Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001 and up).pdf

Service Repair Manual
Models
345D L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D L EXCAVATOR PBT
Configuration: 345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i05872085
Swing Drive - Disassemble
SMCS - 5459-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B 1P-2420 Transmission Repair Stand 1
C
5P-5197 Retaining Ring Pliers 1
1U-8759 Tip Set 1
D 1P-0510 Drive Group 1
Start By:
A. Remove the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Remove and
Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00724836
1. Fasten Tooling (A) and a suitable lifting device to the swing drive.
2. Place the swing drive onto Tooling (B) . The weight of the swing drive is approximately
290 kg (640 lb).
3. Open the drain valve and drain the oil from the swing drive into a suitable container for
storage or disposal. The capacity of the swing drive is 11 L (2.9 US gal). If necessary,
remove the drain valve from the swing drive housing.
4. Remove oil level gauge (Dipstick) (1) , filler breather cap assembly, and hose assembly (2)
from the swing drive.
2/12
2020/6/25

5. Remove fitting (3) from cover (5) .
6. Remove bolts (4) and the washers from cover (5) .
7. Attach Tooling (A) to cover (5) . Remove cover (5) .
3/12
2020/6/25

8. Remove sun gear (6) from the carrier assembly (7) .
9. Remove spacer (8) from carrier assembly (7) .
10. Remove carrier assembly (7) from the swing drive.
11. Disassemble carrier assembly (7) , as follows:
a. Use a hammer and a punch in order to drive spring pin (9) into planetary shaft (10) .
4/12
2020/6/25

b. Remove planetary shaft (10) , thrust washer (11) , thrust washer (14) , and planetary
gear (12) from the carrier assembly.
c. Remove bearing (13) from planetary gear (12) .
d. Use a hammer and a punch in order to remove spring pin (9) from the planetary shaft
(10) .
e. Repeat Steps 11.a through 11.d in order to remove the other planetary gears from the
carrier assembly.
12. Use a screwdriver in order to remove upper retaining ring (15) from sun gear (16) .
13. Remove carrier assembly (7) from sun gear (17) .
5/12
2020/6/25

14. Remove retaining ring (17) from the sun gear.
15. Attach Tooling (A) to ring gear (18) .
16. Remove ring gear (18) from the swing drive housing (19) . The weight of ring gear (18) is
approximately 36 kg (80 lb).
6/12
2020/6/25

17. Remove spacer (20) from carrier assembly (21) .
18. Use two screwdrivers in order to remove retaining ring (22) .
19. Use two persons to remove carrier assembly (21) . The weight of carrier assembly (21) is
20. Disassemble carrier assembly (21) , as follows:
7/12
2020/6/25

a. Use a hammer and a punch to drive spring pin (23) into planetary shaft (24) .
b. Remove planetary shaft (24) , thrust washer (25) , thrust washer (29) , and planetary
gear (27) from the carrier assembly.
c. Remove bearing (26) and (28) from planetary gear (27) .
d. Use a hammer and a punch to remove spring pin (23) from planetary shaft (24) .
e. Repeat Steps 20.a through 20.d in order to remove the other planetary gears from the
carrier assembly.
8/12
2020/6/25

21. Use Tooling (C) to remove retaining ring (30) .
22. Place swing drive housing (19) sideways. Remove bolts (32) and the washers from bearing
cage (31) .
9/12
2020/6/25

23. Put swing drive housing (19) into a suitable press. The combined weight of swing drive
housing (19) , pinion shaft (33) (not shown), and bearing cage (31) (not shown) is
24. Place suitable blocking under pinion shaft (33) (not shown). This will prevent the pinion
shaft from falling while the shaft is pressed out of the swing drive housing.
25. Push the pinion shaft from swing drive housing (19) .
26. Remove swing drive housing (19) and the pinion shaft from the suitable press. The weight
of swing drive housing (19) is approximately 111 kg (245 lb). The weight of pinion shaft
(33) is approximately 41 kg (90 lb).
27. Place swing drive housing (19) sideways.
28. Remove bearing cage (31) from the swing drive housing (19) .
29. Remove lip seals (34) from bearing cage (31) .
30. Remove O-ring seal (35) from bearing cage (31) .
10/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/6/25

