Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
336D L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR LMG
Configuration: 336D L Excavator LMG00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07188136
Final Drive and Travel Motor - Install
SMCS - 4050-012; 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
5P-0306 Vacuum Transducer 1
FT-1115 Vacuum Cap 1
6V-4142 Fitting 1
5K-5068 Fitting 1
B 1U-9200 Lever Puller Hoist 1
C 439-3938 Link Bracket 1
D - Loctite C5A Copper Anti-Seize -
Note: Check the O-ring seals for wear or for damage. Replace the O-ring seals, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
336D L Excavator LMG00001-UP (MACHINE) POWERED BY C9 Engine(SEBP56...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01181921
1. Attach Tooling (C) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 73 kg (160 lb).
2. Position travel motor (11). Install bolts (12) that mount travel motor (11) to final drive (13).
2/5
2020/5/13

3. Install O-ring seals (10) and (9).
4. Install counterbalance valve (8) and bolts (7).
3/5
2020/5/13

5. Attach Tooling (B) and a suitable lifting device to final drive and travel motor (5). The
weight of final drive and travel motor (5) is approximately 860 kg (1896 lb).
6. Carefully position final drive and travel motor (5). Apply Tooling (D) to the threads of bolts
(6).
7. Tighten bolts (6) in an alternating sequence to a torque of 250 ± 25 N·m (184 ± 18 lb ft).
Turn an additional angle of 45 ± 5 degrees. Refer to Service Magazine , M0083843 , "An
Improved Bolt Tightening Procedure for the Critical Joints Is Now Used on all Excavators"
for more detailed information.
8. Install fitting (4). Connect hose assemblies (3).
4/5
2020/5/13

9. Remove Tooling (A). Install the cap onto the hydraulic tank.
10. Fill the hydraulic system. Refer to Operation and Maintenance Manual, "Hydraulic System
Oil Level - Check". Refer to Operation and Maintenance Manual, "Lubricant Viscosities
and Refill Capacities".
11. Install cover (2) and bolts (1). Tighten bolts (1) to a torque of 130 ± 10 N·m (96 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 10:46:56 UTC+0800 2020
5/5
2020/5/13

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02434256
Swivel - Remove
SMCS - 5060-011
Removal Procedure
Table 1
Required Tools
A FT-2674 Vacuum Cap 1
B 138-7573 Link Bracket 2
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
NOTICE
containing fluids.
Cat products.
1/3
2020/5/13

1. Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach
an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This
procedure will pull vacuum on the hydraulic system.
2. Disconnect hose assemblies (1), (2), and (3). Remove support (4).
2/3
2020/5/13

3. Attach Tooling (B) and a suitable lifting device to swivel (9). The weight of swivel (9) is
approximately 45 kg (95 lb). Remove bolts (6) and retainer (8). Remove clamp (7) and boot
(5).
4. Remove bolts (10) and covers (11).
5. Disconnect hose assemblies (15). Disconnect fitting (16). Disconnect hose assemblies (12).
Remove fittings (14). Remove bolts (13). Remove swivel (9).
Wed May 13 10:47:52 UTC+0800 2020
3/3
2020/5/13

Shutdown SIS
Previous Screen
Product: EXCAVATOR
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
i02568407
Swivel - Disassemble
SMCS - 5060-015
Disassembly Procedure
Table 1
Required Tools
A
6V-3822 Bolt 2
6V-5839 Washer 2
1P-5546 Crossblock 1
5P-4168 Step Plate 1
5F-7366 Screw 1
B 1P-2420 Transmission Repair Stand 1
Start By:
a. Remove the swivel joint. Refer to Disassembly and Assembly, "Swivel - Remove".
NOTICE
containing fluids.
Cat products.
1/3
2020/5/13

1. Thoroughly clean the outside of the swivel joint prior to disassembly.
2. Use a suitable lifting device to position the swivel joint onto Tooling (B). Fasten the swivel joint to
Tooling (B), as shown. The weight of the swivel joint is approximately 43 kg (95 lb).
3. Remove bolts (1), washers (2), and cover (3) from outside housing (8).
4. Remove O-ring seal (7) from outside housing (8).
5. Remove bolts (4), washers (5), and retainer (6) from rotor (11).
2/3
2020/5/13

6. Use Tooling (A) in order to separate the outside housing (8) from rotor (11). The weight of outside
housing (8) is approximately 20 kg (45 lb). The weight of rotor (11) is approximately 21 kg (46 lb).
7. Remove seals (9) from outside housing (8).
8. Remove O-ring seals (10) from the outside housing (8).
9. Remove plug (13). Remove O-ring seal (12) from plug (13).
Wed May 13 10:48:48 UTC+0800 2020
3/3
2020/5/13

