Caterpillar cat 330 d mh excavator (prefix c5k) service repair manual (c5k00001 and up)

Service Repair Manual
Models
330D MH EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D MH EXCAVATOR C5K
Configuration: 330D Material Handler (HCR & FCR) C5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D Excavator Machine Systems
Media Number -KENR5993-02 Publication Date -01/02/2017 Date Updated -20/02/2017
i02770233
Final Drive - Disassemble
SMCS - 4050-015
S/N - C5K1-222
S/N - LEM1-187
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 194-3878 Spanner Socket 1
E 138-7574 Link Bracket 2
F
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
1/12(W)
w
2020/7/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

G
1U-7600 Slide Hammer Puller Gp 1
8T-0266 Bolt 1
Start By:
a. Remove the final drive and the travel motor. Refer to Disassembly and Assembly, "Final
Drive and Travel Motor - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
Note: Some of the images that are in this procedure do not show the sprocket assembly that
is attached to the final drive housing. If necessary, the weights that are given include the
weight of the sprocket assembly.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled to the original locations.
Illustration 1 g00708089
2/12(W)
w
2020/7/27

2. Fasten the final drive to Tooling (A). The weight of the final drive assembly is
approximately 544 kg (1200 lb).
3. Remove bolts (1) that hold the cover in position.
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2). Remove the cover. The weight of the cover is approximately 32 kg (70 lb).
5. Remove bolts (3). Remove gear (5). Check plate (6). Replace plate (6) if wear is shown.
Remove plugs (4) from cover (2).
3/12(W)
w
2020/7/27

6. Remove O-ring seal (7) from plugs (4).
7. Remove gear (8). Remove spacer (9).
8. Use Tooling (C) to remove retaining ring (10). Remove washer (11). Remove gear (12).
Remove bearing assembly (13). Remove second washer (11).
9. Repeat Step 8 for the remaining two gear assemblies.
4/12(W)
w
2020/7/27

10. Remove retaining ring (14).
11. Remove carrier assembly (15).
12. Use a suitable press to remove the shafts from carrier assembly (15).
5/12(W)
w
2020/7/27

14. Remove retaining ring (18).
16. Disassemble carrier assembly (19), as follows.
a. Drive spring pin (20) into planetary shaft (21) with a hammer and a punch.
6/12(W)
w
2020/7/27

b. Remove planetary shaft (21).
c. Remove spring pin (20) from planetary shaft (21) with a hammer and a punch.
d. Remove thrust washers (22) and planetary gear (24) from the carrier assembly.
e. Remove bearing (23) from planetary gear (24).
17. Repeat Steps 16.a through 16.e for the other two planetary.
7/12(W)
w
2020/7/27

20. Use two people to remove carrier assembly (27). The weight of the carrier assembly is
21. Disassemble carrier assembly (27), as follows.
a. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch.
8/12(W)
w
2020/7/27

b. Remove planetary shaft (28).
c. Remove spring pin (29) from planetary shaft (28) with a hammer and a punch.
d. Remove thrust washers (30) and planetary gear (32) from the carrier assembly.
e. Remove two bearings (31) from the planetary gear.
22. Repeat Steps 21.a through 21.e for the other two planetary gears.
9/12(W)
w
2020/7/27

23. Use two people to remove gear (33). The weight of gear is approximately 41 kg (90 lb).
24. Remove O-ring seal (34).
25. Remove bolts (35A) and plates (35B).
26. Use Tooling (G) to remove dowel (37) from stopper plate assembly (35).
10/12(W)
w
2020/7/27

27. Secure Tooling (D) to stopper plate assembly (35). Use Tooling (D) to remove stopper plate
assembly (35).
28. Use Tooling (E) and a suitable lifting device to remove housing (36). The weight of housing
(36) is approximately 100 kg (220 lb).
29. Remove Duo-Cone seal (39A) from housing (38).
11/12(W)
w
2020/7/27

30. Remove Duo-Cone seal (39B) from housing (36).
31. Use Tooling (F) in order to remove bearings (40) and (41) from housing (36).
32. If necessary, remove the final drive sprocket from the sprocket housing. Refer to
Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 27 13:51:52 UTC+0800 2020
12/12(W)
w
2020/7/27

