Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx00001 and up)

Service Repair Manual
Models
349E L and 349E L VG
Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L VG EXCAVATOR KFX
Configuration: 349E L Excavators KFX00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator Machine Systems
Media Number -KENR9848-04 Publication Date -01/10/2012 Date Updated -23/10/2012
i04243909
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B - Bolt M4 x 0.7 1
C 6V-3010 Puller Gp 1
D 3E-3879 Eyebolt 1
E 9S-9152 Bearing Puller Gp 1
Start By:
a. Remove the travel motor.
1. Drain the travel motor.
1/10
349E L Excavators KFX00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/10/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g02419258
2. Remove O-ring seal (1) from motor housing (2).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Attach Tooling (A) onto head assembly (3). Remove bolts (4). Use Tooling (A) and a
suitable lifting device to remove head (3). The weight of head assembly (3) is
approximately 40 kg (90 lb).
2/10
2020/10/2

4. Remove plate (5) from head (3).
5. Remove bearing (6) from head assembly (3).
6. Remove orifice (7), spring (8), and ball (9).
7. Remove O-ring seal (10) from head assembly (3).
3/10
2020/10/2

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove adapter (11), spool (12), and spring (13) from head assembly (3).
9. Use Tooling (B) in order to remove retainers (14) from head assembly (3).
10. Remove O-ring seals (16) and backup rings (15) from adapters (14).
11. Remove balls (17) from head assembly (3).
12. Remove springs (18) from brake housing (20).
4/10
2020/10/2

13. Remove O-ring seals (19) from motor housing (2).
14. Use Tooling (C) in order to remove brake housing (20) from motor housing (2).
15. Remove backup ring (21) and O-ring seal (22) from brake piston (20).
16. Remove O-ring seal (23) and backup ring (24) from brake piston (20).
5/10
2020/10/2

17. Attach Tooling (D) to shaft assembly (25).
18. Use Tooling (D) and a suitable lifting device in order to lift the rotating group from motor
housing (2). The weight of the rotating group is approximately 30 kg (65 lb).
19. Remove plates (26) and friction disks (27) from barrel assembly (28).
6/10
2020/10/2

20. Remove barrel assembly (28) and swashplate (29) from shaft assembly (25).
21. Remove plate (31) and pistons (30) from barrel assembly (28).
7/10
2020/10/2

22. Remove bearing (32), thin shim (33), Belleville washers (34), and barrel spacer (35) from
barrel assembly (28).
23. Use a suitable press in order to remove bearing (36) from shaft assembly (25).
8/10
2020/10/2

24. Use Tooling (E) and a suitable press in order to remove inner race (37) from shaft assembly
(25).
9/10
2020/10/2

25. Remove keys (38) and pins (39) from motor housing (2).
26. Remove plug (40) and the O-ring seal. Remove actuator piston (41).
27. Remove retaining ring (42) and seal (43) from motor housing (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 2 10:47:01 UTC+0800 2020
10/10
349E L Excavators KFX00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/10/2

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i06563923
Travel Motor - Assemble
SMCS - 4351-016
Specifications
NOTICE
To prevent damage to the motor, the case must be filled with clean
hydraulic oil at least to the fill port before operation.
1/13
2020/10/2

Table 1
Specification for 390-1088 Travel Motor Gp
Item Qty Part Specification Description
1 1 5P-7684 Plug Torque to 430 ± 40 N·m (317 ± 30 lb ft).
2 1
6K-6307 O-
Ring Seal
Lubricate with 1U-6396 O-Ring Assembly Compound.
- - -
Before assembly, lubricate the sliding surfaces of the cam plate
(3), the hold-down (4), the pistons (5), the barrel (6) and the shaft
(8) lightly with clean hydraulic oil.
7 20
124-1561 Brake
Spring
Length under test force is 19.0 mm (0.75 inch).
Test force is 425 ± 43 N (96 ± 10 lb).
Free length after test is 22.06 mm (0.869 inch).
9 1
6V-3382 Lip
Type Seal
Apply blue Loctite 243 to the outside diameter.
10 1
118-5805
Special Race
Bearing
Install the snap ring of the special race bearing toward the shaft
flange.
11 2
9S-4185 O-
Ring Plug
Torque to 82 ± 8 N·m (60 ± 6 lb ft).
12 6 8T-4187 Bolt Torque to 530 ± 70 N·m (391 ± 52 lb ft).
13 2
9S-4183 O-
Ring Plug
Torque to 190 ± 20 N·m (140 ± 15 lb ft).
Section A-A
Table 2
2/13
2020/10/2

