 g01147975 13/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 28 g01147934 30. Remove Duo-Cone seal (39B) from housing (36) . 31. Use Tooling (F) in order to remove bearings (40) and (41) from housing (36) . 32. If necessary, remove the final drive sprocket from the sprocket housing. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Mon Aug 17 14:05:20 UTC+0800 2020 14/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Shutdown SIS Previous Screen Product: EXCAVATOR Model: 330D L EXCAVATOR ERN Configuration: 330D Excavator ERN00001-UP (MACHINE) POWERED BY C-9 Engine Disassembly and Assembly 330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit Machine Systems Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018 i06252413 Final Drive - Disassemble - Type-Two SMCS - 4050-015 S/N - B6H568-UP S/N - DTS1-UP S/N - EAH1-UP S/N - EDX1-UP S/N - EFT1-UP S/N - ERN275-UP S/N - FAR1-UP S/N - FFK1-UP S/N - GGE1-UP S/N - GGH1-UP S/N - HHK1-UP S/N - J2F1-UP S/N - JBT1-UP S/N - JLP299-UP S/N - JTN1-UP S/N - JWR1-UP 1/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
S/N - KDJ1-UP S/N - LMG1-UP S/N - LRM1-UP S/N - M3M1-UP S/N - M3N1-UP S/N - M4T1-UP S/N - MDS1-UP S/N - MEY179-UP S/N - MPL1-UP S/N - MWP1-UP S/N - MYG1-UP S/N - MYP1-UP S/N - NBD169-UP S/N - NBN1-UP S/N - PGW1-UP S/N - PPN1-UP S/N - PRF1-UP S/N - PTB1-UP S/N - RAS573-UP S/N - T2Y226-UP S/N - THJ1-UP S/N - TLY1-UP S/N - W3K1-UP S/N - WDC1-UP S/N - WET1-UP S/N - WRK1-UP 2/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
S/N - XBH1-UP S/N - YCF1-UP S/N - ZCT1-UP S/N - ZML1-UP Disassembly Procedure Table 1 Required Tools Tool Part Number Part Description QTY A 439-3940 Link Brackets 3 B 439-3939 Link Bracket 2 C 154-6183 Forcing Bolts 3 Start By: A. Remove the final drive and the travel motor. 1. Put an alignment mark across the sections of the final drive for assembly purposes. The parts must be reinstalled in the original locations. Illustration 1 g02151790 Note: The weight of the entire final drive assembly is approximately 550 kg (1200 lb). 2. Attach Tooling (A) and a suitable lifting device to cover (2) . The weight of cover (2) is approximately 32 kg (70 lb). Remove bolts (1) and cover (2) . 3/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 2 g00879362 3. Remove bolts (3) . Remove gear (5) . Remove plate (6) . Remove plugs (4) from cover (2) . Illustration 3 g00879365 4. Remove O-ring seal (7) from plugs (4) . 4/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 4 g02151806 5. Remove sun gear (8) , spacer (9) , and planetary gear assembly (10) . Illustration 5 g02151809 6. Remove retaining ring (11) , washer (12) , planetary gear (13) , roller bearing (15) , and washer (16) from carrier assembly (17) . 7. Repeat Step 6 for the remaining two gear assemblies. 8. Remove retaining ring (14) and sun gear (18) from carrier assembly (17) . 5/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 6 g02152150 9. Use a suitable press to remove the shafts from carrier assembly (17) . Illustration 7 g02151813 10. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (19) . The weight of planetary gear assembly (19) is approximately 48 kg (105 lb). Remove planetary gear assembly (19) . 11. Remove spacer (20) . 6/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 8 g02151782 12. Drive spring pin (21) into planetary shaft (22) with a suitable hammer and a suitable punch. 13. Remove planetary shaft (22) , washer (24) , roller bearing (25) , planetary gear (26) , and washer (27) from the planetary gear assembly (19) . 14. Remove spring pin (21) from planetary shaft (22) with a suitable hammer and a suitable punch. 15. Remove retaining ring (23) and sun gear (28) from planetary gear assembly (19) . Illustration 9 g02152208 7/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (29) . The weight of planetary gear assembly (29) is approximately 38 kg (85 lb). Remove planetary gear assembly (29) . Illustration 10 g02152467 17. Drive spring pin (30) into planetary shaft (31) with a suitable hammer and a suitable punch. 18. Remove planetary shaft (31) , washer (32) , roller bearings (33) , planetary gear (34) , and washer (35) from the planetary gear assembly (29) . 19. Remove spring pin (30) from planetary shaft (31) with a suitable hammer and a suitable punch. 8/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 11 g02152399 20. Attach Tooling (A) and a suitable lifting device to ring gear (36) . The weight of ring gear (36) is approximately 66 kg (146 lb). Remove ring gear (36) . 21. Remove O-ring seal (37) from sprocket housing (38) . Illustration 12 g02152525 Illustration 13 g02152528 Note: Mark the orientation of coupling gear (40) for assembly purposes. 22. Remove bolts (39) from coupling gear (40) . Use Tooling (C) in order to remove coupling gear (40) from the motor housing. 9/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
Illustration 14 g02152546 23. Remove shims (41) from the motor housing. Illustration 15 g02152552 Note: Upper bearing cone (42) and lower bearing cone (43) are a slip fit on the motor housing. While you remove sprocket housing (38) from the motor housing, upper bearing cone (42) may stay with the sprocket housing, or upper bearing cone (42) may stay on the motor housing. 24. Attach Tooling (B) and a suitable lifting device to sprocket housing (38) . The weight of sprocket housing (38) is approximately 109 kg (240 lb). Remove sprocket housing (38) and upper bearing cone (42) . 10/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
Illustration 16 g02152595 25. Remove dowels (45) from the motor housing. 26. Remove Duo-Cone seal (44) from the motor housing. 27. If lower bearing cone (43) remained on the motor housing, then remove the lower bearing cone. Illustration 17 g02152598 28. Remove Duo-Cone seal (46) from the sprocket housing. 29. If upper bearing cone (42) remained on the sprocket housing, then remove the upper bearing cone. 30. Remove the bearing cups from the sprocket housing. (Type 1) Disassembly Procedure Table 2 Required Tools Tool Part Number Part Description Qty 11/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

