Caterpillar cat 336 f l xe excavator (prefix ltp) service repair manual (ltp00001 and up)

Service Repair Manual
Models
336F L XE
336F LN XE Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L XE EXCAVATOR LTP
Configuration: 336F L XE & 336F LN XE Excavators LTP00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR6140-04 Publication Date -01/04/2015 Date Updated -21/02/2018
i03863290
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 by 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
1/10
336F L XE & 336F LN XE Excavators LTP00001-UP (MACHINE) POWERED BY ...
2020/6/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
2020/6/22

5. Remove O-ring seal (3), port plate (4), and bearing (5).
6. Remove O-ring seals (6). Remove springs (7).
This is an example of the use of Tooling (B).
3/10
2020/6/22

7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
10. Remove plates (13) and friction discs (14).
4/10
2020/6/22

11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
5/10
2020/6/22

14. Use Tooling (D) in order to remove retaining ring (17) from shaft (15).
15. Use a suitable press in order to remove bearing race (18) from shaft (15).
16. Rotate shaft (15). Use a suitable press and tooling (E) in order to remove bearing race (19)
from shaft (15).
17. Remove cam plate (20) from barrel assembly (21).
6/10
2020/6/22

18. Remove piston assemblies and retainer plate (22) from barrel assembly (21).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
19. Remove ball (23) and springs (24).
7/10
2020/6/22

20. Remove bearing (25).
21. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
22. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27).
23. Remove lip seal (28).
24. Remove bolts (29) and cover (30).
8/10
2020/6/22

25. Remove seal (31) and backup ring (32).
26. Remove piston actuator (33) and seal (34).
27. Remove O-ring seal (35) from the housing of the travel motor.
9/10
2020/6/22

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07195340
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
6V-5215 M8 X 1.25 X 16 MM Bolt 2
9M-1974 M8 Hard Washer 2
D 1P-0510 Driver Gp 1
Start By:
a. Remove travel motor.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/14
2020/6/22

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Fasten travel motor (1) in a vertical position on Tooling (A). The weight of travel motor (1)
is approximately 82 kg (180 lb).
2. Remove bolts (2) and cap (3).
2/14
2020/6/22

3. Remove bolts (4) and cap (5).
4. Remove spring (6), spring (9), spool assembly (8), and spring seats (7).
3/14
2020/6/22

5. Remove plug (11), relief valve (10), and the O-ring seals.
6. Remove plug (13), relief valve (12), and the O-ring seals.
7. Remove plug (14), and the O-ring seal.
4/14
2020/6/22

8. Remove plug (15), spool assembly (16), spring (17), and the O-ring seals.
5/14
2020/6/22

9. Remove plugs (18) and the O-ring seals.
10. Remove bolts (19).
11. Attach Tooling (B) and a suitable lifting device to motor head assembly (20). The weight of
motor head assembly (20) is approximately 27 kg (60 lb). Remove motor head assembly
(20).
6/14
2020/6/22

12. Remove the ball bearing that is located on the bottom side of motor head assembly (20).
Port plate (25) may still be adhered to the bottom of motor head assembly (20).
13. Remove O-ring seals (21), O-ring seal (22), springs (23), springs (24), and port plate (25).
Note: Note the location of springs (23). They must be installed in the same location during
the assembly procedure.
7/14
2020/6/22

14. Insert Tooling (C) into piston assembly (26). Use a suitable prying device and Tooling (C)
to remove piston assembly (26).
15. Remove O-ring seal (27) and O-ring seal (28).
16. Use suitable prying devices to remove guide assembly (29).
17. Remove O-ring seal (30).
8/14
2020/6/22

18. Remove separator plates (31) and friction plates (32). Note the alternating order of separator
plates (31) and friction plates (32) for assembly purposes.
19. Remove barrel assembly (33).
Note: Do not allow the components of barrel assembly (33) to come apart while you
remove barrel assembly (33). The components of barrel assembly (33) must be reinstalled
into the original positions.
9/14
2020/6/22

Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
20. Remove piston assemblies (34) and retainer (35).
21. Remove hold down ball (36).
10/14
336F L XE & 336F LN XE Excavators LTP00001-UP (MACHINE) POWERED B...
2020/6/22

22. Remove dowel pins (37).
23. Put location marks on swashplate (38) for assembly purposes. Remove swashplate (38).
24. Remove pistons (39) and the balls.
25. Remove springs (40).
11/14
2020/6/22

26. Use a suitable press and Tooling (D) to remove snap ring (41), spacers (42), and spring (43).
12/14
2020/6/22

27. Use a soft faced hammer to remove shaft assembly (44). Remove shaft assembly (44) in the
direction that is indicated by the arrow.
28. Remove O-ring seal (45).
29. Remove lip seal (46).
30. Use a suitable press to push shaft (47) out of bearing (48).
13/14
2020/6/22

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
A
1U-7506 Adapter 1
8T-4244 Nut 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
2020/6/22

1. Install O-ring seal (35) onto the housing of the travel motor.
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
3. Install backup ring (32) and seal (31).
2/10
2020/6/22

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
7. Rotate the housing.
3/10
2020/6/22

8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
2020/6/22

Caterpillar cat 336 f l xe excavator (prefix ltp) service repair manual (ltp00001 and up)

More Related Content

Similar to Caterpillar cat 336 f l xe excavator (prefix ltp) service repair manual (ltp00001 and up) (17)

More from fjkskedmme (20)

Recently uploaded (20)

Caterpillar cat 336 f l xe excavator (prefix ltp) service repair manual (ltp00001 and up)