31. Remove bearing inner race (36) from the smaller bearing.
32. Use the following procedure to remove bearing assembly (37) , spacer (38) , and bearing
assembly (39) .
11/12
2020/6/25

a. Place the bearings and the swing drive housing in a suitable press.
b. Use Tooling (D) and spacer (38) in order to remove bearing assembly (39) from the
swing drive housing. The weight of swing drive housing (19) is approximately 73 kg
(160 lb).
Note: Use care when components are pushed from the swing drive housing. Avoid
injury to personnel. Also, avoid damage to components.
Note: Bearing assembly (39) will be damaged upon the removal.
c. Rotate the swing drive housing to the other side. Remove bearing assembly (37) from
swing drive housing (19) .
Note: Push the outer race in order to prevent damage to bearing assembly (37) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 25 17:00:59 UTC+0800 2020
12/12
2020/6/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02406626
Swing Drive - Assemble
SMCS - 5459-016
Assembly Procedure
Table 1
Required Tools
A 138-7574 Link Bracket 2
B 1P-2420 Transmission Repair Stand 1
C
5P-5197 Retaining ring pliers 1
1U-8759 Tip Set 1
D 1P-0510 Drive Group 1
E 1U-6396 O-Ring Assembly Compound 1
F 5P-3931 Anti-Seize Compound 1
G 5P-0960 Grease Cartridge 1
H 9S-3263 Thread Lock Compound 1
J 1U-8846 Gasket Sealant 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
1/13
2020/6/25

Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use Tooling (E) during the assembly procedure.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Make sure that all parts of the swing drive are thoroughly clean and free of dirt and debris
prior to assembly.
2. ApplyTooling (F) on the outside diameter of bearing (37) and the inside diameter of swing
drive housing (19).
3. Lower the temperature of bearing (37). Install bearing (37) in the swing drive housing. It
may be necessary to use a hammer and a punch to properly seat the bearing in the swing
drive housing.
2/13
2020/6/25

4. Install O-ring seal (35) into bearing cage (31).
5. Install lip seals (34) in bearing cage (31).
6. ApplyTooling (G) on the lip of each seal.
7. Carefully install cage (31) over pinion shaft (33).
8. Raise the temperature of bearing (39) and install bearing (39) on pinion shaft (33).
3/13
2020/6/25

9. Install spacer (38) on top of bearing assembly (37), as shown.
Note: Lip (e) for spacer (38) must face opposite bearing assembly (37), as shown.
10. Put swing drive housing (19) in a suitable press.
11. Apply Tooling (F) on the outside diameter of bearing assembly (39) and the inside diameter
of the swing drive housing.
12. Install pinion shaft (33), bearing cage (31), bearing assembly (39), through spacer (38) and
bearing (37).
Note: It may be necessary to reposition the press so that bearing assembly (39) is installed
evenly into the swing drive housing.
Note: Align bearing cage (31) with the swing drive housing during installation of the pinion
shaft. Temporarily install bolts that will hold bearing cage (31) to the swing drive housing.
4/13
2020/6/25

13. Remove the swing drive from a suitable press and place the swing drive sideways. The
combined weight of the swing drive housing, the pinion shaft, and the bearing cage is
14. Remove the temporary bolts that are holding the bearing cage in position.
15. ApplyTooling (H) on the threads of bolts (32) that hold bearing cage (31) to swing drive
housing (19).
16. Tighten bolts (32) to a torque of 100 ± 20 N·m (75 ± 15 lb ft).
17. Raise the temperature of bearing inner race (36) and install bearing inner race (36) on the
pinion shaft (33).
Note: Make sure that the shaft is centered in the swing drive housing, before you install
bearing inner race (36).
5/13
2020/6/25

18. Use Tooling (C) to install retaining ring (30).
19. Assemble the carrier assembly (21), as follows:
a. Apply clean SAE 30W oil on bearing (26) and bearing (28). Install bearings (26) and
(28) into planetary gear (27).
b. Install thrust washer (25) on one side of planetary gear (27).
c. Install thrust washer (29) on the other side of planetary gear (27).
d. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
e. Install planetary gear (27) and the thrust washers in the carrier assembly (21).
6/13
2020/6/25

f. Install planetary shaft (24) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
g. Drive spring pin (23) into planetary shaft (24). Orient the split in spring pin (23)
vertically to the carrier. Align the split in the spring pin to the top or to the bottom.
Make a stake mark on each side of the spring pin hole in the carrier. Each stake mark
should be approximately 2.25 ± 0.75 mm (0.090 ± 0.030 inch) from the outside
diameter of the spring pin hole.
h. Repeat Steps 19.a through 19.g in order to install the other three planetary gears (27)
in the carrier assembly.
7/13
2020/6/25