14 2
1T-0936 Pipe
Plug
Install in the orifice toward the head surface or below the head
surface.
15 1 124-1554 Spring
Length under test force is 15 mm (0.6 inch).
Test force is 15.0 ± 2.0 N (3.4 ± 0.4 lb).
Free length after test is 16.15 mm (0.636 inch).
D - -
Depth from the head and interface of the port plate is
20.0 ± 0.2 mm (0.79 ± 0.01 inch).
16 1
195-4456 Orifice
Plug
Torque to 7 ± 1 N·m (62 ± 9 lb in).
Section C-C
Table 3
17 1 230-5483 Spring
Length under test force is 25 mm (1.0 inch).
Test force is 60.0 ± 8.0 N (13.5 ± 1.8 lb).
Free length after test is 35 mm (1.4 inch).
18 1 087-4786 Adapter Torque to 115 ± 10 N·m (85 ± 7 lb ft).
Assembly Procedure
Table 4
Required Tools
A 138-7573 Link Bracket 1
D 3E-3879 Eyebolt 1
3/13
2020/10/2

F 1U-6396 O-Ring Assembly Compound 1
G - Loctite 242 -
H 1P-0510 Driver Gp 1
J 6V-2055 Grease 1
K 128-5049 Guide Stud 2
1. Lubricate actuator piston (41) with the oil that is being used. Install actuator piston (41) into
housing (2). Apply Tooling (F) onto O-ring seal of plug (40). Install plug (40) into motor
housing (2).Tighten plug (42) to a torque of 430 ± 40 N·m (315 ± 30 lb ft).
2. Apply Tooling (G) onto outside diameter of seal (43). Use Tooling (H) to install seal (43).
Install retaining ring (42).
4/13
2020/10/2

3. Install pins (39) and keys (38) into motor housing (2).
4. Use a suitable press to install bearing (36) and bearing (37) onto shaft assembly (25). Bearing
(36) must be installed with Retaining Clip (X) toward the barrel assembly.
5/13
2020/10/2

5. Install barrel spacer (35), Belleville washers (34), thin shim (33), and bearing (32) onto barrel
assembly (28).
6/13
2020/10/2

6. Install pistons (30) and plate (31) onto barrel assembly (28).
7. Install swashplate (29) and barrel assembly (28) onto shaft assembly (25).
7/13
2020/10/2

8. Use Tooling (D) and a suitable lifting device to install the rotating group into motor housing
(2). The weight of the rotating group is approximately 30 kg (65 lb).
Note: Align the notches of swashplate (29) with the keys in the motor housing (2).
Note: Protect shaft seal (43) from damage by covering the splines on shaft assembly (25) with
heat shrink tubing.
8/13
2020/10/2

9. Install plates (26) and friction discs (27). Start with plate (26). Alternate between plates (26)
and friction discs (27) with plates (26) on the top and the bottom.
10. Install backup ring (21) and O-ring seal (22) onto brake piston (20).
11. Install backup ring (24) and O-ring seal (23) onto brake piston (20).
12. Install O-ring seals (19) onto motor housing (2). Install springs (18) onto brake piston (20).
9/13
2020/10/2

13. Install balls (17), backup rings (15), O-ring seals (16), and retainers (14) into head assembly
(3).
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install spring (13), spool (12), and adapter (11). Tighten adapter (11) to a torque of
115 ± 10 N·m (85 ± 7 lb ft).
10/13
2020/10/2

15. Install ball (9), spring (8), and orifice (7). Tighten orifice (7) to a torque of 7 ± 1 N·m
(62 ± 9 lb in).
16. Install bearing (6) and O-ring seal (10) onto head assembly (3).
17. Apply Tooling (K) to the back side of plate (5) to hold plate (5) in place during assembly.
Install plate (5) to head assembly (3).
11/13
2020/10/2

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
18. Install Tooling (K) onto motor housing (2). Use Tooling (A) and a suitable lifting device to
install head assembly (3) onto motor housing (2).The weight of the head (3) is approximately
40 kg (90 lb). Remove Tooling (A) and Tooling (D). Install bolts (4). Tighten bolts (4) to a
torque of 530 ± 70 N·m (390 ± 50 lb ft).
12/13
2020/10/2

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

19. Install O-ring seal (1) onto motor housing (2).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 2 10:47:57 UTC+0800 2020
13/13
2020/10/2

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07186913
Final Drive and Travel Motor - Remove and Install
SMCS - 4050; 4351
Removal Procedure
Table 1
Required Tools
A 1U-9200 Lever Puller Hoist 1
B 439-3941 Link Brackets 2
C - Loctite 243 -
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change" for the correct
draining and filling procedures.
1/4
2020/10/2

2. Release the track tension. Refer to Operation and Maintenance Manual, "Track Adjustment
- Adjust".
3. Start the machine. Position track roller (1) on suitable cribbing. Position pin to separate the
track above the final drive.
4. Separate the track.
5. Remove the counterbalance valve.
2/4
2020/10/2

Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx00001 and up)

More Related Content

Similar to Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx00001 and up) (11)

More from cdsaas (20)

Recently uploaded (20)

Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx00001 and up)