Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe00001 and up)

Service Repair Manual
Models
385C L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 385C L EXCAVATOR SBE
Configuration: 385C L Excavator SBE00001-UP (MACHINE) POWERED BY C-18 Engine
Disassembly and Assembly
385C Excavator and 385C MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8620-05 Publication Date -01/02/2012 Date Updated -20/02/2012
i02565371
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7575 Link Bracket 3
C 138-7576 Link Bracket 2
D
132-8119 Hydraulic Wrench 1
132-8223 Hydraulic Pump and Motor Gp 1
9U-7418 Hex Bit Socket 1
E 176-6536 Forcing Bolt 2
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
1/12
385C L Excavator SBE00001-UP (MACHINE) POWERED BY C-18 Engine(SEBP42...
2020/9/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01284546
1. Fasten final drive (1) to Tooling (A). Put an alignment mark across the sections of final
drive (1) for assembly purposes. All parts must be reinstalled in the original locations. The
weight of final drive (1) is approximately 1020 kg (2250 lb).
2. Remove socket setscrews (2) from housing cover (3) .
2/12
2020/9/29

3. Fasten Tooling (B) and a suitable lifting device to housing cover (3) .
4. Remove bolts (4) and the washers. Use a soft faced hammer in order to break the seal
between housing cover (3) and the ring gear. Remove housing cover (3). The weight of
housing cover (3) is approximately 95 kg (210 lb).
5. Remove spacer (5) and the shims from housing cover (3) .
6. Remove socket head bolts (6) and ring gear (7) from housing cover (3) .
7. Remove sun gear (8) .
3/12
2020/9/29

8. Use Tooling (B) and a suitable lifting device in order to remove carrier assembly (9). The
weight of carrier assembly (9) is approximately 43 kg (95 lb).
9. Remove retaining ring (10), spacer (11), and sun gear (12) .
4/12
2020/9/29

10. Drive spring pin (14) into planetary shaft (15). Remove planetary shaft (15) and planetary
gear assembly (13) .
11. Remove washers (16) and bearing (17) from planetary gear (18). Remove spring pin (14)
from planetary shaft (15) .
12. Repeat Steps 10 and 11 for the remaining planetary gear assemblies.
13. Use Tooling (B) and a suitable lifting device in order to remove carrier assembly (19). The
5/12
2020/9/29

14. Remove retaining ring (20), spacer (21), and sun gear assembly (22) .
6/12
2020/9/29

16. Remove washers (28) and bearing (27) from planetary gear (26). Remove spring pin (23)
from planetary shaft (25) .
18. Remove spacer (30). Use Tooling (B) and a suitable lifting device in order to remove carrier
assembly (29). The weight of carrier assembly (29) is approximately 132 kg (290 lb).
7/12
2020/9/29

20. Remove washers (34) and (38), and bearings (35) and (37) from planetary gear (36).
Remove spring pin (32) from planetary shaft (33) .
22. Use Tooling (B) and a suitable lifting device in order to remove ring gear (39) from housing
(40). The weight of ring gear (39) is approximately 155 kg (340 lb).
8/12
2020/9/29

23. Remove O-ring seal (41) from housing (40) .
24. Place suitable cribbing under motor housing (42) in order to support motor housing (42) .
9/12
2020/9/29

25. Use Tooling (D) in order to remove bolts (43) from coupling gear (44) .
Note: A part of Tooling (D) must be modified. Cut Length (X) on the Hex Bit Socket to a
length of 14.0 mm (0.55 inch).
26. Install Tooling (E) in coupling gear (44), as shown. Tighten Tooling (E) evenly in order to
loosen coupling gear (44). Remove coupling gear (44) from motor housing (42) .
27. Remove shims (45) from motor housing (42) .
10/12
385C L Excavator SBE00001-UP (MACHINE) POWERED BY C-18 Engine(SEBP...
2020/9/29

28. Remove bolts (46). Use Tooling (C) and a suitable lifting device in order to separate
housing (40) from motor housing (42). Motor housing (42) will rest on the suitable cribbing.
The weight of housing (40) is approximately 250 kg (550 lb).
29. Remove bearing cone (47) from housing (40) .
11/12
2020/9/29

30. Use Tooling (C) and a suitable lifting device in order to flip housing (40) on the other side.
The weight of housing (40) is approximately 250 kg (550 lb).
31. Remove Duo-Cone seal (48), and bearing cups (49) and (50) from housing (40) .
32. Remove pins (51) from motor housing (42), if necessary.
33. Remove bearing cone (52) from motor housing (42) .
34. Remove Duo-Cone seal (53) from motor housing (42) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 29 12:26:31 UTC+0800 2020
12/12
2020/9/29