More Related Content

PDF
Caterpillar cat 330 d excavator (prefix nbd) service repair manual (nbd00001 ...
hhjsekmdmm
 
PDF
Caterpillar cat 330 d excavator (prefix thj) service repair manual (thj00001 ...
hhjsekmdmm
 
PDF
Caterpillar cat 330 d l excavator (prefix jlp) service repair manual (jlp0000...
hhjsekmdmm
 
PDF
Caterpillar cat 329 dl excavator (prefix mnb) service repair manual (mnb00001...
udjjjskkdmme
 
PDF
Caterpillar cat 330 d2 l excavator (prefix szk) service repair manual (szk000...
fjskkksmemm
 
PDF
Caterpillar cat 324 d l excavator (prefix tsn) service repair manual (tsn0000...
jfksekmmdme
 
PDF
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...
jfdjskmdmme
 
PDF
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...
jfdjskmdmme
 
Caterpillar cat 330 d excavator (prefix nbd) service repair manual (nbd00001 ...
hhjsekmdmm
 
Caterpillar cat 330 d excavator (prefix thj) service repair manual (thj00001 ...
hhjsekmdmm
 
Caterpillar cat 330 d l excavator (prefix jlp) service repair manual (jlp0000...
hhjsekmdmm
 
Caterpillar cat 329 dl excavator (prefix mnb) service repair manual (mnb00001...
udjjjskkdmme
 
Caterpillar cat 330 d2 l excavator (prefix szk) service repair manual (szk000...
fjskkksmemm
 