Shutdown SIS
Previous Screen
Product: EXCAVATOR
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power
Unit Machine Systems
i02426337
Swivel - Assemble
SMCS - 5060-016
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components,
if necessary.
1/2
2020/5/13

1. Install O-ring seal (12) on plug (13). Apply clean hydraulic oil on the seal. Install plug (13).
2. Install seals (9) and O-ring seals (10) into outside housing (8).
3. Carefully install outside housing (8) over rotor (11).
4. Install retainer (6), washers (5), and bolts (4). This holds the rotor (11) and the outside housing (8)
together.
5. Apply clean hydraulic oil on O-ring seal (7). Install the O-ring seal in the outside housing.
6. Install cover (3), washers (2), and bolts (1) that secure the cover.
7. Check the swivel joint for leaks. Plug the drain ports of the inside body. Apply shop air pressure in
the top of the swivel joint and check the swivel joint for leaks. The shop air pressure should be
between 0.2758 MPa (40 psi) and 0.4137 MPa (60 psi).
End By:
a. Install the swivel joint. Refer to Disassembly and Assembly, "Swivel - Install".
Wed May 13 10:49:44 UTC+0800 2020
2/2
2020/5/13

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02434356
Swivel - Install
SMCS - 5060-012
Table 1
Required Tools
B 138-7573 Link Bracket 2
1. Attach Tooling (B) and a suitable lifting device to swivel (9). The weight of swivel (9) is
approximately 45 kg (95 lb). Position swivel (9). Install boot (5) and clamp (7). Install
retainer (8) and bolts (6).
1/3
2020/5/13

2. Connect hose assemblies (1), (2), and (3). Install support (4).
3. Install bolts (13). Install fittings (14). Install fitting (16). Connect hose assemblies (15).
Connect hose assemblies (14) and (12) to swivel (9).
4. Install covers (11) and bolts (10).
2/3
2020/5/13

5. Remove Tooling (A).
Wed May 13 10:50:40 UTC+0800 2020
3/3
2020/5/13

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02434311
Solenoid Valve (Two-Way Flow and One Pump/Two Pump) -
Remove
SMCS - 5479-011
Removal Procedure
Table 1
Required Tools
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: Put identification marks on all lines, on all hoses, on all harness assemblies, and on all tubes
for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
NOTICE
containing fluids.
Cat products.
1/3
2020/5/13

Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A).
Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the
hydraulic system.
2/3
2020/5/13

2. Open door (1).
3. Disconnect harness assemblies (4).
4. Disconnect hose assemblies (2) and (3).
5. Remove bolts (5) and solenoid valve (6).
Wed May 13 10:51:35 UTC+0800 2020
3/3
2020/5/13

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02434312
Solenoid Valve (Two-Way Flow and One Pump/Two Pump) -
Install
SMCS - 5479-012
Table 1
Required Tools
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/2
2020/5/13

1. Install solenoid valve (6) and bolts (5).
2. Connect hose assemblies (2) and (3).
3. Connect harness assemblies (4).
4. Close door (1).
5. Remove Tooling (A) from the hydraulic tank.
Wed May 13 10:52:31 UTC+0800 2020
2/2
2020/5/13

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02413351
Swing Cushion Valve - Remove
SMCS - 5454-015
Removal Procedure
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release".
1. Disconnect hose assemblies (1) and (2). Disconnect harness assembly (4). Remove bolts (3)
and remove swing cushion valve (5).
Wed May 13 10:53:27 UTC+0800 2020
1/1
2020/5/13

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02096925
Swing Cushion Valve - Disassemble - Fine Swing Solenoid
SMCS - 5454-015
Disassembly Procedure
Start By:
a. Remove the swing cushion valve. Refer to Disassembly and Assembly, "Swing Cushion
Valve - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will prevent dirt from entering the internal
mechanism.
1. Remove O-ring seals (1) and (2) from the valve body.
2. Remove the fine swing solenoid, as follows.
1/4
2020/5/13

a. Remove bolts (3).
b. Remove fine swing solenoid (4).
c. Remove O-ring seal (8), (6), (7), and (5).
3. Remove the relief valves, as follows.
2/4
2020/5/13

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
a. Remove relief valve (9) from the valve body.
b. Remove spring (12), plunger (11), and ball valve (10) from relief valve (9).
c. Remove backup ring (13) and O-ring seal (14) from the relief valve.
4. Repeat Steps 3.a through 3.c for the remaining relief valve.
Wed May 13 10:54:23 UTC+0800 2020
3/4
2020/5/13

Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant Download.pdf

More Related Content

Similar to Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant Download.pdf (19)

More from zan2736ban (20)

Recently uploaded (20)

Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant Download.pdf