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 385C L EXCAVATOR SBE
Configuration: 385C L Excavator SBE00001-UP (MACHINE) POWERED BY C-18 Engine
Disassembly and Assembly
385C Excavator and 385C MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8620-05 Publication Date -01/02/2012 Date Updated -20/02/2012
i04956682
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7575 Link Bracket 3
C 138-7576 Link Bracket 2
F 205-8241 Installer 1
G 6V-3175 Double Acting Cylinder 1
3S-6224 Electric Hydraulic Pump Gp 1
1U-9889 Crossblock 1
9S-7338 Crossblock 1
150-1961 Washer 2
150-1786 Plate 2
4C-9634 Puller Stud 1
9U-6832 Nut 1
2K-7468 Locknut 1
4K-0684 Locknut 2
6V-2078 Stud 2
1/17
2020/9/29

5P-4807 Cap 2
H 5P-3931 Anti-Seize Compound 1
J 9S-3263 Thread Lock Compound 1
K 1U-8846 Gasket Sealant 1
L 200-5937 Lubricant 1
M FT-2770 Leak Testing Tool 1
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected at all times.
Note: Check the condition of all the O-ring seals that are used in the final drive. If any of the seals
are worn or damaged, use new parts for replacement.
1. Reassemble the final drive on Tooling (A) and suitable cribbing.
Note: Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber portion of Duo-Cone seal (53) and all surfaces that contact Duo-Cone seal
(53) must be clean and dry. After installation of Duo-Cone seal (53) , apply Tooling (L) on
the contact surfaces of the metal portion of Duo-Cone seal (53) .
2. Use Tooling (F) in order to install Duo-Cone seal (53) .
3. Apply Tooling (H) to the surfaces on motor housing (42) that will contact bearing cone
(52) .
4. Raise the temperature of bearing cone (52) . Use a suitable press in order to install bearing
cone (52) in motor housing (42) .
2/17
2020/9/29

5. Apply Tooling (H) to the surfaces that contact pins (51) . Install pins (51) .
6. Apply Tooling (H) to the surfaces that contact bearing cups (49) and (50) on housing (40) .
Install bearing cups (49) and (50) in housing (40) .
Note: Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber portion of Duo-Cone seal (53) and all surfaces that contact Duo-Cone seal
(48) must be clean and dry. After installation of Duo-Cone seal (48) , apply Tooling (L) on
the contact surfaces of the metal portion of Duo-Cone seal (48) .
Note: Make sure that the Duo-Cone seals (53) and (48) are not scratched or damaged during
the assembly of housing (40) or during the assembly of motor housing (42) . After
installation of housing (40) on the motor housing (42) , there will be a small gap between
the components. The gap is caused by the Duo-Cone seals. The gap will be eliminated
during installation of the gear.
7. Use Tooling (F) in order to install Duo-Cone seal (48) .
3/17
2020/9/29

8. Attach Tooling (C) and a suitable lifting device to housing (40) in order to flip housing (40)
on the other side.
9. Use Tooling (C) and a suitable lifting device in order to install housing (40) on motor
housing (42) . The weight of the housing (40) is approximately 250 kg (550 lb).
10. Install bearing cone (47) .
11. Use the following procedure to determine the bearing preload and the correct number of
shims.
a. Use a depth micrometer in order to measure the step length of coupling gear (44) .
Take measurements at several different locations around gear (44) . Compute the
average of the measured dimensions and record the number. Call this Dimension (X) .
4/17
2020/9/29

b. Use Tooling (G) in order to apply a load of 10700 kPa (1550 psi) to bearing cone (47)
(not shown) and to bearing cone (52) (not shown). The load will seat bearing cone
(47) (not shown) and bearing cone (52) (not shown). A pressure of 10700 kPa (1550
psi) on the electric hydraulic pump of Tooling (G) will result in a pressure of 10000
kg (22050 lb) on bearing cone (47) (not shown) and on bearing cone (52) (not
shown). Rotate the housing in order to seat bearing cone (47) (not shown) and bearing
cone (52) (not shown). Reduce the load on the electric hydraulic pump of Tooling (G)
to 4825 kPa (700 psi).
c. Rotate Tooling (G) by 90° and repeat Step 11.b.
d. Maintain the load on bearing cone (47) (not shown) and on bearing cone (52) (not
shown). Use a depth micrometer and measure the distance between the top face of
housing (42) and bearing cone (47) . Take this measurement in several locations
around bearing cone (47) . Compute the average of the measured dimensions and
record the number. Call this Dimension (Y) .
e. Determine the correct thickness of the shim pack that will be installed between
bearing cone (47) and coupling gear (44) . The shim pack thickness is equal to
Dimension (Y) minus Dimension (X) . Tolerance for the shim pack is 0.10 mm (0.003
inch).
5/17
2020/9/29