Caterpillar cat 324 d l excavator (prefix tsn) service repair manual (tsn0000...
jfksekmmdme
 
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...
jfdjskmdmme
 
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...
jfdjskmdmme
 

More from jfdjskmdmme (20)

PDF
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 l excavator (prefix hsp) service repair manual (hsp000...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 l excavator (prefix her) service repair manual (her000...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex000...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 l excavator (prefix ex7) service repair manual (ex7000...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 l excavator (prefix ebp) service repair manual (ebp000...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 l excavator (prefix dtg) service repair manual (dtg000...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 excavator (prefix xdr) service repair manual (xdr00001...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 excavator (prefix hsp) service repair manual (hsp00001...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 excavator (prefix her) service repair manual (her00001...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 excavator (prefix fex) service repair manual (fex00001...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 excavator (prefix ex7) service repair manual (ex700001...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 excavator (prefix ebp) service repair manual (ebp00001...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d2 excavator (prefix dtg) service repair manual (dtg00001...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d l excavator (prefix thj) service repair manual (thj0000...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d l excavator (prefix nbd) service repair manual (nbd0000...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d l excavator (prefix mwp) service repair manual (mwp0000...
jfdjskmdmme
 
PDF
Caterpillar cat 330 d l excavator (prefix mey) service repair manual (mey0000...
jfdjskmdmme
 
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...
jfdjskmdmme
 
Caterpillar cat 330 d2 l excavator (prefix hsp) service repair manual (hsp000...
jfdjskmdmme
 
Caterpillar cat 330 d2 l excavator (prefix her) service repair manual (her000...
jfdjskmdmme
 
Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex000...
jfdjskmdmme
 
Caterpillar cat 330 d2 l excavator (prefix ex7) service repair manual (ex7000...
jfdjskmdmme
 
Caterpillar cat 330 d2 l excavator (prefix ebp) service repair manual (ebp000...
jfdjskmdmme
 
Caterpillar cat 330 d2 l excavator (prefix dtg) service repair manual (dtg000...
jfdjskmdmme
 
Caterpillar cat 330 d2 excavator (prefix xdr) service repair manual (xdr00001...
jfdjskmdmme
 
Caterpillar cat 330 d2 excavator (prefix hsp) service repair manual (hsp00001...
jfdjskmdmme
 
Caterpillar cat 330 d2 excavator (prefix her) service repair manual (her00001...
jfdjskmdmme
 
Caterpillar cat 330 d2 excavator (prefix fex) service repair manual (fex00001...
jfdjskmdmme
 
Caterpillar cat 330 d2 excavator (prefix ex7) service repair manual (ex700001...
jfdjskmdmme
 
Caterpillar cat 330 d2 excavator (prefix ebp) service repair manual (ebp00001...
jfdjskmdmme
 
Caterpillar cat 330 d2 excavator (prefix dtg) service repair manual (dtg00001...
jfdjskmdmme
 
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...
jfdjskmdmme
 
Caterpillar cat 330 d l excavator (prefix thj) service repair manual (thj0000...
jfdjskmdmme
 
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...
jfdjskmdmme
 
Caterpillar cat 330 d l excavator (prefix nbd) service repair manual (nbd0000...
jfdjskmdmme
 
Caterpillar cat 330 d l excavator (prefix mwp) service repair manual (mwp0000...
jfdjskmdmme
 
Caterpillar cat 330 d l excavator (prefix mey) service repair manual (mey0000...
jfdjskmdmme
 
Ad

Recently uploaded (20)

PDF
CASE CX55B Mini Excavator Service Repair Manual Instant Download.pdf
zhongxiaqielan90
 
PPTX
Air craft and Rescue related ppt which detailed explain about
akhilsbr
 
PDF
Designyze – Creative Digital Marketing & Design Agency in India
designyze099
 
PPTX
Found naturally in fruits, vegetables, n
ABHIJEETRAJ53
 
PDF
Bobcat t40180 telescopic handler repair manual sn b33 j11001 and above.pdf
Service Repair Manual
 
