Caterpillar cat 385 c fs excavator (prefix mma) service repair manual (mma00001 and up)

Service Repair Manual
Models
385C FS Excavator

Shutdown SIS
Previous Screen
Product: FRONT SHOVEL
Model: 385C FRONT SHOVEL MMA
Configuration: 385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine
Disassembly and Assembly
C15 and C18 Engines for Caterpillar Built Machines
Media Number -RENR8261-28 Publication Date -01/08/2015 Date Updated -28/08/2018
i02905549
Valve Actuator (Variable) - Remove
SMCS - 1105-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Note: Do not disassemble the variable valve actuator after the component has been removed. Any
attempt to disassemble the variable valve actuator will void the warranty of the component.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
1/3
385C FS Excavator MMA00001-UP (MACHINE) POWERED BY C-18 Engine(SEB...
2020/10/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01446246
1. Disconnect harness assembly (4). Disconnect harness assembly (1).
2. Remove bolt (2). Remove four nuts (3) and two nuts (6).
3. Remove variable valve actuator (5).
4. Remove support (11) and stud (10).
2/3
2020/10/12

5. Remove two studs (9) and three studs (7).
6. Remove rocker arm assembly (8).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 12 11:41:36 UTC+0800 2020
3/3
2020/10/12

Shutdown SIS
Previous Screen
i02905633
Valve Actuator (Variable) - Install
SMCS - 1105-012
Installation Procedure
NOTICE
1/3
2020/10/12

1. Install two studs (9) at Location 6 and Location 7. Tighten studs (9) to a torque of
47 ± 9 N·m (35 ± 7 lb ft).
2. Install stud (10) at Location 2. Tighten stud (10) to a torque of 65 ± 10 N·m (48 ± 7 lb ft).
Install support (11).
3. Position rocker arm assembly (8). Install three studs (7) at Location 3, Location 4, and
Location 5. Tighten studs (7) to a torque of 50 ± 5 N·m (37 ± 4 lb ft). Turn studs (7) for an
additional 45 ± 5 degrees.
4. Install variable valve actuator (5).
5. Install bolt (2). Install four nuts (3). Install two nuts (6). Refer to the tightening sequence.
6. Tighten bolt (2) to a torque of 105 ± 20 N·m (77 ± 15 lb ft). Tighten nuts (3) to a torque of
105 ± 20 N·m (77 ± 15 lb ft). Tighten nuts (6) to a torque of 47 ± 9 N·m (35 ± 7 lb ft).
Tighten the nuts and the bolt in a numerical sequence.
7. Connect harness assembly (4). Connect harness assembly (1) to variable valve actuator (5).
2/3
2020/10/12

8. First adjust the lash on the exhaust and then adjust the compression brake on variable valve
actuator (5). Refer to Testing and Adjusting, "Compression Brake Lash - Adjust" for more
information on adjusting the lash for the compression brake. Tighten jam nut (12) to a
torque of 15 ± 3 N·m (11 ± 2 lb ft).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Mon Oct 12 11:42:33 UTC+0800 2020
3/3
2020/10/12

Shutdown SIS
Previous Screen
i02906282
Rocker Arm and Shaft - Remove
SMCS - 1102-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 124-2946 Lifting Bracket 1
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
B. Remove the variable valve actuator, if necessary. Refer to Disassembly and Assembly,
"Valve Actuator (Variable) - Remove".
NOTICE
1/2
2020/10/12

1. Remove bolts (2) .
2. Use Tooling (A) to remove rocker arm shaft assembly (4) , valve rocker arms (3) , and
electronic unit injector rocker arms (1) as a unit.
Mon Oct 12 11:43:30 UTC+0800 2020
2/2
2020/10/12

Shutdown SIS
Previous Screen
i04997049
Rocker Arm - Disassemble
SMCS - 1123-015
Disassembly Procedure
Start By:
a. Remove the rocker arms and the rocker shaft. Refer to Disassembly and Assembly, "Rocker
Arm and Shaft - Remove".
NOTICE
1/2
2020/10/12

1. Remove valve rocker arms (11) and electronic unit injector rocker arm (3) from rocker shaft
assembly (4).
2. Remove jam nut (7) from adjustment screw (8).
3. Remove adjustment screw (8) from valve rocker arms (11).
4. Remove button (10) from adjustment screw (8). Remove O-ring seal (9) from the
adjustment screw.
5. Remove jam nut (2) from unit injector adjustment screw (1).
6. Remove unit injector adjustment screw (1) from electronic unit injector rocker arm (3).
7. Remove button (6) from unit injector adjustment screw (1). Remove O-ring seal (5) from
the unit injector adjustment screw.
Mon Oct 12 11:44:26 UTC+0800 2020
2/2
2020/10/12

Shutdown SIS
Previous Screen
i04998150
Rocker Arm - Assemble
SMCS - 1123-016
Assembly Procedure
NOTICE
1/2
2020/10/12