20. Use two persons and install carrier assembly (21) into the housing. The weight of carrier
assembly (21) is approximately 40 kg (88 lb).
21. Install retaining ring (22).
22. Install spacer (20) into carrier assembly (21).
8/13
2020/6/25

23. Make sure that the mating surfaces of ring gear (18) and swing drive housing (19) are
thoroughly clean.
24. Apply Tooling (J) to the face of swing drive housing (19) and the face of ring gear (18).
25. Install Tooling (A) onto ring gear (18). The weight of ring gear (18) is approximately 36 kg
(80 lb).
26. Install ring gear (18) onto the swing drive housing (19).
27. Install retaining ring (17) into the sun gear.
9/13
2020/6/25

28. Install carrier assembly (7) into the sun gear. Install retaining ring (15) into sun gear (16).
29. Assemble carrier assembly (7), as follows:
a. Apply clean SAE 30W oil on bearing (13). Install bearing (13) in planetary gear (12).
b. Install a thrust washer (11) on one side of planetary gear (12).
c. Install a thrust washer (14) on the other side of planetary gear (12).
d. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
e. Install planetary gear (12) and the thrust washers in the carrier assembly (7).
f. Install planetary shaft (10) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
10/13
2020/6/25

g. Drive spring pin (9) into planetary shaft (10). Orient the split in spring pin (9)
vertically to the carrier. Align the split in the spring pin to the top or to the bottom.
Make a stake mark on each side of the spring pin hole in the carrier. Each stake mark
should be approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside diameter
of the spring pin hole.
h. Repeat Steps 29.a through 29.g for the remaining gear assemblies.
30. Install carrier assembly (7) in the ring gear.
31. Install spacer (8) into carrier assembly (7).
11/13
2020/6/25

32. Install sun gear (6) into carrier assembly (7).
33. Make sure that the mating surfaces of the ring gear and cover (5) are thoroughly clean.
34. Apply on the flange surface of the ring gear and cover (5).
35. Fasten Tooling (A) and a suitable lifting device to cover (5). Put the cover in the original
position on the ring gear. Make sure that the cover is seated properly.
12/13
2020/6/25

36. ApplyTooling (H) on the threads of bolts (4).
37. Install the washers and bolts (4) that hold the cover, the ring gear, and the swing drive
housing together. Tighten bolts (4) to a torque of 270 ± 40 N·m (200 ± 30 lb ft).
38. Install fitting (3) into cover (5).
39. Install oil level gauge (Dipstick) (1), filler breather cap assembly, and hose assembly (2) to
the swing drive.
40. If the drain valve was removed from the swing drive housing, reinstall the drain valve.
End By:
a. Install the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Install".
Thu Jun 25 17:01:56 UTC+0800 2020
13/13
2020/6/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07188254
Swing Drive - Install
SMCS - 5459-012
Installation Procedure
Table 1
Required Tools
A 439-3939 Link Bracket As 2
C 5P-3931 Anti-Seize Compound -
D 1U-8846 Gasket Sealant -
E - Loctite 243 -
1/3
2020/6/25

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Note: During the installation procedure, the locating pin for the swing drive may come out
of the swing drive housing.
1. Thoroughly clean the mating surfaces of swing drive (2) and the main frame. Apply Tooling
(C) to the pin that locates swing drive (2) in the main frame. Apply Tooling (D) to the
mating surfaces of swing drive (2) and the main frame.
2. Attach Tooling (A) and a suitable lifting device onto swing drive (2). The weight of swing
drive (2) is approximately 290 kg (640 lb). Position swing drive (2) onto the locating pin on
the main frame.
3. Install corks (3). Remove Tooling (A).
2/3
2020/6/25

4. Apply Tooling (E) to the threads of bolts (1). Install bolts (1). Tighten bolts (1) to a torque
of 250 ± 25 N·m (184 ± 18 lb ft). Turn an additional angle of 45 ± 5 degrees.
5. Refer to Service Magazine , M0083843 , "An Improved Bolt Tightening Procedure for the
Critical Joints Is Now Used on all Excavators" for more detailed information.
6. Fill the swing motor with oil. Refer to Operation and Maintenance Manual, "Swing Drive
Oil - Change".
End By:
a. Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install".
Thu Jun 25 17:02:54 UTC+0800 2020
3/3
2020/6/25

Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001 and up).pdf

More Related Content

Similar to Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001 and up).pdf (13)

More from ufs89eodkdmdm (20)

Recently uploaded (20)

Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001 and up).pdf