PPTX
ENERGY RESOUCES_Class 10_Geo_2020-21.pptx
MananMishra15
 
PDF
John Deere 5055e Fuel System Repair Manual - Tm900319.pdf
Service Repair Manual
 
PPT
industrialsafetyhazards-180118095222.ppt
gmoudgil1
 
PDF
Volvo EC160B LC EC160BLC Excavator Service Repair Manual Instant Download.pdf
Service Repair Manual
 
PPT
157_37315_EA221_2013_1__2_1_Chapter 1, introduction to OR.ppt
SIRINET2
 
PDF
BOBCAT 442 Excavator Service Repair Manual.pdf
Service Repair Manual
 
PPTX
DNA Packaging_ Structure and Function in Cells.pptx
AbhijithA57
 
PDF
Why Has Vertical Farming Recently Become More Economical.pdf.pdf
Skyfield Agritech
 
PDF
Volvo Dump Truck A40E Service Repair Manual.pdf
Nombre Apellidos
 
PDF
Some briefly information About buying linkedin accounts.pdf
trampdonal260
 
PDF
Deep Learning and AI Tools for Monitoring and Detecting Diseases in Freshwate...
PriyankaKilaniya
 
PDF
CASE CX45B Series 2 Mini Excavator Service Repair Manual Instant Download.pdf
zhongxiaqielan90
 
DOC
Bài tập bổ trợ I-learn Smart World 9 HK1 Unit 4 (HS) (1).doc
XunHuyn12
 
PDF
CASE CX50B Series 2 Mini Excavator Service Repair Manual Instant Download.pdf
zhongxiaqielan90
 
PDF
John Deere 370E 410E, 460E Articulated Dump Trucks Diagnostic Operator’s Manu...
Service Repair Manual
 
CASE CX55B Mini Excavator Service Repair Manual Instant Download.pdf
zhongxiaqielan90
 
Air craft and Rescue related ppt which detailed explain about
akhilsbr
 
Designyze – Creative Digital Marketing & Design Agency in India
designyze099
 
Found naturally in fruits, vegetables, n
ABHIJEETRAJ53
 
Bobcat t40180 telescopic handler repair manual sn b33 j11001 and above.pdf
Service Repair Manual
 
ENERGY RESOUCES_Class 10_Geo_2020-21.pptx
MananMishra15
 
John Deere 5055e Fuel System Repair Manual - Tm900319.pdf
Service Repair Manual
 
industrialsafetyhazards-180118095222.ppt
gmoudgil1
 
Volvo EC160B LC EC160BLC Excavator Service Repair Manual Instant Download.pdf
Service Repair Manual
 
157_37315_EA221_2013_1__2_1_Chapter 1, introduction to OR.ppt
SIRINET2
 
BOBCAT 442 Excavator Service Repair Manual.pdf
Service Repair Manual
 
DNA Packaging_ Structure and Function in Cells.pptx
AbhijithA57
 
Why Has Vertical Farming Recently Become More Economical.pdf.pdf
Skyfield Agritech
 
Volvo Dump Truck A40E Service Repair Manual.pdf
Nombre Apellidos
 
Some briefly information About buying linkedin accounts.pdf
trampdonal260
 
Deep Learning and AI Tools for Monitoring and Detecting Diseases in Freshwate...
PriyankaKilaniya
 
CASE CX45B Series 2 Mini Excavator Service Repair Manual Instant Download.pdf
zhongxiaqielan90
 
Bài tập bổ trợ I-learn Smart World 9 HK1 Unit 4 (HS) (1).doc
XunHuyn12
 
CASE CX50B Series 2 Mini Excavator Service Repair Manual Instant Download.pdf
zhongxiaqielan90
 