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D MH EXCAVATOR C5K
Configuration: 330D Material Handler (HCR & FCR) C5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D Excavator Machine Systems
Media Number -KENR5993-02 Publication Date -01/02/2017 Date Updated -20/02/2017
i05331848
Final Drive - Disassemble
SMCS - 4050-015
S/N - C5K223-UP
S/N - LEM188-UP
S/N - PEL1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 138-7576 Link Bracket 2
H 154-6183 Forcing Bolts 3
Start By:
A. Start by removing the final drive and the travel motor. Refer to Disassembly and Assembly,
"Final Drive and Travel Motor - Remove".
1/13(W)
w
2020/7/27

Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled to the original locations.
2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto
Tooling (A) . The weight of the final drive assembly is approximately 550 kg (1200 lb).
3. Remove bolts (1) .
4. Use Tooling (B) and a suitable lifting device to remove cover (2) . The weight of cover (2)
is approximately 32 kg (70 lb).
2/13(W)
w
2020/7/27

5. Remove bolts (3) and gear (4) . Check plate (6) . Replace plate (6) if plate (6) is worn.
Remove plugs (5) from cover (2) .
6. Remove O-ring seals (7) from plugs (5) .
3/13(W)
w
2020/7/27

7. Remove gear (8) and spacer (9) .
8. Use Tooling (C) to remove retaining ring (10) . Remove washer (11) and gear (12) .
Remove bearing assembly (13) and washer (14) .
9. Repeat Step 8 for the other two gear assemblies.
10. Remove retaining ring (15) .
4/13(W)
w
2020/7/27

11. Remove carrier assembly (16) .
12. Use a suitable press to remove the shafts from carrier assembly (16) .
5/13(W)
w
2020/7/27

13. Remove gear (17) and spacer (18) .
14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19) . The weight
of planetary carrier (19) is approximately 48 kg (105 lb).
6/13(W)
w
2020/7/27

15. Remove retainer ring (21) . Lift planetary carrier (19) off sun gear (20) .
16. Drive spring pin (23) into planetary shaft (22) .
17. Remove planetary shaft (22) . Use a suitable punch to remove spring pin (23) from
planetary shaft (22) .
7/13(W)
w
2020/7/27

18. Remove washers (24) and bearing (25) from planetary gear (26) .
19. Repeat Steps 16 through 18 for the other two planetary gears.
20. Remove spacer (27) .
21. Use two people to remove carrier assembly (28) . The weight of carrier assembly (28) is
8/13(W)
w
2020/7/27

22. Drive spring pin (30) into shaft (29) .
23. Remove shaft (29) . Use a suitable punch to remove spring pin (30) from shaft (29) .
24. Remove washers (31) and bearings (32) from planetary gear (33) .
9/13(W)
w
2020/7/27

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

25. Repeat Steps 22 through 24 for the other three planetary gears.
26. Fasten Tooling (E) and a suitable lifting device to ring gear (34) , as shown. Remove ring
gear (34) from sprocket housing (35) . The weight of ring gear (34) is approximately 66 kg
(146 lb).
27. Remove O-ring seal (36) from sprocket housing (35) .
10/13(W)
w
2020/7/27

28. Remove bolts (37) from coupling gear (38) .
Note: Mark the orientation of coupling gear (38) for assembly purposes.
29. Install Tooling (H) in coupling gear (38) . Tighten Tooling (H) evenly in order to loosen
coupling gear (38) . Remove the coupling gear from the motor housing.
11/13(W)
w
2020/7/27

30. Remove shims (40) from the motor housing.
Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.
31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35) . Separate the
sprocket housing from the motor housing. The weight of sprocket housing (35) is 109 kg
(240 lb).
32. Remove the locating pins from the motor housing.
33. Remove Duo-Cone seal (41) from the motor housing.
34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
12/13(W)
w
2020/7/27

Caterpillar cat 330 d mh excavator (prefix c5k) service repair manual (c5k00001 and up)

More Related Content

More from fjjskedmme (20)

Recently uploaded (20)

Caterpillar cat 330 d mh excavator (prefix c5k) service repair manual (c5k00001 and up)