Note: If two shims are required, install the thinner shim next to coupling gear (44) when
coupling gear (44) is installed.
12. Place shims (45) in the correct position on motor housing (42) . If two shims were required,
put the thinner shim in contact with coupling gear (44) . Make sure that all of the holes in
the components are in alignment with each other. Put coupling gear (44) in the original
position on the motor housing.
13. ApplyTooling (J) on the threads of bolts (43) . Install bolts (43) in order to secure coupling
gear (44) in place. Tighten bolts (43) evenly and tighten bolts (43) in diagonally opposite
pairs. Tighten bolts (43) to a torque of 900 ± 100 N·m (665 ± 75 lb ft).
6/17
2020/9/29

14. Install O-ring seal (41) in main housing (40) .
15. Use Tooling (C) and a suitable lifting device in order to position housing (40) and motor
housing (42) on Tooling (A) . Remove the suitable cribbing. The weight of both housings is
approximately 430 kg (950 lb).
7/17
2020/9/29

16. Thoroughly clean the mating surface of housing (40) that contacts ring gear (39) . Apply a
bead of Tooling (K) on the mating surface of ring gear (39) . Use Tooling (B) and a suitable
lifting device in order to position ring gear (39) on housing (40) . Make sure that the
alignment mark on housing (40) and ring gear (39) line up with each other. It may be
necessary to use a soft faced hammer to seat ring gear (39) on housing (40) .
17. Assemble planetary gear assembly (31) , as follows:
a. Apply clean SAE 30 oil on bearings (35) and (37) . Install bearings (35) and (37) in
planetary gear (36) .
b. Install washers (34) and (38) on each side of planetary gear (36) .
c. Install planetary gear assembly (31) and washers (34) and (38) in carrier assembly
(29) .
d. Install planetary shaft (33) in carrier assembly (29) and through planetary gear
assembly (31) . Make sure that the spring pin hole in planetary shaft (33) is in
alignment with the spring pin hole in the carrier.
8/17
2020/9/29

e. Install spring pin (32) in the carrier and into planetary shaft (32) . Make sure that the
spring pin hole in planetary shaft (32) is in alignment with the spring pin hole in the
carrier.
f. Orient the split in spring pin (32) as shown. Make a stake mark on each side of the
spring pin hole in the carrier. This will prevent spring pin (32) from falling out of the
spring pin hole. Each stake mark should be approximately to 2.25 ± 0.75 mm (0.089 ±
0.030 inch) from the outside diameter of the spring pin hole.
g. Repeat Steps 17.a through 17.f in order to install the other three planetary gear
assemblies in carrier assembly (29) .
9/17
2020/9/29

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

18. Fasten Tooling (B) and a suitable lifting device to carrier assembly (29) . Put carrier
assembly (29) in position in ring gear (39) . It may be necessary to move carrier assembly
(29) back and forth during installation in order to ensure that all gears engage properly.
19. Install spacer (30) .
20. Assemble planetary gear assembly (24) , as follows:
a. Apply clean SAE 30 oil on bearing (27) . Install bearing (27) in planetary gear (26) .
b. Install washers (28) on each side of planetary gear assembly (24) .
c. Install washers (28) and planetary gear assembly (24) in carrier assembly (19) .
10/17
2020/9/29

d. Install planetary shaft (25) in carrier assembly (19) and through planetary gear
assembly (24) . Make sure that the spring pin hole in planetary shaft (25) is in
alignment with the spring pin hole in the carrier.
e. Orient the split in spring pin (23) as shown. Make a stake mark on each side of the
spring pin hole in the carrier. This will prevent spring pin (23) from falling out of the
spring pin hole. Each stake mark should be approximately to 2.25 ± 0.75 mm (0.089 ±
0.030 inch) from the outside diameter of the spring pin hole.
11/17
2020/9/29

f. Repeat Steps 20.a through 20.e in order to install the other two planetary gear
assemblies in carrier assembly (19) .
21. Install sun gear assembly (22) , spacer (21) , and retaining ring (20) .
22. Use Tooling (B) and a suitable lifting device in order to install carrier assembly (19) . The
12/17
2020/9/29

Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe00001 and up)

More Related Content

What's hot (7)

Similar to Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe00001 and up) (20)

More from fjkskedmme (20)

Recently uploaded (20)

Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe00001 and up)