John Deere 370E 410E, 460E Articulated Dump Trucks Diagnostic Operator’s Manu...
Service Repair Manual
 
Ad

Caterpillar cat 330 d l excavator (prefix ern) service repair manual (ern00001 and up)

  • 1. Service Repair Manual Models 330D and 330D L Excavator
  • 2. Disassembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 1P-2420 Transmission Repair Stand 1 B 138-7573 Link Bracket 2 C 1P-1863 Retaining Ring Pliers 1 D 208-6033 Spanner Socket 1 E 138-7574 Link Bracket 2 F 5F-7366 Forcing Screw 1 1P-5546 Crossblock 1 1U-9889 Crossblock 1 1P-0520 Driver Group 1 6V-7888 Puller Leg 2 1H-3112 Puller Assembly 1 1P-5551 Adjustable Screw Assembly 1 G 1U-7600 Slide Hammer Puller Gp 1 8T-0266 Bolt 1 Start By: A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove". Note: Cleanliness is an important factor. Before the disassembly procedure, the thoroughly clean the exterior of the component. This will prevent dirt from entering the internal mechanism. Note: Some of the images that are in this procedure do not show the sprocket assembly that is attached to the final drive housing. If necessary, the weights that are given include the weight of the sprocket assembly. 1. Put an alignment mark across the sections of the final drive for assembly purposes. The parts must be reinstalled in the part's original locations. 2/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 3. Illustration 1 g00708089 2. Fasten the final drive to Tooling (A) , as shown. The weight of the final drive assembly is approximately 312 kg (688 lb). 3. Remove bolts (1) and the washers that hold the cover in position. Illustration 2 g00708090 4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to cover (2) , as shown. Remove the cover. The weight of the cover is approximately 32 kg (70 lb). 3/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 4. Illustration 3 g00879362 5. Remove bolts (3) . Remove gear (5) . Check plate (6) . Replace plate (6) if wear is shown. Remove plugs (4) from cover (2) . Illustration 4 g00879365 6. Remove O-ring seal (7) from plugs (4) . Illustration 5 g00780428 4/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 5. 7. Remove gear (8) . Remove spacer (9) . Illustration 6 g00780432 8. Remove retaining ring (10) with Tooling (C) . Remove washer (11) . Remove gear (12) . Remove bearing assembly (13) . Remove second washer (11) . 9. Repeat Step 8 for the remaining two gear assemblies. Illustration 7 g00781401 10. Remove retaining ring (14) . 5/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 6. Illustration 8 g00781407 11. Remove carrier assembly (15) . Illustration 9 g01389593 12. Use a suitable press in order to remove the shafts from carrier assembly (15) . 6/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 7. Illustration 10 g00781412 13. Remove gear (16) . Remove spacer (17) . Illustration 11 g00781466 14. Remove retaining ring (18) . 15. Remove carrier assembly (19) . Illustration 12 g00879368 7/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 8. 16. Disassemble carrier assembly (19) , as follows. a. Drive spring pin (20) into planetary shaft (21) with a hammer and a punch. Illustration 13 g00781476 b. Remove planetary shaft (21) . c. Remove spring pin (20) from planetary shaft (21) with a hammer and a punch. Illustration 14 g00781516 d. Remove thrust washers (22) and planetary gear (24) from the carrier assembly. e. Remove bearing (23) from planetary gear (24) . 17. Repeat Steps 16.a through 16.e for the other two planetary. 8/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 9. Illustration 15 g00781529 18. Remove gear (25) . Remove spacer (26) . Illustration 16 g00781559 19. Remove carrier assembly (27) . 20. Use two people to remove carrier assembly (27) . The weight of the carrier assembly is approximately 38 kg (85 lb). 21. Disassemble carrier assembly (27) , as follows. 9/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 10. Illustration 17 g00781719 a. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch. Illustration 18 g00781601 b. Remove planetary shaft (28) . c. Remove spring pin (29) from planetary shaft (28) with a hammer and a punch. Illustration 19 g00781607 d. Remove thrust washers (30) and planetary gear (32) from the carrier assembly. e. Remove two bearings (31) from the planetary gear. 22. Repeat Steps 21.a through 21.e for the other two planetary gears. 10/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 11. Illustration 20 g00781730 23. Use two people to remove gear (33) . The weight of gear is approximately 41 kg (90 lb). Illustration 21 g00781807 24. Remove O-ring seal (34) . Illustration 22 g01147650 25. Remove bolts (35A) and plates (35B) . 11/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 12. Illustration 23 g01147651 26. Use Tooling (G) to remove dowel (37) from stopper plate (35) . Illustration 24 g01147759 27. Secure Tooling (D) to stopper plate (35) . Use Tooling (D) to remove stopper plate (35) . 12/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 13. Illustration 25 g01147930 28. Use Tooling (E) and a suitable lifting device to remove housing (36) . The weight of housing (36) is approximately 100 kg (220 lb). Illustration 26 g01147951 29. Remove Duo-Cone seal (39A) from housing (38) . Illustration 27 g01147975 13/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 14. Illustration 28 g01147934 30. Remove Duo-Cone seal (39B) from housing (36) . 31. Use Tooling (F) in order to remove bearings (40) and (41) from housing (36) . 32. If necessary, remove the final drive sprocket from the sprocket housing. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install". Copyright 1993 - 2020 Caterpillar Inc. All Rights Reserved. Private Network For SIS Licensees. Mon Aug 17 14:05:20 UTC+0800 2020 14/14(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 15. Shutdown SIS Previous Screen Product: EXCAVATOR Model: 330D L EXCAVATOR ERN Configuration: 330D Excavator ERN00001-UP (MACHINE) POWERED BY C-9 Engine Disassembly and Assembly 330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit Machine Systems Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018 i06252413 Final Drive - Disassemble - Type-Two SMCS - 4050-015 S/N - B6H568-UP S/N - DTS1-UP S/N - EAH1-UP S/N - EDX1-UP S/N - EFT1-UP S/N - ERN275-UP S/N - FAR1-UP S/N - FFK1-UP S/N - GGE1-UP S/N - GGH1-UP S/N - HHK1-UP S/N - J2F1-UP S/N - JBT1-UP S/N - JLP299-UP S/N - JTN1-UP S/N - JWR1-UP 1/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 16. S/N - KDJ1-UP S/N - LMG1-UP S/N - LRM1-UP S/N - M3M1-UP S/N - M3N1-UP S/N - M4T1-UP S/N - MDS1-UP S/N - MEY179-UP S/N - MPL1-UP S/N - MWP1-UP S/N - MYG1-UP S/N - MYP1-UP S/N - NBD169-UP S/N - NBN1-UP S/N - PGW1-UP S/N - PPN1-UP S/N - PRF1-UP S/N - PTB1-UP S/N - RAS573-UP S/N - T2Y226-UP S/N - THJ1-UP S/N - TLY1-UP S/N - W3K1-UP S/N - WDC1-UP S/N - WET1-UP S/N - WRK1-UP 2/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 17. S/N - XBH1-UP S/N - YCF1-UP S/N - ZCT1-UP S/N - ZML1-UP Disassembly Procedure Table 1 Required Tools Tool Part Number Part Description QTY A 439-3940 Link Brackets 3 B 439-3939 Link Bracket 2 C 154-6183 Forcing Bolts 3 Start By: A. Remove the final drive and the travel motor. 1. Put an alignment mark across the sections of the final drive for assembly purposes. The parts must be reinstalled in the original locations. Illustration 1 g02151790 Note: The weight of the entire final drive assembly is approximately 550 kg (1200 lb). 2. Attach Tooling (A) and a suitable lifting device to cover (2) . The weight of cover (2) is approximately 32 kg (70 lb). Remove bolts (1) and cover (2) . 3/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 18. Illustration 2 g00879362 3. Remove bolts (3) . Remove gear (5) . Remove plate (6) . Remove plugs (4) from cover (2) . Illustration 3 g00879365 4. Remove O-ring seal (7) from plugs (4) . 