Note: Do not reuse the O-ring seal on the adjustment screw if the button is removed from
the adjustment screw.
1. Install O-ring seal (9) in button (10).
2. Use a soft hammer to seat button (10) on adjustment screw (8).
3. Install adjustment screw (8) in valve rocker arms (11). Install jam nut (7) on the adjustment
screw.
4. Install O-ring seal (5) in button (6).
5. Use a soft hammer to seat button (6) on unit injector adjustment screw (1).
6. Install unit injector adjustment screw (1) in electronic unit injector rocker arm (3). Install
jam nut (2) on the unit injector adjustment screw.
7. Lubricate rocker shaft assembly (4) with clean engine oil.
8. Install valve rocker arms (11) and electronic unit injector rocker arm (3) on rocker shaft
assembly (4).
End By:
a. Install the rocker arms and the rocker shaft. Refer to Disassembly and Assembly, "Rocker
Arm and Shaft - Install".
Mon Oct 12 11:45:23 UTC+0800 2020
2/2
2020/10/12

Shutdown SIS
Previous Screen
i07394739
Rocker Arm and Shaft - Install
SMCS - 1102-012
Table 1
Required Tools
A 124-2946 Lifting Bracket 1
NOTICE
1/3
2020/10/12

1. Position rocker arm shaft assembly (4), valve rocker arms (3), and electronic unit injector
rocker arms (1) as a unit with Tooling (A) on the cylinder head.
Note: Apply clean engine oil to the underside of the bolt heads prior to installation.
2/3
2020/10/12

2. Install bolts (2) and tighten to a torque of 55 ± 5 N·m (41 ± 4 lb ft). Tighten bolts (2) again
to a torque of 55 ± 5 N·m (41 ± 4 lb ft). Turn bolts (2) for an additional 60 ± 5 degrees.
Tighten the bolts in the following sequence: 2, 3, 1, 4.
3. Adjust the electronic unit injectors. Refer to Testing and Adjusting, "Electronic Unit
Injector - Adjust".
4. Adjust the engine valve lash. Refer to Testing and Adjusting, "Engine Valve Lash-
Inspect/Adjust".
End By:
a. Install the variable valve actuator, if necessary. Refer to Disassembly and Assembly, "Valve
Actuator (Variable) - Install".
b. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Mon Oct 12 11:46:20 UTC+0800 2020
3/3
2020/10/12

Shutdown SIS
Previous Screen
i02211115
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
a. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
b. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
c. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
d. Remove the turbochargers. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/6
2020/10/12

NOTICE
NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
1. Drain the cooling system. Refer to Operation and Maintenance Manual, "Cooling System
Coolant - Change".
2. Remove bolts (2) and thrust plate (1).
2/6
2020/10/12

3. Remove sealing plate (3) and adapter assembly (4).
4. Remove O-ring seal (5) and O-ring seal (6) from sealing plate (3).
3/6
2020/10/12

5. Disconnect hose assembly (8).
6. Disconnect hose assembly (12).
7. Remove bolts (10). Position fuel filter base (9) out of the way.
8. Remove bolt (11) and the breather tube from the cylinder head.
9. Remove bolts (7) and remove the bracket from the cylinder head.
10. Disconnect boost pressure sensor (13).
11. Disconnect inlet air temperature sensor (14).
4/6
2020/10/12

12. Remove water temperature regulator housing (17).
13. Remove strap (18).
14. Attach a suitable lifting device to cylinder head (16). The weight of the cylinder head is
approximately 235 kg (518 lb).
15. Remove cylinder head bolts (15).
16. Carefully remove cylinder head (16).
5/6
2020/10/12

17. Remove cylinder head gasket (19).
18. Remove spacer plate (20).
19. Remove seals (24) and seal (22).
20. Remove spacer plate gasket (23).
21. Remove O-ring seal (21) from the dowel in the cylinder block.
Mon Oct 12 11:47:17 UTC+0800 2020
6/6
2020/10/12

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Shutdown SIS
Previous Screen
i04410295
Cylinder Head - Install
SMCS - 1100-012
Table 1
Required Tools
A 6V-4876 Lubricant 1
B 8T-2998 Lubricant 1
C 9S-3263 Thread Lock Compound 1
NOTICE
1/6
2020/10/12

1. Install O-ring seal (21) on the dowel in the cylinder block.
2. Install spacer plate gasket (23) on the cylinder block.
3. Install seals (24) and seal (22) .
4. Install spacer plate (20) .
5. Install cylinder head gasket (19) on the spacer plate.
2/6
2020/10/12

6. Attach a suitable lifting device to cylinder head (16) . The weight of the cylinder head is
approximately 235 kg (518 lb).
7. Carefully install cylinder head (16) on the dowel pins on the cylinder block.
3/6
2020/10/12

Caterpillar cat 385 c fs excavator (prefix mma) service repair manual (mma00001 and up)

More Related Content

Similar to Caterpillar cat 385 c fs excavator (prefix mma) service repair manual (mma00001 and up)(20)

More from fjkskefksmeme(20)

Recently uploaded(20)

Caterpillar cat 385 c fs excavator (prefix mma) service repair manual (mma00001 and up)