Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
336D L Excavator

Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
4/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

6. Remove O-ring seal (3) , port plate (4) , and bearing (5) .
7. Remove O-ring seals (6) . Remove springs (7) .
5/13
2020/5/21

This is an example of the use of Tooling (B) .
8. Place a shop towel over brake piston (8) . Retain brake piston (8) with Tooling (B) . Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y) . Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
6/13
2020/5/21

11. Remove plates (13) and friction discs (14) .
12. Install Tooling (C) into shaft (15) . Use a prybar to remove the rotating assembly (16) from
the housing.
7/13
2020/5/21

13. Remove Tooling (C) from shaft (15) .
14. Remove shaft (15) from rotating assembly (16) .
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
8/13
2020/5/21

16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
17. Rotate shaft (15) . Install shaft (15) into a suitable press. Install Tooling (E) . Remove
bearing race (19) from shaft (15) .
18. Remove cam plate (20) from barrel assembly (21) .
9/13
2020/5/21

19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
20. Remove ball (23) and springs (24) .
10/13
2020/5/21

21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
25. Remove bolts (29) and cover (30) .
11/13
2020/5/21

26. Remove seal (31) and backup ring (32) .
27. Remove piston actuator (33) and seal (34) .
28. Remove O-ring seal (35) from the housing of the travel motor.
12/13
2020/5/21

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR W3K
Configuration: 336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i03124523
Travel Motor - Assemble
SMCS - 4351-016
S/N - B6H1-UP
S/N - DTS1-UP
S/N - EAH1-UP
S/N - EDX1-UP
S/N - EFT1-UP
S/N - ERN1-UP
S/N - FAR1-UP
S/N - FFK1-UP
S/N - GGE1-UP
S/N - GGH1-UP
S/N - HAS1-UP
S/N - HHK1-UP
S/N - J2F1-UP
S/N - JBT1-UP
S/N - JLP1-UP
S/N - JTN1-UP
1/13
2020/5/21

S/N - JWR1-UP
S/N - KDJ1-UP
S/N - LMG1-UP
S/N - LRM1-UP
S/N - M3M1-UP
S/N - M3N1-UP
S/N - M4T1-UP
S/N - MDS1-UP
S/N - MEY1-UP
S/N - MPL1-UP
S/N - MWP1-UP
S/N - MYG1-UP
S/N - MYP1-UP
S/N - NBD1-UP
S/N - NBN1-UP
S/N - PGW1-UP
S/N - PPN1-UP
S/N - PRF1-UP
S/N - PTB1-UP
S/N - RAS1-UP
S/N - T2Y1-UP
S/N - THJ1-UP
S/N - TLY1-UP
S/N - W3K1-UP
S/N - WDC1-UP
S/N - WET1-UP
2/13
2020/5/21

S/N - WRK1-UP
S/N - XBH1-UP
S/N - YCF1-UP
S/N - ZCT1-UP
S/N - ZML1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded Rod M12 x 1.75 X 250 mm (10 in) long 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G 9S-3263 Thread Lock Compound -
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
3/13
2020/5/21

1. Install O-ring seal (35) onto the housing of the travel motor.
2. Install seal (34) and piston actuator (33) .
3. Install backup ring (32) and seal (31) .
4/13
2020/5/21

4. Install cover (30) and bolts (29) . Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
5. Apply Tooling (G) to the mating surface of seal (28) . Use Tooling (E) in order to install
seal (28) .
6. Use Tooling (F) in order to install retaining ring (27) .
5/13
2020/5/21

7. Rotate the housing.
8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25) .
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel. Install ball (23) onto springs (24) .
6/13
2020/5/21

11. Install piston assemblies and retainer plate (22) into barrel assembly (21) .
Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
12. Install cam plate (20) onto barrel assembly (21) .
7/13
2020/5/21

13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15) .
14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15) .
15. Install bearing race (18) onto shaft (15) .
Note: Bearing race (18) must contact retaining ring (17) .
8/13
2020/5/21

16. Install Tooling (C) into shaft (15) . Install shaft (15) into rotating assembly (16) .
17. Place the pump housing into Tooling (A) .
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
9/13
2020/5/21

19. The notches in cam plate (20) must align with keys (26) . The keys are located in the bottom
of the housing of the travel motor.
20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
10/13
2020/5/21

21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
23. Rotate brake piston (8) .
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
11/13
2020/5/21

25. Install springs (7) and O-ring seals (6) .
26. Install O-ring seal (3) , port plate (4) , and bearing (5) .
27. Install head (2) onto the body of the travel motor.
12/13
2020/5/21

Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1) . Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By: Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu May 21 21:36:45 UTC+0800 2020
13/13
2020/5/21

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR W3K
Configuration: 336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i03808350
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/4
2020/5/21

2. Install new O-ring seal (6) . Apply clean hydraulic oil on the O-ring seal.
3. Attach a suitable lifting device to travel motor (4) , as shown.
4. The weight of the travel motor is approximately 57 kg (125 lb).
2/4
2020/5/21

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

5. Carefully install travel motor (4) onto Tooling (A) . Slide the travel motor into the final
drive.
6. Install one of three bolts (5) that secures the travel motor to the final drive.
7. Remove Tooling (A) .
Typical example
8. Install remaining bolts (2) .
9. Connect hose assembly (3) . Connect hose assembly (1) .
10. Fill the final drive with oil.
ReferenceRefer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
ReferenceRefer to Operation and Maintenance Manual, "Final Drive Oil Level - Check" for
the correct filling procedure.
11. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
12. Obtain a hydraulic oil sample from the main S·O·S port.
ReferenceRefer to Operation and Maintenance Manual, "Sampling Interval and Location of
Sampling Valve" for the correct location.
13. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
ReferenceRefer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 322C Hydraulic Excavators" for further information.
3/4
2020/5/21

Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual Instant Download.pdf

More Related Content

Similar to Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual Instant Download.pdf (6)

More from ze3xiandiao (20)

Recently uploaded (20)

Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual Instant Download.pdf