4/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 19. Illustration 4 g02151806 5. Remove sun gear (8) , spacer (9) , and planetary gear assembly (10) . Illustration 5 g02151809 6. Remove retaining ring (11) , washer (12) , planetary gear (13) , roller bearing (15) , and washer (16) from carrier assembly (17) . 7. Repeat Step 6 for the remaining two gear assemblies. 8. Remove retaining ring (14) and sun gear (18) from carrier assembly (17) . 5/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 20. Illustration 6 g02152150 9. Use a suitable press to remove the shafts from carrier assembly (17) . Illustration 7 g02151813 10. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (19) . The weight of planetary gear assembly (19) is approximately 48 kg (105 lb). Remove planetary gear assembly (19) . 11. Remove spacer (20) . 6/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 21. Illustration 8 g02151782 12. Drive spring pin (21) into planetary shaft (22) with a suitable hammer and a suitable punch. 13. Remove planetary shaft (22) , washer (24) , roller bearing (25) , planetary gear (26) , and washer (27) from the planetary gear assembly (19) . 14. Remove spring pin (21) from planetary shaft (22) with a suitable hammer and a suitable punch. 15. Remove retaining ring (23) and sun gear (28) from planetary gear assembly (19) . Illustration 9 g02152208 7/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 22. 16. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (29) . The weight of planetary gear assembly (29) is approximately 38 kg (85 lb). Remove planetary gear assembly (29) . Illustration 10 g02152467 17. Drive spring pin (30) into planetary shaft (31) with a suitable hammer and a suitable punch. 18. Remove planetary shaft (31) , washer (32) , roller bearings (33) , planetary gear (34) , and washer (35) from the planetary gear assembly (29) . 19. Remove spring pin (30) from planetary shaft (31) with a suitable hammer and a suitable punch. 8/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 23. Illustration 11 g02152399 20. Attach Tooling (A) and a suitable lifting device to ring gear (36) . The weight of ring gear (36) is approximately 66 kg (146 lb). Remove ring gear (36) . 21. Remove O-ring seal (37) from sprocket housing (38) . Illustration 12 g02152525 Illustration 13 g02152528 Note: Mark the orientation of coupling gear (40) for assembly purposes. 22. Remove bolts (39) from coupling gear (40) . Use Tooling (C) in order to remove coupling gear (40) from the motor housing. 9/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 24. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
  • 25. Illustration 14 g02152546 23. Remove shims (41) from the motor housing. Illustration 15 g02152552 Note: Upper bearing cone (42) and lower bearing cone (43) are a slip fit on the motor housing. While you remove sprocket housing (38) from the motor housing, upper bearing cone (42) may stay with the sprocket housing, or upper bearing cone (42) may stay on the motor housing. 24. Attach Tooling (B) and a suitable lifting device to sprocket housing (38) . The weight of sprocket housing (38) is approximately 109 kg (240 lb). Remove sprocket housing (38) and upper bearing cone (42) . 10/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
  • 26. Illustration 16 g02152595 25. Remove dowels (45) from the motor housing. 26. Remove Duo-Cone seal (44) from the motor housing. 27. If lower bearing cone (43) remained on the motor housing, then remove the lower bearing cone. Illustration 17 g02152598 28. Remove Duo-Cone seal (46) from the sprocket housing. 29. If upper bearing cone (42) remained on the sprocket housing, then remove the upper bearing cone. 30. Remove the bearing cups from the sprocket housing. (Type 1) Disassembly Procedure Table 2 Required Tools Tool Part Number Part Description Qty 11/19(W) w 2020/8/17 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...